diff mbox series

[iwl-net,v1,2/4] igc: Fix reset adapter logics when tx mode change

Message ID 20240702040926.3327530-3-faizal.abdul.rahim@linux.intel.com
State Changes Requested
Headers show
Series igc bug fixes related to qbv_count usage | expand

Commit Message

Abdul Rahim, Faizal July 2, 2024, 4:09 a.m. UTC
Following the "igc: Fix TX Hang issue when QBV Gate is close" changes,
remaining issues with the reset adapter logic in igc_tsn_offload_apply()
have been observed:

1. The reset adapter logics for i225 and i226 differ, although they should
   be the same according to the guidelines in I225/6 HW Design Section
   7.5.2.1 on software initialization during tx mode changes.
2. The i225 resets adapter every time, even though tx mode doesn't change.
   This occurs solely based on the condition  igc_is_device_id_i225() when
   calling schedule_work().
3. i226 doesn't reset adapter for tsn->legacy tx mode changes. It only
   resets adapter for legacy->tsn tx mode transitions.
4. qbv_count introduced in the patch is actually not needed; in this
   context, a non-zero value of qbv_count is used to indicate if tx mode
   was unconditionally set to tsn in igc_tsn_enable_offload(). This could
   be replaced by checking the existing register
   IGC_TQAVCTRL_TRANSMIT_MODE_TSN bit.

This patch resolves all issues and enters schedule_work() to reset the
adapter only when changing tx mode. It also removes reliance on qbv_count.

qbv_count field will be removed in a future patch.

Test ran:

1. Verify reset adapter behaviour in i225/6:
   a) Enrol a new GCL
      Reset adapter observed (tx mode change legacy->tsn)
   b) Enrol a new GCL without deleting qdisc
      No reset adapter observed (tx mode remain tsn->tsn)
   c) Delete qdisc
      Reset adapter observed (tx mode change tsn->legacy)

2. Tested scenario from "igc: Fix TX Hang issue when QBV Gate is closed"
   to confirm it remains resolved.

Fixes: 175c241288c0 ("igc: Fix TX Hang issue when QBV Gate is closed")
Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
---
 drivers/net/ethernet/intel/igc/igc_tsn.c | 26 +++++++++++++++++++++---
 1 file changed, 23 insertions(+), 3 deletions(-)

Comments

Simon Horman July 3, 2024, 3:03 p.m. UTC | #1
On Tue, Jul 02, 2024 at 12:09:24AM -0400, Faizal Rahim wrote:
> Following the "igc: Fix TX Hang issue when QBV Gate is close" changes,
> remaining issues with the reset adapter logic in igc_tsn_offload_apply()
> have been observed:
> 
> 1. The reset adapter logics for i225 and i226 differ, although they should
>    be the same according to the guidelines in I225/6 HW Design Section
>    7.5.2.1 on software initialization during tx mode changes.
> 2. The i225 resets adapter every time, even though tx mode doesn't change.
>    This occurs solely based on the condition  igc_is_device_id_i225() when
>    calling schedule_work().
> 3. i226 doesn't reset adapter for tsn->legacy tx mode changes. It only
>    resets adapter for legacy->tsn tx mode transitions.
> 4. qbv_count introduced in the patch is actually not needed; in this
>    context, a non-zero value of qbv_count is used to indicate if tx mode
>    was unconditionally set to tsn in igc_tsn_enable_offload(). This could
>    be replaced by checking the existing register
>    IGC_TQAVCTRL_TRANSMIT_MODE_TSN bit.
> 
> This patch resolves all issues and enters schedule_work() to reset the
> adapter only when changing tx mode. It also removes reliance on qbv_count.
> 
> qbv_count field will be removed in a future patch.
> 
> Test ran:
> 
> 1. Verify reset adapter behaviour in i225/6:
>    a) Enrol a new GCL
>       Reset adapter observed (tx mode change legacy->tsn)
>    b) Enrol a new GCL without deleting qdisc
>       No reset adapter observed (tx mode remain tsn->tsn)
>    c) Delete qdisc
>       Reset adapter observed (tx mode change tsn->legacy)
> 
> 2. Tested scenario from "igc: Fix TX Hang issue when QBV Gate is closed"
>    to confirm it remains resolved.
> 
> Fixes: 175c241288c0 ("igc: Fix TX Hang issue when QBV Gate is closed")
> Signed-off-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>

Hi Faizal,

Nits below not withstahdning, this looks good to me.

