@@ -391,6 +391,10 @@ dlan-pro-1200-ac)
gl-ar300m)
ucidef_set_led_wlan "wlan" "WLAN" "$board:red:wlan" "phy0tpt"
;;
+gl-ar750)
+ ucidef_set_led_wlan "wlan-2g" "WLAN-2G" "gl-ar750:wlan-2g" "phy1tpt"
+ ucidef_set_led_wlan "wlan-5g" "WLAN-5G" "gl-ar750:wlan-5g" "phy0tpt"
+ ;;
gl-mifi)
ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt"
ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth0"
@@ -145,6 +145,7 @@ ar71xx_setup_interfaces()
dr344|\
gl-ar150|\
gl-ar300m|\
+ gl-ar750|\
gl-domino|\
gl-inet|\
gl-mifi|\
old mode 100644
new mode 100755
@@ -75,7 +75,7 @@ get_status_led() {
ap90q|\
cpe830|\
cpe870|\
- gl-ar300m|\
+ gl-ar300m|\
gl-inet|\
gl-mifi)
status_led="$board:green:lan"
@@ -521,6 +521,7 @@ set_state() {
done)
status_led_on
case $(board_name) in
+ gl-ar750|\
gl-ar300m)
fw_printenv lc >/dev/null 2>&1 && fw_setenv "bootcount" 0
;;
old mode 100644
new mode 100755
@@ -81,6 +81,10 @@ case "$FIRMWARE" in
ath10kcal_extract "art" 20480 2116
ath10kcal_patch_mac $(mtd_get_mac_binary art 18)
;;
+ gl-ar750)
+ ath10kcal_extract "art" 20480 2116
+ ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0) +1)
+ ;;
epg5000|\
esr1750)
ath10kcal_extract "caldata" 20480 2116
@@ -670,6 +670,9 @@ ar71xx_board_detect() {
*"GL-AR300M")
name="gl-ar300m"
;;
+ *"GL-AR750")
+ name="gl-ar750"
+ ;;
*"GL-CONNECT INET v1")
name="gl-inet"
@@ -249,6 +249,7 @@ platform_check_image() {
ew-dorin|\
ew-dorin-router|\
gl-ar150|\
+ gl-ar750|\
gl-ar300m|\
gl-ar300|\
gl-domino|\
old mode 100644
new mode 100755
@@ -115,6 +115,7 @@ CONFIG_ATH79_MACH_FRITZ300E=y
CONFIG_ATH79_MACH_GL_AR150=y
CONFIG_ATH79_MACH_GL_AR300=y
CONFIG_ATH79_MACH_GL_AR300M=y
+CONFIG_ATH79_MACH_GL_AR750=y
CONFIG_ATH79_MACH_GL_DOMINO=y
CONFIG_ATH79_MACH_GL_INET=y
CONFIG_ATH79_MACH_GL_MIFI=y
old mode 100644
new mode 100755
@@ -761,6 +761,16 @@ config ATH79_MACH_GL_AR300M
select ATH79_DEV_USB
select ATH79_DEV_WMAC
+config ATH79_MACH_GL_AR750
+ bool "GL_AR750 support"
+ select SOC_QCA953X
+ select ATH79_DEV_ETH
+ select ATH79_DEV_GPIO_BUTTONS
+ select ATH79_DEV_LEDS_GPIO
+ select ATH79_DEV_M25P80
+ select ATH79_DEV_USB
+ select ATH79_DEV_WMAC
+
config ATH79_MACH_GL_DOMINO
bool "DOMINO support"
select SOC_AR933X
old mode 100644
new mode 100755
@@ -121,6 +121,7 @@ obj-$(CONFIG_ATH79_MACH_FRITZ300E) += mach-fritz300e.o
obj-$(CONFIG_ATH79_MACH_GL_AR150) += mach-gl-ar150.o
obj-$(CONFIG_ATH79_MACH_GL_AR300) += mach-gl-ar300.o
obj-$(CONFIG_ATH79_MACH_GL_AR300M) += mach-gl-ar300m.o
+obj-$(CONFIG_ATH79_MACH_GL_AR750) += mach-gl-ar750.o
obj-$(CONFIG_ATH79_MACH_GL_DOMINO) += mach-gl-domino.o
obj-$(CONFIG_ATH79_MACH_GL_INET) += mach-gl-inet.o
obj-$(CONFIG_ATH79_MACH_GL_MIFI) += mach-gl-mifi.o
new file mode 100755
@@ -0,0 +1,187 @@
+/*
+ * GLI AR750 board support
+ *
+ * Copyright (C) 2011 dongyuqi <729650915@qq.com>
