Message ID | 1360893205-12004-1-git-send-email-iwamatsu@nigauri.org |
---|---|
State | Changes Requested, archived |
Delegated to: | David Miller |
Headers | show |
On 2/15/13, Nobuhiro Iwamatsu <iwamatsu@nigauri.org> wrote: > From: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> > > This adds support of device tree probe for Renesas sh-ether driver. > > Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> > > V4: - Remove empty sh_eth_parse_dt(). > V3: - Removed sentnece of "needs-init" from document. > V2: - Removed ether_setup(). > - Fixed typo from "sh-etn" to "sh-eth". > - Removed "needs-init" and sh-eth,endian from definition of DT. > - Changed "sh-eth,edmac-endian" instead of "sh-eth,edmac-big-endain" > in definition of DT. > --- > Documentation/devicetree/bindings/net/sh_ether.txt | 39 +++++ > drivers/net/ethernet/renesas/sh_eth.c | 150 > ++++++++++++++++---- > 2 files changed, 165 insertions(+), 24 deletions(-) > create mode 100644 Documentation/devicetree/bindings/net/sh_ether.txt > > diff --git a/Documentation/devicetree/bindings/net/sh_ether.txt > b/Documentation/devicetree/bindings/net/sh_ether.txt > new file mode 100644 > index 0000000..f20d66a > --- /dev/null > +++ b/Documentation/devicetree/bindings/net/sh_ether.txt > @@ -0,0 +1,39 @@ > +* Renesas Electronics SuperH EMAC > + > +This file provides information, what the device node > +for the sh_eth interface contains. > + > +Required properties: > +- compatible: "renesas,sh-eth"; > +- interrupt-parent: The phandle for the interrupt controller > that > + services interrupts for this device. > +- reg: Offset and length of the register set for > the > + device. > +- interrupts: Interrupt mapping for the sh_eth interrupt > + sources (vector id). > +- phy-mode: String, operation mode of the PHY > interface. > +- sh-eth,register-type: String, register type of sh_eth. > + Please select "gigabit", "fast-sh4" or > + "fast-sh3-sh2". > +- sh-eth,phy-id: PHY id. > + > +Optional properties: > +- local-mac-address: 6 bytes, mac address > +- sh-eth,no-ether-link: Set link control by software. When device > does > + not support ether-link, set. > +- sh-eth,ether-link-active-low: Set link check method. > + When detection of link is treated as > active-low, > + set. > +- sh-eth,edmac-big-endian: Set big endian for sh_eth dmac. > + It work as little endian when this is not > set. > + > +Example (armadillo800eva): > + sh-eth@e9a00000 { > + compatible = "renesas,sh-eth"; > + interrupt-parent = <&intca>; > + reg = <0xe9a00000 0x800>, <0xe9a01800 0x800>; > + interrupts = <0x500>; > + phy-mode = "mii"; > + sh-eth,register-type = "gigabit"; > + sh-eth,phy-id = <0>; > + }; > diff --git a/drivers/net/ethernet/renesas/sh_eth.c > b/drivers/net/ethernet/renesas/sh_eth.c > index 3d70586..b41249a 100644 > --- a/drivers/net/ethernet/renesas/sh_eth.c > +++ b/drivers/net/ethernet/renesas/sh_eth.c > @@ -1,7 +1,7 @@ > /* > * SuperH Ethernet device driver > * > - * Copyright (C) 2006-2012 Nobuhiro Iwamatsu > + * Copyright (C) 2006-2013 Nobuhiro Iwamatsu > * Copyright (C) 2008-2012 Renesas Solutions Corp. > * > * This program is free software; you can redistribute it and/or modify > it > @@ -31,6 +31,12 @@ > #include <linux/platform_device.h> > #include <linux/mdio-bitbang.h> > #include <linux/netdevice.h> > +#include <linux/of.h> > +#include <linux/of_device.h> > +#include <linux/of_platform.h> > +#include <linux/of_address.h> > +#include <linux/of_irq.h> > +#include <linux/of_net.h> > #include <linux/phy.h> > #include <linux/cache.h> > #include <linux/io.h> > @@ -2347,26 +2353,103 @@ static const struct net_device_ops > sh_eth_netdev_ops = { > .ndo_change_mtu = eth_change_mtu, > }; > > +#ifdef CONFIG_OF > + > +static int > +sh_eth_of_get_register_type(struct device_node *np) > +{ > + const char *of_str; > + int ret = of_property_read_string(np, "sh-eth,register-type", &of_str); > + if (ret) > + return ret; > + > + if (of_str && !strcmp(of_str, "gigabit")) > + return SH_ETH_REG_GIGABIT; > + > + else if (of_str && !strcmp(of_str, "fast-sh4")) > + return SH_ETH_REG_FAST_SH4; > + else if (of_str && !strcmp(of_str, "fast-sh3-sh2")) > + return SH_ETH_REG_FAST_SH3_SH2; > + else > + return -EINVAL; > +} > + > +static struct sh_eth_plat_data * > +sh_eth_parse_dt(struct device *dev, struct net_device *ndev) > +{ > + int ret; > + struct device_node *np = dev->of_node; > + struct sh_eth_plat_data *pdata; > + > + pdata = devm_kzalloc(dev, sizeof(struct sh_eth_plat_data), > + GFP_KERNEL); > + if (!pdata) { > + dev_err(dev, "%s: failed to allocate config data\n", __func__); > + return NULL; > + } > + > + pdata->phy_interface = of_get_phy_mode(np); > + > + of_property_read_u32(np, "sh-eth,phy-id", &pdata->phy); > + > + if (of_find_property(np, "sh-eth,edmac-big-endian", NULL)) > + pdata->edmac_endian = EDMAC_BIG_ENDIAN; > + else > + pdata->edmac_endian = EDMAC_LITTLE_ENDIAN; > + > + if (of_find_property(np, "sh-eth,no-ether-link", NULL)) > + pdata->no_ether_link = 1; > + else > + pdata->no_ether_link = 0; > + > + if (of_find_property(np, "sh-eth,ether-link-active-low", NULL)) > + pdata->ether_link_active_low = 1; > + else > + pdata->ether_link_active_low = 0; > + > + ret = sh_eth_of_get_register_type(np); > + if (ret < 0) > + goto error; > + pdata->register_type = ret; > + > +#ifdef CONFIG_OF_NET > + if (!is_valid_ether_addr(ndev->dev_addr)) { > + const char *macaddr = of_get_mac_address(np); > + if (macaddr) > + memcpy(pdata->mac_addr, macaddr, ETH_ALEN); > + } > +#endif > + > + return pdata; > + > +error: > + devm_kfree(dev, pdata); > + return NULL; > +} > +#endif > + > static int sh_eth_drv_probe(struct platform_device *pdev) > { > - int ret, devno = 0; > + int ret = 0, devno = 0; > struct resource *res; > struct net_device *ndev = NULL; > struct sh_eth_private *mdp = NULL; > struct sh_eth_plat_data *pd; > + struct device_node *np = pdev->dev.of_node; > + > + ndev = alloc_etherdev(sizeof(struct sh_eth_private)); > + if (!ndev) { > + ret = -ENOMEM; > + goto out; > + } > > + mdp = netdev_priv(ndev); > /* get base addr */ > res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > if (unlikely(res == NULL)) { > dev_err(&pdev->dev, "invalid resource\n"); > ret = -EINVAL; > - goto out; > - } > - > - ndev = alloc_etherdev(sizeof(struct sh_eth_private)); > - if (!ndev) { > - ret = -ENOMEM; > - goto out; > + goto out_release; > } > > /* The sh Ether-specific entries in the device structure. */ > @@ -2383,27 +2466,41 @@ static int sh_eth_drv_probe(struct platform_device > *pdev) > } > ndev->irq = ret; > > - SET_NETDEV_DEV(ndev, &pdev->dev); > - > - /* Fill in the fields of the device structure with ethernet values. */ > - ether_setup(ndev); > - > - mdp = netdev_priv(ndev); > - mdp->num_tx_ring = TX_RING_SIZE; > - mdp->num_rx_ring = RX_RING_SIZE; > mdp->addr = ioremap(res->start, resource_size(res)); > if (mdp->addr == NULL) { > ret = -ENOMEM; > dev_err(&pdev->dev, "ioremap failed.