Message ID | 1423790080-8264-2-git-send-email-moritz.fischer@ettus.com |
---|---|
State | Needs Review / ACK, archived |
Headers | show |
Context | Check | Description |
---|---|---|
robh/checkpatch | warning | total: 1 errors, 0 warnings, 0 lines checked |
robh/patch-applied | success |
One nit below. On Thu, 2015-02-12 at 17:14 -0800, Moritz Fischer wrote: > Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> > --- > .../bindings/power/reset/e3x0-poweroff.txt | 16 ++++ > drivers/power/reset/Kconfig | 10 +++ > drivers/power/reset/Makefile | 1 + > drivers/power/reset/e3x0-poweroff.c | 94 ++++++++++++++++++++++ > 4 files changed, 121 insertions(+) > > diff --git a/Documentation/devicetree/bindings/power/reset/e3x0-poweroff.txt b/Documentation/devicetree/bindings/power/reset/e3x0-poweroff.txt > new file mode 100644 > index 0000000..df19998 > --- /dev/null > +++ b/Documentation/devicetree/bindings/power/reset/e3x0-poweroff.txt > @@ -0,0 +1,16 @@ > +National Instruments Ettus Research USRP E3x0 poweroff driver > + > +This module is part of the NI Ettus Research USRP E3x0 SDR. > + > +Required properties: > +- compatible: should be one of the following > + - "ettus,e3x0-poweroff": For devices such as the NI Ettus Research USRP E3x0 > +- reg: The registers to write to in order to trigger the poweroff. > + > +Note: Addresses may vary depending on the FPGA configuration > + > +Example: > + poweroff0: poweroff@40300000 { > + compatible = "ettus,e3x0-poweroff"; > + reg = <0x40300000 0x04>; > + }; > diff --git a/drivers/power/reset/Kconfig b/drivers/power/reset/Kconfig > index 27f6646..e45029f 100644 > --- a/drivers/power/reset/Kconfig > +++ b/drivers/power/reset/Kconfig > @@ -48,6 +48,16 @@ config POWER_RESET_BRCMSTB > Say Y here if you have a Broadcom STB board and you wish > to have restart support. > > +config POWER_RESET_E3X0 > + tristate "NI Ettus Research USRP E3x0 soft poweroff driver." > + default n > + help > + Say Y here to enable support for the NI Ettus Research > + USRP E3x0 soft poweroff. > + > + To compile this driver as a module, chose M here: the > + module will be called e3x0-reset. e3x0-poweroff > + > config POWER_RESET_GPIO > bool "GPIO power-off driver" > depends on OF_GPIO > diff --git a/drivers/power/reset/Makefile b/drivers/power/reset/Makefile > index 11de15b..eef50e9a 100644 > --- a/drivers/power/reset/Makefile > +++ b/drivers/power/reset/Makefile > @@ -3,6 +3,7 @@ obj-$(CONFIG_POWER_RESET_AT91_POWEROFF) += at91-poweroff.o > obj-$(CONFIG_POWER_RESET_AT91_RESET) += at91-reset.o > obj-$(CONFIG_POWER_RESET_AXXIA) += axxia-reset.o > obj-$(CONFIG_POWER_RESET_BRCMSTB) += brcmstb-reboot.o > +obj-$(CONFIG_POWER_RESET_E3X0) += e3x0-poweroff.o > obj-$(CONFIG_POWER_RESET_GPIO) += gpio-poweroff.o > obj-$(CONFIG_POWER_RESET_GPIO_RESTART) += gpio-restart.o > obj-$(CONFIG_POWER_RESET_HISI) += hisi-reboot.o Paul Bolle -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Paul, thanks for your feedback. Will incorporate the changes into the v2 when I'll resend. On Sun, Feb 15, 2015 at 12:32 PM, Paul Bolle <pebolle@tiscali.nl> wrote: > One nit below. > > On Thu, 2015-02-12 at 17:14 -0800, Moritz Fischer wrote: >> Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> >> --- >> .../bindings/power/reset/e3x0-poweroff.txt | 16 ++++ >> drivers/power/reset/Kconfig | 10 +++ >> drivers/power/reset/Makefile | 1 + >> drivers/power/reset/e3x0-poweroff.c | 94 ++++++++++++++++++++++ >> 4 files changed, 121 