+ * Copyright (C) 2011-2012 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (C) 2013 alzhao <alzhao@gmail.com>
+ * Copyright (C) 2014 Michel Stempin <michel.stempin@wanadoo.fr>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/gpio.h>
+#include <linux/pci.h>
+
+#include <asm/mach-ath79/ath79.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+#include <linux/i2c.h>
+#include <linux/i2c-gpio.h>
+#include <linux/platform_device.h>
+
+#include "common.h"
+#include "dev-ap9x-pci.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-usb.h"
+#include "dev-spi.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+#include "pci.h"
+
+#define GL_AR750_GPIO_LED_USB 2
+#define GL_AR750_GPIO_LED_WLAN 13
+#define GL_AR750_GPIO_LED_LAN 14
+#define GL_AR750_GPIO_LED_SYSTEM 12
+#define GL_AR750_GPIO_BTN_RESET 3
+#define GL_AR750_GPIO_BTN_LEFT 0
+#define GL_AR750_GPIO_BTN_RIGHT 1
+
+#define GL_AR750_GPIO_I2C_SCL 16
+#define GL_AR750_GPIO_I2C_SDA 17
+
+#define GL_AR750_KEYS_POLL_INTERVAL 20 /* msecs */
+#define GL_AR750_KEYS_DEBOUNCE_INTERVAL (3 * GL_AR750_KEYS_POLL_INTERVAL)
+
+#define GL_AR750_MAC0_OFFSET 0
+#define GL_AR750_MAC1_OFFSET 6
+#define GL_AR750_WMAC_CALDATA_OFFSET 0x1000
+#define GL_AR750_PCIE_CALDATA_OFFSET 0x5000
+
+static struct gpio_led gl_ar750_leds_gpio[] __initdata = {
+ {
+ .name = "gl-ar750:usbpow",
+ .gpio = GL_AR750_GPIO_LED_USB,
+ .active_low = 0,
+ .default_state = 1,
+ },
+ {
+ .name = "gl-ar750:wlan-2g",
+ .gpio = GL_AR750_GPIO_LED_LAN,
+ .active_low = 1,
+ },
+ {
+ .name = "gl-ar750:wlan-5g",
+ .gpio = GL_AR750_GPIO_LED_WLAN,
+ .active_low = 1,
+ },
+ {
+ .name = "gl-ar750:system",
+ .gpio = GL_AR750_GPIO_LED_SYSTEM,
+ .active_low = 1,
+ .default_state = 1,
+ },
+};
+
+static struct gpio_keys_button gl_ar750_gpio_keys[] __initdata = {
+ {
+ .desc = "reset",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = GL_AR750_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = GL_AR750_GPIO_BTN_RESET,
+ .active_low = 1,
+ },
+ {
+ .desc = "button right",
+ .type = EV_KEY,
+ .code = BTN_0,
+ .debounce_interval = GL_AR750_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = GL_AR750_GPIO_BTN_LEFT,
+ .active_low = 0,
+ },
+ {
+ .desc = "button left",
+ .type = EV_KEY,
+ .code = BTN_1,
+ .debounce_interval = GL_AR750_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = GL_AR750_GPIO_BTN_RIGHT,
+ .active_low = 0,
+ },
+};
+
+static struct spi_board_info gl_ar750_spi_info[] = {
+ {
+ .bus_num = 0,
+ .chip_select = 0,
+ .max_speed_hz = 25000000,
+ .modalias = "m25p80",
+ .platform_data = NULL,
+ },
+ {
+ .bus_num = 0,
+ .chip_select = 1,
+ .max_speed_hz = 25000000,
+ .modalias = "ath79-spinand",
+ .platform_data = NULL,
+ }
+};
+
+static struct ath79_spi_platform_data gl_ar750_spi_data = {
