| Message ID | 1430761002-9327-5-git-send-email-abrestic@chromium.org |
|---|---|
| State | Needs Review / ACK, archived |
| Headers | show |
| Context | Check | Description |
|---|---|---|
| robh/checkpatch | warning | total: 1 errors, 0 warnings, 0 lines checked |
| robh/patch-applied | success |
On Mon, 04 May 2015, Andrew Bresticker wrote: > Add a binding document for the XUSB host complex on NVIDIA Tegra124 > and later SoCs. The XUSB host complex includes a mailbox for > communication with the XUSB micro-controller and an xHCI host-controller. > > Signed-off-by: Andrew Bresticker <abrestic@chromium.org> > Cc: Rob Herring <robh+dt@kernel.org> > Cc: Pawel Moll <pawel.moll@arm.com> > Cc: Mark Rutland <mark.rutland@arm.com> > Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> > Cc: Kumar Gala <galak@codeaurora.org> > Cc: Samuel Ortiz <sameo@linux.intel.com> > Cc: Lee Jones <lee.jones@linaro.org> > --- > Changes from v7: > - Move non-shared resources into child nodes. > New for v7. > --- > .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ > 1 file changed, 37 insertions(+) > create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > > diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > new file mode 100644 > index 0000000..bc50110 > --- /dev/null > +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > @@ -0,0 +1,37 @@ > +NVIDIA Tegra XUSB host copmlex > +============================== > + > +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host > +controller and a mailbox for communication with the XUSB micro-controller. > + > +Required properties: > +-------------------- > + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". > + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' > + where <chip> is tegra132. > + - reg: Must contain the base and length of the XUSB FPCI registers. > + - ranges: Bus address mapping for the XUSB block. Can be empty since the > + mapping is 1:1. > + - #address-cells: Must be 2. > + - #size-cells: Must be 2. > + > +Example: > +-------- > + usb@0,70098000 { > + compatible = "nvidia,tegra124-xusb"; > + reg = <0x0 0x70098000 0x0 0x1000>; > + ranges; > + > + #address-cells = <2>; > + #size-cells = <2>; > + > + usb-host@0,70090000 { > + compatible = "nvidia,tegra124-xhci"; > + ... > + }; > + > + mailbox { > + compatible = "nvidia,tegra124-xusb-mbox"; > + ... > + }; This doesn't appear to be a proper MFD. I would have the USB and Mailbox devices probe seperately and use a phandle to point the USB device to its Mailbox. usb@xyz { mboxes = <&xusb-mailbox, [chan]>; };
Lee, On Wed, May 13, 2015 at 7:39 AM, Lee Jones <lee.jones@linaro.org> wrote: > On Mon, 04 May 2015, Andrew Bresticker wrote: > >> Add a binding document for the XUSB host complex on NVIDIA Tegra124 >> and later SoCs. The XUSB host complex includes a mailbox for >> communication with the XUSB micro-controller and an xHCI host-controller. >> >> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> >> Cc: Rob Herring <robh+dt@kernel.org> >> Cc: Pawel Moll <pawel.moll@arm.com> >> Cc: Mark Rutland <mark.rutland@arm.com> >> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> >> Cc: Kumar Gala <galak@codeaurora.org> >> Cc: Samuel Ortiz <sameo@linux.intel.com> >> Cc: Lee Jones <lee.jones@linaro.org> >> --- >> Changes from v7: >> - Move non-shared resources into child nodes. >> New for v7. >> --- >> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ >> 1 file changed, 37 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >> >> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >> new file mode 100644 >> index 0000000..bc50110 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >> @@ -0,0 +1,37 @@ >> +NVIDIA Tegra XUSB host copmlex >> +============================== >> + >> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host >> +controller and a mailbox for communication with the XUSB micro-controller. >> + >> +Required properties: >> +-------------------- >> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". >> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' >> + where <chip> is tegra132. >> + - reg: Must contain the base and length of the XUSB FPCI registers. >> + - ranges: Bus address mapping for the XUSB block. Can be empty since the >> + mapping is 1:1. >> + - #address-cells: Must be 2. >> + - #size-cells: Must be 2. >> + >> +Example: >> +-------- >> + usb@0,70098000 { >> + compatible = "nvidia,tegra124-xusb"; >> + reg = <0x0 0x70098000 0x0 0x1000>; >> + ranges; >> + >> + #address-cells = <2>; >> + #size-cells = <2>; >> + >> + usb-host@0,70090000 { >> + compatible = "nvidia,tegra124-xhci"; >> + ... >> + }; >> + >> + mailbox { >> + compatible = "nvidia,tegra124-xusb-mbox"; >> + ... >> + }; > > This doesn't appear to be a proper MFD. I would have the USB and > Mailbox devices probe seperately and use a phandle to point the USB > device to its Mailbox. > > usb@xyz { > mboxes = <&xusb-mailbox, [chan]>; > }; Then what will set up the shared regmap? The point of using an MFD here was to share a register set with both the mailbox and xHCI drivers and avoid having to map the same register set twice in two separate drivers. Thanks, Andrew -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Wed, 13 May 2015, Andrew Bresticker wrote: > Lee, > > On Wed, May 13, 2015 at 7:39 AM, Lee Jones <lee.jones@linaro.org> wrote: > > On Mon, 04 May 2015, Andrew Bresticker wrote: > > > >> Add a binding document for the XUSB host complex on NVIDIA Tegra124 > >> and later SoCs. The XUSB host complex includes a mailbox for > >> communication with the XUSB micro-controller and an xHCI host-controller. > >> > >> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> > >> Cc: Rob Herring <robh+dt@kernel.org> > >> Cc: Pawel Moll <pawel.moll@arm.com> > >> Cc: Mark Rutland <mark.rutland@arm.com> > >> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> > >> Cc: Kumar Gala <galak@codeaurora.org> > >> Cc: Samuel Ortiz <sameo@linux.intel.com> > >> Cc: Lee Jones <lee.jones@linaro.org> > >> --- > >> Changes from v7: > >> - Move non-shared resources into child nodes. > >> New for v7. > >> --- > >> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ > >> 1 file changed, 37 insertions(+) > >> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >> > >> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >> new file mode 100644 > >> index 0000000..bc50110 > >> --- /dev/null > >> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >> @@ -0,0 +1,37 @@ > >> +NVIDIA Tegra XUSB host copmlex > >> +============================== > >> + > >> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host > >> +controller and a mailbox for communication with the XUSB micro-controller. > >> + > >> +Required properties: > >> +-------------------- > >> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". > >> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' > >> + where <chip> is tegra132. > >> + - reg: Must contain the base and length of the XUSB FPCI registers. > >> + - ranges: Bus address mapping for the XUSB block. Can be empty since the > >> + mapping is 1:1. > >> + - #address-cells: Must be 2. > >> + - #size-cells: Must be 2. > >> + > >> +Example: > >> +-------- > >> + usb@0,70098000 { > >> + compatible = "nvidia,tegra124-xusb"; > >> + reg = <0x0 0x70098000 0x0 0x1000>; > >> + ranges; > >> + > >> + #address-cells = <2>; > >> + #size-cells = <2>; > >> + > >> + usb-host@0,70090000 { > >> + compatible = "nvidia,tegra124-xhci"; > >> + ... > >> + }; > >> + > >> + mailbox { > >> + compatible = "nvidia,tegra124-xusb-mbox"; > >> + ... > >> + }; > > > > This doesn't appear to be a proper MFD. I would have the USB and > > Mailbox devices probe seperately and use a phandle to point the USB > > device to its Mailbox. > > > > usb@xyz { > > mboxes = <&xusb-mailbox, [chan]>; > > }; > > Then what will set up the shared regmap? The point of using an MFD > here was to share a register set with both the mailbox and xHCI > drivers and avoid having to map the same register set twice in two > separate drivers. Can you share the mapping please?
On Wed, May 13, 2015 at 9:50 AM, Lee Jones <lee.jones@linaro.org> wrote: > On Wed, 13 May 2015, Andrew Bresticker wrote: > >> Lee, >> >> On Wed, May 13, 2015 at 7:39 AM, Lee Jones <lee.jones@linaro.org> wrote: >> > On Mon, 04 May 2015, Andrew Bresticker wrote: >> > >> >> Add a binding document for the XUSB host complex on NVIDIA Tegra124 >> >> and later SoCs. The XUSB host complex includes a mailbox for >> >> communication with the XUSB micro-controller and an xHCI host-controller. >> >> >> >> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> >> >> Cc: Rob Herring <robh+dt@kernel.org> >> >> Cc: Pawel Moll <pawel.moll@arm.com> >> >> Cc: Mark Rutland <mark.rutland@arm.com> >> >> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> >> >> Cc: Kumar Gala <galak@codeaurora.org> >> >> Cc: Samuel Ortiz <sameo@linux.intel.com> >> >> Cc: Lee Jones <lee.jones@linaro.org> >> >> --- >> >> Changes from v7: >> >> - Move non-shared resources into child nodes. >> >> New for v7. >> >> --- >> >> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ >> >> 1 file changed, 37 insertions(+) >> >> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >> >> >> >> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >> >> new file mode 100644 >> >> index 0000000..bc50110 >> >> --- /dev/null >> >> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >> >> @@ -0,0 +1,37 @@ >> >> +NVIDIA Tegra XUSB host copmlex >> >> +============================== >> >> + >> >> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host >> >> +controller and a mailbox for communication with the XUSB micro-controller. >> >> + >> >> +Required properties: >> >> +-------------------- >> >> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". >> >> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' >> >> + where <chip> is tegra132. >> >> + - reg: Must contain the base and length of the XUSB FPCI registers. >> >> + - ranges: Bus address mapping for the XUSB block. Can be empty since the >> >> + mapping is 1:1. >> >> + - #address-cells: Must be 2. >> >> + - #size-cells: Must be 2. >> >> + >> >> +Example: >> >> +-------- >> >> + usb@0,70098000 { >> >> + compatible = "nvidia,tegra124-xusb"; >> >> + reg = <0x0 0x70098000 0x0 0x1000>; >> >> + ranges; >> >> + >> >> + #address-cells = <2>; >> >> + #size-cells = <2>; >> >> + >> >> + usb-host@0,70090000 { >> >> + compatible = "nvidia,tegra124-xhci"; >> >> + ... >> >> + }; >> >> + >> >> + mailbox { >> >> + compatible = "nvidia,tegra124-xusb-mbox"; >> >> + ... >> >> + }; >> > >> > This doesn't appear to be a proper MFD. I would have the USB and >> > Mailbox devices probe seperately and use a phandle to point the USB >> > device to its Mailbox. >> > >> > usb@xyz { >> > mboxes = <&xusb-mailbox, [chan]>; >> > }; >> >> Then what will set up the shared regmap? The point of using an MFD >> here was to share a register set with both the mailbox and xHCI >> drivers and avoid having to map the same register set twice in two >> separate drivers. > > Can you share the mapping please? What do you mean? That's what the MFD is doing now by setting up an MMIO regmap to be shared between the two devices. Thanks, Andrew -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Lee, On 13/05/15 15:39, Lee Jones wrote: > On Mon, 04 May 2015, Andrew Bresticker wrote: > >> Add a binding document for the XUSB host complex on NVIDIA Tegra124 >> and later SoCs. The XUSB host complex includes a mailbox for >> communication with the XUSB micro-controller and an xHCI host-controller. >> >> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> >> Cc: Rob Herring <robh+dt@kernel.org> >> Cc: Pawel Moll <pawel.moll@arm.com> >> Cc: Mark Rutland <mark.rutland@arm.com> >> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> >> Cc: Kumar Gala <galak@codeaurora.org> >> Cc: Samuel Ortiz <sameo@linux.intel.com> >> Cc: Lee Jones <lee.jones@linaro.org> >> --- >> Changes from v7: >> - Move non-shared resources into child nodes. >> New for v7. >> --- >> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ >> 1 file changed, 37 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >> >> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >> new file mode 100644 >> index 0000000..bc50110 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >> @@ -0,0 +1,37 @@ >> +NVIDIA Tegra XUSB host copmlex >> +============================== >> + >> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host >> +controller and a mailbox for communication with the XUSB micro-controller. >> + >> +Required properties: >> +-------------------- >> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". >> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' >> + where <chip> is tegra132. >> + - reg: Must contain the base and length of the XUSB FPCI registers. >> + - ranges: Bus address mapping for the XUSB block. Can be empty since the >> + mapping is 1:1. >> + - #address-cells: Must be 2. >> + - #size-cells: Must be 2. >> + >> +Example: >> +-------- >> + usb@0,70098000 { >> + compatible = "nvidia,tegra124-xusb"; >> + reg = <0x0 0x70098000 0x0 0x1000>; >> + ranges; >> + >> + #address-cells = <2>; >> + #size-cells = <2>; >> + >> + usb-host@0,70090000 { >> + compatible = "nvidia,tegra124-xhci"; >> + ... >> + }; >> + >> + mailbox { >> + compatible = "nvidia,tegra124-xusb-mbox"; >> + ... >> + }; > > This doesn't appear to be a proper MFD. I would have the USB and > Mailbox devices probe seperately and use a phandle to point the USB > device to its Mailbox. > > usb@xyz { > mboxes = <&xusb-mailbox, [chan]>; > }; > I am assuming that Andrew had laid it out like this to reflect the hw structure. The mailbox and xhci controller are part of the xusb sub-system and hence appear as child nodes. My understanding is that for device-tree we want the device-tree structure to reflect the actual hw. Is this not the case? Cheers Jon -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Wed, 13 May 2015, Andrew Bresticker wrote: > On Wed, May 13, 2015 at 9:50 AM, Lee Jones <lee.jones@linaro.org> wrote: > > On Wed, 13 May 2015, Andrew Bresticker wrote: > > > >> Lee, > >> > >> On Wed, May 13, 2015 at 7:39 AM, Lee Jones <lee.jones@linaro.org> wrote: > >> > On Mon, 04 May 2015, Andrew Bresticker wrote: > >> > > >> >> Add a binding document for the XUSB host complex