| Message ID | 20230619040742.1108172-2-chris.packham@alliedtelesis.co.nz |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
| Series | dt-bindings: mtd: marvell-nand: Add YAML scheme | expand |
| Context | Check | Description |
|---|---|---|
| robh/checkpatch | warning | total: 0 errors, 1 warnings, 233 lines checked |
| robh/patch-applied | success | |
| robh/dt-meta-schema | fail | build log |
On Mon, 19 Jun 2023 16:07:42 +1200, Chris Packham wrote: > From: Vadym Kochan <vadym.kochan@plvision.eu> > > Switch the DT binding to a YAML schema to enable the DT validation. > > There was also an incorrect reference to dma-names being "rxtx" where > the driver and existing device trees actually use dma-names = "data" so > this is corrected in the conversion. > > Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu> > Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> > --- > > Notes: > Changes in v10: > - Formatting for description > - Restrict clocks to 1 item for non-8K devices > - Don't allow "marvell,armada-8k-nand-controller" without > "marvell,armada370-nand-controller" (undoes a change from v8) > > Changes in v9: > - depend on series from Miquel > https://lore.kernel.org/linux-mtd/20230606175246.190465-1-miquel.raynal@bootlin.com/ > - enforce minimum/maximum for nand-rb > - move required: block for controller > - move unevaluatedProperties: for nand chip > - remove label, partitions and nand-on-flash-bbt which are covered by > generic schema > > Changes in v8: > - Mark deprecated compatible values as such > - Allow "marvell,armada-8k-nand-controller" without > "marvell,armada370-nand-controller" > - Make dma-names usage reflect reality > - Update commit message > > Changes in v7: > - Restore "label" and "partitions" properties (should be picked up via > nand-controller.yaml but aren't) > - Add/restore nand-on-flash-bbt and nand-ecc-mode which aren't covered > by nand-controller.yaml. > - Use "unevalautedProperties: false" > - Corrections for clock-names, dma-names, nand-rb and nand-ecc-strength > - Add pxa3xx-nand-controller example > > Changes in v6: > - remove properties covered by nand-controller.yaml > - add example using armada-8k compatible > > earlier changes: > > v5: > 1) Get back "label" and "partitions" properties but without > ref to the "partition.yaml" which was wrongly used. > > 2) Add "additionalProperties: false" for nand@ because all possible > properties are described. > > v4: > 1) Remove "label" and "partitions" properties > > 2) Use 2 clocks for A7K/8K platform which is a requirement > > v3: > 1) Remove txt version from the MAINTAINERS list > > 2) Use enum for some of compatible strings > > 3) Drop: > #address-cells > #size-cells: > > as they are inherited from the nand-controller.yaml > > 4) Add restriction to use 2 clocks for A8K SoC > > 5) Dropped description for clock-names and extend it with > minItems: 1 > > 6) Drop description for "dmas" > > 7) Use "unevalautedProperties: false" > > 8) Drop quites from yaml refs. > > 9) Use 4-space indentation for the example section > > v2: > 1) Fixed warning by yamllint with incorrect indentation for compatible list > > .../bindings/mtd/marvell,nand-controller.yaml | 226 ++++++++++++++++++ > .../devicetree/bindings/mtd/marvell-nand.txt | 126 ---------- > MAINTAINERS | 1 - > 3 files changed, 226 insertions(+), 127 deletions(-) > create mode 100644 Documentation/devicetree/bindings/mtd/marvell,nand-controller.yaml > delete mode 100644 Documentation/devicetree/bindings/mtd/marvell-nand.txt > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: dtschema/dtc warnings/errors: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mtd/marvell,nand-controller.yaml: Error in referenced schema matching $id: http://devicetree.org/schemas/mtd/raw-nand-chip.yaml /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mtd/marvell,nand-controller.example.dtb: nand-controller@d0000: nand@0: False schema does not allow {'reg': [[0]], 'label': ['main-storage'], 'nand-rb': [[0]], 'nand-ecc-mode': ['hw'], 'marvell,nand-keep-config': True, 'nand-on-flash-bbt': True, 'nand-ecc-strength': [[4]], 'nand-ecc-step-size': [[512]], 'partitions': {'compatible': ['fixed-partitions'], '#address-cells': [[1]], '#size-cells': [[1]], 'partition@0': {'label': ['Rootfs'], 'reg': [[0, 1073741824]]}}} from schema $id: http://devicetree.org/schemas/mtd/marvell,nand-controller.yaml# /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mtd/marvell,nand-controller.example.dtb: nand-controller@d0000: nand@0: Unevaluated properties are not allowed ('label', 'nand-on-flash-bbt', 'partitions' were unexpected) from schema $id: http://devicetree.org/schemas/mtd/marvell,nand-controller.yaml# /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mtd/marvell,nand-controller.example.dtb: nand-controller@720000: nand@0: False schema does not allow {'reg': [[0]], 'label': ['main-storage'], 'nand-rb': [[0]], 'nand-ecc-mode': ['hw'], 'nand-ecc-strength': [[8]], 'nand-ecc-step-size': [[512]]} from schema $id: http://devicetree.org/schemas/mtd/marvell,nand-controller.yaml# /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mtd/marvell,nand-controller.example.dtb: nand-controller@720000: nand@0: Unevaluated properties are not allowed ('label' was unexpected) from schema $id: http://devicetree.org/schemas/mtd/marvell,nand-controller.yaml# /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/mtd/marvell,nand-controller.example.dtb: nand-controller@43100000: nand@0: False schema does not allow {'reg': [[0]], 'nand-rb': [[0]], 'nand-ecc-mode': ['hw'], 'marvell,nand-keep-config': True} from schema $id: http://devicetree.org/schemas/mtd/marvell,nand-controller.yaml# doc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230619040742.1108172-2-chris.packham@alliedtelesis.co.nz The base for the series is generally the latest rc1. A different dependency should be noted in *this* patch. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit after running the above command yourself. Note that DT_SCHEMA_FILES can be set to your schema file to speed up checking your schema. However, it must be unset to test all examples with your schema.
