| Message ID | 1435060743-5511-7-git-send-email-kishon@ti.com |
|---|---|
| State | Needs Review / ACK, archived |
| Headers | show |
| Context | Check | Description |
|---|---|---|
| robh/checkpatch | warning | total: 1 errors, 0 warnings, 0 lines checked |
| robh/patch-applied | success |
On Tue, 23 Jun 2015 17:28:51 +0530 Kishon Vijay Abraham I <kishon@ti.com> wrote: > Deprecate using phy-omap-control driver to power on/off the PHY, > and use *syscon* framework to do the same. This handles > powering on/off the PHY for the USB2 PHYs used in various TI SoCs. > > Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> > --- > Documentation/devicetree/bindings/phy/ti-phy.txt | 6 +- > drivers/phy/phy-omap-usb2.c | 101 ++++++++++++++++++---- > include/linux/phy/omap_usb.h | 18 ++++ > 3 files changed, 107 insertions(+), 18 deletions(-) > > diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt > index b9101b9..5bfe461 100644 > --- a/Documentation/devicetree/bindings/phy/ti-phy.txt > +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt > @@ -42,10 +42,14 @@ Required properties: > * "wkupclk" - wakeup clock. > * "refclk" - reference clock (optional). > > -Optional properties: > +Deprecated properties: > - ctrl-module : phandle of the control module used by PHY driver to power on > the PHY. > > +Recommended properies: > +- syscon-phy-power : phandle/offset pair. Phandle to the system control > + module and the register offset to power on/off the PHY. > + > This is usually a subnode of ocp2scp to which it is connected. > > usb2phy@4a0ad080 { > diff --git a/drivers/phy/phy-omap-usb2.c b/drivers/phy/phy-omap-usb2.c > index 2f7220f..180b066 100644 > --- a/drivers/phy/phy-omap-usb2.c > +++ b/drivers/phy/phy-omap-usb2.c > @@ -29,6 +29,8 @@ > #include <linux/delay.h> > #include <linux/phy/omap_control_phy.h> > #include <linux/phy/phy.h> > +#include <linux/mfd/syscon.h> > +#include <linux/regmap.h> > #include <linux/of_platform.h> > > #define USB2PHY_DISCON_BYP_LATCH (1 << 31) > @@ -97,22 +99,65 @@ static int omap_usb_set_peripheral(struct usb_otg *otg, > return 0; > } > > -static int omap_usb_power_off(struct phy *x) > +static int omap_usb_phy_power(struct omap_usb *phy, int on) > { > - struct omap_usb *phy = phy_get_drvdata(x); > + u32 val = 0; > + u32 mask; > + int ret; > > - omap_control_phy_power(phy->control_dev, 0); > + if (phy->syscon_phy_power) { > + switch (phy->type) { > + case TYPE_USB2: > + mask = OMAP_DEV_PHY_PD; > + if (!on) > + val = OMAP_DEV_PHY_PD; > + break; > + case TYPE_DRA7USB2: > + mask = OMAP_USB2_PHY_PD; > + if (!on) > + val = OMAP_USB2_PHY_PD; > + break; > + case TYPE_AM437USB2: > + mask = AM437X_USB2_PHY_PD | > + AM437X_USB2_OTG_PD | > + AM437X_USB2_OTGVDET_EN | > + AM437X_USB2_OTGSESSEND_EN; > + if (on) { > + val = AM437X_USB2_OTGVDET_EN | > + AM437X_USB2_OTGSESSEND_EN; > + } else { > + val = AM437X_USB2_PHY_PD | AM437X_USB2_OTG_PD; > + } > + break; > + default: > + dev_err(phy->dev, "%s: type %d not recognized\n", > + __func__, phy->type); > + return -EINVAL; > + } > + > + ret = regmap_update_bits(phy->syscon_phy_power, phy->power_reg, > + mask, val); > + if (ret < 0) > + return ret; > + } else { > + omap_control_phy_power(phy->control_dev, on); > + } > > return 0; > } > > -static int omap_usb_power_on(struct phy *x) > +static int omap_usb_power_off(struct phy *x) > { > struct omap_usb *phy = phy_get_drvdata(x); > > - omap_control_phy_power(phy->control_dev, 1); > + return omap_usb_phy_power(phy, false); > +} > > - return 0; > +static int omap_usb_power_on(struct phy *x) > +{ > + struct omap_usb *phy = phy_get_drvdata(x); > + > + return omap_usb_phy_power(phy, true); > } > > static int omap_usb_init(struct phy *x) > @@ -147,26 +192,31 @@ static struct phy_ops ops = { > static const struct usb_phy_data omap_usb2_data = { > .label = "omap_usb2", > .flags = OMAP_USB2_HAS_START_SRP | OMAP_USB2_HAS_SET_VBUS, > + .type = TYPE_USB2, > }; > > static const struct usb_phy_data omap5_usb2_data = { > .label = "omap5_usb2", > .flags = 0, > + .type = TYPE_USB2, > }; > > static const struct usb_phy_data dra7x_usb2_data = { > .label = "dra7x_usb2", > .flags = OMAP_USB2_CALIBRATE_FALSE_DISCONNECT, > + .type = TYPE_USB2, > }; > > static const struct usb_phy_data dra7x_usb2_phy2_data = { > .label = "dra7x_usb2_phy2", > .flags = OMAP_USB2_CALIBRATE_FALSE_DISCONNECT, > + .type = TYPE_DRA7USB2, > }; > > static const struct usb_phy_data am437x_usb2_data = { > .label = "am437x_usb2", > .flags = 0, > + .type = TYPE_AM437USB2, > }; > > static const struct of_device_id omap_usb2_id_table[] = { > @@ -223,6 +273,7 @@ static int omap_usb2_probe(struct platform_device *pdev) > return -ENOMEM; > > phy->dev = &pdev->dev; > + phy->type = phy_data->type; > > phy->phy.dev = phy->dev; > phy->phy.label = phy_data->label; > @@ -237,20 +288,36 @@ static int omap_usb2_probe(struct platform_device *pdev) > phy->flags |= OMAP_USB2_CALIBRATE_FALSE_DISCONNECT; > } > > - control_node = of_parse_phandle(node, "ctrl-module", 0); > - if (!control_node) { > - dev_err(&pdev->dev, "Failed to get control device phandle\n"); > - return -EINVAL; > - } > + phy->syscon_phy_power = syscon_regmap_lookup_by_phandle(node, > + "syscon-phy-power"); > + if (IS_ERR(phy->syscon_phy_power)) { > + dev_info(&pdev->dev, > + "can't get syscon-phy-power, using control device\n"); > + phy->syscon_phy_power = NULL; > + > + control_node = of_parse_phandle(node, "ctrl-module", 0); > + if (!control_node) { > + dev_err(&pdev->dev, > + "Failed to get control device phandle\n"); > + return -EINVAL; > + } > > - control_pdev = of_find_device_by_node(control_node); > - if (!control_pdev) { > - dev_err(&pdev->dev, "Failed to get control device\n"); > - return -EINVAL; > + control_pdev = of_find_device_by_node(control_node); > + if (!control_pdev) { > + dev_err(&pdev->dev, "Failed to get control device\n"); > + return -EINVAL; > + } > + phy->control_dev = &control_pdev->dev; > + } else { > + if (of_property_read_u32_index(node, > + "syscon-phy-power", 1, > + &phy->power_reg)) { > + dev_err(&pdev->dev, > + "couldn't get power reg. offset\n"); > + return -EINVAL; > + } > } > > - phy->control_dev = &control_pdev->dev; > - > otg->set_host = omap_usb_set_host; > otg->set_peripheral = omap_usb_set_peripheral; > if (phy_data->flags & OMAP_USB2_HAS_SET_VBUS) > diff --git a/include/linux/phy/omap_usb.h b/include/linux/phy/omap_usb.h > index dc2c541..de933ab 