new file mode 100644
@@ -0,0 +1,18 @@
+* STMicroelectronics STM32 USART
+
+Required properties:
+- compatible: Should be "st,stm32-usart"
+- reg: The address and length of the peripheral registers space
+- interrupts: The interrupt line of the USART instance
+- clocks: The input clock of the USART instance
+- pinctrl: The reference on the pins configuration
+
+Example:
+usart1: usart@40011000 {
+ compatible = "st,stm32-usart";
+ reg = <0x40011000 0x400>;
+ interrupts = <37>;
+ clocks = <&clk_pclk2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart1>;
+};
@@ -1577,6 +1577,23 @@ config SERIAL_MEN_Z135
This driver can also be build as a module. If so, the module will be called
men_z135_uart.ko
+config SERIAL_STM32
+ tristate "STMicroelectronics STM32 serial port support"
+ select SERIAL_CORE
+ depends on ARM || COMPILE_TEST
+ help
+ This driver is for the on-chip Serial Controller on
+ STMicroelectronics STM32 MCUs.
+ USART supports Rx & Tx functionality.
+ It support all industry standard baud rates.
+
+ If unsure, say N.
+
+config SERIAL_STM32_CONSOLE
+ bool "Support for console on STM32"
+ depends on SERIAL_STM32=y
+ select SERIAL_CORE_CONSOLE
+
endmenu
config SERIAL_MCTRL_GPIO
@@ -93,6 +93,7 @@ obj-$(CONFIG_SERIAL_ARC) += arc_uart.o
obj-$(CONFIG_SERIAL_RP2) += rp2.o
obj-$(CONFIG_SERIAL_FSL_LPUART) += fsl_lpuart.o
obj-$(CONFIG_SERIAL_MEN_Z135) += men_z135_uart.o
+obj-$(CONFIG_SERIAL_STM32) += stm32-usart.o
# GPIOLIB helpers for modem control lines
obj-$(CONFIG_SERIAL_MCTRL_GPIO) += serial_mctrl_gpio.o
new file mode 100644
@@ -0,0 +1,695 @@
+/*
+ * Copyright (C) Maxime Coquelin 2015
+ * Author: Maxime Coquelin <mcoquelin.stm32@gmail.com>
+ * License terms: GNU General Public License (GPL), version 2
+ *
+ * Inspired by st-asc.c from STMicroelectronics (c)
+ */
+
+#if defined(CONFIG_SERIAL_STM32_USART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/serial.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/delay.h>
+#include <linux/spinlock.h>
+#include <linux/pm_runtime.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/serial_core.h>
+#include <linux/clk.h>
+
+#define DRIVER_NAME "stm32-usart"
+
+/* Register offsets */
+#define USART_SR 0x00
+#define USART_DR 0x04
+#define USART_BRR 0x08
+#define USART_CR1 0x0c
+#define USART_CR2 0x10
+#define USART_CR3 0x14
+#define USART_GTPR 0x18
+
+/* USART_SR */
+#define USART_SR_PE BIT(0)
+#define USART_SR_FE BIT(1)
+#define USART_SR_NF BIT(2)
+#define USART_SR_ORE BIT(3)
+#define USART_SR_IDLE BIT(4)
+#define USART_SR_RXNE BIT(5)
+#define USART_SR_TC BIT(6)
+#define USART_SR_TXE BIT(7)
+#define USART_SR_LBD BIT(8)
+#define USART_SR_CTS BIT(9)
+#define USART_SR_ERR_MASK (USART_SR_LBD | USART_SR_ORE | \
+ USART_SR_FE | USART_SR_PE)
+/* Dummy bits */
+#define USART_SR_DUMMY_RX BIT(16)
+
+/* USART_DR */
+#define USART_DR_MASK GENMASK(8, 0)
+
+/* USART_BRR */
+#define USART_BRR_DIV_F_MASK GENMASK(3, 0)
+#define USART_BRR_DIV_M_MASK GENMASK(15, 4)
+#define USART_BRR_DIV_M_SHIFT 4
+
+/* USART_CR1 */
+#define USART_CR1_SBK BIT(0)
+#define USART_CR1_RWU BIT(1)
+#define USART_CR1_RE BIT(2)
+#define USART_CR1_TE BIT(3)
+#define USART_CR1_IDLEIE BIT(4)
+#define USART_CR1_RXNEIE BIT(5)
+#define USART_CR1_TCIE BIT(6)
+#define USART_CR1_TXEIE BIT(7)
+#define USART_CR1_PEIE BIT(8)
+#define USART_CR1_PS BIT(9)