\n"); > goto out_release; > } > +#ifdef CONFIG_OF > + if (np && of_device_is_available(np)) { > + pd = sh_eth_parse_dt(&pdev->dev, ndev); > + if (pdev->dev.platform_data) { > + struct sh_eth_plat_data *tmp = > + pdev->dev.platform_data; > + pd->set_mdio_gate = tmp->set_mdio_gate; > + pd->needs_init = tmp->needs_init; > + } > + } else > +#endif > + pd = (struct sh_eth_plat_data *)(pdev->dev.platform_data); > + > + if (!pd) { > + dev_err(&pdev->dev, "no setup data defined\n"); > + ret = -EINVAL; > + goto out_release; > + } > + > + SET_NETDEV_DEV(ndev, &pdev->dev); > + > + mdp->num_tx_ring = TX_RING_SIZE; > + mdp->num_rx_ring = RX_RING_SIZE; > > spin_lock_init(&mdp->lock); > mdp->pdev = pdev; > pm_runtime_enable(&pdev->dev); > pm_runtime_resume(&pdev->dev); > > - pd = (struct sh_eth_plat_data *)(pdev->dev.platform_data); > /* get PHY ID */ > mdp->phy_id = pd->phy; > mdp->phy_interface = pd->phy_interface; > @@ -2412,6 +2509,8 @@ static int sh_eth_drv_probe(struct platform_device > *pdev) > mdp->no_ether_link = pd->no_ether_link; > mdp->ether_link_active_low = pd->ether_link_active_low; > mdp->reg_offset = sh_eth_get_register_offset(pd->register_type); > + /* read and set MAC address */ > + read_mac_address(ndev, pd->mac_addr); > > /* set cpu data */ > #if defined(SH_ETH_HAS_BOTH_MODULES) > @@ -2429,20 +2528,16 @@ static int sh_eth_drv_probe(struct platform_device > *pdev) > /* debug message level */ > mdp->msg_enable = SH_ETH_DEF_MSG_ENABLE; > > - /* read and set MAC address */ > - read_mac_address(ndev, pd->mac_addr); > - > /* ioremap the TSU registers */ > if (mdp->cd->tsu) { > struct resource *rtsu; > rtsu = platform_get_resource(pdev, IORESOURCE_MEM, 1); > if (!rtsu) { > dev_err(&pdev->dev, "Not found TSU resource\n"); > - ret = -ENODEV; > goto out_release; > } > mdp->tsu_addr = ioremap(rtsu->start, > - resource_size(rtsu)); > + resource_size(rtsu)); > mdp->port = devno % 2; > ndev->features = NETIF_F_HW_VLAN_FILTER; > } > @@ -2522,17 +2617,24 @@ static int sh_eth_runtime_nop(struct device *dev) > return 0; > } > > -static struct dev_pm_ops sh_eth_dev_pm_ops = { CONFIG_PM? > +static const struct dev_pm_ops sh_eth_dev_pm_ops = { > .runtime_suspend = sh_eth_runtime_nop, > .runtime_resume = sh_eth_runtime_nop, > }; > > +static struct of_device_id sh_eth_match[] = { You have missed the const specifier here > + { .compatible = "renesas,sh-eth",}, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, sh_eth_match); > + if CONFIG_OF is not defined it's not needed. > static struct platform_driver sh_eth_driver = { > .probe = sh_eth_drv_probe, > .remove = sh_eth_drv_remove, > .driver = { > .name = CARDNAME, > .pm = &sh_eth_dev_pm_ops, > + .of_match_table = sh_eth_match, > }, > }; > > -- > 1.7.10.4 > > -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Fri, Feb 15, 2013 at 10:53:25AM +0900, Nobuhiro Iwamatsu wrote: > From: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> > > This adds support of device