on NVIDIA Tegra124 > >> >> and later SoCs. The XUSB host complex includes a mailbox for > >> >> communication with the XUSB micro-controller and an xHCI host-controller. > >> >> > >> >> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> > >> >> Cc: Rob Herring <robh+dt@kernel.org> > >> >> Cc: Pawel Moll <pawel.moll@arm.com> > >> >> Cc: Mark Rutland <mark.rutland@arm.com> > >> >> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> > >> >> Cc: Kumar Gala <galak@codeaurora.org> > >> >> Cc: Samuel Ortiz <sameo@linux.intel.com> > >> >> Cc: Lee Jones <lee.jones@linaro.org> > >> >> --- > >> >> Changes from v7: > >> >> - Move non-shared resources into child nodes. > >> >> New for v7. > >> >> --- > >> >> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ > >> >> 1 file changed, 37 insertions(+) > >> >> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >> >> > >> >> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >> >> new file mode 100644 > >> >> index 0000000..bc50110 > >> >> --- /dev/null > >> >> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >> >> @@ -0,0 +1,37 @@ > >> >> +NVIDIA Tegra XUSB host copmlex > >> >> +============================== > >> >> + > >> >> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host > >> >> +controller and a mailbox for communication with the XUSB micro-controller. > >> >> + > >> >> +Required properties: > >> >> +-------------------- > >> >> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". > >> >> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' > >> >> + where <chip> is tegra132. > >> >> + - reg: Must contain the base and length of the XUSB FPCI registers. > >> >> + - ranges: Bus address mapping for the XUSB block. Can be empty since the > >> >> + mapping is 1:1. > >> >> + - #address-cells: Must be 2. > >> >> + - #size-cells: Must be 2. > >> >> + > >> >> +Example: > >> >> +-------- > >> >> + usb@0,70098000 { > >> >> + compatible = "nvidia,tegra124-xusb"; > >> >> + reg = <0x0 0x70098000 0x0 0x1000>; > >> >> + ranges; > >> >> + > >> >> + #address-cells = <2>; > >> >> + #size-cells = <2>; > >> >> + > >> >> + usb-host@0,70090000 { > >> >> + compatible = "nvidia,tegra124-xhci"; > >> >> + ... > >> >> + }; > >> >> + > >> >> + mailbox { > >> >> + compatible = "nvidia,tegra124-xusb-mbox"; > >> >> + ... > >> >> + }; > >> > > >> > This doesn't appear to be a proper MFD. I would have the USB and > >> > Mailbox devices probe seperately and use a phandle to point the USB > >> > device to its Mailbox. > >> > > >> > usb@xyz { > >> > mboxes = <&xusb-mailbox, [chan]>; > >> > }; > >> > >> Then what will set up the shared regmap? The point of using an MFD > >> here was to share a register set with both the mailbox and xHCI > >> drivers and avoid having to map the same register set twice in two > >> separate drivers. > > > > Can you share the mapping please? > > What do you mean? That's what the MFD is doing now by setting up an > MMIO regmap to be shared between the two devices. I mean, can you share the documentation with me. :)
On 14/05/15 08:29, Lee Jones wrote: > On Wed, 13 May 2015, Andrew Bresticker wrote: > >> On Wed, May 13, 2015 at 9:50 AM, Lee Jones <lee.jones@linaro.org> wrote: >>> On Wed, 13 May 2015, Andrew Bresticker wrote: >>> >>>> Lee, >>>> >>>> On Wed, May 13, 2015 at 7:39 AM, Lee Jones <lee.jones@linaro.org> wrote: >>>>> On Mon, 04 May 2015, Andrew Bresticker wrote: >>>>> >>>>>> Add a binding document for the XUSB host complex on NVIDIA Tegra124 >>>>>> and later SoCs. The XUSB host complex includes a mailbox for >>>>>> communication with the XUSB micro-controller and an xHCI host-controller. >>>>>> >>>>>> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> >>>>>> Cc: Rob Herring <robh+dt@kernel.org> >>>>>> Cc: Pawel Moll <pawel.moll@arm.com> >>>>>> Cc: Mark Rutland <mark.rutland@arm.com> >>>>>> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> >>>>>> Cc: Kumar Gala <galak@codeaurora.org> >>>>>> Cc: Samuel Ortiz <sameo@linux.intel.com> >>>>>> Cc: Lee Jones <lee.jones@linaro.org> >>>>>> --- >>>>>> Changes from v7: >>>>>> - Move non-shared resources into child nodes. >>>>>> New for v7. >>>>>> --- >>>>>> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ >>>>>> 1 file changed, 37 insertions(+) >>>>>> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >>>>>> >>>>>> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >>>>>> new file mode 100644 >>>>>> index 0000000..bc50110 >>>>>> --- /dev/null >>>>>> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >>>>>> @@ -0,0 +1,37 @@ >>>>>> +NVIDIA Tegra XUSB host copmlex >>>>>> +============================== >>>>>> + >>>>>> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host >>>>>> +controller and a mailbox for communication with the XUSB micro-controller. >>>>>> + >>>>>> +Required properties: >>>>>> +-------------------- >>>>>> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". >>>>>> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' >>>>>> + where <chip> is tegra132. >>>>>> + - reg: Must contain the base and length of the XUSB FPCI registers. >>>>>> + - ranges: Bus address mapping for the XUSB block. Can be empty since the >>>>>> + mapping is 1:1. >>>>>> + - #address-cells: Must be 2. >>>>>> + - #size-cells: Must be 2. >>>>>> + >>>>>> +Example: >>>>>> +-------- >>>>>> + usb@0,70098000 { >>>>>> + compatible = "nvidia,tegra124-xusb"; >>>>>> + reg = <0x0 0x70098000 0x0 0x1000>; >>>>>> + ranges; >>>>>> + >>>>>> + #address-cells = <2>; >>>>>> + #size-cells = <2>; >>>>>> + >>>>>> + usb-host@0,70090000 { >>>>>> + compatible = "nvidia,tegra124-xhci"; >>>>>> + ... >>>>>> + }; >>>>>> + >>>>>> + mailbox { >>>>>> + compatible = "nvidia,tegra124-xusb-mbox"; >>>>>> + ... >>>>>> + }; >>>>> >>>>> This doesn't appear to be a proper MFD. I would have the USB and >>>>> Mailbox devices probe seperately and use a phandle to point the USB >>>>> device to its Mailbox. >>>>> >>>>> usb@xyz { >>>>> mboxes = <&xusb-mailbox, [chan]>; >>>>> }; >>>> >>>> Then what will set up the shared regmap? The point of using an MFD >>>> here was to share a register set with both the mailbox and xHCI >>>> drivers and avoid having to map the same register set twice in two >>>> separate drivers. >>> >>> Can you share the mapping please? >> >> What do you mean? That's what the MFD is doing now by setting up an >> MMIO regmap to be shared between the two devices. > > I mean, can you share the documentation with me. :) You can download the documentation from here [1]. See chapter 19 USB complex. However, I will warn you that unfortunately, you need to sign up for an account :-( Cheers Jon [1] https://developer.nvidia.com/tegra-k1-technical-reference-manual -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Thu, 14 May 2015, Jon Hunter wrote: > Hi Lee, > > On 13/05/15 15:39, Lee Jones wrote: > > On Mon, 04 May 2015, Andrew Bresticker wrote: > > > >> Add a binding document for the XUSB host complex on NVIDIA Tegra124 > >> and later SoCs. The XUSB host complex includes a mailbox for > >> communication with the XUSB micro-controller and an xHCI host-controller. > >> > >> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> > >> Cc: Rob Herring <robh+dt@kernel.org> > >> Cc: Pawel Moll <pawel.moll@arm.com> > >> Cc: Mark Rutland <mark.rutland@arm.com> > >> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> > >> Cc: Kumar Gala <galak@codeaurora.org> > >> Cc: Samuel Ortiz <sameo@linux.intel.com> > >> Cc: Lee Jones <lee.jones@linaro.org> > >> --- > >> Changes from v7: > >> - Move non-shared resources into child nodes. > >> New for v7. > >> --- > >> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ > >> 1 file changed, 37 insertions(+) > >> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >> > >> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >> new file mode 100644 > >> index 0000000..bc50110 > >> --- /dev/null > >> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >> @@ -0,0 +1,37 @@ > >> +NVIDIA Tegra XUSB host copmlex > >> +============================== > >> + > >> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host > >> +controller and a mailbox for communication with the XUSB micro-controller. > >> + > >> +Required properties: > >> +-------------------- > >> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". > >> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' > >> + where <chip> is tegra132. > >> + - reg: Must contain the base and length of the XUSB FPCI registers. > >> + - ranges: Bus address mapping for the XUSB block. Can be empty since the > >> + mapping is 1:1. > >> + - #address-cells: Must be 2. > >> + - #size-cells: Must be 2. > >> + > >> +Example: > >> +-------- > >> + usb@0,70098000 { > >> + compatible = "nvidia,tegra124-xusb"; > >> + reg = <0x0 0x70098000 0x0 0x1000>; > >> + ranges; > >> + > >> + #address-cells = <2>; > >> + #size-cells = <2>; > >> + > >> + usb-host@0,70090000 { > >> + compatible = "nvidia,tegra124-xhci"; > >> + ... > >> + }; > >> + > >> + mailbox { > >> + compatible = "nvidia,tegra124-xusb-mbox"; > >> + ... > >> + }; > > > > This doesn't appear to be a proper MFD. I would have the USB and > > Mailbox devices probe seperately and use a phandle to point the USB > > device to its Mailbox. > > > > usb@xyz { > > mboxes = <&xusb-mailbox, [chan]>; > > }; > > > > I am assuming that Andrew had laid it out like this to reflect the hw > structure. The mailbox and xhci controller are part of the xusb > sub-system and hence appear as child nodes. My understanding is that for > device-tree we want the device-tree structure to reflect the actual hw. > Is this not the case? Yes, the DT files should reflect h/w. I have requested to see what the memory map looks like, so I might provide a more appropriate solution to accepting a pretty pointless MFD. Two solutions spring to mind. You can either call of_platform_populate() from the USB driver, as some already do: drivers/usb/dwc3/dwc3-exynos.c: ret = of_platform_populate(node, NULL, NULL, dev); drivers/usb/dwc3/dwc3-keystone.c: error = of_platform_populate(node, NULL, NULL, dev); drivers/usb/dwc3/dwc3-omap.c: ret = of_platform_populate(node, NULL, NULL, dev); drivers/usb/dwc3/dwc3-qcom.c: ret = of_platform_populate(node, NULL, NULL, qdwc->dev); drivers/usb/dwc3/dwc3-st.c: ret = of_platform_populate(node, NULL, NULL, dev); drivers/usb/musb/musb_am335x.c: ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev); Or use the "simple-mfd", which is currently in -next: git show next/master:Documentation/devicetree/bindings/mfd/mfd.txt
On Thu, 14 May 2015, Jon Hunter wrote: > > On 14/05/15 08:29, Lee Jones wrote: > > On Wed, 13 May 2015, Andrew Bresticker wrote: > > > >> On Wed, May 13, 2015 at 9:50 AM, Lee Jones <lee.jones@linaro.org> wrote: > >>> On Wed, 13 May 2015, Andrew Bresticker wrote: > >>> > >>>> Lee, > >>>> > >>>> On Wed, May 13, 2015 at 7:39 AM, Lee Jones <lee.jones@linaro.org> wrote: > >>>>> On Mon, 04 May 2015, Andrew Bresticker wrote: > >>>>> > >>>>>> Add a binding document for the XUSB host complex on NVIDIA Tegra124 > >>>>>> and later SoCs. The XUSB host complex includes a mailbox for > >>>>>> communication with the XUSB micro-controller and an xHCI host-controller. > >>>>>> > >>>>>> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> > >>>>>> Cc: Rob Herring <robh+dt@kernel.org> > >>>>>> Cc: Pawel Moll <pawel.moll@arm.com> > >>>>>> Cc: Mark Rutland <mark.rutland@arm.com> > >>>>>> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> > >>>>>> Cc: Kumar Gala <galak@codeaurora.org> > >>>>>> Cc: Samuel Ortiz <sameo@linux.intel.com> > >>>>>> Cc: Lee Jones <lee.jones@linaro.org> > >>>>>> --- > >>>>>> Changes from v7: > >>>>>> - Move non-shared resources into child nodes. > >>>>>> New for v7. > >>>>>> --- > >>>>>> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ > >>>>>> 1 file changed, 37 insertions(+) > >>>>>> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >>>>>> > >>>>>> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >>>>>> new file mode 100644 > >>>>>> index 0000000..bc50110 > >>>>>> --- /dev/null > >>>>>> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >>>>>> @@ -0,0 +1,37 @@ > >>>>>> +NVIDIA Tegra XUSB host copmlex > >>>>>> +============================== > >>>>>> + > >>>>>> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host > >>>>>> +controller and a mailbox for communication with the XUSB micro-controller. > >>>>>> + > >>>>>> +Required properties: > >>>>>> +-------------------- > >>>>>> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". > >>>>>> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' > >>>>>> + where <chip> is tegra132. > >>>>>> + - reg: Must contain the base and length of the XUSB FPCI registers. > >>>>>> + - ranges: Bus address mapping for the XUSB block. Can be empty since the > >>>>>> + mapping is 1:1. > >>>>>> + - #address-cells: Must be 2. > >>>>>> + - #size-cells: Must be 2. > >>>>>> + > >>>>>> +Example: > >>>>>> +-------- > >>>>>> + usb@0,70098000 { > >>>>>> + compatible = "nvidia,tegra124-xusb"; > >>>>>> + reg = <0x0 0x70098000 0x0 0x1000>; > >>>>>> + ranges; > >>>>>> + > >>>>>> + #address-cells = <2>; > >>>>>> + #size-cells = <2>; > >>>>>> + > >>>>>> + usb-host@0,70090000 { > >>>>>> + compatible = "nvidia,tegra124-xhci"; > >>>>>> + ... > >>>>>> + }; > >>>>>> + > >>>>>> + mailbox { > >>>>>> + compatible = "nvidia,tegra124-xusb-mbox"; > >>>>>> + ... > >>>>>> + }; > >>>>> > >>>>> This doesn't appear to be a proper MFD. I would have the USB and > >>>>> Mailbox devices probe seperately and use a phandle to point the USB > >>>>> device to its Mailbox. > >>>>> > >>>>> usb@xyz { > >>>>> mboxes = <&xusb-mailbox, [chan]>; > >>>>> }; > >>>> > >>>> Then what will set up the shared regmap? The point of using an MFD > >>>> here was to share a register set with both the mailbox and xHCI > >>>> drivers and avoid having to map the same register set twice in two > >>>> separate drivers. > >>> > >>> Can you share the mapping please? > >> > >> What do you mean? That's what the MFD is doing now by setting up an > >> MMIO regmap to be shared between the two devices. > > > > I mean, can you share the documentation with me. :) > > You can download the documentation from here [1]. See chapter 19 USB > complex. However, I will warn you that unfortunately, you need to sign > up for an account :-( I'll give that a miss for the time being. See my other mail for now.
