Message ID | 1427202346-12502-4-git-send-email-vladz@cloudius-systems.com |
---|---|
State | Awaiting Upstream, archived |
Delegated to: | David Miller |
Headers | show |
>-----Original Message----- >From: netdev-owner@vger.kernel.org [mailto:netdev-owner@vger.kernel.org] On Behalf Of Vlad Zolotarov >Sent: Tuesday, March 24, 2015 6:06 AM >Subject: [PATCH net-next v7 3/7] ixgbe: Add a RETA query command to VF-PF channel API > >82599 and x540 VFs and PF share the same RSS redirection table (RETA). Therefore we >just return it for all VFs. x550 on the other hand provides a separate redirection >table for each VF (there is a per-pool RETA table). > >For 82599 and x540 RETA table is an array of 32 registers (128 bytes) and the maximum number of >registers that may be delivered in a single VF-PF channel command is 15. Therefore >we will deliver the whole table in 3 steps: 12, 12 and 8 registers in each >step correspondingly. > >For x550 VFs RETA is a 64 byte array, so we may deliver it in two steps: 12 and 4 registers >correspondingly. > >Thus this patch does the following: > > - Adds a new API version (to specify a new commands set). > - Adds the IXGBE_VF_GET_RETA command to the VF-PF commands set. > >Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com> >--- <snip> +static int ixgbe_get_vf_reta(struct ixgbe_adapter *adapter, u32 *msgbuf, u32 vf) +{ + struct ixgbe_hw *hw = &adapter->hw; + int i, j; + u32 *reta = &msgbuf[1]; + u32 mask = 0; + u32 psrtype; + u32 reta_offset_dw = msgbuf[IXGBE_VF_RETA_OFFSET]; + u32 dwords = msgbuf[IXGBE_VF_RETA_SZ]; + + /* verify the PF is supporting the correct API */ + if (!adapter->vfinfo[vf].rss_query_enabled || + (adapter->vfinfo[vf].vf_api != ixgbe_mbox_api_12)) + return -EPERM; + + psrtype = IXGBE_READ_REG(hw, IXGBE_PSRTYPE(vf)); + + /* The redirection table is composed as follows: + * 82598: 128 (8 bit wide) entries containing pair of 4 bit RSS indices + * 82599/X540: 128 (8 bit wide) entries containing 4 bit RSS index X550: + * 512 (8 bit wide) entries containing 6 bit RSS index + * + * PSRTYPE[n].RQPL defines if 0, 1 or 2 bits from the redirection table + * value should be used. + */ + + if ((psrtype & (1 << 29)) == (1 << 29)) + mask = 0x01010101; + else if ((psrtype & (2 << 29)) == (2 << 29)) + mask = 0x03030303; + else + mask = 0; + + switch (hw->mac.type) { + case ixgbe_mac_82599EB: + case ixgbe_mac_X540: + /* Read the appropriate portion of RETA */ + for (i = 0; i < dwords; i++) + reta[i] = IXGBE_READ_REG(hw, + IXGBE_RETA(i + reta_offset_dw)); + break; + case ixgbe_mac_X550: + case ixgbe_mac_X550EM_x: + /* X550 has a per-VF RETA */ + for (i = 0, j = reta_offset_dw; i < dwords; i++, j++) + reta[i] = IXGBE_READ_REG(hw, + IXGBE_PFVFRETA(j, vf)); + break; + default: + return -1; There is no need to query the X550 info through the mailbox - this information can be obtained directly from the VF registers. Thanks, Emil -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 03/25/15 20:03, Tantilov, Emil S wrote: >> -----Original Message----- >> From: netdev-owner@vger.kernel.org [mailto:netdev-owner@vger.kernel.org] On Behalf Of Vlad Zolotarov >> Sent: Tuesday, March 24, 2015 6:06 AM >> Subject: [PATCH net-next v7 3/7] ixgbe: Add a RETA query command to VF-PF channel API >> >> 82599 and x540 VFs and PF share the same RSS redirection table (RETA). Therefore we >> just return it for all VFs. x550 on the other hand provides a separate redirection >> table for each VF (there is a per-pool RETA table). >> >> For 82599 and x540 RETA table is an array of 32 registers (128 bytes) and the maximum number of >> registers that may be delivered in a single VF-PF channel command is 15. Therefore >> we will deliver the whole table in 3 steps: 12, 12 and 8 registers in each >> step correspondingly. >> >> For x550 VFs RETA is a 64 byte array, so we may deliver it in two steps: 12 and 4 registers >> correspondingly. >> >> Thus this patch does the following: >> >> - Adds a new API version (to specify a new commands set). >> - Adds the IXGBE_VF_GET_RETA command to the VF-PF commands set. >> >> Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com> >> --- > <snip> > > +static int ixgbe_get_vf_reta(struct ixgbe_adapter *adapter, u32 *msgbuf, u32 vf) > +{ > + struct ixgbe_hw *hw = &adapter->hw; > + int i, j; > + u32 *reta = &msgbuf[1]; > + u32 mask = 0; > + u32 psrtype; > + u32 reta_offset_dw = msgbuf[IXGBE_VF_RETA_OFFSET]; > + u32 dwords = msgbuf[IXGBE_VF_RETA_SZ]; > + > + /* verify the PF is supporting the correct API */ > + if (!adapter->vfinfo[vf].rss_query_enabled || > + (adapter->vfinfo[vf].vf_api != ixgbe_mbox_api_12)) > + return -EPERM; > + > + psrtype = IXGBE_READ_REG(hw, IXGBE_PSRTYPE(vf)); > + > + /* The redirection table is composed as follows: > + * 82598: 128 (8 bit wide) entries containing pair of 4 bit RSS indices > + * 82599/X540: 128 (8 bit wide) entries containing 4 bit RSS index X550: > + * 512 (8 bit wide) entries containing 6 bit RSS index > + * > + * PSRTYPE[n].RQPL defines if 0, 1 or 2 bits from the redirection table > + * value should be used. > + */ > + > + if ((psrtype & (1 << 29)) == (1 << 29)) > + mask = 0x01010101; > + else if ((psrtype & (2 << 29)) == (2 << 29)) > + mask = 0x03030303; > + else > + mask = 0; > + > + switch (hw->mac.type) { > + case ixgbe_mac_82599EB: > + case ixgbe_mac_X540: > + /* Read the appropriate portion of RETA */ > + for (i = 0; i < dwords; i++) > + reta[i] = IXGBE_READ_REG(hw, > + IXGBE_RETA(i + reta_offset_dw)); > + break; > + case ixgbe_mac_X550: > + case ixgbe_mac_X550EM_x: > + /* X550 has a per-VF RETA */ > + for (i = 0, j = reta_offset_dw; i < dwords; i++, j++) > + reta[i] = IXGBE_READ_REG(hw, > + IXGBE_PFVFRETA(j, vf)); > + break; > + default: > + return -1; > > There is no need to query the X550 info through the mailbox - this information can be obtained directly from the VF registers. I couldn't find an x550 spec anywhere. Could u tell me where it may be found? > > Thanks, > Emil > -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
>-----Original Message----- >From: Vlad Zolotarov [mailto:vladz@cloudius-systems.com] >Sent: Wednesday, March 25, 2015 12:22 PM >To: Tantilov, Emil S; netdev@vger.kernel.org >Cc: Kirsher, Jeffrey T; avi@cloudius-systems.com; gleb@cloudius-systems.com >Subject: Re: [PATCH net-next v7 3/7] ixgbe: Add a RETA query command to VF-PF channel API > > > >>On 03/25/15 20:03, Tantilov, Emil S wrote: <snip> >>There is no need to query the X550 info through the mailbox - this information can be obtained directly from the VF registers. > >Unfortunately I couldn't find a x550 spec anywhere. Could u give me a pointer to it? There is no official documentation for X550 out yet AFAIK, but you can see how the RSS key and redirection table are populated in ixgbevf - ixgbevf_setup_vfmrqc(). Basically the info is in the IXGBE_VFRSSRK/RETA registers. Or you can just strip the X550 related code from your patches and we'll take care of it once we agree on the implementation. Thanks, Emil -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 03/25/15 21:33, Tantilov, Emil S wrote: >> -----Original