Reviewed-by: Simon Horman <horms@kernel.org>

> ---
>  drivers/net/ethernet/intel/igc/igc_tsn.c | 26 +++++++++++++++++++++---
>  1 file changed, 23 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/net/ethernet/intel/igc/igc_tsn.c b/drivers/net/ethernet/intel/igc/igc_tsn.c
> index 02dd41aff634..61f047ebf34d 100644
> --- a/drivers/net/ethernet/intel/igc/igc_tsn.c
> +++ b/drivers/net/ethernet/intel/igc/igc_tsn.c
> @@ -49,6 +49,13 @@ static unsigned int igc_tsn_new_flags(struct igc_adapter *adapter)
>  	return new_flags;
>  }
>  
> +static bool igc_tsn_is_tx_mode_in_tsn(struct igc_adapter *adapter)
> +{
> +	struct igc_hw *hw = &adapter->hw;
> +
> +	return (bool)(rd32(IGC_TQAVCTRL) & IGC_TQAVCTRL_TRANSMIT_MODE_TSN);

Perhaps it is more a question of taste than anything else.
But my preference, FIIW, is to avoid casts.
And I think in this case using !! is a common pattern.

(Completely untested!)

	return !!(rd32(IGC_TQAVCTRL) & IGC_TQAVCTRL_TRANSMIT_MODE_TSN);

> +}
> +
>  void igc_tsn_adjust_txtime_offset(struct igc_adapter *adapter)
>  {
>  	struct igc_hw *hw = &adapter->hw;
> @@ -334,15 +341,28 @@ int igc_tsn_reset(struct igc_adapter *adapter)
>  	return err;
>  }
>  
> +static bool igc_tsn_will_tx_mode_change(struct igc_adapter *adapter)
> +{
> +	bool any_tsn_enabled = (bool)(igc_tsn_new_flags(adapter) &
> +			       IGC_FLAG_TSN_ANY_ENABLED);

Ditto.

> +
> +	if ((any_tsn_enabled && !igc_tsn_is_tx_mode_in_tsn(adapter)) ||
> +	    (!any_tsn_enabled && igc_tsn_is_tx_mode_in_tsn(adapter)))
> +		return true;
> +	else
> +		return false;

Likewise, this is probably more a matter of taste than anything else.
But I think this could be expressed as:

(Completely untested!)

	return (any_tsn_enabled && !igc_tsn_is_tx_mode_in_tsn(adapter)) ||
		(!any_tsn_enabled && igc_tsn_is_tx_mode_in_tsn(adapter));

Similarly in the previous patch of this series.

> +}
> +
>  int igc_tsn_offload_apply(struct igc_adapter *adapter)
>  {
>  	struct igc_hw *hw = &adapter->hw;
>  
> -	/* Per I225/6 HW Design Section 7.5.2.1, transmit mode
> -	 * cannot be changed dynamically. Require reset the adapter.
> +	/* Per I225/6 HW Design Section 7.5.2.1 guideline, if tx mode change
> +	 * from legacy->tsn or tsn->legacy, then reset adapter is needed.
>  	 */
>  	if (netif_running(adapter->netdev) &&
> -	    (igc_is_device_id_i225(hw) || !adapter->qbv_count)) {
> +	    (igc_is_device_id_i225(hw) || igc_is_device_id_i226(hw)) &&
> +	     igc_tsn_will_tx_mode_change(adapter)) {
>  		schedule_work(&adapter->reset_task);
>  		return 0;
>  	}
> -- 
> 2.25.1
> 
>
Abdul Rahim, Faizal July 5, 2024, 4:52 p.m. UTC | #2
>> ---
>>   drivers/net/ethernet/intel/igc/igc_tsn.c | 26 +++++++++++++++++++++---
>>   1 file changed, 23 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/net/ethernet/intel/igc/igc_tsn.c b/drivers/net/ethernet/intel/igc/igc_tsn.c
>> index 02dd41aff634..61f047ebf34d 100644
>> --- a/drivers/net/ethernet/intel/igc/igc_tsn.c
>> +++ b/drivers/net/ethernet/intel/igc/igc_tsn.c
>> @@ -49,6 +49,13 @@ static unsigned int igc_tsn_new_flags(struct igc_adapter *adapter)
>>   	return new_flags;
>>   }
>>   
>> +static bool igc_tsn_is_tx_mode_in_tsn(struct igc_adapter *adapter)
>> +{
>> +	struct igc_hw *hw = &adapter->hw;
>> +
>> +	return (bool)(rd32(IGC_TQAVCTRL) & IGC_TQAVCTRL_TRANSMIT_MODE_TSN);
> 
> Perhaps it is more a question of taste than anything else.
> But my preference, FIIW, is to avoid casts.
> And I think in this case using !! is a common pattern.
> 
> (Completely untested!)
> 
> 	return !!(rd32(IGC_TQAVCTRL) & IGC_TQAVCTRL_TRANSMIT_MODE_TSN);
> 