On 14/05/15 08:40, Lee Jones wrote: > On Thu, 14 May 2015, Jon Hunter wrote: > >> Hi Lee, >> >> On 13/05/15 15:39, Lee Jones wrote: >>> On Mon, 04 May 2015, Andrew Bresticker wrote: >>> >>>> Add a binding document for the XUSB host complex on NVIDIA Tegra124 >>>> and later SoCs. The XUSB host complex includes a mailbox for >>>> communication with the XUSB micro-controller and an xHCI host-controller. >>>> >>>> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> >>>> Cc: Rob Herring <robh+dt@kernel.org> >>>> Cc: Pawel Moll <pawel.moll@arm.com> >>>> Cc: Mark Rutland <mark.rutland@arm.com> >>>> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> >>>> Cc: Kumar Gala <galak@codeaurora.org> >>>> Cc: Samuel Ortiz <sameo@linux.intel.com> >>>> Cc: Lee Jones <lee.jones@linaro.org> >>>> --- >>>> Changes from v7: >>>> - Move non-shared resources into child nodes. >>>> New for v7. >>>> --- >>>> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ >>>> 1 file changed, 37 insertions(+) >>>> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >>>> >>>> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >>>> new file mode 100644 >>>> index 0000000..bc50110 >>>> --- /dev/null >>>> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >>>> @@ -0,0 +1,37 @@ >>>> +NVIDIA Tegra XUSB host copmlex >>>> +============================== >>>> + >>>> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host >>>> +controller and a mailbox for communication with the XUSB micro-controller. >>>> + >>>> +Required properties: >>>> +-------------------- >>>> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". >>>> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' >>>> + where <chip> is tegra132. >>>> + - reg: Must contain the base and length of the XUSB FPCI registers. >>>> + - ranges: Bus address mapping for the XUSB block. Can be empty since the >>>> + mapping is 1:1. >>>> + - #address-cells: Must be 2. >>>> + - #size-cells: Must be 2. >>>> + >>>> +Example: >>>> +-------- >>>> + usb@0,70098000 { >>>> + compatible = "nvidia,tegra124-xusb"; >>>> + reg = <0x0 0x70098000 0x0 0x1000>; >>>> + ranges; >>>> + >>>> + #address-cells = <2>; >>>> + #size-cells = <2>; >>>> + >>>> + usb-host@0,70090000 { >>>> + compatible = "nvidia,tegra124-xhci"; >>>> + ... >>>> + }; >>>> + >>>> + mailbox { >>>> + compatible = "nvidia,tegra124-xusb-mbox"; >>>> + ... >>>> + }; >>> >>> This doesn't appear to be a proper MFD. I would have the USB and >>> Mailbox devices probe seperately and use a phandle to point the USB >>> device to its Mailbox. >>> >>> usb@xyz { >>> mboxes = <&xusb-mailbox, [chan]>; >>> }; >>> >> >> I am assuming that Andrew had laid it out like this to reflect the hw >> structure. The mailbox and xhci controller are part of the xusb >> sub-system and hence appear as child nodes. My understanding is that for >> device-tree we want the device-tree structure to reflect the actual hw. >> Is this not the case? > > Yes, the DT files should reflect h/w. I have requested to see what > the memory map looks like, so I might provide a more appropriate > solution to accepting a pretty pointless MFD. For the xusb-host has memory from 0x7009000 - 0x7009ffff. Within this range, we have this fpci range which is defined as 0x7009800 - 0x70098fff. This range is being shared between the mailbox and xhci drivers. Looking at the drivers, we have ... mailbox uses: 0x700980e0 - 0x700980f3 and 0x70098428 - 0x7009842b. xhci uses: 0x70098000 - 0x700980cf and 0x70098800 - 0x70098803. So it is a bit messy as they overlap. However, we could have ... xusb_mbox: mailbox { compatible = "nvidia,tegra124-xusb-mbox"; reg = <0x0 0x700980e0 0x0 0x14>, <0x0 0x70098428 0x0 0x4>; ... }; usb-host@0,70090000 { compatible = "nvidia,tegra124-xhci"; reg = <0x0 0x70090000 0x0 0x8000>, <0x0 0x70098000 0x0 0x00d0>; <0x0 0x70098800 0x0 0x0004>; <0x0 0x70099000 0x0 0x1000>; ... }; I believe that Thierry and Stephen said that they wished to avoid multiple devices sharing the same memory ranges, and so we would need to divvy up the memory map as above. However, I am not sure if this is an ok thing to do. > Two solutions spring to mind. You can either call > of_platform_populate() from the USB driver, as some already do: > > drivers/usb/dwc3/dwc3-exynos.c: > ret = of_platform_populate(node, NULL, NULL, dev); > drivers/usb/dwc3/dwc3-keystone.c: > error = of_platform_populate(node, NULL, NULL, dev); > drivers/usb/dwc3/dwc3-omap.c: > ret = of_platform_populate(node, NULL, NULL, dev); > drivers/usb/dwc3/dwc3-qcom.c: > ret = of_platform_populate(node, NULL, NULL, qdwc->dev); > drivers/usb/dwc3/dwc3-st.c: > ret = of_platform_populate(node, NULL, NULL, dev); > drivers/usb/musb/musb_am335x.c: > ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev); > > Or use the "simple-mfd", which is currently in -next: > > git show next/master:Documentation/devicetree/bindings/mfd/mfd.txt That is nice. Sounds like the "simple-bus" style of device but for an mfd. Based upon the above, let me know if you think we could use the "simple-mfd"? Cheers Jon -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Thu, 14 May 2015, Jon Hunter wrote: > On 14/05/15 08:40, Lee Jones wrote: > > On Thu, 14 May 2015, Jon Hunter wrote: > >> On 13/05/15 15:39, Lee Jones wrote: > >>> On Mon, 04 May 2015, Andrew Bresticker wrote: > >>> > >>>> Add a binding document for the XUSB host complex on NVIDIA Tegra124 > >>>> and later SoCs. The XUSB host complex includes a mailbox for > >>>> communication with the XUSB micro-controller and an xHCI host-controller. > >>>> > >>>> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> > >>>> Cc: Rob Herring <robh+dt@kernel.org> > >>>> Cc: Pawel Moll <pawel.moll@arm.com> > >>>> Cc: Mark Rutland <mark.rutland@arm.com> > >>>> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> > >>>> Cc: Kumar Gala <galak@codeaurora.org> > >>>> Cc: Samuel Ortiz <sameo@linux.intel.com> > >>>> Cc: Lee Jones <lee.jones@linaro.org> > >>>> --- > >>>> Changes from v7: > >>>> - Move non-shared resources into child nodes. > >>>> New for v7. > >>>> --- > >>>> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ > >>>> 1 file changed, 37 insertions(+) > >>>> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >>>> > >>>> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >>>> new file mode 100644 > >>>> index 0000000..bc50110 > >>>> --- /dev/null > >>>> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >>>> @@ -0,0 +1,37 @@ > >>>> +NVIDIA Tegra XUSB host copmlex > >>>> +============================== > >>>> + > >>>> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host > >>>> +controller and a mailbox for communication with the XUSB micro-controller. > >>>> + > >>>> +Required properties: > >>>> +-------------------- > >>>> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". > >>>> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' > >>>> + where <chip> is tegra132. > >>>> + - reg: Must contain the base and length of the XUSB FPCI registers. > >>>> + - ranges: Bus address mapping for the XUSB block. Can be empty since the > >>>> + mapping is 1:1. > >>>> + - #address-cells: Must be 2. > >>>> + - #size-cells: Must be 2. > >>>> + > >>>> +Example: > >>>> +-------- > >>>> + usb@0,70098000 { > >>>> + compatible = "nvidia,tegra124-xusb"; > >>>> + reg = <0x0 0x70098000 0x0 0x1000>; > >>>> + ranges; > >>>> + > >>>> + #address-cells = <2>; > >>>> + #size-cells = <2>; > >>>> + > >>>> + usb-host@0,70090000 { > >>>> + compatible = "nvidia,tegra124-xhci"; > >>>> + ... > >>>> + }; > >>>> + > >>>> + mailbox { > >>>> + compatible = "nvidia,tegra124-xusb-mbox"; > >>>> + ... > >>>> + }; > >>> > >>> This doesn't appear to be a proper MFD. I would have the USB and > >>> Mailbox devices probe seperately and use a phandle to point the USB > >>> device to its Mailbox. > >>> > >>> usb@xyz { > >>> mboxes = <&xusb-mailbox, [chan]>; > >>> }; > >>> > >> > >> I am assuming that Andrew had laid it out like this to reflect the hw > >> structure. The mailbox and xhci controller are part of the xusb > >> sub-system and hence appear as child nodes. My understanding is that for > >> device-tree we want the device-tree structure to reflect the actual hw. > >> Is this not the case? > > > > Yes, the DT files should reflect h/w. I have requested to see what > > the memory map looks like, so I might provide a more appropriate > > solution to accepting a pretty pointless MFD. > > For the xusb-host has memory from 0x7009000 - 0x7009ffff. > > Within this range, we have this fpci range which is defined as 0x7009800 > - 0x70098fff. This range is being shared between the mailbox and xhci > drivers. Looking at the drivers, we have ... > > mailbox uses: 0x700980e0 - 0x700980f3 and 0x70098428 - 0x7009842b. > xhci uses: 0x70098000 - 0x700980cf and 0x70098800 - 0x70098803. > > So it is a bit messy as they overlap. However, we could have ... > > xusb_mbox: mailbox { > compatible = "nvidia,tegra124-xusb-mbox"; > reg = <0x0 0x700980e0 0x0 0x14>, > <0x0 0x70098428 0x0 0x4>; > ... > }; > usb-host@0,70090000 { > compatible = "nvidia,tegra124-xhci"; > reg = <0x0 0x70090000 0x0 0x8000>, > <0x0 0x70098000 0x0 0x00d0>; > <0x0 0x70098800 0x0 0x0004>; > <0x0 0x70099000 0x0 0x1000>; > ... > }; > > I believe that Thierry and Stephen said that they wished to avoid > multiple devices sharing the same memory ranges, and so we would need to > divvy up the memory map as above. However, I am not sure if this is an > ok thing to do. > > > Two solutions spring to mind. You can either call > > of_platform_populate() from the USB driver, as some already do: > > > > drivers/usb/dwc3/dwc3-exynos.c: > > ret = of_platform_populate(node, NULL, NULL, dev); > > drivers/usb/dwc3/dwc3-keystone.c: > > error = of_platform_populate(node, NULL, NULL, dev); > > drivers/usb/dwc3/dwc3-omap.c: > > ret = of_platform_populate(node, NULL, NULL, dev); > > drivers/usb/dwc3/dwc3-qcom.c: > > ret = of_platform_populate(node, NULL, NULL, qdwc->dev); > > drivers/usb/dwc3/dwc3-st.c: > > ret = of_platform_populate(node, NULL, NULL, dev); > > drivers/usb/musb/musb_am335x.c: > > ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev); > > > > Or use the "simple-mfd", which is currently in -next: > > > > git show next/master:Documentation/devicetree/bindings/mfd/mfd.txt > > That is nice. Sounds like the "simple-bus" style of device but for an That's precisely what it does. FYI: You 'can' use "simple-bus" and it will do the right thing, but as an MFD isn't really a bus, it was decided to create something a little more fitting. > mfd. Based upon the above, let me know if you think we could use the > "simple-mfd"? I do. :)
On 14/05/15 10:30, Lee Jones wrote: > On Thu, 14 May 2015, Jon Hunter wrote: >> On 14/05/15 08:40, Lee Jones wrote: >>> On Thu, 14 May 2015, Jon Hunter wrote: >>>> On 13/05/15 15:39, Lee Jones wrote: >>>>> On Mon, 04 May 2015, Andrew Bresticker wrote: >>>>> >>>>>> Add a binding document for the XUSB host complex on NVIDIA Tegra124 >>>>>> and later SoCs. The XUSB host complex includes a mailbox for >>>>>> communication with the XUSB micro-controller and an xHCI host-controller. >>>>>> >>>>>> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> >>>>>> Cc: Rob Herring <robh+dt@kernel.org> >>>>>> Cc: Pawel Moll <pawel.moll@arm.com> >>>>>> Cc: Mark Rutland <mark.rutland@arm.com> >>>>>> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> >>>>>> Cc: Kumar Gala <galak@codeaurora.org> >>>>>> Cc: Samuel Ortiz <sameo@linux.intel.com> >>>>>> Cc: Lee Jones <lee.jones@linaro.org> >>>>>> --- >>>>>> Changes from v7: >>>>>> - Move non-shared resources into child nodes. >>>>>> New for v7. >>>>>> --- >>>>>> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ >>>>>> 1 file changed, 37 insertions(+) >>>>>> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >>>>>> >>>>>> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >>>>>> new file mode 100644 >>>>>> index 0000000..bc50110 >>>>>> --- /dev/null >>>>>> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >>>>>> @@ -0,0 +1,37 @@ >>>>>> +NVIDIA Tegra XUSB host copmlex >>>>>> +============================== >>>>>> + >>>>>> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host >>>>>> +controller and a mailbox for communication with the XUSB micro-controller. >>>>>> + >>>>>> +Required properties: >>>>>> +-------------------- >>>>>> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". >>>>>> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' >>>>>> + where <chip> is tegra132. >>>>>> + - reg: Must contain the base and length of the XUSB FPCI registers. >>>>>> + - ranges: Bus address mapping for the XUSB block. Can be empty since the >>>>>> + mapping is 1:1. >>>>>> + - #address-cells: Must be 2. >>>>>> + - #size-cells: Must be 2. >>>>>> + >>>>>> +Example: >>>>>> +-------- >>>>>> + usb@0,70098000 { >>>>>> + compatible = "nvidia,tegra124-xusb"; >>>>>> + reg = <0x0 0x70098000 0x0 0x1000>; >>>>>> + ranges; >>>>>> + >>>>>> + #address-cells = <2>; >>>>>> + #size-cells = <2>; >>>>>> + >>>>>> + usb-host@0,70090000 { >>>>>> + compatible = "nvidia,tegra124-xhci"; >>>>>> + ... >>>>>> + }; >>>>>> + >>>>>> + mailbox { >>>>>> + compatible = "nvidia,tegra124-xusb-mbox"; >>>>>> + ... >>>>>> + }; >>>>> >>>>> This doesn't appear to be a proper MFD. I would have the USB and >>>>> Mailbox devices probe seperately and use a phandle to point the USB >>>>> device to its Mailbox. >>>>> >>>>> usb@xyz { >>>>> mboxes = <&xusb-mailbox, [chan]>; >>>>> }; >>>>> >>>> >>>> I am assuming that Andrew had laid it out like this to reflect the hw >>>> structure. The mailbox and xhci controller are part of the xusb >>>> sub-system and hence appear as child nodes. My understanding is that for >>>> device-tree we want the device-tree structure to reflect the actual hw. >>>> Is this not the case? >>> >>> Yes, the DT files should reflect h/w. I have requested to see what >>> the memory map looks like, so I might provide a more appropriate >>> solution to accepting a pretty pointless MFD. >> >> For the xusb-host has memory from 0x7009000 - 0x7009ffff. >> >> Within this range, we have this fpci range which is defined as 0x7009800 >> - 0x70098fff. This range is being shared between the mailbox and xhci >> drivers. Looking at the drivers, we have ... >> >> mailbox uses: 0x700980e0 - 0x700980f3 and 0x70098428 - 0x7009842b. >> xhci uses: 0x70098000 - 0x700980cf and 0x70098800 - 0x70098803. >> >> So it is a bit messy as they overlap. However, we could have ... >> >> xusb_mbox: mailbox { >> compatible = "nvidia,tegra124-xusb-mbox"; >> reg = <0x0 0x700980e0 0x0 0x14>, >> <0x0 0x70098428 0x0 0x4>; >> ... >> }; >> usb-host@0,70090000 { >> compatible = "nvidia,tegra124-xhci"; >> reg = <0x0 0x70090000 0x0 0x8000>, >> <0x0 0x70098000 0x0 0x00d0>; >> <0x0 0x70098800 0x0 0x0004>; >> <0x0 0x70099000 0x0 0x1000>; >> ... >> }; >> >> I believe that Thierry and Stephen said that they wished to avoid >> multiple devices sharing the same memory ranges, and so we would need to >> divvy up the memory map as above. However, I am not sure if this is an >> ok thing to do. >> >>> Two solutions spring to mind. You can either call >>> of_platform_populate() from the USB driver, as some already do: >>> >>> drivers/usb/dwc3/dwc3-exynos.c: >>> ret = of_platform_populate(node, NULL, NULL, dev); >>> drivers/usb/dwc3/dwc3-keystone.c: >>> error = of_platform_populate(node, NULL, NULL, dev); >>> drivers/usb/dwc3/dwc3-omap.c: >>> ret = of_platform_populate(node, NULL, NULL, dev); >>> drivers/usb/dwc3/dwc3-qcom.c: >>> ret = of_platform_populate(node, NULL, NULL, qdwc->dev); >>> drivers/usb/dwc3/dwc3-st.c: >>> ret = of_platform_populate(node, NULL, NULL, dev); >>> drivers/usb/musb/musb_am335x.c: >>> ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev); >>> >>> Or use the "simple-mfd", which is currently in -next: >>> >>> git show next/master:Documentation/devicetree/bindings/mfd/mfd.txt >> >> That is nice. Sounds like the "simple-bus" style of device but for an > > That's precisely what it does. FYI: You 'can' use "simple-bus" and it > will do the right thing, but as an MFD isn't really a bus, it was > decided to create something a little more fitting. > >> mfd. Based upon the above, let me know if you think we could use the >> "simple-mfd"? > > I do. :) Thanks Lee. Thierry, any objections on the above mem-mapping? Cheers Jon -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Thu, 14 May 2015, Jon Hunter wrote: > On 14/05/15 10:30, Lee Jones wrote: > > On Thu, 14 May 2015, Jon Hunter wrote: > >> On 14/05/15 08:40, Lee Jones wrote: > >>> On Thu, 14 May 2015, Jon Hunter wrote: > >>>> On 13/05/15 15:39, Lee Jones wrote: > >>>>> On Mon, 04 May 2015, Andrew Bresticker wrote: > >>>>> > >>>>>> Add a binding document for the XUSB host complex on NVIDIA Tegra124 > >>>>>> and later SoCs. The XUSB host complex includes a mailbox for > >>>>>> communication with the XUSB micro-controller and an xHCI host-controller. > >>>>>> > >>>>>> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> > >>>>>> Cc: Rob Herring <robh+dt@kernel.org> > >>>>>> Cc: Pawel Moll <pawel.moll@arm.com> > >>>>>> Cc: Mark Rutland <mark.rutland@arm.com> > >>>>>> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> > >>>>>> Cc: Kumar Gala <galak@codeaurora.org> > >>>>>> Cc: Samuel Ortiz <sameo@linux.intel.com> > >>>>>> Cc: Lee Jones <lee.jones@linaro.org> > >>>>>> --- > >>>>>> Changes from v7: > >>>>>> - Move non-shared resources into child nodes. > >>>>>> New for v7. > >>>>>> --- > >>>>>> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ > >>>>>> 1 file changed, 37 insertions(+) > >>>>>> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >>>>>> > >>>>>> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >>>>>> new file mode 100644 > >>>>>> index 0000000..bc50110 > >>>>>> --- /dev/null > >>>>>> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >>>>>> @@ -0,0 +1,37 @@ > >>>>>> +NVIDIA Tegra XUSB host copmlex > >>>>>> +============================== > >>>>>> + > >>>>>> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host > >>>>>> +controller and a mailbox for communication with the XUSB micro-controller. > >>>>>> + > >>>>>> +Required properties: > >>>>>> +-------------------- > >>>>>> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". > >>>>>> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' > >>>>>> + where <chip> is tegra132. > >>>>>> + - reg: Must contain the base and length of the XUSB FPCI registers. > >>>>>> + - ranges: Bus address mapping for the XUSB block. Can be empty since the > >>>>>> + mapping is 1:1. > >>>>>> + - #address-cells: Must be 2. > >>>>>> + - #size-cells: Must be 2. > >>>>>> + > >>>>>> +Example: > >>>>>> +-------- > >>>>>> + usb@0,70098000 { > >>>>>> + compatible = "nvidia,tegra124-xusb"; > >>>>>> + reg = <0x0 0x70098000 0x0 0x1000>; > >>>>>> + ranges; > >>>>>> + > >>>>>> + #address-cells = <2>; > >>>>>> + #size-cells = <2>; > >>>>>> + > >>>>>> + usb-host@0,70090000 { > >>>>>> + compatible = "nvidia,tegra124-xhci"; > >>>>>> + ... > >>>>>> + }; > >>>>>> + > >>>>>> + mailbox { > >>>>>> + compatible = "nvidia,tegra124-xusb-mbox"; > >>>>>> + ... > >>>>>> + }; > >>>>> > >>>>> This doesn't appear to be a proper MFD. I would have the USB and > >>>>> Mailbox devices probe seperately and use a phandle to point the USB > >>>>> device to its Mailbox. > >>>>> > >>>>> usb@xyz { > >>>>> mboxes = <&xusb-mailbox, [chan]>; > >>>>> }; > >>>>> > >>>> > >>>> I am assuming that Andrew had laid it out like this to reflect the hw > >>>> structure. The mailbox and xhci controller are part of the xusb > >>>> sub-system and hence appear as child nodes. My understanding is that for > >>>> device-tree we want the device-tree structure to reflect the actual hw. > >>>> Is this not the case? > >>> > >>> Yes, the DT files should reflect h/w. I have requested to see what > >>> the memory map looks like, so I might provide a more appropriate > >>> solution to accepting a pretty pointless MFD. > >> > >> For the xusb-host has memory from 0x7009000 - 0x7009ffff. > >> > >> Within this range, we have this fpci range which is defined as 0x7009800 > >> - 0x70098fff. This range is being shared between the mailbox and xhci > >> drivers. Looking at the drivers, we have ... > >> > >> mailbox uses: 0x700980e0 - 0x700980f3 and 0x70098428 - 0x7009842b. > >> xhci uses: 0x70098000 - 0x700980cf and 0x70098800 - 0x70098803. > >> > >> So it is a bit messy as they overlap. However, we could have ... > >> > >> xusb_mbox: mailbox { > >> compatible = "nvidia,tegra124-xusb-mbox"; > >> reg = <0x0 0x700980e0 0x0 0x14>, > >> <0x0 0x70098428 0x0 0x4>; > >> ... > >> }; > >> usb-host@0,70090000 { > >> compatible = "nvidia,tegra124-xhci"; > >> reg = <0x0 0x70090000 0x0 0x8000>, > >> <0x0 0x70098000 0x0 0x00d0>; > >> <0x0 0x70098800 0x0 0x0004>; > >> <0x0 0x70099000 0x0 0x1000>; > >> ... > >> }; > >> > >> I believe that Thierry and Stephen said that they wished to avoid > >> multiple devices sharing the same memory ranges, and so we would need to > >> divvy up the memory map as above. However, I am not sure if this is an > >> ok thing to do. > >> > >>> Two solutions spring to mind. You can either call > >>> of_platform_populate() from the USB driver, as some already do: > >>> > >>> drivers/usb/dwc3/dwc3-exynos.c: > >>> ret = of_platform_populate(node, NULL, NULL, dev); > >>> drivers/usb/dwc3/dwc3-keystone.c: > >>> error = of_platform_populate(node, NULL, NULL, dev); > >>> drivers/usb/dwc3/dwc3-omap.c: > >>> ret = of_platform_populate(node, NULL, NULL, dev); > >>> drivers/usb/dwc3/dwc3-qcom.c: > >>> ret = of_platform_populate(node, NULL, NULL, qdwc->dev); > >>> drivers/usb/dwc3/dwc3-st.c: > >>> ret = of_platform_populate(node, NULL, NULL, dev); > >>> drivers/usb/musb/musb_am335x.c: > >>> ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev); > >>> > >>> Or use the "simple-mfd", which is currently in -next: > >>> > >>> git show next/master:Documentation/devicetree/bindings/mfd/mfd.txt > >> > >> That is nice. Sounds like the "simple-bus" style of device but for an > > > > That's precisely what it does. FYI: You 'can' use "simple-bus" and it > > will do the right thing, but as an MFD isn't really a bus, it was > > decided to create something a little more fitting. > > > >> mfd. Based upon the above, let me know if you think we could use the > >> "simple-mfd"? > > > > I do. :) > > Thanks Lee. > > Thierry, any objections on the above mem-mapping? If you have the mailbox as the child device and use "simple-mfd", you don't need to slice up the memory do you?