+#define USART_CR1_PCE BIT(10)
+#define USART_CR1_WAKE BIT(11)
+#define USART_CR1_M BIT(12)
+#define USART_CR1_UE BIT(13)
+#define USART_CR1_OVER8 BIT(15)
+#define USART_CR1_IE_MASK GENMASK(8, 4)
+
+/* USART_CR2 */
+#define USART_CR2_ADD_MASK GENMASK(3, 0)
+#define USART_CR2_LBDL BIT(5)
+#define USART_CR2_LBDIE BIT(6)
+#define USART_CR2_LBCL BIT(8)
+#define USART_CR2_CPHA BIT(9)
+#define USART_CR2_CPOL BIT(10)
+#define USART_CR2_CLKEN BIT(11)
+#define USART_CR2_STOP_2B BIT(13)
+#define USART_CR2_STOP_MASK GENMASK(13, 12)
+#define USART_CR2_LINEN BIT(14)
+
+/* USART_CR3 */
+#define USART_CR3_EIE BIT(0)
+#define USART_CR3_IREN BIT(1)
+#define USART_CR3_IRLP BIT(2)
+#define USART_CR3_HDSEL BIT(3)
+#define USART_CR3_NACK BIT(4)
+#define USART_CR3_SCEN BIT(5)
+#define USART_CR3_DMAR BIT(6)
+#define USART_CR3_DMAT BIT(7)
+#define USART_CR3_RTSE BIT(8)
+#define USART_CR3_CTSE BIT(9)
+#define USART_CR3_CTSIE BIT(10)
+#define USART_CR3_ONEBIT BIT(11)
+
+/* USART_GTPR */
+#define USART_GTPR_PSC_MASK GENMASK(7, 0)
+#define USART_GTPR_GT_MASK GENMASK(15, 8)
+
+#define DRIVER_NAME "stm32-usart"
+#define STM32_SERIAL_NAME "ttyS"
+#define STM32_MAX_PORTS 6
+
+struct stm32_port {
+ struct uart_port port;
+ struct clk *clk;
+};
+
+static struct stm32_port stm32_ports[STM32_MAX_PORTS];
+static struct uart_driver stm32_usart_driver;
+
+static void stm32_stop_tx(struct uart_port *port);
+
+static void stm32_set_bits(struct uart_port *port, u32 reg, u32 bits)
+{
+ u32 val;
+
+ val = readl_relaxed(port->membase + reg);
+ val |= bits;
+ writel_relaxed(val, port->membase + reg);
+}
+
+static void stm32_clr_bits(struct uart_port *port, u32 reg, u32 bits)
+{
+ u32 val;
+
+ val = readl_relaxed(port->membase + reg);
+ val &= ~bits;
+ writel_relaxed(val, port->membase + reg);
+}
+
+static void stm32_receive_chars(struct uart_port *port)
+{
+ struct tty_port *tport = &port->state->port;
+ unsigned long c;
+ u32 sr;
+ char flag;
+
+ if (port->irq_wake)
+ pm_wakeup_event(tport->tty->dev, 0);
+
+ while ((sr = readl_relaxed(port->membase + USART_SR)) & USART_SR_RXNE) {
+ sr |= USART_SR_DUMMY_RX;
+ c = readl_relaxed(port->membase + USART_DR);
+ flag = TTY_NORMAL;
+ port->icount.rx++;
+
+ if (sr & USART_SR_ERR_MASK) {
+ if (sr & USART_SR_LBD) {
+ port->icount.brk++;
+ if (uart_handle_break(port))
+ continue;
+ } else if (sr & USART_SR_ORE) {
+ port->icount.overrun++;
+ } else if (sr & USART_SR_PE) {
+ port->icount.parity++;
+ } else if (sr & USART_SR_FE) {
+ port->icount.frame++;
+ }
+
+ sr &= port->read_status_mask;
+
+ if (sr & USART_SR_LBD)
+ flag = TTY_BREAK;
+ else if (sr & USART_SR_PE)
+ flag = TTY_PARITY;
+ else if (sr & USART_SR_FE)
+ flag = TTY_FRAME;
+ }
+
+ if (uart_handle_sysrq_char(port, c))
+ continue;
+ uart_insert_char(port, sr, USART_SR_ORE, c, flag);
+ }
+
+ spin_unlock(&port->lock);
+ tty_flip_buffer_push(tport);
+ spin_lock(&port->lock);
+}
+
+static void stm32_transmit_chars(struct uart_port *port)
+{
+ struct circ_buf *xmit = &port->state->xmit;
+
+ if (port->x_char) {
+ writel_relaxed(port->x_char, port->membase + USART_DR);
+ port->x_char = 0;
+ port->icount.tx++;
+ return;
+ }
+
+ if (uart_tx_stopped(port)) {
+ stm32_stop_tx(port);
+ return;
+ }
+
+ if (uart_circ_empty(xmit)) {
+ stm32_stop_tx(port);
+ return;
+ }
+