tree probe for Renesas sh-ether driver. Hi Iwamatsu-san, I do not expect this code to go through the renesas tree. However, in order to provide a basis for work on renesas SoCs I have added this patch to the topic/sh_eth topic branch in the reneas tree on kernel.org and merged it into topic/all+next. In other words, I am not picking this patch up to merge it or add it to linux-next, rather I am storing it for reference. Also, I do note that there have already been some comments made on this patch and I plan to date topic/sh_eth topic branch as new versions are posted. > Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> > > V4: - Remove empty sh_eth_parse_dt(). > V3: - Removed sentnece of "needs-init" from document. > V2: - Removed ether_setup(). > - Fixed typo from "sh-etn" to "sh-eth". > - Removed "needs-init" and sh-eth,endian from definition of DT. > - Changed "sh-eth,edmac-endian" instead of "sh-eth,edmac-big-endain" > in definition of DT. > --- > Documentation/devicetree/bindings/net/sh_ether.txt | 39 +++++ > drivers/net/ethernet/renesas/sh_eth.c | 150 ++++++++++++++++---- > 2 files changed, 165 insertions(+), 24 deletions(-) > create mode 100644 Documentation/devicetree/bindings/net/sh_ether.txt > > diff --git a/Documentation/devicetree/bindings/net/sh_ether.txt b/Documentation/devicetree/bindings/net/sh_ether.txt > new file mode 100644 > index 0000000..f20d66a > --- /dev/null > +++ b/Documentation/devicetree/bindings/net/sh_ether.txt > @@ -0,0 +1,39 @@ > +* Renesas Electronics SuperH EMAC > + > +This file provides information, what the device node > +for the sh_eth interface contains. > + > +Required properties: > +- compatible: "renesas,sh-eth"; > +- interrupt-parent: The phandle for the interrupt controller that > + services interrupts for this device. > +- reg: Offset and length of the register set for the > + device. > +- interrupts: Interrupt mapping for the sh_eth interrupt > + sources (vector id). > +- phy-mode: String, operation mode of the PHY interface. > +- sh-eth,register-type: String, register type of sh_eth. > + Please select "gigabit", "fast-sh4" or > + "fast-sh3-sh2". > +- sh-eth,phy-id: PHY id. > + > +Optional properties: > +- local-mac-address: 6 bytes, mac address > +- sh-eth,no-ether-link: Set link control by software. When device does > + not support ether-link, set. > +- sh-eth,ether-link-active-low: Set link check method. > + When detection of link is treated as active-low, > + set. > +- sh-eth,edmac-big-endian: Set big endian for sh_eth dmac. > + It work as little endian when this is not set. > + > +Example (armadillo800eva): > + sh-eth@e9a00000 { > + compatible = "renesas,sh-eth"; > + interrupt-parent = <&intca>; > + reg = <0xe9a00000 0x800>, <0xe9a01800 0x800>; > + interrupts = <0x500>; > + phy-mode = "mii"; > + sh-eth,register-type = "gigabit"; > + sh-eth,phy-id = <0>; > + }; > diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c > index 3d70586..b41249a 100644 > --- a/drivers/net/ethernet/renesas/sh_eth.c > +++ b/drivers/net/ethernet/renesas/sh_eth.c > @@ -1,7 +1,7 @@ > /* > * SuperH Ethernet device driver > * > - * Copyright (C) 2006-2012 Nobuhiro Iwamatsu > + * Copyright (C) 2006-2013 Nobuhiro Iwamatsu > * Copyright (C) 2008-2012 Renesas Solutions Corp. > * > * This program is free software; you