Message ID | 1406021138-5545-1-git-send-email-josh.wu@atmel.com |
---|---|
State | Changes Requested |
Headers | show |
On Tue, Jul 22, 2014 at 05:25:38PM +0800, Josh Wu wrote: > diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c > index 33826a0..012d687 100644 > --- a/drivers/mtd/nand/atmel_nand.c > +++ b/drivers/mtd/nand/atmel_nand.c > @@ -1913,15 +1913,13 @@ static int nfc_sram_write_page(struct mtd_info *mtd, struct nand_chip *chip, > if (offset || (data_len < mtd->writesize)) > return -EINVAL; > > - cfg = nfc_readl(host->nfc->hsmc_regs, CFG); > - len = mtd->writesize; > - > - if (unlikely(raw)) { > - len += mtd->oobsize; > - nfc_writel(host->nfc->hsmc_regs, CFG, cfg | NFC_CFG_WSPARE); > - } else > - nfc_writel(host->nfc->hsmc_regs, CFG, cfg & ~NFC_CFG_WSPARE); > + if (data_len > mtd->writesize) { > + dev_err(host->dev, "data_len: %d should not bigger than mtd->writesize: %d!\n", "should not be" > + data_len, mtd->writesize); > + return -EINVAL; > + } The NAND layer guarantees that 'write_page' will never have to write more than 1 page (mtd->writesize), so the above block seems unnecessary. Drop it? > > + len = mtd->writesize; > /* Copy page data to sram that will write to nand via NFC */ > if (use_dma) { > if (atmel_nand_dma_op(mtd, (void *)buf, len, 0) != 0) > @@ -1931,6 +1929,15 @@ static int nfc_sram_write_page(struct mtd_info *mtd, struct nand_chip *chip, > memcpy32_toio(sram, buf, len); > } > > + cfg = nfc_readl(host->nfc->hsmc_regs, CFG); > + if (unlikely(raw) && oob_required) { > + memcpy32_toio(sram + len, chip->oob_poi, mtd->oobsize); > + len += mtd->oobsize; > + nfc_writel(host->nfc->hsmc_regs, CFG, cfg | NFC_CFG_WSPARE); > + } else { > + nfc_writel(host->nfc->hsmc_regs, CFG, cfg & ~NFC_CFG_WSPARE); > + } > + > if (chip->ecc.mode == NAND_ECC_HW && host->has_pmecc) > /* > * When use NFC sram, need set up PMECC before send Brian
On 8/5/2014 5:22 AM, Brian Norris wrote: > On Tue, Jul 22, 2014 at 05:25:38PM +0800, Josh Wu wrote: >> diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c >> index 33826a0..012d687 100644 >> --- a/drivers/mtd/nand/atmel_nand.c >> +++ b/drivers/mtd/nand/atmel_nand.c >> @@ -1913,15 +1913,13 @@ static int nfc_sram_write_page(struct mtd_info *mtd, struct nand_chip *chip, >> if (offset || (data_len < mtd->writesize)) >> return -EINVAL; >> >> - cfg = nfc_readl(host->nfc->hsmc_regs, CFG); >> - len = mtd->writesize; >> - >> - if (unlikely(raw)) { >> - len += mtd->oobsize; >> - nfc_writel(host->nfc->hsmc_regs, CFG, cfg | NFC_CFG_WSPARE); >> - } else >> - nfc_writel(host->nfc->hsmc_regs, CFG, cfg & ~NFC_CFG_WSPARE); >> + if (data_len > mtd->writesize) { >> + dev_err(host->dev, "data_len: %d should not bigger than mtd->writesize: %d!\n", > "should not be" > >> + data_len, mtd->writesize); >> + return -EINVAL; >> + } > The NAND layer guarantees that 'write_page' will never have to write > more than 1 page (mtd->writesize), so the above block seems unnecessary. > Drop it? you are right. I sent a v2 version which drops this check. Thanks. Best Regards, Josh Wu > >> >> + len = mtd->writesize; >> /* Copy page data to sram that will write to nand via NFC */ >> if (use_dma) { >> if (atmel_nand_dma_op(mtd, (void *)buf, len, 0) != 0) >> @@ -1931,6 +1929,15 @@ static int nfc_sram_write_page(struct mtd_info *mtd, struct nand_chip *chip, >> memcpy32_toio(sram, buf, len); >> } >> >> + cfg = nfc_readl(host->nfc->hsmc_regs, CFG); >> + if (unlikely(raw) && oob_required) { >> + memcpy32_toio(sram + len, chip->oob_poi, mtd->oobsize); >> + len += mtd->oobsize; >> + nfc_writel(host->nfc->hsmc_regs, CFG, cfg | NFC_CFG_WSPARE); >> + } else { >> + nfc_writel(host->nfc->hsmc_regs, CFG, cfg & ~NFC_CFG_WSPARE); >> + } >> + >> if (chip->ecc.mode == NAND_ECC_HW && host->has_pmecc) >> /* >> * When use NFC sram, need set up PMECC before send > Brian
diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c index 33826a0..012d687 100644 --- a/drivers/mtd/nand/atmel_nand.c +++ b/drivers/mtd/nand/atmel_nand.c @@ -1913,15 +1913,13 @@ static int nfc_sram_write_page(struct mtd_info *mtd, struct nand_chip *chip, if (offset || (data_len < mtd->writesize)) return -EINVAL; - cfg = nfc_readl(host->nfc->hsmc_regs, CFG); - len = mtd->writesize; - - if (unlikely(raw)) { - len += mtd->oobsize; - nfc_writel(host->nfc->hsmc_regs, CFG, cfg | NFC_CFG_WSPARE); - } else - nfc_writel(host->nfc->hsmc_regs, CFG, cfg & ~NFC_CFG_WSPARE); + if (data_len > mtd->writesize) { + dev_err(host->dev, "data_len: %d should not bigger than mtd->writesize: %d!\n", + data_len, mtd->writesize); + return -EINVAL; + } + len = mtd->writesize; /* Copy page data to sram that will write to nand via NFC */ if (use_dma) { if (atmel_nand_dma_op(mtd, (void *)buf, len, 0) != 0) @@ -1931,6 +1929,15 @@ static int nfc_sram_write_page(struct mtd_info *mtd, struct nand_chip *chip, memcpy32_toio(sram, buf, len); } + cfg = nfc_readl(host->nfc->hsmc_regs, CFG); + if (unlikely(raw) && oob_required) { + memcpy32_toio(sram + len, chip->oob_poi, mtd->oobsize); + len += mtd->oobsize; + nfc_writel(host->nfc->hsmc_regs, CFG, cfg | NFC_CFG_WSPARE); + } else { + nfc_writel(host->nfc->hsmc_regs, CFG, cfg & ~NFC_CFG_WSPARE); + } + if (chip->ecc.mode == NAND_ECC_HW && host->has_pmecc) /* * When use NFC sram, need set up PMECC before send
When enable NFC sram write, it will failed the mtd_nandbiterrs.ko test. As in driver's nfc_sram_write_page(), if ops->mode equal to MTD_OSP_RAW, driver assumes the data buffer contains one page data and one oob data followed. And driver will write the page data and oob data to nand. But this is wrong implementation. Since the data buffer don't contains the oob data to write. We should write the chip->oob_poi to nand's oob. So this patch fix it by writing the oob data from chip->oob_poi. Signed-off-by: Josh Wu <josh.wu@atmel.com> --- drivers/mtd/nand/atmel_nand.c | 23 +++++++++++++++-------- 1 file changed, 15 insertions(+), 8 deletions(-)