+ writel_relaxed(xmit->buf[xmit->tail], port->membase + USART_DR);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ port->icount.tx++;
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+
+ if (uart_circ_empty(xmit))
+ stm32_stop_tx(port);
+}
+
+static irqreturn_t stm32_interrupt(int irq, void *ptr)
+{
+ struct uart_port *port = ptr;
+ u32 sr;
+
+ spin_lock(&port->lock);
+
+ sr = readl_relaxed(port->membase + USART_SR);
+
+ if (sr & USART_SR_RXNE)
+ stm32_receive_chars(port);
+
+ if (sr & USART_SR_TXE)
+ stm32_transmit_chars(port);
+
+ spin_unlock(&port->lock);
+
+ return IRQ_HANDLED;
+}
+
+static unsigned int stm32_tx_empty(struct uart_port *port)
+{
+ return readl_relaxed(port->membase + USART_SR) & USART_SR_TXE;
+}
+
+static void stm32_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ /*
+ * This routine is used for seting signals of: DTR, DCD, CTS/RTS
+ * We use USART's hardware for CTS/RTS, so don't need any for that.
+ * Some boards have DTR and DCD implemented using PIO pins,
+ * code to do this should be hooked in here.
+ */
+}
+
+static unsigned int stm32_get_mctrl(struct uart_port *port)
+{
+ /*
+ * This routine is used for geting signals of: DTR, DCD, DSR, RI,
+ * and CTS/RTS
+ */
+ return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
+}
+
+/* There are probably characters waiting to be transmitted. */
+static void stm32_start_tx(struct uart_port *port)
+{
+ struct circ_buf *xmit = &port->state->xmit;
+
+ if (uart_circ_empty(xmit))
+ return;
+
+ stm32_set_bits(port, USART_CR1, USART_CR1_TXEIE | USART_CR1_TE);
+}
+
+/* Transmit stop */
+static void stm32_stop_tx(struct uart_port *port)
+{
+ stm32_clr_bits(port, USART_CR1, USART_CR1_TXEIE);
+}
+
+/* Receive stop */
+static void stm32_stop_rx(struct uart_port *port)
+{
+ stm32_clr_bits(port, USART_CR1, USART_CR1_RXNEIE);
+}
+
+/* Handle breaks - ignored by us */
+static void stm32_break_ctl(struct uart_port *port, int break_state)
+{
+ /* Nothing here yet .. */
+}
+
+static int stm32_startup(struct uart_port *port)
+{
+ const char *name = to_platform_device(port->dev)->name;
+ u32 val;
+
+ if (request_irq(port->irq, stm32_interrupt, IRQF_NO_SUSPEND,
+ name, port)) {
+ dev_err(port->dev, "cannot allocate irq %d\n", port->irq);
+ return -ENODEV;
+ }
+
+ val = USART_CR1_RXNEIE | USART_CR1_TE | USART_CR1_RE;
+ stm32_set_bits(port, USART_CR1, val);
+
+ return 0;
+}
+
+static void stm32_shutdown(struct uart_port *port)
+{
+ u32 val;
+
+ val = USART_CR1_TXEIE | USART_CR1_RXNEIE | USART_CR1_TE | USART_CR1_RE;
+ stm32_set_bits(port, USART_CR1, val);
+
+ free_irq(port->irq, port);
+}
+
+static void stm32_set_termios(struct uart_port *port, struct ktermios *termios,
+ struct ktermios *old)
+{
+ unsigned int baud;
+ u32 usardiv, mantissa, fraction;
+ tcflag_t cflag;
+ u32 cr1, cr2, cr3;
+ unsigned long flags;
+
+ baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
+ cflag = termios->c_cflag;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ /* Stop serial port and reset value */
+ writel_relaxed(0, port->membase + USART_CR1);
+
+ cr1 = USART_CR1_TE | USART_CR1_RE | USART_CR1_UE | USART_CR1_RXNEIE;
+
+ if (cflag & CSTOPB)
+ cr2 = USART_CR2_STOP_2B;
+
+ if (cflag & PARENB) {
+ cr1 |= USART_CR1_PCE;
+ if ((cflag & CSIZE) == CS8)
+ cr1 |= USART_CR1_M;
+ }
+
+ if (cflag & PARODD)
+ cr1 |= USART_CR1_PS;
+