+ .bus_num = 0,
+ .num_chipselect = 2,
+};
+
+static struct i2c_gpio_platform_data gl_ar750_i2c_gpio_data = {
+ .sda_pin = GL_AR750_GPIO_I2C_SDA,
+ .scl_pin = GL_AR750_GPIO_I2C_SCL,
+};
+
+static struct platform_device gl_ar750_i2c_gpio_device = {
+ .name = "i2c-gpio",
+ .id = 0,
+ .dev = {
+ .platform_data = &gl_ar750_i2c_gpio_data,
+ }
+};
+
+
+static void __init gl_ar750_setup(void)
+{
+ u8 *art = (u8 *) KSEG1ADDR(0x1f050000);
+ u8 tmpmac[ETH_ALEN];
+
+ ath79_gpio_function_enable(AR934X_GPIO_FUNC_JTAG_DISABLE);
+ ath79_register_spi(&gl_ar750_spi_data, gl_ar750_spi_info, 2);
+
+ /* register gpio LEDs and keys */
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(gl_ar750_leds_gpio),
+ gl_ar750_leds_gpio);
+ ath79_register_gpio_keys_polled(-1, GL_AR750_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(gl_ar750_gpio_keys),
+ gl_ar750_gpio_keys);
+
+ ath79_register_mdio(0, 0x0);
+
+ /* WAN */
+ ath79_init_mac(ath79_eth0_data.mac_addr, art + GL_AR750_MAC0_OFFSET, 0);
+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
+ ath79_eth0_data.speed = SPEED_100;
+ ath79_eth0_data.duplex = DUPLEX_FULL;
+ ath79_eth0_data.phy_mask = BIT(4);
+ ath79_register_eth(0);
+
+ /* LAN */
+ ath79_init_mac(ath79_eth1_data.mac_addr, art + GL_AR750_MAC0_OFFSET, 1);
+ ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII;
+ ath79_eth1_data.speed = SPEED_1000;
+ ath79_eth1_data.duplex = DUPLEX_FULL;
+ ath79_switch_data.phy_poll_mask |= BIT(4);
+ ath79_switch_data.phy4_mii_en = 1;
+ ath79_register_eth(1);
+
+ ath79_init_mac(tmpmac, art + GL_AR750_WMAC_CALDATA_OFFSET + 2, 0);
+ ath79_register_wmac(art + GL_AR750_WMAC_CALDATA_OFFSET, tmpmac);
+ /*register i2c*/
+ platform_device_register(&gl_ar750_i2c_gpio_device);
+ /* enable usb */
+ ath79_register_usb();
+ /* enable pci */
+ ath79_register_pci();
+}
+
+MIPS_MACHINE(ATH79_MACH_GL_AR750, "GL-AR750", "GL-AR750",
+ gl_ar750_setup);
old mode 100644
new mode 100755
@@ -113,6 +113,7 @@ enum ath79_mach_type {
ATH79_MACH_GL_AR150, /* GL-AR150 support */
ATH79_MACH_GL_AR300, /* GL-AR300 */
ATH79_MACH_GL_AR300M, /* GL-AR300M */
+ ATH79_MACH_GL_AR750, /* GL-AR750 */
ATH79_MACH_GL_DOMINO, /* Domino */
ATH79_MACH_GL_INET, /* GL-CONNECT GL-INET */
ATH79_MACH_GL_MIFI, /* GL-MIFI support */
old mode 100644
new mode 100755
@@ -287,6 +287,16 @@ define Device/gl-ar300m
endef
TARGET_DEVICES += gl-ar300m
+define Device/gl-ar750
+ DEVICE_TITLE := GL.iNet GL-AR750
+ DEVICE_PACKAGES := kmod-usb-core kmod-usb2 uboot-envtools
+ BOARDNAME = GL-AR750
+ IMAGE_SIZE = 16000k
+ CONSOLE = ttyS0,115200
+ MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(art)ro,16000k(firmware)
+endef
+TARGET_DEVICES += gl-ar750
+
define Device/gl-domino
DEVICE_TITLE := GL.iNet Domino Pi
DEVICE_PACKAGES := kmod-usb-core kmod-usb2