can redistribute it and/or modify it > @@ -31,6 +31,12 @@ > #include <linux/platform_device.h> > #include <linux/mdio-bitbang.h> > #include <linux/netdevice.h> > +#include <linux/of.h> > +#include <linux/of_device.h> > +#include <linux/of_platform.h> > +#include <linux/of_address.h> > +#include <linux/of_irq.h> > +#include <linux/of_net.h> > #include <linux/phy.h> > #include <linux/cache.h> > #include <linux/io.h> > @@ -2347,26 +2353,103 @@ static const struct net_device_ops sh_eth_netdev_ops = { > .ndo_change_mtu = eth_change_mtu, > }; > > +#ifdef CONFIG_OF > + > +static int > +sh_eth_of_get_register_type(struct device_node *np) > +{ > + const char *of_str; > + int ret = of_property_read_string(np, "sh-eth,register-type", &of_str); > + if (ret) > + return ret; > + > + if (of_str && !strcmp(of_str, "gigabit")) > + return SH_ETH_REG_GIGABIT; > + > + else if (of_str && !strcmp(of_str, "fast-sh4")) > + return SH_ETH_REG_FAST_SH4; > + else if (of_str && !strcmp(of_str, "fast-sh3-sh2")) > + return SH_ETH_REG_FAST_SH3_SH2; > + else > + return -EINVAL; > +} > + > +static struct sh_eth_plat_data * > +sh_eth_parse_dt(struct device *dev, struct net_device *ndev) > +{ > + int ret; > + struct device_node *np = dev->of_node; > + struct sh_eth_plat_data *pdata; > + > + pdata = devm_kzalloc(dev, sizeof(struct sh_eth_plat_data), > + GFP_KERNEL); > + if (!pdata) { > + dev_err(dev, "%s: failed to allocate config data\n", __func__); > + return NULL; > + } > + > + pdata->phy_interface = of_get_phy_mode(np); > + > + of_property_read_u32(np, "sh-eth,phy-id", &pdata->phy); > + > + if (of_find_property(np, "sh-eth,edmac-big-endian", NULL)) > + pdata->edmac_endian = EDMAC_BIG_ENDIAN; > + else > + pdata->edmac_endian = EDMAC_LITTLE_ENDIAN; > + > + if (of_find_property(np, "sh-eth,no-ether-link", NULL)) > + pdata->no_ether_link = 1; > + else > + pdata->no_ether_link = 0; > + > + if (of_find_property(np, "sh-eth,ether-link-active-low", NULL)) > + pdata->ether_link_active_low = 1; > + else > + pdata->ether_link_active_low = 0; > + > + ret = sh_eth_of_get_register_type(np); > + if (ret < 0) > + goto error; > + pdata->register_type = ret; > + > +#ifdef CONFIG_OF_NET > + if (!is_valid_ether_addr(ndev->dev_addr)) { > + const char *macaddr = of_get_mac_address(np); > + if (macaddr) > + memcpy(pdata->mac_addr, macaddr, ETH_ALEN); > + } > +#endif > + > + return pdata; > + > +error: > + devm_kfree(dev, pdata); > + return NULL; > +} > +#endif > + > static int sh_eth_drv_probe(struct platform_device *pdev) > { > - int ret, devno = 0; > + int ret = 0, devno = 0; > struct resource *res; > struct net_device *ndev = NULL; > struct sh_eth_private *mdp = NULL; > struct sh_eth_plat_data *pd; > + struct device_node *np = pdev->dev.of_node; > + > + ndev = alloc_etherdev(sizeof(struct sh_eth_private)); > + if (!ndev) { > + ret = -ENOMEM; > + goto out; > + } > > + mdp = netdev_priv(ndev); > /* get base addr */ > res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > if (unlikely(res == NULL)) { > dev_err(&pdev->dev, "invalid resource\n"); > ret = -EINVAL; > - goto out; > - } > - > - ndev = alloc_etherdev(sizeof(struct sh_eth_private)); > - if (!ndev) { > - ret = -ENOMEM; > - goto out; > + goto out_release; > } > > /* The sh Ether-specific entries in the device structure. */ > @@ -2383,27 +2466,41 @@ static int sh_eth_drv_probe(struct platform_device *pdev) > } > ndev->irq = ret; > > - SET_NETDEV_DEV(ndev, &pdev->dev); > - > - /* Fill in the fields of the device structure with ethernet values. */ > - ether_setup(ndev); > - > - mdp = netdev_priv(ndev); > - mdp->num_tx_ring = TX_RING_SIZE; > - mdp->num_rx_ring = RX_RING_SIZE; > mdp->addr = ioremap(res->start, resource_size(res)); > if (mdp->addr == NULL) { > ret = -ENOMEM; > dev_err(&pdev->dev, "ioremap failed.