Sure, will update.

>> +
>> +	if ((any_tsn_enabled && !igc_tsn_is_tx_mode_in_tsn(adapter)) ||
>> +	    (!any_tsn_enabled && igc_tsn_is_tx_mode_in_tsn(adapter)))
>> +		return true;
>> +	else
>> +		return false;
> 
> Likewise, this is probably more a matter of taste than anything else.
> But I think this could be expressed as:
> 
> (Completely untested!)
> 
> 	return (any_tsn_enabled && !igc_tsn_is_tx_mode_in_tsn(adapter)) ||
> 		(!any_tsn_enabled && igc_tsn_is_tx_mode_in_tsn(adapter));
> 
> Similarly in the previous patch of this series.
> 

Will update, your suggestion is better, lesser parenthesis.
Thanks.
diff mbox series

Patch

diff --git a/drivers/net/ethernet/intel/igc/igc_tsn.c b/drivers/net/ethernet/intel/igc/igc_tsn.c
index 02dd41aff634..61f047ebf34d 100644
--- a/drivers/net/ethernet/intel/igc/igc_tsn.c
+++ b/drivers/net/ethernet/intel/igc/igc_tsn.c
@@ -49,6 +49,13 @@  static unsigned int igc_tsn_new_flags(struct igc_adapter *adapter)
 	return new_flags;
 }
 
+static bool igc_tsn_is_tx_mode_in_tsn(struct igc_adapter *adapter)
+{
+	struct igc_hw *hw = &adapter->hw;
+
+	return (bool)(rd32(IGC_TQAVCTRL) & IGC_TQAVCTRL_TRANSMIT_MODE_TSN);
+}
+
 void igc_tsn_adjust_txtime_offset(struct igc_adapter *adapter)
 {
 	struct igc_hw *hw = &adapter->hw;
@@ -334,15 +341,28 @@  int igc_tsn_reset(struct igc_adapter *adapter)
 	return err;
 }
 
+static bool igc_tsn_will_tx_mode_change(struct igc_adapter *adapter)
+{
+	bool any_tsn_enabled = (bool)(igc_tsn_new_flags(adapter) &
+			       IGC_FLAG_TSN_ANY_ENABLED);
+
+	if ((any_tsn_enabled && !igc_tsn_is_tx_mode_in_tsn(adapter)) ||
+	    (!any_tsn_enabled && igc_tsn_is_tx_mode_in_tsn(adapter)))
+		return true;
+	else
+		return false;
+}
+
 int igc_tsn_offload_apply(struct igc_adapter *adapter)
 {
 	struct igc_hw *hw = &adapter->hw;
 
-	/* Per I225/6 HW Design Section 7.5.2.1, transmit mode
-	 * cannot be changed dynamically. Require reset the adapter.
+	/* Per I225/6 HW Design Section 7.5.2.1 guideline, if tx mode change
+	 * from legacy->tsn or tsn->legacy, then reset adapter is needed.
 	 */
 	if (netif_running(adapter->netdev) &&
-	    (igc_is_device_id_i225(hw) || !adapter->qbv_count)) {
+	    (igc_is_device_id_i225(hw) || igc_is_device_id_i226(hw)) &&
+	     igc_tsn_will_tx_mode_change(adapter)) {
 		schedule_work(&adapter->reset_task);
 		return 0;
 	}