On Mon, 19 Jun 2023 16:07:42 +1200, Chris Packham wrote: > From: Vadym Kochan <vadym.kochan@plvision.eu> > > Switch the DT binding to a YAML schema to enable the DT validation. > > There was also an incorrect reference to dma-names being "rxtx" where > the driver and existing device trees actually use dma-names = "data" so > this is corrected in the conversion. > > Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu> > Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> > --- > > Notes: > Changes in v10: > - Formatting for description > - Restrict clocks to 1 item for non-8K devices > - Don't allow "marvell,armada-8k-nand-controller" without > "marvell,armada370-nand-controller" (undoes a change from v8) > > Changes in v9: > - depend on series from Miquel > https://lore.kernel.org/linux-mtd/20230606175246.190465-1-miquel.raynal@bootlin.com/ > - enforce minimum/maximum for nand-rb > - move required: block for controller > - move unevaluatedProperties: for nand chip > - remove label, partitions and nand-on-flash-bbt which are covered by > generic schema > > Changes in v8: > - Mark deprecated compatible values as such > - Allow "marvell,armada-8k-nand-controller" without > "marvell,armada370-nand-controller" > - Make dma-names usage reflect reality > - Update commit message > > Changes in v7: > - Restore "label" and "partitions" properties (should be picked up via > nand-controller.yaml but aren't) > - Add/restore nand-on-flash-bbt and nand-ecc-mode which aren't covered > by nand-controller.yaml. > - Use "unevalautedProperties: false" > - Corrections for clock-names, dma-names, nand-rb and nand-ecc-strength > - Add pxa3xx-nand-controller example > > Changes in v6: > - remove properties covered by nand-controller.yaml > - add example using armada-8k compatible > > earlier changes: > > v5: > 1) Get back "label" and "partitions" properties but without > ref to the "partition.yaml" which was wrongly used. > > 2) Add "additionalProperties: false" for nand@ because all possible > properties are described. > > v4: > 1) Remove "label" and "partitions" properties > > 2) Use 2 clocks for A7K/8K platform which is a requirement > > v3: > 1) Remove txt version from the MAINTAINERS list > > 2) Use enum for some of compatible strings > > 3) Drop: > #address-cells > #size-cells: > > as they are inherited from the nand-controller.yaml > > 4) Add restriction to use 2 clocks for A8K SoC > > 5) Dropped description for clock-names and extend it with > minItems: 1 > > 6) Drop description for "dmas" > > 7) Use "unevalautedProperties: false" > > 8) Drop quites from yaml refs. > > 9) Use 4-space indentation for the example section > > v2: > 1) Fixed warning by yamllint with incorrect indentation for compatible list > > .../bindings/mtd/marvell,nand-controller.yaml | 226 ++++++++++++++++++ > .../devicetree/bindings/mtd/marvell-nand.txt | 126 ---------- > MAINTAINERS | 1 - > 3 files changed, 226 insertions(+), 127 deletions(-) > create mode 100644 Documentation/devicetree/bindings/mtd/marvell,nand-controller.yaml > delete mode 100644 Documentation/devicetree/bindings/mtd/marvell-nand.txt > Reviewed-by: Rob Herring <robh@kernel.org>
On Mon, 2023-06-19 at 04:07:42 UTC, Chris Packham wrote: > From: Vadym Kochan <vadym.kochan@plvision.eu> > > Switch the DT binding to a YAML schema to enable the DT validation. > > There was also an incorrect reference to dma-names being "rxtx" where > the driver and existing device trees actually use dma-names = "data" so > this is corrected in the conversion. > > Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu> > Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> > Reviewed-by: Rob Herring <robh@kernel.org> Applied to https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git nand/next, thanks. Miquel