On 14/05/15 11:23, Lee Jones wrote: > On Thu, 14 May 2015, Jon Hunter wrote: >> On 14/05/15 10:30, Lee Jones wrote: >>> On Thu, 14 May 2015, Jon Hunter wrote: >>>> On 14/05/15 08:40, Lee Jones wrote: >>>>> On Thu, 14 May 2015, Jon Hunter wrote: >>>>>> On 13/05/15 15:39, Lee Jones wrote: >>>>>>> On Mon, 04 May 2015, Andrew Bresticker wrote: >>>>>>> >>>>>>>> Add a binding document for the XUSB host complex on NVIDIA Tegra124 >>>>>>>> and later SoCs. The XUSB host complex includes a mailbox for >>>>>>>> communication with the XUSB micro-controller and an xHCI host-controller. >>>>>>>> >>>>>>>> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> >>>>>>>> Cc: Rob Herring <robh+dt@kernel.org> >>>>>>>> Cc: Pawel Moll <pawel.moll@arm.com> >>>>>>>> Cc: Mark Rutland <mark.rutland@arm.com> >>>>>>>> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> >>>>>>>> Cc: Kumar Gala <galak@codeaurora.org> >>>>>>>> Cc: Samuel Ortiz <sameo@linux.intel.com> >>>>>>>> Cc: Lee Jones <lee.jones@linaro.org> >>>>>>>> --- >>>>>>>> Changes from v7: >>>>>>>> - Move non-shared resources into child nodes. >>>>>>>> New for v7. >>>>>>>> --- >>>>>>>> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ >>>>>>>> 1 file changed, 37 insertions(+) >>>>>>>> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >>>>>>>> >>>>>>>> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >>>>>>>> new file mode 100644 >>>>>>>> index 0000000..bc50110 >>>>>>>> --- /dev/null >>>>>>>> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >>>>>>>> @@ -0,0 +1,37 @@ >>>>>>>> +NVIDIA Tegra XUSB host copmlex >>>>>>>> +============================== >>>>>>>> + >>>>>>>> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host >>>>>>>> +controller and a mailbox for communication with the XUSB micro-controller. >>>>>>>> + >>>>>>>> +Required properties: >>>>>>>> +-------------------- >>>>>>>> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". >>>>>>>> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' >>>>>>>> + where <chip> is tegra132. >>>>>>>> + - reg: Must contain the base and length of the XUSB FPCI registers. >>>>>>>> + - ranges: Bus address mapping for the XUSB block. Can be empty since the >>>>>>>> + mapping is 1:1. >>>>>>>> + - #address-cells: Must be 2. >>>>>>>> + - #size-cells: Must be 2. >>>>>>>> + >>>>>>>> +Example: >>>>>>>> +-------- >>>>>>>> + usb@0,70098000 { >>>>>>>> + compatible = "nvidia,tegra124-xusb"; >>>>>>>> + reg = <0x0 0x70098000 0x0 0x1000>; >>>>>>>> + ranges; >>>>>>>> + >>>>>>>> + #address-cells = <2>; >>>>>>>> + #size-cells = <2>; >>>>>>>> + >>>>>>>> + usb-host@0,70090000 { >>>>>>>> + compatible = "nvidia,tegra124-xhci"; >>>>>>>> + ... >>>>>>>> + }; >>>>>>>> + >>>>>>>> + mailbox { >>>>>>>> + compatible = "nvidia,tegra124-xusb-mbox"; >>>>>>>> + ... >>>>>>>> + }; >>>>>>> >>>>>>> This doesn't appear to be a proper MFD. I would have the USB and >>>>>>> Mailbox devices probe seperately and use a phandle to point the USB >>>>>>> device to its Mailbox. >>>>>>> >>>>>>> usb@xyz { >>>>>>> mboxes = <&xusb-mailbox, [chan]>; >>>>>>> }; >>>>>>> >>>>>> >>>>>> I am assuming that Andrew had laid it out like this to reflect the hw >>>>>> structure. The mailbox and xhci controller are part of the xusb >>>>>> sub-system and hence appear as child nodes. My understanding is that for >>>>>> device-tree we want the device-tree structure to reflect the actual hw. >>>>>> Is this not the case? >>>>> >>>>> Yes, the DT files should reflect h/w. I have requested to see what >>>>> the memory map looks like, so I might provide a more appropriate >>>>> solution to accepting a pretty pointless MFD. >>>> >>>> For the xusb-host has memory from 0x7009000 - 0x7009ffff. >>>> >>>> Within this range, we have this fpci range which is defined as 0x7009800 >>>> - 0x70098fff. This range is being shared between the mailbox and xhci >>>> drivers. Looking at the drivers, we have ... >>>> >>>> mailbox uses: 0x700980e0 - 0x700980f3 and 0x70098428 - 0x7009842b. >>>> xhci uses: 0x70098000 - 0x700980cf and 0x70098800 - 0x70098803. >>>> >>>> So it is a bit messy as they overlap. However, we could have ... >>>> >>>> xusb_mbox: mailbox { >>>> compatible = "nvidia,tegra124-xusb-mbox"; >>>> reg = <0x0 0x700980e0 0x0 0x14>, >>>> <0x0 0x70098428 0x0 0x4>; >>>> ... >>>> }; >>>> usb-host@0,70090000 { >>>> compatible = "nvidia,tegra124-xhci"; >>>> reg = <0x0 0x70090000 0x0 0x8000>, >>>> <0x0 0x70098000 0x0 0x00d0>; >>>> <0x0 0x70098800 0x0 0x0004>; >>>> <0x0 0x70099000 0x0 0x1000>; >>>> ... >>>> }; >>>> >>>> I believe that Thierry and Stephen said that they wished to avoid >>>> multiple devices sharing the same memory ranges, and so we would need to >>>> divvy up the memory map as above. However, I am not sure if this is an >>>> ok thing to do. >>>> >>>>> Two solutions spring to mind. You can either call >>>>> of_platform_populate() from the USB driver, as some already do: >>>>> >>>>> drivers/usb/dwc3/dwc3-exynos.c: >>>>> ret = of_platform_populate(node, NULL, NULL, dev); >>>>> drivers/usb/dwc3/dwc3-keystone.c: >>>>> error = of_platform_populate(node, NULL, NULL, dev); >>>>> drivers/usb/dwc3/dwc3-omap.c: >>>>> ret = of_platform_populate(node, NULL, NULL, dev); >>>>> drivers/usb/dwc3/dwc3-qcom.c: >>>>> ret = of_platform_populate(node, NULL, NULL, qdwc->dev); >>>>> drivers/usb/dwc3/dwc3-st.c: >>>>> ret = of_platform_populate(node, NULL, NULL, dev); >>>>> drivers/usb/musb/musb_am335x.c: >>>>> ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev); >>>>> >>>>> Or use the "simple-mfd", which is currently in -next: >>>>> >>>>> git show next/master:Documentation/devicetree/bindings/mfd/mfd.txt >>>> >>>> That is nice. Sounds like the "simple-bus" style of device but for an >>> >>> That's precisely what it does. FYI: You 'can' use "simple-bus" and it >>> will do the right thing, but as an MFD isn't really a bus, it was >>> decided to create something a little more fitting. >>> >>>> mfd. Based upon the above, let me know if you think we could use the >>>> "simple-mfd"? >>> >>> I do. :) >> >> Thanks Lee. >> >> Thierry, any objections on the above mem-mapping? > > If you have the mailbox as the child device and use "simple-mfd", you > don't need to slice up the memory do you? Ok, I see what you are saying and I know that was what Andrew was doing in this patch (just not with the "simple-mfd"). Cheers Jon -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Thu, May 14, 2015 at 12:40 AM, Lee Jones <lee.jones@linaro.org> wrote: > On Thu, 14 May 2015, Jon Hunter wrote: > >> Hi Lee, >> >> On 13/05/15 15:39, Lee Jones wrote: >> > On Mon, 04 May 2015, Andrew Bresticker wrote: >> > >> >> Add a binding document for the XUSB host complex on NVIDIA Tegra124 >> >> and later SoCs. The XUSB host complex includes a mailbox for >> >> communication with the XUSB micro-controller and an xHCI host-controller. >> >> >> >> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> >> >> Cc: Rob Herring <robh+dt@kernel.org> >> >> Cc: Pawel Moll <pawel.moll@arm.com> >> >> Cc: Mark Rutland <mark.rutland@arm.com> >> >> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> >> >> Cc: Kumar Gala <galak@codeaurora.org> >> >> Cc: Samuel Ortiz <sameo@linux.intel.com> >> >> Cc: Lee Jones <lee.jones@linaro.org> >> >> --- >> >> Changes from v7: >> >> - Move non-shared resources into child nodes. >> >> New for v7. >> >> --- >> >> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ >> >> 1 file changed, 37 insertions(+) >> >> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >> >> >> >> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >> >> new file mode 100644 >> >> index 0000000..bc50110 >> >> --- /dev/null >> >> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >> >> @@ -0,0 +1,37 @@ >> >> +NVIDIA Tegra XUSB host copmlex >> >> +============================== >> >> + >> >> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host >> >> +controller and a mailbox for communication with the XUSB micro-controller. >> >> + >> >> +Required properties: >> >> +-------------------- >> >> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". >> >> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' >> >> + where <chip> is tegra132. >> >> + - reg: Must contain the base and length of the XUSB FPCI registers. >> >> + - ranges: Bus address mapping for the XUSB block. Can be empty since the >> >> + mapping is 1:1. >> >> + - #address-cells: Must be 2. >> >> + - #size-cells: Must be 2. >> >> + >> >> +Example: >> >> +-------- >> >> + usb@0,70098000 { >> >> + compatible = "nvidia,tegra124-xusb"; >> >> + reg = <0x0 0x70098000 0x0 0x1000>; >> >> + ranges; >> >> + >> >> + #address-cells = <2>; >> >> + #size-cells = <2>; >> >> + >> >> + usb-host@0,70090000 { >> >> + compatible = "nvidia,tegra124-xhci"; >> >> + ... >> >> + }; >> >> + >> >> + mailbox { >> >> + compatible = "nvidia,tegra124-xusb-mbox"; >> >> + ... >> >> + }; >> > >> > This doesn't appear to be a proper MFD. I would have the USB and >> > Mailbox devices probe seperately and use a phandle to point the USB >> > device to its Mailbox. >> > >> > usb@xyz { >> > mboxes = <&xusb-mailbox, [chan]>; >> > }; >> > >> >> I am assuming that Andrew had laid it out like this to reflect the hw >> structure. The mailbox and xhci controller are part of the xusb >> sub-system and hence appear as child nodes. My understanding is that for >> device-tree we want the device-tree structure to reflect the actual hw. >> Is this not the case? > > Yes, the DT files should reflect h/w. I have requested to see what > the memory map looks like, so I might provide a more appropriate > solution to accepting a pretty pointless MFD. FWIW, the address map for XUSB looks like this: XUSB_HOST: 0x70090000 - 0x7009a000 xHCI registers: 0x70090000 - 0x70098000 FPCI configuration registers: 0x70098000 - 0x70099000 IPFS configuration registers: 0x70099000 - 0x7009a000 > Two solutions spring to mind. You can either call > of_platform_populate() from the USB driver, as some already do: > > drivers/usb/dwc3/dwc3-exynos.c: > ret = of_platform_populate(node, NULL, NULL, dev); > drivers/usb/dwc3/dwc3-keystone.c: > error = of_platform_populate(node, NULL, NULL, dev); > drivers/usb/dwc3/dwc3-omap.c: > ret = of_platform_populate(node, NULL, NULL, dev); > drivers/usb/dwc3/dwc3-qcom.c: > ret = of_platform_populate(node, NULL, NULL, qdwc->dev); > drivers/usb/dwc3/dwc3-st.c: > ret = of_platform_populate(node, NULL, NULL, dev); > drivers/usb/musb/musb_am335x.c: > ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev); This still requires a small, separate driver to setup the regmap and do of_platform_populate(). The only difference is it lives in drivers/usb/ instead of drivers/mfd/. > Or use the "simple-mfd", which is currently in -next: > > git show next/master:Documentation/devicetree/bindings/mfd/mfd.txt I'm not too opposed to this, but Thierry was when I brought this up before. The issue here is that if we ever have to do something besides setting up a regmap in the MFD, we'd have to change the binding and break DT backwards-compatibility. Thanks, Andrew -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Lee, On Thu, May 14, 2015 at 10:38 AM, Andrew Bresticker <abrestic@chromium.org> wrote: > On Thu, May 14, 2015 at 12:40 AM, Lee Jones <lee.jones@linaro.org> wrote: >> On Thu, 14 May 2015, Jon Hunter wrote: >> >>> Hi Lee, >>> >>> On 13/05/15 15:39, Lee Jones wrote: >>> > On Mon, 04 May 2015, Andrew Bresticker wrote: >>> > >>> >> Add a binding document for the XUSB host complex on NVIDIA Tegra124 >>> >> and later SoCs. The XUSB host complex includes a mailbox for >>> >> communication with the XUSB micro-controller and an xHCI host-controller. >>> >> >>> >> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> >>> >> Cc: Rob Herring <robh+dt@kernel.org> >>> >> Cc: Pawel Moll <pawel.moll@arm.com> >>> >> Cc: Mark Rutland <mark.rutland@arm.com> >>> >> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> >>> >> Cc: Kumar Gala <galak@codeaurora.org> >>> >> Cc: Samuel Ortiz <sameo@linux.intel.com> >>> >> Cc: Lee Jones <lee.jones@linaro.org> >>> >> --- >>> >> Changes from v7: >>> >> - Move non-shared resources into child nodes. >>> >> New for v7. >>> >> --- >>> >> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ >>> >> 1 file changed, 37 insertions(+) >>> >> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >>> >> >>> >> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >>> >> new file mode 100644 >>> >> index 0000000..bc50110 >>> >> --- /dev/null >>> >> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt >>> >> @@ -0,0 +1,37 @@ >>> >> +NVIDIA Tegra XUSB host copmlex >>> >> +============================== >>> >> + >>> >> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host >>> >> +controller and a mailbox for communication with the XUSB micro-controller. >>> >> + >>> >> +Required properties: >>> >> +-------------------- >>> >> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". >>> >> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' >>> >> + where <chip> is tegra132. >>> >> + - reg: Must contain the base and length of the XUSB FPCI registers. >>> >> + - ranges: Bus address mapping for the XUSB block. Can be empty since the >>> >> + mapping is 1:1. >>> >> + - #address-cells: Must be 2. >>> >> + - #size-cells: Must be 2. >>> >> + >>> >> +Example: >>> >> +-------- >>> >> + usb@0,70098000 { >>> >> + compatible = "nvidia,tegra124-xusb"; >>> >> + reg = <0x0 0x70098000 0x0 0x1000>; >>> >> + ranges; >>> >> + >>> >> + #address-cells = <2>; >>> >> + #size-cells = <2>; >>> >> + >>> >> + usb-host@0,70090000 { >>> >> + compatible = "nvidia,tegra124-xhci"; >>> >> + ... >>> >> + }; >>> >> + >>> >> + mailbox { >>> >> + compatible = "nvidia,tegra124-xusb-mbox"; >>> >> + ... >>> >> + }; >>> > >>> > This doesn't appear to be a proper MFD. I would have the USB and >>> > Mailbox devices probe seperately and use a phandle to point the USB >>> > device to its Mailbox. >>> > >>> > usb@xyz { >>> > mboxes = <&xusb-mailbox, [chan]>; >>> > }; >>> > >>> >>> I am assuming that Andrew had laid it out