| Message ID | 1487268237-4240-3-git-send-email-bgolaszewski@baylibre.com |
|---|---|
| State | Superseded, archived |
| Headers | show |
On Thu, Feb 16, 2017 at 12:03 PM, Bartosz Golaszewski <bgolaszewski@baylibre.com> wrote: > This makes the example more or less correspond with the da850-evm > hardware setup. > > Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> > --- > .../devicetree/bindings/media/ti,da850-vpif.txt | 36 +++++++++++++++++----- > 1 file changed, 29 insertions(+), 7 deletions(-) > > diff --git a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt > index 9c7510b..d6f93a1 100644 > --- a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt > +++ b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt > @@ -16,7 +16,7 @@ Required properties: > Video Capture: > > VPIF has a 16-bit parallel bus input, supporting 2 8-bit channels or a > -single 16-bit channel. It should contain at least one port child node > +single 16-bit channel. It should contain one or two port child nodes When do you not have an output? Seems kind of useless. I'm guessing this is an oversight in the binding and there should always be port 1 and a connector node, so document it that way. This also needs to state what port 0 and port 1 are (i.e. input or output and type of data). > with child 'endpoint' node. Please refer to the bindings defined in > Documentation/devicetree/bindings/media/video-interfaces.txt. > > @@ -28,19 +28,26 @@ I2C-connected TVP5147 decoder: > reg = <0x217000 0x1000>; > interrupts = <92>; > > - port { > - vpif_ch0: endpoint@0 { > + port@0 { > + vpif_input_ch0: endpoint@0 { > reg = <0>; > bus-width = <8>; > - remote-endpoint = <&composite>; > + remote-endpoint = <&composite_in>; > }; > > - vpif_ch1: endpoint@1 { > + vpif_input_ch1: endpoint@1 { > reg = <1>; > bus-width = <8>; > data-shift = <8>; > }; > }; > + > + port@1 { > + vpif_output_ch0: endpoint { > + bus-width = <8>; Isn't this an analog input? bus-width doesn't make sense for that. Rob -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
2017-02-21 15:57 GMT+01:00 Rob Herring <robh+dt@kernel.org>: > On Thu, Feb 16, 2017 at 12:03 PM, Bartosz Golaszewski > <bgolaszewski@baylibre.com> wrote: >> This makes the example more or less correspond with the da850-evm >> hardware setup. >> >> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> >> --- >> .../devicetree/bindings/media/ti,da850-vpif.txt | 36 +++++++++++++++++----- >> 1 file changed, 29 insertions(+), 7 deletions(-) >> >> diff --git a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt >> index 9c7510b..d6f93a1 100644 >> --- a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt >> +++ b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt >> @@ -16,7 +16,7 @@ Required properties: >> Video Capture: >> >> VPIF has a 16-bit parallel bus input, supporting 2 8-bit channels or a >> -single 16-bit channel. It should contain at least one port child node >> +single 16-bit channel. It should contain one or two port child nodes > > When do you not have an output? Seems kind of useless. I'm guessing > this is an oversight in the binding and there should always be port 1 > and a connector node, so document it that way. > Sometimes the output pins are not hooked up to anything - for example on the da850-lcdk board we only use input for camera capture, while on da850-evm we have both composite and s-video outputs and inputs. I think it makes sens to leave out the output port if we don't use it. > This also needs to state what port 0 and port 1 are (i.e. input or > output and type of data). > I'll fix that. >> with child 'endpoint' node. Please refer to the bindings defined in >> Documentation/devicetree/bindings/media/video-interfaces.txt. >> >> @@ -28,19 +28,26 @@ I2C-connected TVP5147 decoder: >> reg = <0x217000 0x1000>; >> interrupts = <92>; >> >> - port { >> - vpif_ch0: endpoint@0 { >> + port@0 { >> + vpif_input_ch0: endpoint@0 { >> reg = <0>; >> bus-width = <8>; >> - remote-endpoint = <&composite>; >> + remote-endpoint = <&composite_in>; >> }; >> >> - vpif_ch1: endpoint@1 { >> + vpif_input_ch1: endpoint@1 { >> reg = <1>; >> bus-width = <8>; >> data-shift = <8>; >> }; >> }; >> + >> + port@1 { >> + vpif_output_ch0: endpoint { >> + bus-width = <8>; > > Isn't this an analog input? bus-width doesn't make sense for that. > Not yet - the signals first go to a video DAC (adv7343 in the example). Thanks, Bartosz -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt index 9c7510b..d6f93a1 100644 --- a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt +++ b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt @@ -16,7 +16,7 @@ Required properties: Video Capture: VPIF has a 16-bit parallel bus input, supporting 2 8-bit channels or a -single 16-bit channel. It should contain at least one port child node +single 16-bit channel. It should contain one or two port child nodes with child 'endpoint' node. Please refer to the bindings defined in Documentation/devicetree/bindings/media/video-interfaces.txt. @@ -28,19 +28,26 @@ I2C-connected TVP5147 decoder: reg = <0x217000 0x1000>; interrupts = <92>; - port { - vpif_ch0: endpoint@0 { + port@0 { + vpif_input_ch0: endpoint@0 { reg = <0>; bus-width = <8>; - remote-endpoint = <&composite>; + remote-endpoint = <&composite_in>; }; - vpif_ch1: endpoint@1 { + vpif_input_ch1: endpoint@1 { reg = <1>; bus-width = <8>; data-shift = <8>; }; }; + + port@1 { + vpif_output_ch0: endpoint { + bus-width = <8>; + remote-endpoint = <&composite_out>; + }; + }; }; [ ... ] @@ -53,13 +60,28 @@ I2C-connected TVP5147 decoder: status = "okay"; port { - composite: endpoint { + composite_in: endpoint { hsync-active = <1>; vsync-active = <1>; pclk-sample = <0>; /* VPIF channel 0 (lower 8-bits) */ - remote-endpoint = <&vpif_ch0>; + remote-endpoint = <&vpif_input_ch0>; + bus-width = <8>; + }; + }; + }; + + adv7343@2a { + compatible = "adi,adv7343"; + reg = <0x2a>; + + port { + composite_out: endpoint { + adi,dac-enable = <1 1 1>; + adi,sd-dac-enable = <1>; + + remote-endpoint = <&vpif_output_ch0>; bus-width = <8>; }; };
This makes the example more or less correspond with the da850-evm hardware setup. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> --- .../devicetree/bindings/media/ti,da850-vpif.txt | 36 +++++++++++++++++----- 1 file changed, 29 insertions(+), 7 deletions(-)