\n"); > goto out_release; > } > +#ifdef CONFIG_OF > + if (np && of_device_is_available(np)) { > + pd = sh_eth_parse_dt(&pdev->dev, ndev); > + if (pdev->dev.platform_data) { > + struct sh_eth_plat_data *tmp = > + pdev->dev.platform_data; > + pd->set_mdio_gate = tmp->set_mdio_gate; > + pd->needs_init = tmp->needs_init; > + } > + } else > +#endif > + pd = (struct sh_eth_plat_data *)(pdev->dev.platform_data); > + > + if (!pd) { > + dev_err(&pdev->dev, "no setup data defined\n"); > + ret = -EINVAL; > + goto out_release; > + } > + > + SET_NETDEV_DEV(ndev, &pdev->dev); > + > + mdp->num_tx_ring = TX_RING_SIZE; > + mdp->num_rx_ring = RX_RING_SIZE; > > spin_lock_init(&mdp->lock); > mdp->pdev = pdev; > pm_runtime_enable(&pdev->dev); > pm_runtime_resume(&pdev->dev); > > - pd = (struct sh_eth_plat_data *)(pdev->dev.platform_data); > /* get PHY ID */ > mdp->phy_id = pd->phy; > mdp->phy_interface = pd->phy_interface; > @@ -2412,6 +2509,8 @@ static int sh_eth_drv_probe(struct platform_device *pdev) > mdp->no_ether_link = pd->no_ether_link; > mdp->ether_link_active_low = pd->ether_link_active_low; > mdp->reg_offset = sh_eth_get_register_offset(pd->register_type); > + /* read and set MAC address */ > + read_mac_address(ndev, pd->mac_addr); > > /* set cpu data */ > #if defined(SH_ETH_HAS_BOTH_MODULES) > @@ -2429,20 +2528,16 @@ static int sh_eth_drv_probe(struct platform_device *pdev) > /* debug message level */ > mdp->msg_enable = SH_ETH_DEF_MSG_ENABLE; > > - /* read and set MAC address */ > - read_mac_address(ndev, pd->mac_addr); > - > /* ioremap the TSU registers */ > if (mdp->cd->tsu) { > struct resource *rtsu; > rtsu = platform_get_resource(pdev, IORESOURCE_MEM, 1); > if (!rtsu) { > dev_err(&pdev->dev, "Not found TSU resource\n"); > - ret = -ENODEV; > goto out_release; > } > mdp->tsu_addr = ioremap(rtsu->start, > - resource_size(rtsu)); > + resource_size(rtsu)); > mdp->port = devno % 2; > ndev->features = NETIF_F_HW_VLAN_FILTER; > } > @@ -2522,17 +2617,24 @@ static int sh_eth_runtime_nop(struct device *dev) > return 0; > } > > -static struct dev_pm_ops sh_eth_dev_pm_ops = { > +static const struct dev_pm_ops sh_eth_dev_pm_ops = { > .runtime_suspend = sh_eth_runtime_nop, > .runtime_resume = sh_eth_runtime_nop, > }; > > +static struct of_device_id sh_eth_match[] = { > + { .compatible = "renesas,sh-eth",}, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, sh_eth_match); > + > static struct platform_driver sh_eth_driver = { > .probe = sh_eth_drv_probe, > .remove = sh_eth_drv_remove, > .driver = { > .name = CARDNAME, > .pm = &sh_eth_dev_pm_ops, > + .of_match_table = sh_eth_match, > }, > }; > > -- > 1.7.10.4 > > -- > To unsubscribe from this list: send the line "unsubscribe netdev" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