insertions(+) >> >> diff --git a/Documentation/devicetree/bindings/power/reset/e3x0-poweroff.txt b/Documentation/devicetree/bindings/power/reset/e3x0-poweroff.txt >> new file mode 100644 >> index 0000000..df19998 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/power/reset/e3x0-poweroff.txt >> @@ -0,0 +1,16 @@ >> +National Instruments Ettus Research USRP E3x0 poweroff driver >> + >> +This module is part of the NI Ettus Research USRP E3x0 SDR. >> + >> +Required properties: >> +- compatible: should be one of the following >> + - "ettus,e3x0-poweroff": For devices such as the NI Ettus Research USRP E3x0 >> +- reg: The registers to write to in order to trigger the poweroff. >> + >> +Note: Addresses may vary depending on the FPGA configuration >> + >> +Example: >> + poweroff0: poweroff@40300000 { >> + compatible = "ettus,e3x0-poweroff"; >> + reg = <0x40300000 0x04>; >> + }; >> diff --git a/drivers/power/reset/Kconfig b/drivers/power/reset/Kconfig >> index 27f6646..e45029f 100644 >> --- a/drivers/power/reset/Kconfig >> +++ b/drivers/power/reset/Kconfig >> @@ -48,6 +48,16 @@ config POWER_RESET_BRCMSTB >> Say Y here if you have a Broadcom STB board and you wish >> to have restart support. >> >> +config POWER_RESET_E3X0 >> + tristate "NI Ettus Research USRP E3x0 soft poweroff driver." >> + default n >> + help >> + Say Y here to enable support for the NI Ettus Research >> + USRP E3x0 soft poweroff. >> + >> + To compile this driver as a module, chose M here: the >> + module will be called e3x0-reset. > > e3x0-poweroff > >> + >> config POWER_RESET_GPIO >> bool "GPIO power-off driver" >> depends on OF_GPIO >> diff --git a/drivers/power/reset/Makefile b/drivers/power/reset/Makefile >> index 11de15b..eef50e9a 100644 >> --- a/drivers/power/reset/Makefile >> +++ b/drivers/power/reset/Makefile >> @@ -3,6 +3,7 @@ obj-$(CONFIG_POWER_RESET_AT91_POWEROFF) += at91-poweroff.o >> obj-$(CONFIG_POWER_RESET_AT91_RESET) += at91-reset.o >> obj-$(CONFIG_POWER_RESET_AXXIA) += axxia-reset.o >> obj-$(CONFIG_POWER_RESET_BRCMSTB) += brcmstb-reboot.o >> +obj-$(CONFIG_POWER_RESET_E3X0) += e3x0-poweroff.o >> obj-$(CONFIG_POWER_RESET_GPIO) += gpio-poweroff.o >> obj-$(CONFIG_POWER_RESET_GPIO_RESTART) += gpio-restart.o >> obj-$(CONFIG_POWER_RESET_HISI) += hisi-reboot.o > > > Paul Bolle > Moritz -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/power/reset/e3x0-poweroff.txt b/Documentation/devicetree/bindings/power/reset/e3x0-poweroff.txt new file mode 100644 index 0000000..df19998 --- /dev/null +++ b/Documentation/devicetree/bindings/power/reset/e3x0-poweroff.txt @@ -0,0 +1,16 @@ +National Instruments Ettus Research USRP E3x0 poweroff driver + +This module is part of the NI Ettus Research USRP E3x0 SDR. + +Required properties: +- compatible: should be one of the following + - "ettus,e3x0-poweroff": For devices such as the NI Ettus Research USRP E3x0 +- reg: The registers to write to in order to trigger the poweroff. + +Note: Addresses may vary depending on the FPGA configuration + +Example: + poweroff0: poweroff@40300000 { + compatible = "ettus,e3x0-poweroff"; + reg = <0x40300000 0x04>; + }; diff --git a/drivers/power/reset/Kconfig b/drivers/power/reset/Kconfig index 27f6646..e45029f 100644 --- a/drivers/power/reset/Kconfig +++ b/drivers/power/reset/Kconfig @@ -48,6 +48,16 @@ config POWER_RESET_BRCMSTB Say Y here if you have a Broadcom STB board and you wish to have restart support. +config POWER_RESET_E3X0 + tristate "NI Ettus