diff --git a/Documentation/devicetree/bindings/mtd/marvell,nand-controller.yaml b/Documentation/devicetree/bindings/mtd/marvell,nand-controller.yaml new file mode 100644 index 000000000000..a10729bb1840 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/marvell,nand-controller.yaml @@ -0,0 +1,226 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mtd/marvell,nand-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell NAND Flash Controller (NFC) + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + +properties: + compatible: + oneOf: + - items: + - const: marvell,armada-8k-nand-controller + - const: marvell,armada370-nand-controller + - enum: + - marvell,armada370-nand-controller + - marvell,pxa3xx-nand-controller + - description: legacy bindings + deprecated: true + enum: + - marvell,armada-8k-nand + - marvell,armada370-nand + - marvell,pxa3xx-nand + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + description: + Shall reference the NAND controller clocks, the second one is + is only needed for the Armada 7K/8K SoCs + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + items: + - const: core + - const: reg + + dmas: + maxItems: 1 + + dma-names: + items: + - const: data + + marvell,system-controller: + $ref: /schemas/types.yaml#/definitions/phandle + description: Syscon node that handles NAND controller related registers + +patternProperties: + "^nand@[a-f0-9]$": + type: object + $ref: raw-nand-chip.yaml + + properties: + reg: + minimum: 0 + maximum: 3 + + nand-rb: + items: + - minimum: 0 + maximum: 1 + + nand-ecc-step-size: + const: 512 + + nand-ecc-strength: + enum: [1, 4, 8, 12, 16] + + nand-ecc-mode: + const: hw + + marvell,nand-keep-config: + $ref: /schemas/types.yaml#/definitions/flag + description: + Orders the driver not to take the timings from the core and + leaving them completely untouched. Bootloader timings will then + be used. + + marvell,nand-enable-arbiter: + $ref: /schemas/types.yaml#/definitions/flag + description: + To enable the arbiter, all boards blindly used it, + this bit was set by the bootloader for many boards and even if + it is marked reserved in several datasheets, it might be needed to set + it (otherwise it is harmless). + deprecated: true + + required: + - reg + - nand-rb + + unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + +allOf: + - $ref: nand-controller.yaml# + + - if: + properties: + compatible: + contains: + const: marvell,pxa3xx-nand-controller + then: + required: + - dmas + - dma-names + + - if: + properties: + compatible: + contains: + const: marvell,armada-8k-nand-controller + then: + properties: + clocks: + minItems: 2 + + clock-names: + minItems: 2 + + required: + - marvell,system-controller + + else: + properties: + clocks: + minItems: 1 + + clock-names: + minItems: 1 + + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + nand_controller: nand-controller@d0000 { + compatible = "marvell,armada370-nand-controller"; + reg = <0xd0000 0x54>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&coredivclk 0>; + + nand@0 { + reg = <0>; + label = "main-storage"; + nand-rb = <0>; + nand-ecc-mode = "hw"; + marvell,nand-keep-config; + nand-on-flash-bbt; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Rootfs"; + reg = <0x00000000 0x40000000>; + }; + }; + }; + }; + + - | + cp0_nand_controller: nand-controller@720000 { + compatible = "marvell,armada-8k-nand-controller", + "marvell,armada370-nand-controller"; + reg = <0x720000 0x54>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <115 IRQ_TYPE_LEVEL_HIGH>; + clock-names = "core", "reg"; + clocks = <&cp0_clk 1 2>, + <&cp0_clk 1 17>; + marvell,system-controller = <&cp0_syscon0>; + + nand@0 { + reg = <0>; + label = "main-storage"; + nand-rb = <0>; + nand-ecc-mode = "hw"; + nand-ecc-strength = <8>; + nand-ecc-step-size = <512>; + }; + }; + + - | + nand-controller@43100000 { + compatible = "marvell,pxa3xx-nand-controller"; + reg = <0x43100000 90>; + interrupts = <45>; + clocks = <&clks 1>; + clock-names = "core"; + dmas = <&pdma 97 3>; + dma-names = "data"; + #address-cells = <1>; + #size-cells = <0>; + nand@0 { + reg = <0>; + nand-rb = <0>; + nand-ecc-mode = "hw"; + marvell,nand-keep-config; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/mtd/marvell-nand.txt b/Documentation/devicetree/bindings/mtd/marvell-nand.txt deleted file mode 100644 index a2d9a0f2b683..000000000000 --- a/Documentation/devicetree/bindings/mtd/marvell-nand.txt +++ /dev/null @@ -1,126 +0,0 @@ -Marvell NAND Flash Controller (NFC) - -Required properties: -- compatible: can be one of the following: - * "marvell,armada-8k-nand-controller" - * "marvell,armada370-nand-controller" - * "marvell,pxa3xx-nand-controller" - * "marvell,armada-8k-nand" (deprecated) - * "marvell,armada370-nand" (deprecated) - * "marvell,pxa3xx-nand" (deprecated) - Compatibles marked deprecated support only the old bindings described - at the bottom. -- reg: NAND flash controller memory area. -- #address-cells: shall be set to 1. Encode