From patchwork Wed Jun 12 12:25:27 2019 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Nicolas Saenz Julienne X-Patchwork-Id: 1114537 Return-Path: X-Original-To: incoming-dt@patchwork.ozlabs.org Delivered-To: patchwork-incoming-dt@bilbo.ozlabs.org Authentication-Results: ozlabs.org; spf=none (mailfrom) smtp.mailfrom=vger.kernel.org (client-ip=209.132.180.67; helo=vger.kernel.org; envelope-from=devicetree-owner@vger.kernel.org; receiver=) Authentication-Results: ozlabs.org; dmarc=none (p=none dis=none) header.from=suse.de Received: from vger.kernel.org (vger.kernel.org [209.132.180.67]) by ozlabs.org (Postfix) with ESMTP id 45P5jD3kcKz9s4Y for ; Wed, 12 Jun 2019 22:27:12 +1000 (AEST) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1726941AbfFLM1L (ORCPT ); Wed, 12 Jun 2019 08:27:11 -0400 Received: from mx2.suse.de ([195.135.220.15]:48006 "EHLO mx1.suse.de" rhost-flags-OK-OK-OK-FAIL) by vger.kernel.org with ESMTP id S1727249AbfFLM1L (ORCPT ); Wed, 12 Jun 2019 08:27:11 -0400 X-Virus-Scanned: by amavisd-new at test-mx.suse.de Received: from relay2.suse.de (unknown [195.135.220.254]) by mx1.suse.de (Postfix) with ESMTP id D2A1EAE12; Wed, 12 Jun 2019 12:27:09 +0000 (UTC) From: Nicolas Saenz Julienne To: "David S. Miller" Cc: Nicolas Saenz Julienne , Rob Herring , Mark Rutland , netdev@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org Subject: [PATCH v2 2/2] dt-bindings: net: wiznet: add w5x00 support Date: Wed, 12 Jun 2019 14:25:27 +0200 Message-Id: <20190612122526.14332-2-nsaenzjulienne@suse.de> X-Mailer: git-send-email 2.21.0 In-Reply-To: <20190612122526.14332-1-nsaenzjulienne@suse.de> References: <20190612122526.14332-1-nsaenzjulienne@suse.de> MIME-Version: 1.0 Sender: devicetree-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: devicetree@vger.kernel.org Add bindings for Wiznet's w5x00 series of SPI interfaced Ethernet chips. Based on the bindings for microchip,enc28j60. Signed-off-by: Nicolas Saenz Julienne --- Changes since v1: - one compatible sting per line - use correct 'ethenet@0' phandle name .../devicetree/bindings/net/wiznet,w5x00.txt | 51 +++++++++++++++++++ 1 file changed, 51 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/wiznet,w5x00.txt diff --git a/Documentation/devicetree/bindings/net/wiznet,w5x00.txt b/Documentation/devicetree/bindings/net/wiznet,w5x00.txt new file mode 100644 index 000000000000..901946dea3de --- /dev/null +++ b/Documentation/devicetree/bindings/net/wiznet,w5x00.txt @@ -0,0 +1,51 @@ +* Wiznet w5x00 + +This is a standalone 10/100 MBit Ethernet controller with SPI interface. + +For each device connected to a SPI bus, define a child node within +the SPI master node. + +Required properties: +- compatible: Should be one of the following strings: + "wiznet,w5100" + "wiznet,w5200" + "wiznet,w5500" +- reg: Specify the SPI chip select the chip is wired to. +- interrupts: Specify the interrupt index within the interrupt controller (referred + to above in interrupt-parent) and interrupt type. w5x00 natively + generates falling edge interrupts, however, additional board logic + might invert the signal. +- pinctrl-names: List of assigned state names, see pinctrl binding documentation. +- pinctrl-0: List of phandles to configure the GPIO pin used as interrupt line, + see also generic and your platform specific pinctrl binding + documentation. + +Optional properties: +- spi-max-frequency: Maximum frequency of the SPI bus when accessing the w5500. + According to the w5500 datasheet, the chip allows a maximum of 80 MHz, however, + board designs may need to limit this value. +- local-mac-address: See ethernet.txt in the same directory. + + +Example (for Raspberry Pi with pin control stuff for GPIO irq): + +&spi { + ethernet@0: w5500@0 { + compatible = "wiznet,w5500"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <ð1_pins>; + interrupt-parent = <&gpio>; + interrupts = <25 IRQ_TYPE_EDGE_FALLING>; + spi-max-frequency = <30000000>; + }; +}; + +&gpio { + eth1_pins: eth1_pins { + brcm,pins = <25>; + brcm,function = <0>; /* in */ + brcm,pull = <0>; /* none */ + }; +}; +