like this to reflect the hw >>> structure. The mailbox and xhci controller are part of the xusb >>> sub-system and hence appear as child nodes. My understanding is that for >>> device-tree we want the device-tree structure to reflect the actual hw. >>> Is this not the case? >> >> Yes, the DT files should reflect h/w. I have requested to see what >> the memory map looks like, so I might provide a more appropriate >> solution to accepting a pretty pointless MFD. > > FWIW, the address map for XUSB looks like this: > > XUSB_HOST: 0x70090000 - 0x7009a000 > xHCI registers: 0x70090000 - 0x70098000 > FPCI configuration registers: 0x70098000 - 0x70099000 > IPFS configuration registers: 0x70099000 - 0x7009a000 > >> Two solutions spring to mind. You can either call >> of_platform_populate() from the USB driver, as some already do: >> >> drivers/usb/dwc3/dwc3-exynos.c: >> ret = of_platform_populate(node, NULL, NULL, dev); >> drivers/usb/dwc3/dwc3-keystone.c: >> error = of_platform_populate(node, NULL, NULL, dev); >> drivers/usb/dwc3/dwc3-omap.c: >> ret = of_platform_populate(node, NULL, NULL, dev); >> drivers/usb/dwc3/dwc3-qcom.c: >> ret = of_platform_populate(node, NULL, NULL, qdwc->dev); >> drivers/usb/dwc3/dwc3-st.c: >> ret = of_platform_populate(node, NULL, NULL, dev); >> drivers/usb/musb/musb_am335x.c: >> ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev); > > This still requires a small, separate driver to setup the regmap and > do of_platform_populate(). The only difference is it lives in > drivers/usb/ instead of drivers/mfd/. > >> Or use the "simple-mfd", which is currently in -next: >> >> git show next/master:Documentation/devicetree/bindings/mfd/mfd.txt > > I'm not too opposed to this, but Thierry was when I brought this up > before. The issue here is that if we ever have to do something > besides setting up a regmap in the MFD, we'd have to change the > binding and break DT backwards-compatibility. Any thoughts on this? A minimal MFD seems to be the best way to future-proof this binding/driver should it need to be extended in the future. If this is a firm NAK from you however, I'll need to let Jassi now so that he can un-queue the mailbox patches for 4.2.... Thanks, Andrew -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Tue, 19 May 2015, Andrew Bresticker wrote: > Lee, > > On Thu, May 14, 2015 at 10:38 AM, Andrew Bresticker > <abrestic@chromium.org> wrote: > > On Thu, May 14, 2015 at 12:40 AM, Lee Jones <lee.jones@linaro.org> wrote: > >> On Thu, 14 May 2015, Jon Hunter wrote: > >> > >>> Hi Lee, > >>> > >>> On 13/05/15 15:39, Lee Jones wrote: > >>> > On Mon, 04 May 2015, Andrew Bresticker wrote: > >>> > > >>> >> Add a binding document for the XUSB host complex on NVIDIA Tegra124 > >>> >> and later SoCs. The XUSB host complex includes a mailbox for > >>> >> communication with the XUSB micro-controller and an xHCI host-controller. > >>> >> > >>> >> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> > >>> >> Cc: Rob Herring <robh+dt@kernel.org> > >>> >> Cc: Pawel Moll <pawel.moll@arm.com> > >>> >> Cc: Mark Rutland <mark.rutland@arm.com> > >>> >> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> > >>> >> Cc: Kumar Gala <galak@codeaurora.org> > >>> >> Cc: Samuel Ortiz <sameo@linux.intel.com> > >>> >> Cc: Lee Jones <lee.jones@linaro.org> > >>> >> --- > >>> >> Changes from v7: > >>> >> - Move non-shared resources into child nodes. > >>> >> New for v7. > >>> >> --- > >>> >> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ > >>> >> 1 file changed, 37 insertions(+) > >>> >> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >>> >> > >>> >> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >>> >> new file mode 100644 > >>> >> index 0000000..bc50110 > >>> >> --- /dev/null > >>> >> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > >>> >> @@ -0,0 +1,37 @@ > >>> >> +NVIDIA Tegra XUSB host copmlex > >>> >> +============================== > >>> >> + > >>> >> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host > >>> >> +controller and a mailbox for communication with the XUSB micro-controller. > >>> >> + > >>> >> +Required properties: > >>> >> +-------------------- > >>> >> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". > >>> >> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' > >>> >> + where <chip> is tegra132. > >>> >> + - reg: Must contain the base and length of the XUSB FPCI registers. > >>> >> + - ranges: Bus address mapping for the XUSB block. Can be empty since the > >>> >> + mapping is 1:1. > >>> >> + - #address-cells: Must be 2. > >>> >> + - #size-cells: Must be 2. > >>> >> + > >>> >> +Example: > >>> >> +-------- > >>> >> + usb@0,70098000 { > >>> >> + compatible = "nvidia,tegra124-xusb"; > >>> >> + reg = <0x0 0x70098000 0x0 0x1000>; > >>> >> + ranges; > >>> >> + > >>> >> + #address-cells = <2>; > >>> >> + #size-cells = <2>; > >>> >> + > >>> >> + usb-host@0,70090000 { > >>> >> + compatible = "nvidia,tegra124-xhci"; > >>> >> + ... > >>> >> + }; > >>> >> + > >>> >> + mailbox { > >>> >> + compatible = "nvidia,tegra124-xusb-mbox"; > >>> >> + ... > >>> >> + }; > >>> > > >>> > This doesn't appear to be a proper MFD. I would have the USB and > >>> > Mailbox devices probe seperately and use a phandle to point the USB > >>> > device to its Mailbox. > >>> > > >>> > usb@xyz { > >>> > mboxes = <&xusb-mailbox, [chan]>; > >>> > }; > >>> > > >>> > >>> I am assuming that Andrew had laid it out like this to reflect the hw > >>> structure. The mailbox and xhci controller are part of the xusb > >>> sub-system and hence appear as child nodes. My understanding is that for > >>> device-tree we want the device-tree structure to reflect the actual hw. > >>> Is this not the case? > >> > >> Yes, the DT files should reflect h/w. I have requested to see what > >> the memory map looks like, so I might provide a more appropriate > >> solution to accepting a pretty pointless MFD. > > > > FWIW, the address map for XUSB looks like this: > > > > XUSB_HOST: 0x70090000 - 0x7009a000 > > xHCI registers: 0x70090000 - 0x70098000 > > FPCI configuration registers: 0x70098000 - 0x70099000 > > IPFS configuration registers: 0x70099000 - 0x7009a000 > > > >> Two solutions spring to mind. You can either call > >> of_platform_populate() from the USB driver, as some already do: > >> > >> drivers/usb/dwc3/dwc3-exynos.c: > >> ret = of_platform_populate(node, NULL, NULL, dev); > >> drivers/usb/dwc3/dwc3-keystone.c: > >> error = of_platform_populate(node, NULL, NULL, dev); > >> drivers/usb/dwc3/dwc3-omap.c: > >> ret = of_platform_populate(node, NULL, NULL, dev); > >> drivers/usb/dwc3/dwc3-qcom.c: > >> ret = of_platform_populate(node, NULL, NULL, qdwc->dev); > >> drivers/usb/dwc3/dwc3-st.c: > >> ret = of_platform_populate(node, NULL, NULL, dev); > >> drivers/usb/musb/musb_am335x.c: > >> ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev); > > > > This still requires a small, separate driver to setup the regmap and > > do of_platform_populate(). The only difference is it lives in > > drivers/usb/ instead of drivers/mfd/. > > > >> Or use the "simple-mfd", which is currently in -next: > >> > >> git show next/master:Documentation/devicetree/bindings/mfd/mfd.txt > > > > I'm not too opposed to this, but Thierry was when I brought this up > > before. The issue here is that if we ever have to do something > > besides setting up a regmap in the MFD, we'd have to change the > > binding and break DT backwards-compatibility. > > Any thoughts on this? A minimal MFD seems to be the best way to > future-proof this binding/driver should it need to be extended in the > future. If this is a firm NAK from you however, I'll need to let > Jassi now so that he can un-queue the mailbox patches for 4.2.... I was waiting to hear Thierry's thoughts. However, I am unconvinced that you need an MFD driver for this and refuse to take a shell (read "pointless") one on an "if we ever ..." clause. Will you break backwards capability though? I'm not sure you will. Old DTBs will still use 'simple-mfd' and probe the devices in the normal way. *If* you introduce an MFD driver at a later date then the old DTB will miss out the *new* functionality, which is expected and accepted.
On Wed, May 20, 2015 at 07:35:51AM +0100, Lee Jones wrote: > On Tue, 19 May 2015, Andrew Bresticker wrote: > > > Lee, > > > > On Thu, May 14, 2015 at 10:38 AM, Andrew Bresticker > > <abrestic@chromium.org> wrote: > > > On Thu, May 14, 2015 at 12:40 AM, Lee Jones <lee.jones@linaro.org> wrote: > > >> On Thu, 14 May 2015, Jon Hunter wrote: > > >> > > >>> Hi Lee, > > >>> > > >>> On 13/05/15 15:39, Lee Jones wrote: > > >>> > On Mon, 04 May 2015, Andrew Bresticker wrote: > > >>> > > > >>> >> Add a binding document for the XUSB host complex on NVIDIA Tegra124 > > >>> >> and later SoCs. The XUSB host complex includes a mailbox for > > >>> >> communication with the XUSB micro-controller and an xHCI host-controller. > > >>> >> > > >>> >> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> > > >>> >> Cc: Rob Herring <robh+dt@kernel.org> > > >>> >> Cc: Pawel Moll <pawel.moll@arm.com> > > >>> >> Cc: Mark Rutland <mark.rutland@arm.com> > > >>> >> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> > > >>> >> Cc: Kumar Gala <galak@codeaurora.org> > > >>> >> Cc: Samuel Ortiz <sameo@linux.intel.com> > > >>> >> Cc: Lee Jones <lee.jones@linaro.org> > > >>> >> --- > > >>> >> Changes from v7: > > >>> >> - Move non-shared resources into child nodes. > > >>> >> New for v7. > > >>> >> --- > > >>> >> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ > > >>> >> 1 file changed, 37 insertions(+) > > >>> >> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > > >>> >> > > >>> >> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > > >>> >> new file mode 100644 > > >>> >> index 0000000..bc50110 > > >>> >> --- /dev/null > > >>> >> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > > >>> >> @@ -0,0 +1,37 @@ > > >>> >> +NVIDIA Tegra XUSB host copmlex > > >>> >> +============================== > > >>> >> + > > >>> >> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host > > >>> >> +controller and a mailbox for communication with the XUSB micro-controller. > > >>> >> + > > >>> >> +Required properties: > > >>> >> +-------------------- > > >>> >> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". > > >>> >> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' > > >>> >> + where <chip> is tegra132. > > >>> >> + - reg: Must contain the base and length of the XUSB FPCI registers. > > >>> >> + - ranges: Bus address mapping for the XUSB block. Can be empty since the > > >>> >> + mapping is 1:1. > > >>> >> + - #address-cells: Must be 2. > > >>> >> + - #size-cells: Must be 2. > > >>> >> + > > >>> >> +Example: > > >>> >> +-------- > > >>> >> + usb@0,70098000 { > > >>> >> + compatible = "nvidia,tegra124-xusb"; > > >>> >> + reg = <0x0 0x70098000 0x0 0x1000>; > > >>> >> + ranges; > > >>> >> + > > >>> >> + #address-cells = <2>; > > >>> >> + #size-cells = <2>; > > >>> >> + > > >>> >> + usb-host@0,70090000 { > > >>> >> + compatible = "nvidia,tegra124-xhci"; > > >>> >> + ... > > >>> >> + }; > > >>> >> + > > >>> >> + mailbox { > > >>> >> + compatible = "nvidia,tegra124-xusb-mbox"; > > >>> >> + ... > > >>> >> + }; > > >>> > > > >>> > This doesn't appear to be a proper MFD. I would have the USB and > > >>> > Mailbox devices probe seperately and use a phandle to point the USB > > >>> > device to its Mailbox. > > >>> > > > >>> > usb@xyz { > > >>> > mboxes = <&xusb-mailbox, [chan]>; > > >>> > }; > > >>> > > > >>> > > >>> I am assuming that Andrew had laid it out like this to reflect the hw > > >>> structure. The mailbox and xhci controller are part of the xusb > > >>> sub-system and hence appear as child nodes. My understanding is that for > > >>> device-tree we want the device-tree structure to reflect the actual hw. > > >>> Is this not the case? > > >> > > >> Yes, the DT files should reflect h/w. I have requested to see what > > >> the memory map looks like, so I might provide a more appropriate > > >> solution to accepting a pretty pointless MFD. > > > > > > FWIW, the address map for XUSB looks like this: > > > > > > XUSB_HOST: 0x70090000 - 0x7009a000 > > > xHCI registers: 0x70090000 - 0x70098000 > > > FPCI configuration registers: 0x70098000 - 0x70099000 > > > IPFS configuration registers: 0x70099000 - 0x7009a000 > > > > > >> Two solutions spring to mind. You can either call > > >> of_platform_populate() from the USB driver, as some already do: > > >> > > >> drivers/usb/dwc3/dwc3-exynos.c: > > >> ret = of_platform_populate(node, NULL, NULL, dev); > > >> drivers/usb/dwc3/dwc3-keystone.c: > > >> error = of_platform_populate(node, NULL, NULL, dev); > > >> drivers/usb/dwc3/dwc3-omap.c: > > >> ret = of_platform_populate(node, NULL, NULL, dev); > > >> drivers/usb/dwc3/dwc3-qcom.c: > > >> ret = of_platform_populate(node, NULL, NULL, qdwc->dev); > > >> drivers/usb/dwc3/dwc3-st.c: > > >> ret = of_platform_populate(node, NULL, NULL, dev); > > >> drivers/usb/musb/musb_am335x.c: > > >> ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev); > > > > > > This still requires a small, separate driver to setup the regmap and > > > do of_platform_populate(). The only difference is it lives in > > > drivers/usb/ instead of drivers/mfd/. > > > > > >> Or use the "simple-mfd", which is currently in -next: > > >> > > >> git show next/master:Documentation/devicetree/bindings/mfd/mfd.txt > > > > > > I'm not too opposed to this, but Thierry was when I brought this up > > > before. The issue here is that if we ever have to do something > > > besides setting up a regmap in the MFD, we'd have to change the > > > binding and break DT backwards-compatibility. > > > > Any thoughts on this? A minimal MFD seems to be the best way to > > future-proof this binding/driver should it need to be extended in the > > future. If this is a firm NAK from you however, I'll need to let > > Jassi now so that he can un-queue the mailbox patches for 4.2.... > > I was waiting to hear Thierry's thoughts. However, I