@@ -1516,65 +1516,35 @@ static s32 ixgbe_init_ext_t_x550em(struct ixgbe_hw *hw)
{
s32 status;
u16 reg;
- u32 retries = 2;
- do {
- /* decrement retries counter and exit if we hit 0 */
- if (retries < 1) {
- hw_dbg(hw, "External PHY not yet finished resetting.");
- return IXGBE_ERR_PHY;
- }
- retries--;
-
- status = hw->phy.ops.read_reg(hw,
- IXGBE_MDIO_TX_VENDOR_ALARMS_3,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE,
- ®);
- if (status)
- return status;
-
- /* Verify PHY FW reset has completed */
- } while ((reg & IXGBE_MDIO_TX_VENDOR_ALARMS_3_RST_MASK) != 1);
-
- /* Set port to low power mode */
- status = hw->phy.ops.read_reg(hw,
- IXGBE_MDIO_VENDOR_SPECIFIC_1_CONTROL,
- IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
- ®);
- if (status)
- return status;
-
- /* Enable the transmitter */
status = hw->phy.ops.read_reg(hw,
- IXGBE_MDIO_PMD_STD_TX_DISABLE_CNTR,
+ IXGBE_MDIO_TX_VENDOR_ALARMS_3,
IXGBE_MDIO_PMA_PMD_DEV_TYPE,
®);
if (status)
return status;
- reg &= ~IXGBE_MDIO_PMD_GLOBAL_TX_DISABLE;
-
- status = hw->phy.ops.write_reg(hw,
- IXGBE_MDIO_PMD_STD_TX_DISABLE_CNTR,
- IXGBE_MDIO_PMA_PMD_DEV_TYPE,
- reg);
- if (status)
- return status;
+ /* If PHY FW reset completed bit is set then this is the first
+ * SW instance after a power on so the PHY FW must be un-stalled.
+ */
+ if (reg & IXGBE_MDIO_TX_VENDOR_ALARMS_3_RST_MASK) {
+ status = hw->phy.ops.read_reg(hw,
+ IXGBE_MDIO_GLOBAL_RES_PR_10,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ ®);
+ if (status)
+ return status;
- /* Un-stall the PHY FW */
- status = hw->phy.ops.read_reg(hw,
- IXGBE_MDIO_GLOBAL_RES_PR_10,
- IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
- ®);
- if (status)
- return status;
+ reg &= ~IXGBE_MDIO_POWER_UP_STALL;
- reg &= ~IXGBE_MDIO_POWER_UP_STALL;
+ status = hw->phy.ops.write_reg(hw,
+ IXGBE_MDIO_GLOBAL_RES_PR_10,
+ IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
+ reg);
+ if (status)
+ return status;
+ }
- status = hw->phy.ops.write_reg(hw,
- IXGBE_MDIO_GLOBAL_RES_PR_10,
- IXGBE_MDIO_VENDOR_SPECIFIC_1_DEV_TYPE,
- reg);
return status;
}
Reviewing the X550 copper initi flow with the Si team resulted in a new simplified flow. We no longer wait for the PHY FW initialization complete bit to be set as this bit is only set once by the PHY at power on and then cleared on the first read. So only the first instance of running SW (or possibly MAC FW) needs to initialize the PHY. The PHY initialization has been simplified and now only requires that the PHY FW be un-stalled low-power mode or enabled the transceiver Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> --- drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c | 68 +++++++------------------ 1 file changed, 19 insertions(+), 49 deletions(-)