+ if (cflag & CRTSCTS)
+ cr3 = USART_CR3_RTSE | USART_CR3_CTSE;
+
+ usardiv = (port->uartclk * 25) / (baud * 4);
+ mantissa = (usardiv / 100) << USART_BRR_DIV_M_SHIFT;
+ fraction = DIV_ROUND_CLOSEST((usardiv % 100) * 16, 100);
+ if (fraction & ~USART_BRR_DIV_F_MASK) {
+ fraction = 0;
+ mantissa += (1 << USART_BRR_DIV_M_SHIFT);
+ }
+
+ writel_relaxed(mantissa | fraction, port->membase + USART_BRR);
+
+ uart_update_timeout(port, cflag, baud);
+
+ port->read_status_mask = USART_SR_ORE;
+ if (termios->c_iflag & INPCK)
+ port->read_status_mask |= USART_SR_PE | USART_SR_FE;
+ if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
+ port->read_status_mask |= USART_SR_LBD;
+
+ /* Characters to ignore */
+ port->ignore_status_mask = 0;
+ if (termios->c_iflag & IGNPAR)
+ port->ignore_status_mask = USART_SR_PE | USART_SR_FE;
+ if (termios->c_iflag & IGNBRK) {
+ port->ignore_status_mask |= USART_SR_LBD;
+ /*
+ * If we're ignoring parity and break indicators,
+ * ignore overruns too (for real raw support).
+ */
+ if (termios->c_iflag & IGNPAR)
+ port->ignore_status_mask |= USART_SR_ORE;
+ }
+
+ /*
+ * Ignore all characters if CREAD is not set.
+ */
+ if ((termios->c_cflag & CREAD) == 0)
+ port->ignore_status_mask |= USART_SR_DUMMY_RX;
+
+ writel_relaxed(cr3, port->membase + USART_CR3);
+ writel_relaxed(cr2, port->membase + USART_CR2);
+ writel_relaxed(cr1, port->membase + USART_CR1);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *stm32_type(struct uart_port *port)
+{
+ return (port->type == PORT_STM32) ? DRIVER_NAME : NULL;
+}
+
+static void stm32_release_port(struct uart_port *port)
+{
+}
+
+static int stm32_request_port(struct uart_port *port)
+{
+ return 0;
+}
+
+static void stm32_config_port(struct uart_port *port, int flags)
+{
+ if ((flags & UART_CONFIG_TYPE))
+ port->type = PORT_STM32;
+}
+
+static int
+stm32_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+ /* No user changeable parameters */
+ return -EINVAL;
+}
+
+static void stm32_pm(struct uart_port *port, unsigned int state,
+ unsigned int oldstate)
+{
+ struct stm32_port *stm32port = container_of(port,
+ struct stm32_port, port);
+ unsigned long flags = 0;
+
+ switch (state) {
+ case UART_PM_STATE_ON:
+ clk_prepare_enable(stm32port->clk);
+ break;
+ case UART_PM_STATE_OFF:
+ spin_lock_irqsave(&port->lock, flags);
+ stm32_clr_bits(port, USART_CR1, USART_CR1_UE);
+ spin_unlock_irqrestore(&port->lock, flags);
+ clk_disable_unprepare(stm32port->clk);
+ break;
+ }
+}
+
+static struct uart_ops stm32_uart_ops = {
+ .tx_empty = stm32_tx_empty,
+ .set_mctrl = stm32_set_mctrl,
+ .get_mctrl = stm32_get_mctrl,
+ .start_tx = stm32_start_tx,
+ .stop_tx = stm32_stop_tx,
+ .stop_rx = stm32_stop_rx,
+ .break_ctl = stm32_break_ctl,
+ .startup = stm32_startup,
+ .shutdown = stm32_shutdown,
+ .set_termios = stm32_set_termios,
+ .type = stm32_type,
+ .release_port = stm32_release_port,
+ .request_port = stm32_request_port,
+ .config_port = stm32_config_port,
+ .verify_port = stm32_verify_port,
+ .pm = stm32_pm,
+};
+
+static int stm32_init_port(struct stm32_port *stm32port,
+ struct platform_device *pdev)
+{
+ struct uart_port *port = &stm32port->port;
+ struct resource *res;
+
+ port->iotype = UPIO_MEM;
+ port->flags = UPF_BOOT_AUTOCONF;
+ port->ops = &stm32_uart_ops;
+ port->dev = &pdev->dev;