Research USRP E3x0 soft poweroff driver." + default n + help + Say Y here to enable support for the NI Ettus Research + USRP E3x0 soft poweroff. + + To compile this driver as a module, chose M here: the + module will be called e3x0-reset. + config POWER_RESET_GPIO bool "GPIO power-off driver" depends on OF_GPIO diff --git a/drivers/power/reset/Makefile b/drivers/power/reset/Makefile index 11de15b..eef50e9a 100644 --- a/drivers/power/reset/Makefile +++ b/drivers/power/reset/Makefile @@ -3,6 +3,7 @@ obj-$(CONFIG_POWER_RESET_AT91_POWEROFF) += at91-poweroff.o obj-$(CONFIG_POWER_RESET_AT91_RESET) += at91-reset.o obj-$(CONFIG_POWER_RESET_AXXIA) += axxia-reset.o obj-$(CONFIG_POWER_RESET_BRCMSTB) += brcmstb-reboot.o +obj-$(CONFIG_POWER_RESET_E3X0) += e3x0-poweroff.o obj-$(CONFIG_POWER_RESET_GPIO) += gpio-poweroff.o obj-$(CONFIG_POWER_RESET_GPIO_RESTART) += gpio-restart.o obj-$(CONFIG_POWER_RESET_HISI) += hisi-reboot.o diff --git a/drivers/power/reset/e3x0-poweroff.c b/drivers/power/reset/e3x0-poweroff.c new file mode 100644 index 0000000..3e6778a --- /dev/null +++ b/drivers/power/reset/e3x0-poweroff.c @@ -0,0 +1,94 @@ +/* + * Copyright (c) 2015, National Instruments Corp. All rights reserved. + * + * Driver for NI Ettus Research USRP E3x0 soft power off. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/device.h> +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/of.h> + +static const u32 E3X0_POWEROFF_REG_OFFSET = 0x0; +static const u32 E3X0_POWEROFF_MAGIC = 0x7a; + +struct e3x0_poweroff { + struct device *dev; + void * __iomem io_addr; +}; + +static struct e3x0_poweroff *e3x0_poweroff; + +static void e3x0_pm_power_off(void) +{ + writel(E3X0_POWEROFF_MAGIC, + e3x0_poweroff->io_addr + E3X0_POWEROFF_REG_OFFSET); +} + +static int e3x0_poweroff_probe(struct platform_device *pdev) +{ + struct resource *res; + struct device *dev = &pdev->dev; + + e3x0_poweroff = devm_kzalloc(dev, sizeof(*e3x0_poweroff), + GFP_KERNEL); + if (!e3x0_poweroff) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + e3x0_poweroff->dev = dev; + e3x0_poweroff->io_addr = devm_ioremap_resource(dev, res); + if (IS_ERR(e3x0_poweroff->io_addr)) { + dev_err(dev, "Failed to ioremap registers\n"); + return PTR_ERR(e3x0_poweroff->io_addr); + } + + + if (!pm_power_off) + pm_power_off = e3x0_pm_power_off; + + return 0; +} + +static int e3x0_poweroff_remove(struct platform_device *pdev) +{ + if (pm_power_off == e3x0_pm_power_off) + pm_power_off = NULL; + e3x0_poweroff = NULL; + + return 0; +} + +#ifdef CONFIG_OF +static const struct of_device_id e3x0_poweroff_match[] = { + { .compatible = "ettus,e3x0-poweroff", }, + { }, +}; +MODULE_DEVICE_TABLE(of, e3x0_poweroff_match); +#endif + +static struct platform_driver e3x0_poweroff_driver = { + .driver = { + .name = "e3x0-poweroff", + .of_match_table = of_match_ptr(e3x0_poweroff_match), + }, + .probe = e3x0_poweroff_probe, + .remove = e3x0_poweroff_remove, +}; +module_platform_driver(e3x0_poweroff_driver); + +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Moritz Fischer <moritz.fischer@ettus.com>"); +MODULE_DESCRIPTION("NI Ettus Research USRP E3x0 soft-poweroff driver"); +MODULE_ALIAS("platform:e3x0-poweroff");
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com> --- .../bindings/power/reset/e3x0-poweroff.txt | 16 ++++ drivers/power/reset/Kconfig | 10 +++ drivers/power/reset/Makefile | 1 + drivers/power/reset/e3x0-poweroff.c | 94 ++++++++++++++++++++++ 4 files changed, 121 insertions(+)