100644 > --- a/include/linux/phy/omap_usb.h > +++ b/include/linux/phy/omap_usb.h > @@ -30,6 +30,12 @@ struct usb_dpll_params { > u32 mf; > }; > > +enum omap_usb_phy_type { > + TYPE_USB2, /* USB2_PHY, power down in CONTROL_DEV_CONF */ > + TYPE_DRA7USB2, /* USB2 PHY, power and power_aux e.g. DRA7 */ > + TYPE_AM437USB2, /* USB2 PHY, power e.g. AM437x */ > +}; > + > struct omap_usb { > struct usb_phy phy; > struct phy_companion *comparator; > @@ -40,11 +46,15 @@ struct omap_usb { > struct clk *wkupclk; > struct clk *optclk; > u8 flags; > + enum omap_usb_phy_type type; > + struct regmap *syscon_phy_power; /* ctrl. reg. acces */ > + unsigned int power_reg; /* power reg. index within syscon */ > }; > > struct usb_phy_data { > const char *label; > u8 flags; > + enum omap_usb_phy_type type; > }; > > /* Driver Flags */ > @@ -52,6 +62,14 @@ struct usb_phy_data { > #define OMAP_USB2_HAS_SET_VBUS (1 << 1) > #define OMAP_USB2_CALIBRATE_FALSE_DISCONNECT (1 << 2) > > +#define OMAP_DEV_PHY_PD BIT(0) > +#define OMAP_USB2_PHY_PD BIT(28) > + > +#define AM437X_USB2_PHY_PD BIT(0) This PD bit can be set in usb_phy_data and used by a single block of code for all 3 phys. > +#define AM437X_USB2_OTG_PD BIT(1) > +#define AM437X_USB2_OTGVDET_EN BIT(19) > +#define AM437X_USB2_OTGSESSEND_EN BIT(20) > + > #define phy_to_omapusb(x) container_of((x), struct omap_usb, phy) > > #if defined(CONFIG_OMAP_USB2) || defined(CONFIG_OMAP_USB2_MODULE) > -- > 1.7.9.5 > cheers, -roger -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi, On Wednesday 24 June 2015 05:03 PM, Roger Quadros wrote: > On Tue, 23 Jun 2015 17:28:51 +0530 > Kishon Vijay Abraham I <kishon@ti.com> wrote: > >> Deprecate using phy-omap-control driver to power on/off the PHY, >> and use *syscon* framework to do the same. This handles >> powering on/off the PHY for the USB2 PHYs used in various TI SoCs. >> >> Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> >> --- >> Documentation/devicetree/bindings/phy/ti-phy.txt | 6 +- >> drivers/phy/phy-omap-usb2.c | 101 ++++++++++++++++++---- >> include/linux/phy/omap_usb.h | 18 ++++ >> 3 files changed, 107 insertions(+), 18 deletions(-) >> >> diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt >> index b9101b9..5bfe461 100644 >> --- a/Documentation/devicetree/bindings/phy/ti-phy.txt >> +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt >> @@ -42,10 +42,14 @@ Required properties: >> * "wkupclk" - wakeup clock. >> * "refclk" - reference clock (optional). >> >> -Optional properties: >> +Deprecated properties: >> - ctrl-module : phandle of the control module used by PHY driver to power on >> the PHY. >> >> +Recommended properies: >> +- syscon-phy-power : phandle/offset pair. Phandle to the system control >> + module and the register offset to power on/off the PHY. >> + >> This is usually a subnode of ocp2scp to which it is connected. >> >> usb2phy@4a0ad080 { >> diff --git a/drivers/phy/phy-omap-usb2.c b/drivers/phy/phy-omap-usb2.c >> index 2f7220f..180b066 100644 >> --- a/drivers/phy/phy-omap-usb2.c >> +++ b/drivers/phy/phy-omap-usb2.c >> @@ -29,6 +29,8 @@ >> #include <linux/delay.h> >> #include <linux/phy/omap_control_phy.h> >> #include <linux/phy/phy.h> >> +#include <linux/mfd/syscon.h> >> +#include <linux/regmap.h> >> #include <linux/of_platform.h> >> >> #define USB2PHY_DISCON_BYP_LATCH (1 << 31) >> @@ -97,22 +99,65 @@ static int omap_usb_set_peripheral(struct usb_otg *otg, >> return 0; >> } >> >> -static int omap_usb_power_off(struct phy *x) >> +static int omap_usb_phy_power(struct omap_usb *phy, int on) >> { >> - struct omap_usb *phy = phy_get_drvdata(x); >> + u32 val = 0; >> + u32 mask; >> + int ret; >> >> - omap_control_phy_power(phy->control_dev, 0); >> + if (phy->syscon_phy_power) { >> + switch (phy->type) { >> + case TYPE_USB2: >> + mask = OMAP_DEV_PHY_PD; >> + if (!on) >> + val = OMAP_DEV_PHY_PD; >> + break; >> + case TYPE_DRA7USB2: >> + mask = OMAP_USB2_PHY_PD; >> + if (!on) >> + val = OMAP_USB2_PHY_PD; >> + break; >> + case TYPE_AM437USB2: >> + mask = AM437X_USB2_PHY_PD | >> + AM437X_USB2_OTG_PD | >> + AM437X_USB2_OTGVDET_EN | >> + AM437X_USB2_OTGSESSEND_EN; >> + if (on) { >> + val = AM437X_USB2_OTGVDET_EN | >> + AM437X_USB2_OTGSESSEND_EN; >> + } else { >> + val = AM437X_USB2_PHY_PD | AM437X_USB2_OTG_PD; >> + } >> + break; >> + default: >> + dev_err(phy->dev, "%s: type %d not recognized\n", >> + __func__, phy->type); >> + return -EINVAL; >> + } >> + >> + ret = regmap_update_bits(phy->syscon_phy_power, phy->power_reg, >> + mask, val); >> + if (ret < 0) >> + return ret; >> + } else { >> + omap_control_phy_power(phy->control_dev, on); >> + } >> >> return 0; >> } >> >> -static int omap_usb_power_on(struct phy *x) >> +static int omap_usb_power_off(struct phy *x) >> { >> struct omap_usb *phy = phy_get_drvdata(x); >> >> - omap_control_phy_power(phy->control_dev, 1); >> + return omap_usb_phy_power(phy, false); >> +} >> >> - return 0; >> +static int omap_usb_power_on(struct phy *x) >> +{ >> + struct omap_usb *phy = phy_get_drvdata(x); >> + >> + return omap_usb_phy_power(phy, true); >> } >> >> static int omap_usb_init(struct phy *x) >> @@ -147,26 +192,31 @@ static struct phy_ops ops = { >> static const struct usb_phy_data omap_usb2_data = { >> .label = "omap_usb2", >> .flags = OMAP_USB2_HAS_START_SRP | OMAP_USB2_HAS_SET_VBUS, >> + .type = TYPE_USB2, >> }; >> >> static const struct usb_phy_data omap5_usb2_data = { >> .label = "omap5_usb2", >> .flags = 0, >> + .type = TYPE_USB2, >> }; >> >> static const struct usb_phy_data dra7x_usb2_data = { >> .label = "dra7x_usb2", >> .flags = OMAP_USB2_CALIBRATE_FALSE_DISCONNECT, >> + .type = TYPE_USB2, >> }; >> >> static const struct usb_phy_data dra7x_usb2_phy2_data = { >> .label = "dra7x_usb2_phy2", >> .flags = OMAP_USB2_CALIBRATE_FALSE_DISCONNECT, >> + .type = TYPE_DRA7USB2, >> }; >> >> static const struct usb_phy_data am437x_usb2_data = { >> .label = "am437x_usb2", >> .flags = 0, >> + .type = TYPE_AM437USB2, >> }; >> >> static const struct of_device_id omap_usb2_id_table[] = { >> @@ -223,6 +273,7 @@ static int omap_usb2_probe(struct platform_device *pdev) >> return -ENOMEM; >> >> phy->dev = &pdev->dev; >> + phy->type = phy_data->type; >> >> phy->phy.dev = phy->dev; >> phy->phy.label = phy_data->label; >> @@ -237,20 +288,36 @@ static int omap_usb2_probe(struct platform_device *pdev) >> phy->flags |= OMAP_USB2_CALIBRATE_FALSE_DISCONNECT; >> } >> >> - control_node = of_parse_phandle(node, "ctrl-module", 0); >> - if (!control_node) { >> - dev_err(&pdev->dev, "Failed to get control device phandle\n"); >> - return -EINVAL; >> - } >> + phy->syscon_phy_power = syscon_regmap_lookup_by_phandle(node, >> + "syscon-phy-power"); >> + if (IS_ERR(phy->syscon_phy_power)) { >> + dev_info(&pdev->dev, >> + "can't get syscon-phy-power, using control device\n"); >> + phy->syscon_phy_power = NULL; >> + >> + control_node = of_parse_phandle(node, "ctrl-module", 0); >> + if (!control_node) { >> + dev_err(&pdev->dev, >> + "Failed to get control device phandle\n"); >> + return -EINVAL; >> + } >> >> - control_pdev = of_find_device_by_node(control_node); >> - if (!control_pdev) { >> - dev_err(&pdev->dev, "Failed to get control device\n"); >> - return -EINVAL; >> + control_pdev = of_find_device_by_node(control_node); >> + if (!control_pdev) { >> + dev_err(&pdev->dev, "Failed to get control device\n"); >> + return -EINVAL; >> + } >> + phy->control_dev = &control_pdev->dev; >> + } else { >> + if (of_property_read_u32_index(node, >> + "syscon-phy-power", 1, >> + &phy->power_reg)) { >> + dev_err(&pdev->dev, >> + "couldn't get power reg. offset\n"); >> + return -EINVAL; >> + } >> } >> >> - phy->control_dev = &control_pdev->dev; >> - >> otg->set_host = omap_usb_set_host; >> otg->set_peripheral = omap_usb_set_peripheral; >> if (phy_data->flags & OMAP_USB2_HAS_SET_VBUS) >> diff --git a/include/linux/phy/omap_usb.h b/include/linux/phy/omap_usb.h >> index dc2c541..de933ab 100644 >> --- a/include/linux/phy/omap_usb.h >> +++ b/include/linux/phy/omap_usb.h >> @@ -30,6 +30,12 @@ struct usb_dpll_params { >> u32 mf; >> }; >> >> +enum omap_usb_phy_type { >> + TYPE_USB2, /* USB2_PHY, power down in CONTROL_DEV_CONF */ >> + TYPE_DRA7USB2, /* USB2 PHY, power and power_aux e.g. DRA7 */ >> + TYPE_AM437USB2, /* USB2 PHY, power e.g. AM437x */ >> +}; >> + >> struct omap_usb { >> struct usb_phy phy; >> struct phy_companion *comparator; >> @@ -40,11 +46,15 @@ struct omap_usb { >> struct clk *wkupclk; >> struct clk *optclk; >> u8 flags; >> + enum omap_usb_phy_type type; >> + struct regmap *syscon_phy_power; /* ctrl. reg. acces */ >> + unsigned int power_reg; /* power reg. index within syscon */ >> }; >> >> struct usb_phy_data { >> const char *label; >> u8 flags; >> + enum omap_usb_phy_type type; >> }; >> >> /* Driver Flags */ >> @@ -52,6 +62,14 @@ struct usb_phy_data { >> #define OMAP_USB2_HAS_SET_VBUS (1 << 1) >> #define OMAP_USB2_CALIBRATE_FALSE_DISCONNECT (1 << 2) >> >> +#define OMAP_DEV_PHY_PD BIT(0) >> +#define OMAP_USB2_PHY_PD BIT(28) >> + >> +#define AM437X_USB2_PHY_PD BIT(0) > > This PD bit can be set in usb_phy_data and used by > a single block of code for all 3 phys. yeah, that could be done. Thanks Kishon -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt index b9101b9..5bfe461 100644 --- a/Documentation/devicetree/bindings/phy/ti-phy.txt +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt @@ -42,10 +42,14 @@ Required properties: * "wkupclk" - wakeup clock. * "refclk" - reference clock (optional). -Optional properties: +Deprecated properties: - ctrl-module : phandle of the control module used by PHY driver to power on the PHY. +Recommended properies: +- syscon-phy-power : phandle/offset pair. Phandle to the system control + module and the register offset to power on/off the PHY. + This is usually a subnode of ocp2scp to which it is connected. usb2phy@4a0ad080 { diff --git a/drivers/phy/phy-omap-usb2.c b/drivers/phy/phy-omap-usb2.c index 2f7220f..180b066 100644 --- a/drivers/phy/phy-omap-usb2.c +++ b/drivers/phy/phy-omap-usb2.c @@ -29,6 +29,8 @@ #include <linux/delay.h> #include <linux/phy/omap_control_phy.h> #include <linux/phy/phy.h> +#include <linux/mfd/syscon.h> +#include <linux/regmap.h> #include <linux/of_platform.h> #define USB2PHY_DISCON_BYP_LATCH (1 << 31) @@ -97,22 +99,65 @@ static int omap_usb_set_peripheral(struct usb_otg *otg, return 0; } -static int omap_usb_power_off(struct phy *x) +static int omap_usb_phy_power(struct omap_usb *phy, int on) { - struct omap_usb *phy = phy_get_drvdata(x); + u32 val = 0; + u32 mask; + int ret; - omap_control_phy_power(phy->control_dev, 0); + if (phy->syscon_phy_power) { + switch (phy->type) { + case TYPE_USB2: + mask = OMAP_DEV_PHY_PD; + if (!on) + val = OMAP_DEV_PHY_PD; + break; + case TYPE_DRA7USB2: + mask = OMAP_USB2_PHY_PD; + if (!on) + val = OMAP_USB2_PHY_PD; + break; + case TYPE_AM437USB2: + mask = AM437X_USB2_PHY_PD | + AM437X_USB2_OTG_PD | + AM437X_USB2_OTGVDET_EN | + AM437X_USB2_OTGSESSEND_EN; + if (on) { + val = AM437X_USB2_OTGVDET_EN | + AM437X_USB2_OTGSESSEND_EN; + } else { + val = AM437X_USB2_PHY_PD | AM437X_USB2_OTG_PD; + } + break; + default: + dev_err(phy->dev, "%s: type %d not recognized\n", + __func__, phy->type); + return -EINVAL; + } + + ret = regmap_update_bits(phy->syscon_phy_power, phy->power_reg, + mask, val); + if (ret < 0) + return ret; + } else { + omap_control_phy_power(phy->control_dev, on); + } return 0; } -static int omap_usb_power_on(struct phy *x) +static int omap_usb_power_off(struct phy *x) { struct omap_usb *phy = phy_get_drvdata(x); - omap_control_phy_power(phy->control_dev, 1); + return omap_usb_phy_power(phy, false); +} - return 0; +static int omap_usb_power_on(struct phy *x) +{ + struct omap_usb *phy = phy_get_drvdata(x); + + return omap_usb_phy_power(phy, true); } static int omap_usb_init(struct phy *x) @@ -147,26 +192,31 @@ static struct phy_ops ops = { static const struct usb_phy_data omap_usb2_data = { .label = "omap_usb2", .flags = OMAP_USB2_HAS_START_SRP | OMAP_USB2_HAS_SET_VBUS, + .type = TYPE_USB2, }; static const struct usb_phy_data omap5_usb2_data = { .label = "omap5_usb2", .flags = 0, + .type = TYPE_USB2, }; static const struct usb_phy_data dra7x_usb2_data = { .label = "dra7x_usb2", .flags = OMAP_USB2_CALIBRATE_FALSE_DISCONNECT, + .type = TYPE_USB2, }; static const struct usb_phy_data dra7x_usb2_phy2_data = { .label = "dra7x_usb2_phy2", .flags = OMAP_USB2_CALIBRATE_FALSE_DISCONNECT, + .type = TYPE_DRA7USB2, }; static const struct usb_phy_data am437x_usb2_data = { .label = "am437x_usb2", .flags = 0, + .type = TYPE_AM437USB2, }; static const struct of_device_id omap_usb2_id_table[] = { @@ -223,6 +273,7 @@ static int omap_usb2_probe(struct platform_device *pdev) return -ENOMEM; phy->dev = &pdev->dev; + phy->type = phy_data->type; phy->phy.dev = phy->dev; phy->phy.label = phy_data->label; @@ -237,20 +288,36 @@ static int omap_usb2_probe(struct platform_device *pdev) phy->flags |= OMAP_USB2_CALIBRATE_FALSE_DISCONNECT; } - control_node = of_parse_phandle(node, "ctrl-module", 0); - if (!control_node) { - dev_err(&pdev->dev, "Failed to get control device phandle\n"); - return -EINVAL; - } + phy->syscon_phy_power = syscon_regmap_lookup_by_phandle(node, + "syscon-phy-power"); + if (IS_ERR(phy->syscon_phy_power)) { + dev_info(&pdev->dev, + "can't get syscon-phy-power, using control device\n"); + phy->syscon_phy_power = NULL; + + control_node = of_parse_phandle(node, "ctrl-module", 0); + if (!control_node) { + dev_err(&pdev->dev, + "Failed to get control device phandle\n"); + return -EINVAL; + } - control_pdev = of_find_device_by_node(control_node); - if (!control_pdev) { - dev_err(&pdev->dev, "Failed to get control device\n"); - return -EINVAL; + control_pdev = of_find_device_by_node(control_node); + if (!control_pdev) { + dev_err(&pdev->dev, "Failed to get control device\n"); + return -EINVAL; + } + phy->control_dev = &control_pdev->dev; + } else { + if (of_property_read_u32_index(node, + "syscon-phy-power", 1, + &phy->power_reg)) { + dev_err(&pdev->dev, + "couldn't get power reg. offset\n"); + return -EINVAL; + } } - phy->control_dev = &control_pdev->dev; - otg->set_host = omap_usb_set_host; otg->set_peripheral = omap_usb_set_peripheral; if (phy_data->flags & OMAP_USB2_HAS_SET_VBUS) diff --git a/include/linux/phy/omap_usb.h b/include/linux/phy/omap_usb.h index dc2c541..de933ab 100644 --- a/include/linux/phy/omap_usb.h +++ b/include/linux/phy/omap_usb.h @@ -30,6 +30,12 @@ struct usb_dpll_params { u32 mf; }; +enum omap_usb_phy_type { + TYPE_USB2, /* USB2_PHY, power down in CONTROL_DEV_CONF */ + TYPE_DRA7USB2, /* USB2 PHY, power and power_aux e.g. DRA7 */ + TYPE_AM437USB2, /* USB2 PHY, power e.g. AM437x */ +}; + struct omap_usb { struct usb_phy phy; struct phy_companion *comparator; @@ -40,11 +46,15 @@ struct omap_usb { struct clk *wkupclk; struct clk *optclk; u8 flags; + enum omap_usb_phy_type type; + struct regmap *syscon_phy_power; /* ctrl. reg. acces */ + unsigned int power_reg; /* power reg. index within syscon */ }; struct usb_phy_data { const char *label; u8 flags; + enum omap_usb_phy_type type; }; /* Driver Flags */ @@ -52,6 +62,14 @@ struct usb_phy_data { #define OMAP_USB2_HAS_SET_VBUS (1 << 1) #define OMAP_USB2_CALIBRATE_FALSE_DISCONNECT (1 << 2) +#define OMAP_DEV_PHY_PD BIT(0) +#define OMAP_USB2_PHY_PD BIT(28) + +#define AM437X_USB2_PHY_PD BIT(0) +#define AM437X_USB2_OTG_PD BIT(1) +#define AM437X_USB2_OTGVDET_EN BIT(19) +#define AM437X_USB2_OTGSESSEND_EN BIT(20) + #define phy_to_omapusb(x) container_of((x), struct omap_usb, phy) #if defined(CONFIG_OMAP_USB2) || defined(CONFIG_OMAP_USB2_MODULE)
Deprecate using phy-omap-control driver to power on/off the PHY, and use *syscon* framework to do the same. This handles powering on/off the PHY for the USB2 PHYs used in various TI SoCs. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> --- Documentation/devicetree/bindings/phy/ti-phy.txt | 6 +- drivers/phy/phy-omap-usb2.c | 101 ++++++++++++++++++---- include/linux/phy/omap_usb.h | 18 ++++ 3 files changed, 107 insertions(+), 18 deletions(-)