+ port->irq = platform_get_irq(pdev, 0);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ port->membase = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(port->membase))
+ return PTR_ERR(port->membase);
+ port->mapbase = res->start;
+
+ spin_lock_init(&port->lock);
+
+ stm32port->clk = devm_clk_get(&pdev->dev, NULL);
+
+ if (WARN_ON(IS_ERR(stm32port->clk)))
+ return -EINVAL;
+
+ /* ensure that clk rate is correct by enabling the clk */
+ clk_prepare_enable(stm32port->clk);
+ stm32port->port.uartclk = clk_get_rate(stm32port->clk);
+ WARN_ON(stm32port->port.uartclk == 0);
+ clk_disable_unprepare(stm32port->clk);
+
+ return 0;
+}
+
+static struct stm32_port *stm32_of_get_stm32_port(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ int id;
+
+ if (!np)
+ return NULL;
+
+ id = of_alias_get_id(np, STM32_SERIAL_NAME);
+
+ if (id < 0)
+ id = 0;
+
+ if (WARN_ON(id >= STM32_MAX_PORTS))
+ return NULL;
+
+ stm32_ports[id].port.line = id;
+ return &stm32_ports[id];
+}
+
+#ifdef CONFIG_OF
+static struct of_device_id stm32_match[] = {
+ { .compatible = "st,stm32-usart", },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, stm32_match);
+#endif
+
+static int stm32_serial_probe(struct platform_device *pdev)
+{
+ int ret;
+ struct stm32_port *stm32port;
+
+ stm32port = stm32_of_get_stm32_port(pdev);
+ if (!stm32port)
+ return -ENODEV;
+
+ ret = stm32_init_port(stm32port, pdev);
+ if (ret)
+ return ret;
+
+ ret = uart_add_one_port(&stm32_usart_driver, &stm32port->port);
+ if (ret)
+ return ret;
+
+ platform_set_drvdata(pdev, &stm32port->port);
+
+ return 0;
+}
+
+static int stm32_serial_remove(struct platform_device *pdev)
+{
+ struct uart_port *port = platform_get_drvdata(pdev);
+
+ return uart_remove_one_port(&stm32_usart_driver, port);
+}
+
+
+#ifdef CONFIG_SERIAL_STM32_CONSOLE
+static void stm32_console_putchar(struct uart_port *port, int ch)
+{
+ while (!(readl_relaxed(port->membase + USART_SR) & USART_SR_TXE))
+ cpu_relax();
+
+ writel_relaxed(ch, port->membase + USART_DR);
+}
+
+static void stm32_console_write(struct console *co, const char *s, unsigned cnt)
+{
+ struct uart_port *port = &stm32_ports[co->index].port;
+ unsigned long flags;
+ u32 old_cr1, new_cr1;
+ int locked = 1;
+
+ if (oops_in_progress) {
+ locked = spin_trylock_irqsave(&port->lock, flags);
+ } else {
+ locked = 1;
+ spin_lock_irqsave(&port->lock, flags);
+ }
+
+ /* Save and disable interrupts */
+ old_cr1 = readl_relaxed(port->membase + USART_CR1);
+ new_cr1 = old_cr1 & ~USART_CR1_IE_MASK;
+ writel_relaxed(new_cr1, port->membase + USART_CR1);
+
+ uart_console_write(port, s, cnt, stm32_console_putchar);
+
+ /* Restore interrupt state */
+ writel_relaxed(old_cr1, port->membase + USART_CR1);
+
+ if (locked)
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static int stm32_console_setup(struct console *co, char *options)
+{
+ struct stm32_port *stm32port;
+ int baud = 9600;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ if (co->index >= STM32_MAX_PORTS)
+ return -ENODEV;
+
+ stm32port = &stm32_ports[co->index];
+
+ /*
+ * This driver does not support early console initialization
+ * (use ARM early printk support instead), so we only expect
+ * this to be called during the uart port registration when the
+ * driver gets probed and the port should be mapped at that point.