the NAND CS. -- #size-cells: shall be set to 0. -- interrupts: shall define the NAND controller interrupt. -- clocks: shall reference the NAND controller clocks, the second one is - is only needed for the Armada 7K/8K SoCs -- clock-names: mandatory if there is a second clock, in this case there - should be one clock named "core" and another one named "reg" -- marvell,system-controller: Set to retrieve the syscon node that handles - NAND controller related registers (only required with the - "marvell,armada-8k-nand[-controller]" compatibles). - -Optional properties: -- label: see partition.txt. New platforms shall omit this property. -- dmas: shall reference DMA channel associated to the NAND controller. - This property is only used with "marvell,pxa3xx-nand[-controller]" - compatible strings. -- dma-names: shall be "rxtx". - This property is only used with "marvell,pxa3xx-nand[-controller]" - compatible strings. - -Optional children nodes: -Children nodes represent the available NAND chips. - -Required properties: -- reg: shall contain the native Chip Select ids (0-3). -- nand-rb: see nand-controller.yaml (0-1). - -Optional properties: -- marvell,nand-keep-config: orders the driver not to take the timings - from the core and leaving them completely untouched. Bootloader - timings will then be used. -- label: MTD name. -- nand-on-flash-bbt: see nand-controller.yaml. -- nand-ecc-mode: see nand-controller.yaml. Will use hardware ECC if not specified. -- nand-ecc-algo: see nand-controller.yaml. This property is essentially useful when - not using hardware ECC. Howerver, it may be added when using hardware - ECC for clarification but will be ignored by the driver because ECC - mode is chosen depending on the page size and the strength required by - the NAND chip. This value may be overwritten with nand-ecc-strength - property. -- nand-ecc-strength: see nand-controller.yaml. -- nand-ecc-step-size: see nand-controller.yaml. Marvell's NAND flash controller does - use fixed strength (1-bit for Hamming, 16-bit for BCH), so the actual - step size will shrink or grow in order to fit the required strength. - Step sizes are not completely random for all and follow certain - patterns described in AN-379, "Marvell SoC NFC ECC". - -See Documentation/devicetree/bindings/mtd/nand-controller.yaml for more details on -generic bindings. - - -Example: -nand_controller: nand-controller@d0000 { - compatible = "marvell,armada370-nand-controller"; - reg = <0xd0000 0x54>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&coredivclk 0>; - - nand@0 { - reg = <0>; - label = "main-storage"; - nand-rb = <0>; - nand-ecc-mode = "hw"; - marvell,nand-keep-config; - nand-on-flash-bbt; - nand-ecc-strength = <4>; - nand-ecc-step-size = <512>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "Rootfs"; - reg = <0x00000000 0x40000000>; - }; - }; - }; -}; - - -Note on legacy bindings: One can find, in not-updated device trees, -bindings slightly different than described above with other properties -described below as well as the partitions node at the root of a so -called "nand" node (without clear controller/chip separation). - -Legacy properties: -- marvell,nand-enable-arbiter: To enable the arbiter, all boards blindly - used it, this bit was set by the bootloader for many boards and even if - it is marked reserved in several datasheets, it might be needed to set - it (otherwise it is harmless) so whether or not this property is set, - the bit is selected by the driver. -- num-cs: Number of chip-select lines to use, all boards blindly set 1 - to this and for a reason, other values would have failed. The value of - this property is ignored. - -Example: - - nand0: nand@43100000 { - compatible = "marvell,pxa3xx-nand"; - reg = <0x43100000 90>; - interrupts = <45>; - dmas = <&pdma 97 0>; - dma-names = "rxtx"; - #address-cells = <1>; - marvell,nand-keep-config; - marvell,nand-enable-arbiter; - num-cs = <1>; - /* Partitions (optional) */ - }; diff --git a/MAINTAINERS b/MAINTAINERS index 5d463f171c90..5342798d4e4f 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -12448,7 +12448,6 @@ MARVELL NAND CONTROLLER DRIVER M: Miquel Raynal <miquel.raynal@bootlin.com> L: linux-mtd@lists.infradead.org S: Maintained -F: Documentation/devicetree/bindings/mtd/marvell-nand.txt F: drivers/mtd/nand/raw/marvell_nand.c MARVELL OCTEONTX2 PHYSICAL FUNCTION DRIVER