Message----- >> From: Vlad Zolotarov [mailto:vladz@cloudius-systems.com] >> Sent: Wednesday, March 25, 2015 12:22 PM >> To: Tantilov, Emil S; netdev@vger.kernel.org >> Cc: Kirsher, Jeffrey T; avi@cloudius-systems.com; gleb@cloudius-systems.com >> Subject: Re: [PATCH net-next v7 3/7] ixgbe: Add a RETA query command to VF-PF channel API >> >> >> >>> On 03/25/15 20:03, Tantilov, Emil S wrote: > > <snip> > >>> There is no need to query the X550 info through the mailbox - this information can be obtained directly from the VF registers. >> Unfortunately I couldn't find a x550 spec anywhere. Could u give me a pointer to it? > There is no official documentation for X550 out yet AFAIK, but you can see how the RSS key and redirection table are populated in ixgbevf - ixgbevf_setup_vfmrqc(). Basically the info is in the IXGBE_VFRSSRK/RETA registers. > > Or you can just strip the X550 related code from your patches and we'll take care of it once we agree on the implementation. I think I'll go for a second option since I can't check it anyway... ;) > > Thanks, > Emil > -- > To unsubscribe from this list: send the line "unsubscribe netdev" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h b/drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h index a5cb755..f9b5eae 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h @@ -73,6 +73,7 @@ enum ixgbe_pfvf_api_rev { ixgbe_mbox_api_10, /* API version 1.0, linux/freebsd VF driver */ ixgbe_mbox_api_20, /* API version 2.0, solaris Phase1 VF driver */ ixgbe_mbox_api_11, /* API version 1.1, linux/freebsd VF driver */ + ixgbe_mbox_api_12, /* API version 1.2, linux/freebsd VF driver */ /* This value should always be last */ ixgbe_mbox_api_unknown, /* indicates that API version is not known */ }; @@ -97,6 +98,13 @@ enum ixgbe_pfvf_api_rev { #define IXGBE_VF_TRANS_VLAN 3 /* Indication of port vlan */ #define IXGBE_VF_DEF_QUEUE 4 /* Default queue offset */ +/* mailbox API, version 1.2 VF requests */ +#define IXGBE_VF_GET_RETA 0x0a /* VF request for RETA */ + +/* GET_RETA request data indices within the mailbox */ +#define IXGBE_VF_RETA_SZ 1 /* Number of RETA DWs to bring */ +#define IXGBE_VF_RETA_OFFSET 2 /* Offset in RETA */ + /* length of permanent address message returned from PF */ #define IXGBE_VF_PERMADDR_MSG_LEN 4 /* word in permanent address message with the current multicast type */ diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c index 4d67677..301bb1b 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c @@ -437,6 +437,7 @@ static s32 ixgbe_set_vf_lpe(struct ixgbe_adapter *adapter, u32 *msgbuf, u32 vf) #endif /* CONFIG_FCOE */ switch (adapter->vfinfo[vf].vf_api) { case ixgbe_mbox_api_11: + case ixgbe_mbox_api_12: /* * Version 1.1 supports jumbo frames on VFs if PF has * jumbo frames enabled which means legacy VFs are @@ -904,6 +905,7 @@ static int ixgbe_negotiate_vf_api(struct ixgbe_adapter *adapter, switch (api) { case ixgbe_mbox_api_10: case ixgbe_mbox_api_11: + case ixgbe_mbox_api_12: adapter->vfinfo[vf].vf_api = api; return 0; default: @@ -927,6 +929,7 @@ static int ixgbe_get_vf_queues(struct ixgbe_adapter *adapter, switch (adapter->vfinfo[vf].vf_api) { case ixgbe_mbox_api_20: case ixgbe_mbox_api_11: + case ixgbe_mbox_api_12: break; default: return -1; @@ -954,6 +957,65 @@ static int ixgbe_get_vf_queues(struct ixgbe_adapter *adapter, return 0; } +static int ixgbe_get_vf_reta(struct ixgbe_adapter *adapter, u32 *msgbuf, u32 vf) +{ + struct ixgbe_hw *hw = &adapter->hw; + int i, j; + u32 *reta = &msgbuf[1]; + u32 mask = 0; + u32 psrtype; + u32 