Message ID | 1416068964-22529-4-git-send-email-maxime.hadjinlian@gmail.com |
---|---|
State | Accepted |
Headers | show |
Maxime, All, On 2014-11-15 17:29 +0100, Maxime Hadjinlian spake thusly: > Signed-off-by: Maxime Hadjinlian <maxime.hadjinlian@gmail.com> Acked-by: "Yann E. MORIN" <yann.morin.1998@free.fr> Regards, Yann E. MORIN. > --- > docs/manual/adding-packages-autotools.txt | 2 +- > docs/manual/faq-troubleshooting.txt | 8 ++++---- > 2 files changed, 5 insertions(+), 5 deletions(-) > > diff --git a/docs/manual/adding-packages-autotools.txt b/docs/manual/adding-packages-autotools.txt > index ece6c49..a041d91 100644 > --- a/docs/manual/adding-packages-autotools.txt > +++ b/docs/manual/adding-packages-autotools.txt > @@ -125,7 +125,7 @@ cases, typical packages will therefore only use a few of them. > variables to pass to the 'autoreconf' program if > +LIBFOO_AUTORECONF=YES+. These are passed in the environment of > the 'autoreconf' command. By default, empty. > - > + > * +LIBFOO_AUTORECONF_OPTS+ to specify additional options > passed to the 'autoreconf' program if > +LIBFOO_AUTORECONF=YES+. By default, empty. > diff --git a/docs/manual/faq-troubleshooting.txt b/docs/manual/faq-troubleshooting.txt > index 693028c..b30b4ac 100644 > --- a/docs/manual/faq-troubleshooting.txt > +++ b/docs/manual/faq-troubleshooting.txt > @@ -19,10 +19,10 @@ Starting dropbear sshd: generating rsa key... generating dsa key... OK > > then it means that your system is running, but didn't start a shell on > the serial console. In order to have the system start a shell on your > -serial console, you have to go into the Buildroot configuration, in > -+System configuration+, modify +Run a getty (login prompt) after boot+ > -and set the appropriate port and baud rate in the +getty options+ > -submenu. This will automatically tune the +/etc/inittab+ file of the > +serial console, you have to go into the Buildroot configuration, in > ++System configuration+, modify +Run a getty (login prompt) after boot+ > +and set the appropriate port and baud rate in the +getty options+ > +submenu. This will automatically tune the +/etc/inittab+ file of the > generated system so that a shell starts on the correct serial port. > > [[faq-no-compiler-on-target]] > -- > 2.1.3 > > _______________________________________________ > buildroot mailing list > buildroot@busybox.net > http://lists.busybox.net/mailman/listinfo/buildroot
Dear Maxime Hadjinlian, On Sat, 15 Nov 2014 17:29:19 +0100, Maxime Hadjinlian wrote: > Signed-off-by: Maxime Hadjinlian <maxime.hadjinlian@gmail.com> > --- > docs/manual/adding-packages-autotools.txt | 2 +- > docs/manual/faq-troubleshooting.txt | 8 ++++---- > 2 files changed, 5 insertions(+), 5 deletions(-) Applied to master, thanks. Thomas
diff --git a/docs/manual/adding-packages-autotools.txt b/docs/manual/adding-packages-autotools.txt index ece6c49..a041d91 100644 --- a/docs/manual/adding-packages-autotools.txt +++ b/docs/manual/adding-packages-autotools.txt @@ -125,7 +125,7 @@ cases, typical packages will therefore only use a few of them. variables to pass to the 'autoreconf' program if +LIBFOO_AUTORECONF=YES+. These are passed in the environment of the 'autoreconf' command. By default, empty. - + * +LIBFOO_AUTORECONF_OPTS+ to specify additional options passed to the 'autoreconf' program if +LIBFOO_AUTORECONF=YES+. By default, empty. diff --git a/docs/manual/faq-troubleshooting.txt b/docs/manual/faq-troubleshooting.txt index 693028c..b30b4ac 100644 --- a/docs/manual/faq-troubleshooting.txt +++ b/docs/manual/faq-troubleshooting.txt @@ -19,10 +19,10 @@ Starting dropbear sshd: generating rsa key... generating dsa key... OK then it means that your system is running, but didn't start a shell on the serial console. In order to have the system start a shell on your -serial console, you have to go into the Buildroot configuration, in -+System configuration+, modify +Run a getty (login prompt) after boot+ -and set the appropriate port and baud rate in the +getty options+ -submenu. This will automatically tune the +/etc/inittab+ file of the +serial console, you have to go into the Buildroot configuration, in ++System configuration+, modify +Run a getty (login prompt) after boot+ +and set the appropriate port and baud rate in the +getty options+ +submenu. This will automatically tune the +/etc/inittab+ file of the generated system so that a shell starts on the correct serial port. [[faq-no-compiler-on-target]]
Signed-off-by: Maxime Hadjinlian <maxime.hadjinlian@gmail.com> --- docs/manual/adding-packages-autotools.txt | 2 +- docs/manual/faq-troubleshooting.txt | 8 ++++---- 2 files changed, 5 insertions(+), 5 deletions(-)