am unconvinced > that you need an MFD driver for this and refuse to take a shell (read > "pointless") one on an "if we ever ..." clause. > > Will you break backwards capability though? I'm not sure you will. > Old DTBs will still use 'simple-mfd' and probe the devices in the > normal way. *If* you introduce an MFD driver at a later date then the > old DTB will miss out the *new* functionality, which is expected and > accepted. I'm a little confused by the simple-mfd approach. The only code I see in linux-next for this is a single line that adds the "simple-mfd" string to the OF device ID table in drivers/of/platform.c. As far as I can tell this will merely cause child devices to be created. There won't be a shared regmap and resources won't be set up properly either. Having a proper MFD driver seems to be the only way to achieve what we need. The reason why every other simple-mfd users seems to get away with this is because they also match on syscon and that sets up a regmap of its own and the child device drivers use the syscon API to get at it. So I don't see how we can make use of simple-mfd to achieve what we need, unless we essentially copy what syscon does (but do proper resource management while at it). There is also the matter of clocks, resets, power supplies, etc. which simple-mfd can't take into account in its current form. From a hardware point of view, (some of) the clocks and resets are shared by the XHCI and the mailbox blocks, so the device tree node would have to take that into account. And a driver would also have to know which clocks, resets and power supplies to probe and the order in which they need to be enabled. simple-mfd doesn't provide any of that currently, so we'd likely need to hack around that in all sorts of weird ways in the child drivers. It makes much more sense for a top-level MFD driver to set up the shared hardware resources and then instantiate the child devices and let the drivers for those only care about the child-specific resources. A catch-all driver will inevitably lead to implementing a midlayer with potentially all sorts of quirks to make it work with the various devices out there. A much better implementation, in my opinion, would be to make simple-mfd a subclassable object and then have drivers use a helper library to call code that is common for simple-mfd kinds of devices. Something like this for example: struct tegra_xusb { ... struct mfd_simple mfd; ... }; static int tegra_xusb_probe(struct platform_device *pdev) { struct tegra_xusb *xusb; ... err = mfd_simple_register(&xusb->mfd); ... } Now all these drivers reuse all the code provided by the mfd_simple helper, which will instantiate the children, but it is also very easy to tie in the platform-specific glue (clocks, resets, regulators, ...) via the device-specific drivers. Thierry
On Wed, May 20, 2015 at 4:52 PM, Thierry Reding <thierry.reding@gmail.com> wrote: > I'm a little confused by the simple-mfd approach. The only code I see in > linux-next for this is a single line that adds the "simple-mfd" string > to the OF device ID table in drivers/of/platform.c. As far as I can tell > this will merely cause child devices to be created. There won't be a > shared regmap and resources won't be set up properly either. That is correct. The simple-mfd is a two-component approach. Ideally, in the simplest case, you combine simple-mfd with syscon. foo@0 { compatible = "foo", "syscon", "simple-mfd"; reg = <0x10000000 0x1000>; bar@1 { compatible = "bar"; }; baz@2 { compatible = "baz"; }; }; This will instantiate bar and baz. These subdrivers then probe and: probe() { struct regmap *map; map = syscon_node_to_regmap(parent->of_node); (...) } Simple, syscon is the MFD hub. Yours, Linus Walleij -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Wed, 20 May 2015, Thierry Reding wrote: > On Wed, May 20, 2015 at 07:35:51AM +0100, Lee Jones wrote: > > On Tue, 19 May 2015, Andrew Bresticker wrote: > > > On Thu, May 14, 2015 at 10:38 AM, Andrew Bresticker > > > <abrestic@chromium.org> wrote: > > > > On Thu, May 14, 2015 at 12:40 AM, Lee Jones <lee.jones@linaro.org> wrote: > > > >> On Thu, 14 May 2015, Jon Hunter wrote: > > > >>> On 13/05/15 15:39, Lee Jones wrote: > > > >>> > On Mon, 04 May 2015, Andrew Bresticker wrote: > > > >>> > > > > >>> >> Add a binding document for the XUSB host complex on NVIDIA Tegra124 > > > >>> >> and later SoCs. The XUSB host complex includes a mailbox for > > > >>> >> communication with the XUSB micro-controller and an xHCI host-controller. > > > >>> >> > > > >>> >> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> > > > >>> >> Cc: Rob Herring <robh+dt@kernel.org> > > > >>> >> Cc: Pawel Moll <pawel.moll@arm.com> > > > >>> >> Cc: Mark Rutland <mark.rutland@arm.com> > > > >>> >> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> > > > >>> >> Cc: Kumar Gala <galak@codeaurora.org> > > > >>> >> Cc: Samuel Ortiz <sameo@linux.intel.com> > > > >>> >> Cc: Lee Jones <lee.jones@linaro.org> > > > >>> >> --- > > > >>> >> Changes from v7: > > > >>> >> - Move non-shared resources into child nodes. > > > >>> >> New for v7. > > > >>> >> --- > > > >>> >> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ > > > >>> >> 1 file changed, 37 insertions(+) > > > >>> >> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > > > >>> >> > > > >>> >> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > > > >>> >> new file mode 100644 > > > >>> >> index 0000000..bc50110 > > > >>> >> --- /dev/null > > > >>> >> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > > > >>> >> @@ -0,0 +1,37 @@ > > > >>> >> +NVIDIA Tegra XUSB host copmlex > > > >>> >> +============================== > > > >>> >> + > > > >>> >> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host > > > >>> >> +controller and a mailbox for communication with the XUSB micro-controller. > > > >>> >> + > > > >>> >> +Required properties: > > > >>> >> +-------------------- > > > >>> >> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". > > > >>> >> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' > > > >>> >> + where <chip> is tegra132. > > > >>> >> + - reg: Must contain the base and length of the XUSB FPCI registers. > > > >>> >> + - ranges: Bus address mapping for the XUSB block. Can be empty since the > > > >>> >> + mapping is 1:1. > > > >>> >> + - #address-cells: Must be 2. > > > >>> >> + - #size-cells: Must be 2. > > > >>> >> + > > > >>> >> +Example: > > > >>> >> +-------- > > > >>> >> + usb@0,70098000 { > > > >>> >> + compatible = "nvidia,tegra124-xusb"; > > > >>> >> + reg = <0x0 0x70098000 0x0 0x1000>; > > > >>> >> + ranges; > > > >>> >> + > > > >>> >> + #address-cells = <2>; > > > >>> >> + #size-cells = <2>; > > > >>> >> + > > > >>> >> + usb-host@0,70090000 { > > > >>> >> + compatible = "nvidia,tegra124-xhci"; > > > >>> >> + ... > > > >>> >> + }; > > > >>> >> + > > > >>> >> + mailbox { > > > >>> >> + compatible = "nvidia,tegra124-xusb-mbox"; > > > >>> >> + ... > > > >>> >> + }; > > > >>> > > > > >>> > This doesn't appear to be a proper MFD. I would have the USB and > > > >>> > Mailbox devices probe seperately and use a phandle to point the USB > > > >>> > device to its Mailbox. > > > >>> > > > > >>> > usb@xyz { > > > >>> > mboxes = <&xusb-mailbox, [chan]>; > > > >>> > }; > > > >>> > > > > >>> > > > >>> I am assuming that Andrew had laid it out like this to reflect the hw > > > >>> structure. The mailbox and xhci controller are part of the xusb > > > >>> sub-system and hence appear as child nodes. My understanding is that for > > > >>> device-tree we want the device-tree structure to reflect the actual hw. > > > >>> Is this not the case? > > > >> > > > >> Yes, the DT files should reflect h/w. I have requested to see what > > > >> the memory map looks like, so I might provide a more appropriate > > > >> solution to accepting a pretty pointless MFD. > > > > > > > > FWIW, the address map for XUSB looks like this: > > > > > > > > XUSB_HOST: 0x70090000 - 0x7009a000 > > > > xHCI registers: 0x70090000 - 0x70098000 > > > > FPCI configuration registers: 0x70098000 - 0x70099000 > > > > IPFS configuration registers: 0x70099000 - 0x7009a000 > > > > > > > >> Two solutions spring to mind. You can either call > > > >> of_platform_populate() from the USB driver, as some already do: > > > >> > > > >> drivers/usb/dwc3/dwc3-exynos.c: > > > >> ret = of_platform_populate(node, NULL, NULL, dev); > > > >> drivers/usb/dwc3/dwc3-keystone.c: > > > >> error = of_platform_populate(node, NULL, NULL, dev); > > > >> drivers/usb/dwc3/dwc3-omap.c: > > > >> ret = of_platform_populate(node, NULL, NULL, dev); > > > >> drivers/usb/dwc3/dwc3-qcom.c: > > > >> ret = of_platform_populate(node, NULL, NULL, qdwc->dev); > > > >> drivers/usb/dwc3/dwc3-st.c: > > > >> ret = of_platform_populate(node, NULL, NULL, dev); > > > >> drivers/usb/musb/musb_am335x.c: > > > >> ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev); > > > > > > > > This still requires a small, separate driver to setup the regmap and > > > > do of_platform_populate(). The only difference is it lives in > > > > drivers/usb/ instead of drivers/mfd/. > > > > > > > >> Or use the "simple-mfd", which is currently in -next: > > > >> > > > >> git show next/master:Documentation/devicetree/bindings/mfd/mfd.txt > > > > > > > > I'm not too opposed to this, but Thierry was when I brought this up > > > > before. The issue here is that if we ever have to do something > > > > besides setting up a regmap in the MFD, we'd have to change the > > > > binding and break DT backwards-compatibility. > > > > > > Any thoughts on this? A minimal MFD seems to be the best way to > > > future-proof this binding/driver should it need to be extended in the > > > future. If this is a firm NAK from you however, I'll need to let > > > Jassi now so that he can un-queue the mailbox patches for 4.2.... > > > > I was waiting to hear Thierry's thoughts. However, I am unconvinced > > that you need an MFD driver for this and refuse to take a shell (read > > "pointless") one on an "if we ever ..." clause. > > > > Will you break backwards capability though? I'm not sure you will. > > Old DTBs will still use 'simple-mfd' and probe the devices in the > > normal way. *If* you introduce an MFD driver at a later date then the > > old DTB will miss out the *new* functionality, which is expected and > > accepted. > > I'm a little confused by the simple-mfd approach. The only code I see in > linux-next for this is a single line that adds the "simple-mfd" string > to the OF device ID table in drivers/of/platform.c. As far as I can tell > this will merely cause child devices to be created. There won't be a > shared regmap and resources won't be set up properly either. Having a > proper MFD driver seems to be the only way to achieve what we need. > > The reason why every other simple-mfd users seems to get away with this > is because they also match on syscon and that sets up a regmap of its > own and the child device drivers use the syscon API to get at it. So I > don't see how we can make use of simple-mfd to achieve what we need, > unless we essentially copy what syscon does (but do proper resource > management while at it). If you have shared resources and your device isn't classed as a syscon device then yes, simple-mfd probably isn't suitable for this use-case. You might need to go into more detail with regards to "proper resource management", as I'm not entirely sure I agree. Still, this doesn't change the fact that, from what I've seen, I still don't think you need a dedicated MFD driver. What do you think of: usb-host@0,70090000 { compatible = "nvidia,tegra124-xhci"; reg = <0x0 0x70090000 0x0 0x80CF>, <0x0 0x70098800 0x0 0x0800>, <0x0 0x70099000 0x0 0x1000>; /* Something from the datasheet */ reg-names = "xhci-before-mbox", "xhci-after-mbox", "ipfs"; interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; ranges; xusb_mbox: mailbox { compatible = "nvidia,tegra124-xusb-mbox"; reg = <0x0 0x700980e0 0x0 0x13>, <0x0 0x70098428 0x0 0x03>; /* Something from the datasheet */ reg-names = "mbox-one", "mbox-two"; interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; }; }; Then hvae the XHCI driver call of_platform_populate() as I proposed above? > There is also the matter of clocks, resets, power supplies, etc. which > simple-mfd can't take into account in its current form. From a hardware > point of view, (some of) the clocks and resets are shared by the XHCI > and the mailbox blocks, so the device tree node would have to take that > into account. And a driver would also have to know which clocks, resets > and power supplies to probe and the order in which they need to be > enabled. simple-mfd doesn't provide any of that currently, so we'd > likely need to hack around that in all sorts of weird ways in the child > drivers. It makes much more sense for a top-level MFD driver to set up > the shared hardware resources and then instantiate the child devices and > let the drivers for those only care about the child-specific resources. > > A catch-all driver will inevitably lead to implementing a midlayer with > potentially all sorts of quirks to make it work with the various devices > out there. > > A much better implementation, in my opinion, would be to make simple-mfd > a subclassable object and then have drivers use a helper library to call > code that is common for simple-mfd kinds of devices. Something like this > for example: > > struct tegra_xusb { > ... > struct mfd_simple mfd; > ... > }; > > static int tegra_xusb_probe(struct platform_device *pdev) > { > struct tegra_xusb *xusb; > ... > err = mfd_simple_register(&xusb->mfd); > ... > } > > Now all these drivers reuse all the code provided by the mfd_simple > helper, which will instantiate the children, but it is also very easy to > tie in the platform-specific glue (clocks, resets, regulators, ...) via > the device-specific drivers. I'm not keen on creating a not-so-simple-mfd driver. Let's work with what we've got for the time being.