reta_offset_dw = msgbuf[IXGBE_VF_RETA_OFFSET]; + u32 dwords = msgbuf[IXGBE_VF_RETA_SZ]; + + /* verify the PF is supporting the correct API */ + if (!adapter->vfinfo[vf].rss_query_enabled || + (adapter->vfinfo[vf].vf_api != ixgbe_mbox_api_12)) + return -EPERM; + + psrtype = IXGBE_READ_REG(hw, IXGBE_PSRTYPE(vf)); + + /* The redirection table is composed as follows: + * 82598: 128 (8 bit wide) entries containing pair of 4 bit RSS indices + * 82599/X540: 128 (8 bit wide) entries containing 4 bit RSS index X550: + * 512 (8 bit wide) entries containing 6 bit RSS index + * + * PSRTYPE[n].RQPL defines if 0, 1 or 2 bits from the redirection table + * value should be used. + */ + + if ((psrtype & (1 << 29)) == (1 << 29)) + mask = 0x01010101; + else if ((psrtype & (2 << 29)) == (2 << 29)) + mask = 0x03030303; + else + mask = 0; + + switch (hw->mac.type) { + case ixgbe_mac_82599EB: + case ixgbe_mac_X540: + /* Read the appropriate portion of RETA */ + for (i = 0; i < dwords; i++) + reta[i] = IXGBE_READ_REG(hw, + IXGBE_RETA(i + reta_offset_dw)); + break; + case ixgbe_mac_X550: + case ixgbe_mac_X550EM_x: + /* X550 has a per-VF RETA */ + for (i = 0, j = reta_offset_dw; i < dwords; i++, j++) + reta[i] = IXGBE_READ_REG(hw, + IXGBE_PFVFRETA(j, vf)); + break; + default: + return -1; + } + + /* Mask the relevant bits */ + for (i = 0; i < dwords; i++) + reta[i] &= mask; + + return 0; +} + static int ixgbe_rcv_msg_from_vf(struct ixgbe_adapter *adapter, u32 vf) { u32 mbx_size = IXGBE_VFMAILBOX_SIZE; @@ -1010,6 +1072,9 @@ static int ixgbe_rcv_msg_from_vf(struct ixgbe_adapter *adapter, u32 vf) case IXGBE_VF_GET_QUEUES: retval = ixgbe_get_vf_queues(adapter, msgbuf, vf); break; + case IXGBE_VF_GET_RETA: + retval = ixgbe_get_vf_reta(adapter, msgbuf, vf); + break; default: e_err(drv, "Unhandled Msg %8.8x\n", msgbuf[0]); retval = IXGBE_ERR_MBX;
82599 and x540 VFs and PF share the same RSS redirection table (RETA). Therefore we just return it for all VFs. x550 on the other hand provides a separate redirection table for each VF (there is a per-pool RETA table). For 82599 and x540 RETA table is an array of 32 registers (128 bytes) and the maximum number of registers that may be delivered in a single VF-PF channel command is 15. Therefore we will deliver the whole table in 3 steps: 12, 12 and 8 registers in each step correspondingly. For x550 VFs RETA is a 64 byte array, so we may deliver it in two steps: 12 and 4 registers correspondingly. Thus this patch does the following: - Adds a new API version (to specify a new commands set). - Adds the IXGBE_VF_GET_RETA command to the VF-PF commands set. Signed-off-by: Vlad Zolotarov <vladz@cloudius-systems.com> --- New in v5: - Use the newly added netdev op to allow/prevent the RETA query on a per-VF basis. New in v4: - Deleted an empty line in ixgbe_get_vf_reta() switch-case. New in v3: - Pass the number of dwords and offset in RETA in the IXGBE_VF_GET_RETA request message. This allows to reduce the added command set to a single command. - Added a support for all devices supported by the ixgbe driver that have SR-IOV functions support: 82599, x540 and x550. The original code supported only 82599 and x540. - Added the masking of the RETA entries according to the PSRTYPE[n].RQPL value. New in v1 (compared to RFC): - Use "if-else" statement instead of a "switch-case" for a single option case (in ixgbe_get_vf_reta()). --- drivers/net/ethernet/intel/ixgbe/ixgbe_mbx.h | 8 ++++ drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c | 65 ++++++++++++++++++++++++++ 2 files changed, 73 insertions(+)