+ */
+ if (stm32port->port.mapbase == 0 || stm32port->port.membase == NULL)
+ return -ENXIO;
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+ return uart_set_options(&stm32port->port, co, baud, parity, bits, flow);
+}
+
+static struct console stm32_console = {
+ .name = STM32_SERIAL_NAME,
+ .device = uart_console_device,
+ .write = stm32_console_write,
+ .setup = stm32_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &stm32_usart_driver,
+};
+
+#define STM32_SERIAL_CONSOLE (&stm32_console)
+
+#else
+#define STM32_SERIAL_CONSOLE NULL
+#endif /* CONFIG_SERIAL_STM32_CONSOLE */
+
+static struct uart_driver stm32_usart_driver = {
+ .owner = THIS_MODULE,
+ .driver_name = DRIVER_NAME,
+ .dev_name = STM32_SERIAL_NAME,
+ .major = 0,
+ .minor = 0,
+ .nr = STM32_MAX_PORTS,
+ .cons = STM32_SERIAL_CONSOLE,
+};
+
+static struct platform_driver stm32_serial_driver = {
+ .probe = stm32_serial_probe,
+ .remove = stm32_serial_remove,
+ .driver = {
+ .name = DRIVER_NAME,
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(stm32_match),
+ },
+};
+
+static int __init usart_init(void)
+{
+ int ret;
+ static char banner[] __initdata =
+ KERN_INFO "STM32 USART driver initialized\n";
+
+ printk(banner);
+
+ ret = uart_register_driver(&stm32_usart_driver);
+ if (ret)
+ return ret;
+
+ ret = platform_driver_register(&stm32_serial_driver);
+ if (ret)
+ uart_unregister_driver(&stm32_usart_driver);
+
+ return ret;
+}
+
+static void __exit usart_exit(void)
+{
+ platform_driver_unregister(&stm32_serial_driver);
+ uart_unregister_driver(&stm32_usart_driver);
+}
+
+module_init(usart_init);
+module_exit(usart_exit);
+
+MODULE_ALIAS("platform:" DRIVER_NAME);
+MODULE_DESCRIPTION("STMicroelectronics STM32 serial port driver");
+MODULE_LICENSE("GPL");
@@ -248,4 +248,7 @@
/* MESON */
#define PORT_MESON 109
+/* STM32 USART */
+#define PORT_STM32 110
+
#endif /* _UAPILINUX_SERIAL_CORE_H */
This drivers adds support to the STM32 USART controller, which is a standard serial driver. Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com> --- .../devicetree/bindings/serial/st,stm32-usart.txt | 18 + drivers/tty/serial/Kconfig | 17 + drivers/tty/serial/Makefile | 1 + drivers/tty/serial/stm32-usart.c | 695 +++++++++++++++++++++ include/uapi/linux/serial_core.h | 3 + 5 files changed, 734 insertions(+) create mode 100644 Documentation/devicetree/bindings/serial/st,stm32-usart.txt create mode 100644 drivers/tty/serial/stm32-usart.c