On Thu, May 21, 2015 at 09:40:01AM +0100, Lee Jones wrote: > On Wed, 20 May 2015, Thierry Reding wrote: > > On Wed, May 20, 2015 at 07:35:51AM +0100, Lee Jones wrote: > > > On Tue, 19 May 2015, Andrew Bresticker wrote: > > > > On Thu, May 14, 2015 at 10:38 AM, Andrew Bresticker > > > > <abrestic@chromium.org> wrote: > > > > > On Thu, May 14, 2015 at 12:40 AM, Lee Jones <lee.jones@linaro.org> wrote: > > > > >> On Thu, 14 May 2015, Jon Hunter wrote: > > > > >>> On 13/05/15 15:39, Lee Jones wrote: > > > > >>> > On Mon, 04 May 2015, Andrew Bresticker wrote: > > > > >>> > > > > > >>> >> Add a binding document for the XUSB host complex on NVIDIA Tegra124 > > > > >>> >> and later SoCs. The XUSB host complex includes a mailbox for > > > > >>> >> communication with the XUSB micro-controller and an xHCI host-controller. > > > > >>> >> > > > > >>> >> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> > > > > >>> >> Cc: Rob Herring <robh+dt@kernel.org> > > > > >>> >> Cc: Pawel Moll <pawel.moll@arm.com> > > > > >>> >> Cc: Mark Rutland <mark.rutland@arm.com> > > > > >>> >> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> > > > > >>> >> Cc: Kumar Gala <galak@codeaurora.org> > > > > >>> >> Cc: Samuel Ortiz <sameo@linux.intel.com> > > > > >>> >> Cc: Lee Jones <lee.jones@linaro.org> > > > > >>> >> --- > > > > >>> >> Changes from v7: > > > > >>> >> - Move non-shared resources into child nodes. > > > > >>> >> New for v7. > > > > >>> >> --- > > > > >>> >> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ > > > > >>> >> 1 file changed, 37 insertions(+) > > > > >>> >> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > > > > >>> >> > > > > >>> >> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > > > > >>> >> new file mode 100644 > > > > >>> >> index 0000000..bc50110 > > > > >>> >> --- /dev/null > > > > >>> >> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > > > > >>> >> @@ -0,0 +1,37 @@ > > > > >>> >> +NVIDIA Tegra XUSB host copmlex > > > > >>> >> +============================== > > > > >>> >> + > > > > >>> >> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host > > > > >>> >> +controller and a mailbox for communication with the XUSB micro-controller. > > > > >>> >> + > > > > >>> >> +Required properties: > > > > >>> >> +-------------------- > > > > >>> >> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". > > > > >>> >> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' > > > > >>> >> + where <chip> is tegra132. > > > > >>> >> + - reg: Must contain the base and length of the XUSB FPCI registers. > > > > >>> >> + - ranges: Bus address mapping for the XUSB block. Can be empty since the > > > > >>> >> + mapping is 1:1. > > > > >>> >> + - #address-cells: Must be 2. > > > > >>> >> + - #size-cells: Must be 2. > > > > >>> >> + > > > > >>> >> +Example: > > > > >>> >> +-------- > > > > >>> >> + usb@0,70098000 { > > > > >>> >> + compatible = "nvidia,tegra124-xusb"; > > > > >>> >> + reg = <0x0 0x70098000 0x0 0x1000>; > > > > >>> >> + ranges; > > > > >>> >> + > > > > >>> >> + #address-cells = <2>; > > > > >>> >> + #size-cells = <2>; > > > > >>> >> + > > > > >>> >> + usb-host@0,70090000 { > > > > >>> >> + compatible = "nvidia,tegra124-xhci"; > > > > >>> >> + ... > > > > >>> >> + }; > > > > >>> >> + > > > > >>> >> + mailbox { > > > > >>> >> + compatible = "nvidia,tegra124-xusb-mbox"; > > > > >>> >> + ... > > > > >>> >> + }; > > > > >>> > > > > > >>> > This doesn't appear to be a proper MFD. I would have the USB and > > > > >>> > Mailbox devices probe seperately and use a phandle to point the USB > > > > >>> > device to its Mailbox. > > > > >>> > > > > > >>> > usb@xyz { > > > > >>> > mboxes = <&xusb-mailbox, [chan]>; > > > > >>> > }; > > > > >>> > > > > > >>> > > > > >>> I am assuming that Andrew had laid it out like this to reflect the hw > > > > >>> structure. The mailbox and xhci controller are part of the xusb > > > > >>> sub-system and hence appear as child nodes. My understanding is that for > > > > >>> device-tree we want the device-tree structure to reflect the actual hw. > > > > >>> Is this not the case? > > > > >> > > > > >> Yes, the DT files should reflect h/w. I have requested to see what > > > > >> the memory map looks like, so I might provide a more appropriate > > > > >> solution to accepting a pretty pointless MFD. > > > > > > > > > > FWIW, the address map for XUSB looks like this: > > > > > > > > > > XUSB_HOST: 0x70090000 - 0x7009a000 > > > > > xHCI registers: 0x70090000 - 0x70098000 > > > > > FPCI configuration registers: 0x70098000 - 0x70099000 > > > > > IPFS configuration registers: 0x70099000 - 0x7009a000 > > > > > > > > > >> Two solutions spring to mind. You can either call > > > > >> of_platform_populate() from the USB driver, as some already do: > > > > >> > > > > >> drivers/usb/dwc3/dwc3-exynos.c: > > > > >> ret = of_platform_populate(node, NULL, NULL, dev); > > > > >> drivers/usb/dwc3/dwc3-keystone.c: > > > > >> error = of_platform_populate(node, NULL, NULL, dev); > > > > >> drivers/usb/dwc3/dwc3-omap.c: > > > > >> ret = of_platform_populate(node, NULL, NULL, dev); > > > > >> drivers/usb/dwc3/dwc3-qcom.c: > > > > >> ret = of_platform_populate(node, NULL, NULL, qdwc->dev); > > > > >> drivers/usb/dwc3/dwc3-st.c: > > > > >> ret = of_platform_populate(node, NULL, NULL, dev); > > > > >> drivers/usb/musb/musb_am335x.c: > > > > >> ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev); > > > > > > > > > > This still requires a small, separate driver to setup the regmap and > > > > > do of_platform_populate(). The only difference is it lives in > > > > > drivers/usb/ instead of drivers/mfd/. > > > > > > > > > >> Or use the "simple-mfd", which is currently in -next: > > > > >> > > > > >> git show next/master:Documentation/devicetree/bindings/mfd/mfd.txt > > > > > > > > > > I'm not too opposed to this, but Thierry was when I brought this up > > > > > before. The issue here is that if we ever have to do something > > > > > besides setting up a regmap in the MFD, we'd have to change the > > > > > binding and break DT backwards-compatibility. > > > > > > > > Any thoughts on this? A minimal MFD seems to be the best way to > > > > future-proof this binding/driver should it need to be extended in the > > > > future. If this is a firm NAK from you however, I'll need to let > > > > Jassi now so that he can un-queue the mailbox patches for 4.2.... > > > > > > I was waiting to hear Thierry's thoughts. However, I am unconvinced > > > that you need an MFD driver for this and refuse to take a shell (read > > > "pointless") one on an "if we ever ..." clause. > > > > > > Will you break backwards capability though? I'm not sure you will. > > > Old DTBs will still use 'simple-mfd' and probe the devices in the > > > normal way. *If* you introduce an MFD driver at a later date then the > > > old DTB will miss out the *new* functionality, which is expected and > > > accepted. > > > > I'm a little confused by the simple-mfd approach. The only code I see in > > linux-next for this is a single line that adds the "simple-mfd" string > > to the OF device ID table in drivers/of/platform.c. As far as I can tell > > this will merely cause child devices to be created. There won't be a > > shared regmap and resources won't be set up properly either. Having a > > proper MFD driver seems to be the only way to achieve what we need. > > > > The reason why every other simple-mfd users seems to get away with this > > is because they also match on syscon and that sets up a regmap of its > > own and the child device drivers use the syscon API to get at it. So I > > don't see how we can make use of simple-mfd to achieve what we need, > > unless we essentially copy what syscon does (but do proper resource > > management while at it). > > If you have shared resources and your device isn't classed as a syscon > device then yes, simple-mfd probably isn't suitable for this use-case. > You might need to go into more detail with regards to "proper resource > management", as I'm not entirely sure I agree. > > Still, this doesn't change the fact that, from what I've seen, I still > don't think you need a dedicated MFD driver. > > What do you think of: > > usb-host@0,70090000 { > compatible = "nvidia,tegra124-xhci"; > reg = <0x0 0x70090000 0x0 0x80CF>, > <0x0 0x70098800 0x0 0x0800>, > <0x0 0x70099000 0x0 0x1000>; > > /* Something from the datasheet */ > reg-names = "xhci-before-mbox", "xhci-after-mbox", "ipfs"; > > interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; > ranges; > > xusb_mbox: mailbox { > compatible = "nvidia,tegra124-xusb-mbox"; > reg = <0x0 0x700980e0 0x0 0x13>, > <0x0 0x70098428 0x0 0x03>; > > /* Something from the datasheet */ > reg-names = "mbox-one", "mbox-two"; > interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; > }; > }; > > Then hvae the XHCI driver call of_platform_populate() as I proposed > above? That's a little bonghits. It requires the drivers to jump through hoops to properly manage register accesses (needs to differentiate on the base depending on the register offset). So if you're going to NAK the MFD approach I'd rather go a completely different route and keep only a top- level node in DT here. One of the problems that the MFD design tries to solve is that the XHCI controller needs a reference to the mailbox and the pad controller for a PHY. The pad controller at the same time requires a reference to the mailbox, so we have a circular dependency that we can only resolve by introducing two separate devices, instantiated by some top-level entity. For that reason I don't think your proposal is going to work either. The circular dependency can't be broken because the XHCI driver will not be able to of_platform_populate() before getting a PHY, and the PHY will never show up until of_platform_populate() is called. So if this isn't going to be an MFD, then I think we should simply go and instantiate platform devices from the XUSB driver directly. The problem arising from that is that we have no place to put the top-level driver. We could take it into drivers/soc/tegra, or perhaps even have it in the XHCI driver. If we instantiate platform devices we can either set up the resources such that we don't have to jump through hoops (I think the resource tree will allow that) or set up a shared regmap. The latter might be the easier way out, though it'd also be copying much of what MFD does, but so be it if that's the only way we can get the matter settled. > > There is also the matter of clocks, resets, power supplies, etc. which > > simple-mfd can't take into account in its current form. From a hardware > > point of view, (some of) the clocks and resets are shared by the XHCI > > and the mailbox blocks, so the device tree node would have to take that > > into account. And a driver would also have to know which clocks, resets > > and power supplies to probe and the order in which they need to be > > enabled. simple-mfd doesn't provide any of that currently, so we'd > > likely need to hack around that in all sorts of weird ways in the child > > drivers. It makes much more sense for a top-level MFD driver to set up > > the shared hardware resources and then instantiate the child devices and > > let the drivers for those only care about the child-specific resources. > > > > A catch-all driver will inevitably lead to implementing a midlayer with > > potentially all sorts of quirks to make it work with the various devices > > out there. > > > > A much better implementation, in my opinion, would be to make simple-mfd > > a subclassable object and then have drivers use a helper library to call > > code that is common for simple-mfd kinds of devices. Something like this > > for example: > > > > struct tegra_xusb { > > ... > > struct mfd_simple mfd; > > ... > > }; > > > > static int tegra_xusb_probe(struct platform_device *pdev) > > { > > struct tegra_xusb *xusb; > > ... > > err = mfd_simple_register(&xusb->mfd); > > ... > > } > > > > Now all these drivers reuse all the code provided by the mfd_simple > > helper, which will instantiate the children, but it is also very easy to > > tie in the platform-specific glue (clocks, resets, regulators, ...) via > > the device-specific drivers. > > I'm not keen on creating a not-so-simple-mfd driver. Let's work with > what we've got for the time being. What we currently have is not a driver at all, it's merely an alias for simple-bus. Thierry
On Thu, 21 May 2015, Thierry Reding wrote: > On Thu, May 21, 2015 at 09:40:01AM +0100, Lee Jones wrote: > > On Wed, 20 May 2015, Thierry Reding wrote: > > > On Wed, May 20, 2015 at 07:35:51AM +0100, Lee Jones wrote: > > > > On Tue, 19 May 2015, Andrew Bresticker wrote: > > > > > On Thu, May 14, 2015 at 10:38 AM, Andrew Bresticker > > > > > <abrestic@chromium.org> wrote: > > > > > > On Thu, May 14, 2015 at 12:40 AM, Lee Jones <lee.jones@linaro.org> wrote: > > > > > >> On Thu, 14 May 2015, Jon Hunter wrote: > > > > > >>> On 13/05/15 15:39, Lee Jones wrote: > > > > > >>> > On Mon, 04 May 2015, Andrew Bresticker wrote: > > > > > >>> > > > > > > >>> >> Add a binding document for the XUSB host complex on NVIDIA Tegra124 > > > > > >>> >> and later SoCs. The XUSB host complex includes a mailbox for > > > > > >>> >> communication with the XUSB micro-controller and an xHCI host-controller. > > > > > >>> >> > > > > > >>> >> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> > > > > > >>> >> Cc: Rob Herring <robh+dt@kernel.org> > > > > > >>> >> Cc: Pawel Moll <pawel.moll@arm.com> > > > > > >>> >> Cc: Mark Rutland <mark.rutland@arm.com> > > > > > >>> >> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> > > > > > >>> >> Cc: Kumar Gala <galak@codeaurora.org> > > > > > >>> >> Cc: Samuel Ortiz <sameo@linux.intel.com> > > > > > >>> >> Cc: Lee Jones <lee.jones@linaro.org> > > > > > >>> >> --- > > > > > >>> >> Changes from v7: > > > > > >>> >> - Move non-shared resources into child nodes. > > > > > >>> >> New for v7. > > > > > >>> >> --- > > > > > >>> >> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ > > > > > >>> >> 1 file changed, 37 insertions(+) > > > > > >>> >> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > > > > > >>> >> > > > > > >>> >> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > > > > > >>> >> new file mode 100644 > > > > > >>> >> index 0000000..bc50110 > > > > > >>> >> --- /dev/null > > > > > >>> >> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > > > > > >>> >> @@ -0,0 +1,37 @@ > > > > > >>> >> +NVIDIA Tegra XUSB host copmlex > > > > > >>> >> +============================== > > > > > >>> >> + > > > > > >>> >> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host > > > > > >>> >> +controller and a mailbox for communication with the XUSB micro-controller. > > > > > >>> >> + > > > > > >>> >> +Required properties: > > > > > >>> >> +-------------------- > > > > > >>> >> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". > > > > > >>> >> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' > > > > > >>> >> + where <chip> is tegra132. > > > > > >>> >> + - reg: Must contain the base and length of the XUSB FPCI registers. > > > > > >>> >> + - ranges: Bus address mapping for the XUSB block. Can be empty since the > > > > > >>> >> + mapping is 1:1. > > > > > >>> >> + - #address-cells: Must be 2. > > > > > >>> >> + - #size-cells: Must be 2. > > > > > >>> >> + > > > > > >>> >> +Example: > > > > > >>> >> +-------- > > > > > >>> >> + usb@0,70098000 { > > > > > >>> >> + compatible = "nvidia,tegra124-xusb"; > > > > > >>> >> + reg = <0x0 0x70098000 0x0 0x1000>; > > > > > >>> >> + ranges; > > > > > >>> >> + > > > > > >>> >> + #address-cells = <2>; > > > > > >>> >> + #size-cells = <2>; > > > > > >>> >> + > > > > > >>> >> + usb-host@0,70090000 { > > > > > >>> >> + compatible = "nvidia,tegra124-xhci"; > > > > > >>> >> + ... > > > > > >>> >> + }; > > > > > >>> >> + > > > > > >>> >> + mailbox { > > > > > >>> >> + compatible = "nvidia,tegra124-xusb-mbox"; > > > > > >>> >> + ... > > > > > >>> >> + }; > > > > > >>> > > > > > > >>> > This doesn't appear to be a proper MFD. I would have the USB and > > > > > >>> > Mailbox devices probe seperately and use a phandle to point the USB > > > > > >>> > device to its Mailbox. > > > > > >>> > > > > > > >>> > usb@xyz { > > > > > >>> > mboxes = <&xusb-mailbox, [chan]>; > > > > > >>> > }; > > > > > >>> > > > > > > >>> > > > > > >>> I am assuming that Andrew had laid it out like this to reflect the hw > > > > > >>> structure. The mailbox and xhci controller are part of the xusb > > > > > >>> sub-system and hence appear as child nodes. My understanding is that for > > > > > >>> device-tree we want the device-tree structure to reflect the actual hw. > > > > > >>> Is this not the case? > > > > > >> > > > > > >> Yes, the DT files should reflect h/w. I have requested to see what > > > > > >> the memory map looks like, so I might provide a more appropriate > > > > > >> solution to accepting a pretty pointless MFD. > > > > > > > > > > > > FWIW, the address map for XUSB looks like this: > > > > > > > > > > > > XUSB_HOST: 0x70090000 - 0x7009a000 > > > > > > xHCI registers: 0x70090000 - 0x70098000 > > > > > > FPCI configuration registers: 0x70098000 - 0x70099000 > > > > > > IPFS configuration registers: 0x70099000 - 0x7009a000 > > > > > > > > > > > >> Two solutions spring to mind. You can either call > > > > > >> of_platform_populate() from the USB driver, as some already do: > > > > > >> > > > > > >> drivers/usb/dwc3/dwc3-exynos.c: > > > > > >> ret = of_platform_populate(node, NULL, NULL, dev); > > > > > >> drivers/usb/dwc3/dwc3-keystone.c: > > > > > >> error = of_platform_populate(node, NULL, NULL, dev); > > > > > >> drivers/usb/dwc3/dwc3-omap.c: > > > > > >> ret = of_platform_populate(node, NULL, NULL, dev); > > > > > >> drivers/usb/dwc3/dwc3-qcom.c: > > > > > >> ret = of_platform_populate(node, NULL, NULL, qdwc->dev); > > > > > >> drivers/usb/dwc3/dwc3-st.c: > > > > > >> ret = of_platform_populate(node, NULL, NULL, dev); > > > > > >> drivers/usb/musb/musb_am335x.c: > > > > > >> ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev); > > > > > > > > > > > > This still requires a small, separate driver to setup the regmap and > > > > > > do of_platform_populate(). The only difference is it lives in > > > > > > drivers/usb/ instead of drivers/mfd/. > > > > > > > > > > > >> Or use the "simple-mfd", which is currently in -next: > > > > > >> > > > > > >> git show next/master:Documentation/devicetree/bindings/mfd/mfd.txt > > > > > > > > > > > > I'm not too opposed to this, but Thierry was when I brought this up > > > > > > before. The issue here is that if we ever have to do something > > > > > > besides setting up a regmap in the MFD, we'd have to change the > > > > > > binding and break DT backwards-compatibility. > > > > > > > > > > Any thoughts on this? A minimal MFD seems to be the best way to > > > > > future-proof this binding/driver should it need to be extended in the > > > > > future. If this is a firm NAK from you however, I'll need to let > > > > > Jassi now so that he can un-queue the mailbox patches for 4.2.... > > > > > > > > I was waiting to hear Thierry's thoughts. However, I am unconvinced > > > > that you need an MFD driver for this and refuse to take a shell (read > > > > "pointless") one on an "if we ever ..." clause. > > > > > > > > Will you break backwards capability though? I'm not sure you will. > > > > Old DTBs will still use 'simple-mfd' and probe the devices in the > > > > normal way. *If* you introduce an MFD driver at a later date then the > > > > old DTB will miss out the *new* functionality, which is expected and > > > > accepted. > > > > > > I'm a little confused by the simple-mfd approach. The only code I see in > > > linux-next for this is a single line that adds the "simple-mfd" string > > > to the OF device ID table in drivers/of/platform.c. As far as I can tell > > > this will merely cause child devices to be created. There won't be a > > > shared regmap and resources won't be set up properly either. Having a > > > proper MFD driver seems to be the only way to achieve what we need. > > > > > > The reason why every other simple-mfd users seems to get away with this > > > is because they also match on syscon and that sets up a regmap of its > > > own and the child device drivers use the syscon API to get at it. So I > > > don't see how we can make use of simple-mfd to achieve what we need, > > > unless we essentially copy what syscon does (but do proper resource > > > management while at it). > > > > If you have shared resources and your device isn't classed as a syscon > > device then yes, simple-mfd probably isn't suitable for this use-case. > > You might need to go into more detail with regards to "proper resource > > management", as I'm not entirely sure I agree. > > > > Still, this doesn't change the fact that, from what I've seen, I still > > don't think you need a dedicated MFD driver. > > > > What do you think of: > > > > usb-host@0,70090000 { > > compatible = "nvidia,tegra124-xhci"; > > reg = <0x0 0x70090000 0x0 0x80CF>, > > <0x0 0x70098800 0x0 0x0800>, > > <0x0 0x70099000 0x0 0x1000>; > > > > /* Something from the datasheet */ > > reg-names = "xhci-before-mbox", "xhci-after-mbox", "ipfs"; > > > > interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; > > ranges; > > > > xusb_mbox: mailbox { > > compatible = "nvidia,tegra124-xusb-mbox"; > > reg = <0x0 0x700980e0 0x0 0x13>, > > <0x0 0x70098428 0x0 0x03>; > > > > /* Something from the datasheet */ > > reg-names = "mbox-one", "mbox-two"; > > interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; > > }; > > }; > > > > Then hvae the XHCI driver call of_platform_populate() as I proposed > > above? > > That's a little bonghits. It requires the drivers to jump through hoops > to properly manage register accesses (needs to differentiate on the base > depending on the register offset). So if you're going to NAK the MFD > approach I'd rather go a completely different route and keep only a top- > level node in DT here. > > One of the problems that the MFD design tries to solve is that the XHCI > controller needs a reference to the mailbox and the pad controller for a > PHY. The pad controller at the same time requires a reference to the > mailbox, so we have a circular dependency that we can only resolve by > introducing two separate devices, instantiated by some top-level entity. > For that reason I don't think your proposal is going to work either. The > circular dependency can't be broken because the XHCI driver will not be > able to of_platform_populate() before getting a PHY, and the PHY will > never show up until of_platform_populate() is called. > > So if this isn't going to be an MFD, then I think we should simply go > and instantiate platform devices from the XUSB driver directly. The > problem arising from that is that we have no place to put the top-level > driver. We could take it into drivers/soc/tegra, or perhaps even have it > in the XHCI driver. > > If we instantiate platform devices we can either set up the resources > such that we don't have to jump through hoops (I think the resource tree > will allow that) or set up a shared regmap. The latter might be the > easier way out, though it'd also be copying much of what MFD does, but > so be it if that's the only way we can get the matter settled. I understand the difficulties identified and empathise with your situation. I just can't bring myself to justify that a USB device which has it's own Mailbox is an MFD. If you take a look above, you can see some examples of other USB drivers registering sub-devices. I think you can make this work well for your setup. > > > There is also the matter of clocks, resets, power supplies, etc. which > > > simple-mfd can't take into account in its current form. From a hardware > > > point of view, (some of) the clocks and resets are shared by the XHCI > > > and the mailbox blocks, so the device tree node would have to take that > > > into account. And a driver would also have to know which clocks, resets > > > and power supplies to probe and the order in which they need to be > > > enabled. simple-mfd doesn't provide any of that currently, so we'd > > > likely need to hack around that in all sorts of weird ways in the child > > > drivers. It makes much more sense for a top-level MFD driver to set up > > > the shared hardware resources and then instantiate the child devices and > > > let the drivers for those only care about the child-specific resources. > > > > > > A catch-all driver will inevitably lead to implementing a midlayer with > > > potentially all sorts of quirks to make it work with the various devices > > > out there. > > > > > > A much better implementation, in my opinion, would be to make simple-mfd > > > a subclassable object and then have drivers use a helper library to call > > > code that is common for simple-mfd kinds of devices. Something like this > > > for example: > > > > > > struct tegra_xusb { > > > ... > > > struct mfd_simple mfd; > > > ... > > > }; > > > > > > static int tegra_xusb_probe(struct platform_device *pdev) > > > { > > > struct tegra_xusb *xusb; > > > ... > > > err = mfd_simple_register(&xusb->mfd); > > > ... > > > } > > > > > > Now all these drivers reuse all the code provided by the mfd_simple > > > helper, which will instantiate the children, but it is also very easy to > > > tie in the platform-specific glue (clocks, resets, regulators, ...) via > > > the device-specific drivers. > > > > I'm not keen on creating a not-so-simple-mfd driver. Let's work with > > what we've got for the time being. > > What we currently have is not a driver at all, it's merely an alias for > simple-bus. Right, which is exactly what it was designed to be. Initially we were using simple-bus, but some people (rightly) thought this an abuse 'cos MFD isn't really a bus.
On Tue, 26 May 2015 16:18:54 +0100 , Lee Jones <lee.jones@linaro.org> wrote: > On Thu, 21 May 2015, Thierry Reding wrote: > > > On Thu, May 21, 2015 at 09:40:01AM +0100, Lee Jones wrote: > > > On Wed, 20 May 2015, Thierry Reding wrote: > > > > On Wed, May 20, 2015 at 07:35:51AM +0100, Lee Jones wrote: > > > > > On Tue, 19 May 2015, Andrew Bresticker wrote: > > > > > > On Thu, May 14, 2015 at 10:38 AM, Andrew Bresticker > > > > > > <abrestic@chromium.org> wrote: > > > > > > > On Thu, May 14, 2015 at 12:40 AM, Lee Jones <lee.jones@linaro.org> wrote: > > > > > > >> On Thu, 14 May 2015, Jon Hunter wrote: > > > > > > >>> On 13/05/15 15:39, Lee Jones wrote: > > > > > > >>> > On Mon, 04 May 2015, Andrew Bresticker wrote: > > > > > > >>> > > > > > > > >>> >> Add a binding document for the XUSB host complex on NVIDIA Tegra124 > > > > > > >>> >> and later SoCs. The XUSB host complex includes a mailbox for > > > > > > >>> >> communication with the XUSB micro-controller and an xHCI host-controller. > > > > > > >>> >> > > > > > > >>> >> Signed-off-by: Andrew Bresticker <abrestic@chromium.org> > > > > > > >>> >> Cc: Rob Herring <robh+dt@kernel.org> > > > > > > >>> >> Cc: Pawel Moll <pawel.moll@arm.com> > > > > > > >>> >> Cc: Mark Rutland <mark.rutland@arm.com> > > > > > > >>> >> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> > > > > > > >>> >> Cc: Kumar Gala <galak@codeaurora.org> > > > > > > >>> >> Cc: Samuel Ortiz <sameo@linux.intel.com> > > > > > > >>> >> Cc: Lee Jones <lee.jones@linaro.org> > > > > > > >>> >> --- > > > > > > >>> >> Changes from v7: > > > > > > >>> >> - Move non-shared resources into child nodes. > > > > > > >>> >> New for v7. > > > > > > >>> >> --- > > > > > > >>> >> .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ > > > > > > >>> >> 1 file changed, 37 insertions(+) > > > > > > >>> >> create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > > > > > > >>> >> > > > > > > >>> >> diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > > > > > > >>> >> new file mode 100644 > > > > > > >>> >> index 0000000..bc50110 > > > > > > >>> >> --- /dev/null > > > > > > >>> >> +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt > > > > > > >>> >> @@ -0,0 +1,37 @@ > > > > > > >>> >> +NVIDIA Tegra XUSB host copmlex > > > > > > >>> >> +============================== > > > > > > >>> >> + > > > > > > >>> >> +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host > > > > > > >>> >> +controller and a mailbox for communication with the XUSB micro-controller. > > > > > > >>> >> + > > > > > > >>> >> +Required properties: > > > > > > >>> >> +-------------------- > > > > > > >>> >> + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". > > > > > > >>> >> + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' > > > > > > >>> >> + where <chip> is tegra132. > > > > > > >>> >> + - reg: Must contain the base and length of the XUSB FPCI registers. > > > > > > >>> >> + - ranges: Bus address mapping for the XUSB block. Can be empty since the > > > > > > >>> >> + mapping is 1:1. > > > > > > >>> >> + - #address-cells: Must be 2. > > > > > > >>> >> + - #size-cells: Must be 2. > > > > > > >>> >> + > > > > > > >>> >> +Example: > > > > > > >>> >> +-------- > > > > > > >>> >> + usb@0,70098000 { > > > > > > >>> >> + compatible = "nvidia,tegra124-xusb"; > > > > > > >>> >> + reg = <0x0 0x70098000 0x0 0x1000>; > > > > > > >>> >> + ranges; > > > > > > >>> >> + > > > > > > >>> >> + #address-cells = <2>; > > > > > > >>> >> + #size-cells = <2>; > > > > > > >>> >> + > > > > > > >>> >> + usb-host@0,70090000 { > > > > > > >>> >> + compatible = "nvidia,tegra124-xhci"; > > > > > > >>> >> + ... > > > > > > >>> >> + }; > > > > > > >>> >> + > > > > > > >>> >> + mailbox { > > > > > > >>> >> + compatible = "nvidia,tegra124-xusb-mbox"; > > > > > > >>> >> + ... > > > > > > >>> >> + }; > > > > > > >>> > > > > > > > >>> > This doesn't appear to be a proper MFD. I would have the USB and > > > > > > >>> > Mailbox devices probe seperately and use a phandle to point the USB > > > > > > >>> > device to its Mailbox. > > > > > > >>> > > > > > > > >>> > usb@xyz { > > > > > > >>> > mboxes = <&xusb-mailbox, [chan]>; > > > > > > >>> > }; > > > > > > >>> > > > > > > > >>> > > > > > > >>> I am assuming that Andrew had laid it out like this to reflect the hw > > > > > > >>> structure. The mailbox and xhci controller are part of the xusb > > > > > > >>> sub-system and hence appear as child nodes. My understanding is that for > > > > > > >>> device-tree we want the device-tree structure to reflect the actual hw. > > > > > > >>> Is this not the case? > > > > > > >> > > > > > > >> Yes, the DT files should reflect h/w. I have requested to see what > > > > > > >> the memory map looks like, so I might provide a more appropriate > > > > > > >> solution to accepting a pretty pointless MFD. > > > > > > > > > > > > > > FWIW, the address map for XUSB looks like this: > > > > > > > > > > > > > > XUSB_HOST: 0x70090000 - 0x7009a000 > > > > > > > xHCI registers: 0x70090000 - 0x70098000 > > > > > > > FPCI configuration registers: 0x70098000 - 0x70099000 > > > > > > > IPFS configuration registers: 0x70099000 - 0x7009a000 > > > > > > > > > > > > > >> Two solutions spring to mind. You can either call > > > > > > >> of_platform_populate() from the USB driver, as some already do: > > > > > > >> > > > > > > >> drivers/usb/dwc3/dwc3-exynos.c: > > > > > > >> ret = of_platform_populate(node, NULL, NULL, dev); > > > > > > >> drivers/usb/dwc3/dwc3-keystone.c: > > > > > > >> error = of_platform_populate(node, NULL, NULL, dev); > > > > > > >> drivers/usb/dwc3/dwc3-omap.c: > > > > > > >> ret = of_platform_populate(node, NULL, NULL, dev); > > > > > > >> drivers/usb/dwc3/dwc3-qcom.c: > > > > > > >> ret = of_platform_populate(node, NULL, NULL, qdwc->dev); > > > > > > >> drivers/usb/dwc3/dwc3-st.c: > > > > > > >> ret = of_platform_populate(node, NULL, NULL, dev); > > > > > > >> drivers/usb/musb/musb_am335x.c: > > > > > > >> ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev); > > > > > > > > > > > > > > This still requires a small, separate driver to setup the regmap and > > > > > > > do of_platform_populate(). The only difference is it lives in > > > > > > > drivers/usb/ instead of drivers/mfd/. > > > > > > > > > > > > > >> Or use the "simple-mfd", which is currently in -next: > > > > > > >> > > > > > > >> git show next/master:Documentation/devicetree/bindings/mfd/mfd.txt > > > > > > > > > > > > > > I'm not too opposed to this, but Thierry was when I brought this up > > > > > > > before. The issue here is that if we ever have to do something > > > > > > > besides setting up a regmap in the MFD, we'd have to change the > > > > > > > binding and break DT backwards-compatibility. > > > > > > > > > > > > Any thoughts on this? A minimal MFD seems to be the best way to > > > > > > future-proof this binding/driver should it need to be extended in the > > > > > > future. If this is a firm NAK from you however, I'll need to let > > > > > > Jassi now so that he can un-queue the mailbox patches for 4.2.... > > > > > > > > > > I was waiting to hear Thierry's thoughts. However, I am unconvinced > > > > > that you need an MFD driver for this and refuse to take a shell (read > > > > > "pointless") one on an "if we ever ..." clause. > > > > > > > > > > Will you break backwards capability though? I'm not sure you will. > > > > > Old DTBs will still use 'simple-mfd' and probe the devices in the > > > > > normal way. *If* you introduce an MFD driver at a later date then the > > > > > old DTB will miss out the *new* functionality, which is expected and > > > > > accepted. > > > > > > > > I'm a little confused by the simple-mfd approach. The only code I see in > > > > linux-next for this is a single line that adds the "simple-mfd" string > > > > to the OF device ID table in drivers/of/platform.c. As far as I can tell > > > > this will merely cause child devices to be created. There won't be a > > > > shared regmap and resources won't be set up properly either. Having a > > > > proper MFD driver seems to be the only way to achieve what we need. > > > > > > > > The reason why every other simple-mfd users seems to get away with this > > > > is because they also match on syscon and that sets up a regmap of its > > > > own and the child device drivers use the syscon API to get at it. So I > > > > don't see how we can make use of simple-mfd to achieve what we need, > > > > unless we essentially copy what syscon does (but do proper resource > > > > management while at it). > > > > > > If you have shared resources and your device isn't classed as a syscon > > > device then yes, simple-mfd probably isn't suitable for this use-case. > > > You might need to go into more detail with regards to "proper resource > > > management", as I'm not entirely sure I agree. > > > > > > Still, this doesn't change the fact that, from what I've seen, I still > > > don't think you need a dedicated MFD driver. > > > > > > What do you think of: > > > > > > usb-host@0,70090000 { > > > compatible = "nvidia,tegra124-xhci"; > > > reg = <0x0 0x70090000 0x0 0x80CF>, > > > <0x0 0x70098800 0x0 0x0800>, > > > <0x0 0x70099000 0x0 0x1000>; > > > > > > /* Something from the datasheet */ > > > reg-names = "xhci-before-mbox", "xhci-after-mbox", "ipfs"; > > > > > > interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; > > > ranges; > > > > > > xusb_mbox: mailbox { > > > compatible = "nvidia,tegra124-xusb-mbox"; > > > reg = <0x0 0x700980e0 0x0 0x13>, > > > <0x0 0x70098428 0x0 0x03>; > > > > > > /* Something from the datasheet */ > > > reg-names = "mbox-one", "mbox-two"; > > > interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; > > > }; > > > }; > > > > > > Then hvae the XHCI driver call of_platform_populate() as I proposed > > > above? > > > > That's a little bonghits. It requires the drivers to jump through hoops > > to properly manage register accesses (needs to differentiate on the base > > depending on the register offset). So if you're going to NAK the MFD > > approach I'd rather go a completely different route and keep only a top- > > level node in DT here. > > > > One of the problems that the MFD design tries to solve is that the XHCI > > controller needs a reference to the mailbox and the pad controller for a > > PHY. The pad controller at the same time requires a reference to the > > mailbox, so we have a circular dependency that we can only resolve by > > introducing two separate devices, instantiated by some top-level entity. > > For that reason I don't think your proposal is going to work either. The > > circular dependency can't be broken because the XHCI driver will not be > > able to of_platform_populate() before getting a PHY, and the PHY will > > never show up until of_platform_populate() is called. > > > > So if this isn't going to be an MFD, then I think we should simply go > > and instantiate platform devices from the XUSB driver directly. The > > problem arising from that is that we have no place to put the top-level > > driver. We could take it into drivers/soc/tegra, or perhaps even have it > > in the XHCI driver. > > > > If we instantiate platform devices we can either set up the resources > > such that we don't have to jump through hoops (I think the resource tree > > will allow that) or set up a shared regmap. The latter might be the > > easier way out, though it'd also be copying much of what MFD does, but > > so be it if that's the only way we can get the matter settled. > > I understand the difficulties identified and empathise with your > situation. I just can't bring myself to justify that a USB device > which has it's own Mailbox is an MFD. If you take a look above, you > can see some examples of other USB drivers registering sub-devices. I > think you can make this work well for your setup. Not using MFD I would say is completely justified. I think too many devices try to get shoehorned into MFD when there really isn't a need for it. g. -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt new file mode 100644 index 0000000..bc50110 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt @@ -0,0 +1,37 @@ +NVIDIA Tegra XUSB host copmlex +============================== + +The XUSB host complex on Tegra124 and later SoCs contains an xHCI host +controller and a mailbox for communication with the XUSB micro-controller. + +Required properties: +-------------------- + - compatible: For Tegra124, must contain "nvidia,tegra124-xusb". + Otherwise, must contain '"nvidia,<chip>-xusb", "nvidia,tegra124-xusb"' + where <chip> is tegra132. + - reg: Must contain the base and length of the XUSB FPCI registers. + - ranges: Bus address mapping for the XUSB block. Can be empty since the + mapping is 1:1. + - #address-cells: Must be 2. + - #size-cells: Must be 2. + +Example: +-------- + usb@0,70098000 { + compatible = "nvidia,tegra124-xusb"; + reg = <0x0 0x70098000 0x0 0x1000>; + ranges; + + #address-cells = <2>; + #size-cells = <2>; + + usb-host@0,70090000 { + compatible = "nvidia,tegra124-xhci"; + ... + }; + + mailbox { + compatible = "nvidia,tegra124-xusb-mbox"; + ... + }; + };
Add a binding document for the XUSB host complex on NVIDIA Tegra124 and later SoCs. The XUSB host complex includes a mailbox for communication with the XUSB micro-controller and an xHCI host-controller. Signed-off-by: Andrew Bresticker <abrestic@chromium.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Lee Jones <lee.jones@linaro.org> --- Changes from v7: - Move non-shared resources into child nodes. New for v7. --- .../bindings/mfd/nvidia,tegra124-xusb.txt | 37 ++++++++++++++++++++++ 1 file changed, 37 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/nvidia,tegra124-xusb.txt