(2013/02/16 0:02), Denis Kirjanov wrote: > On 2/15/13, Nobuhiro Iwamatsu<iwamatsu@nigauri.org> wrote: >> From: Nobuhiro Iwamatsu<nobuhiro.iwamatsu.yj@renesas.com> >> >> This adds support of device tree probe for Renesas sh-ether driver. >> >> Signed-off-by: Nobuhiro Iwamatsu<nobuhiro.iwamatsu.yj@renesas.com> >> >> V4: - Remove empty sh_eth_parse_dt(). >> V3: - Removed sentnece of "needs-init" from document. >> V2: - Removed ether_setup(). >> - Fixed typo from "sh-etn" to "sh-eth". >> - Removed "needs-init" and sh-eth,endian from definition of DT. >> - Changed "sh-eth,edmac-endian" instead of "sh-eth,edmac-big-endain" >> in definition of DT. >> --- >> Documentation/devicetree/bindings/net/sh_ether.txt | 39 +++++ >> drivers/net/ethernet/renesas/sh_eth.c | 150 >> ++++++++++++++++---- >> 2 files changed, 165 insertions(+), 24 deletions(-) >> create mode 100644 Documentation/devicetree/bindings/net/sh_ether.txt >> <snip> >> diff --git a/drivers/net/ethernet/renesas/sh_eth.c >> b/drivers/net/ethernet/renesas/sh_eth.c >> index 3d70586..b41249a 100644 >> --- a/drivers/net/ethernet/renesas/sh_eth.c >> +++ b/drivers/net/ethernet/renesas/sh_eth.c >> @@ -1,7 +1,7 @@ >> /* >> * SuperH Ethernet device driver >> * >> - * Copyright (C) 2006-2012 Nobuhiro Iwamatsu >> + * Copyright (C) 2006-2013 Nobuhiro Iwamatsu >> * Copyright (C) 2008-2012 Renesas Solutions Corp. >> * >> * This program is free software; you can redistribute it and/or modify >> it >> @@ -31,6 +31,12 @@ >> #include<linux/platform_device.h> >> #include<linux/mdio-bitbang.h> >> #include<linux/netdevice.h> >> +#include<linux/of.h> >> +#include<linux/of_device.h> >> +#include<linux/of_platform.h> >> +#include<linux/of_address.h> >> +#include<linux/of_irq.h> >> +#include<linux/of_net.h> >> #include<linux/phy.h> >> #include<linux/cache.h> >> #include<linux/io.h> >> @@ -2347,26 +2353,103 @@ static const struct net_device_ops >> sh_eth_netdev_ops = { >> .ndo_change_mtu = eth_change_mtu, >> }; >> >> +#ifdef CONFIG_OF >> + >> +static int >> +sh_eth_of_get_register_type(struct device_node *np) >> +{ >> + const char *of_str; >> + int ret = of_property_read_string(np, "sh-eth,register-type",&of_str); >> + if (ret) >> + return ret; >> + >> + if (of_str&& !strcmp(of_str, "gigabit")) >> + return SH_ETH_REG_GIGABIT; >> + >> + else if (of_str&& !strcmp(of_str, "fast-sh4")) >> + return SH_ETH_REG_FAST_SH4; >> + else if (of_str&& !strcmp(of_str, "fast-sh3-sh2")) >> + return SH_ETH_REG_FAST_SH3_SH2; >> + else >> + return -EINVAL; >> +} >> + >> +static struct sh_eth_plat_data * >> +sh_eth_parse_dt(struct device *dev, struct net_device *ndev) >> +{ >> + int ret; >> + struct device_node *np = dev->of_node; >> + struct sh_eth_plat_data *pdata; >> + >> + pdata = devm_kzalloc(dev, sizeof(struct sh_eth_plat_data), >> + GFP_KERNEL); >> + if (!pdata) { >> + dev_err(dev, "%s: failed to allocate config data\n", __func__); >> + return NULL; >> + } >> + >> + pdata->phy_interface = of_get_phy_mode(np); >> + >> + of_property_read_u32(np, "sh-eth,phy-id",&pdata->phy); >> + >> + if (of_find_property(np, "sh-eth,edmac-big-endian", NULL)) >> + pdata->edmac_endian = EDMAC_BIG_ENDIAN; >> + else >> + pdata->edmac_endian = EDMAC_LITTLE_ENDIAN; >> + >> + if (of_find_property(np, "sh-eth,no-ether-link", NULL)) >> + pdata->no_ether_link = 1; >> + else >> + pdata->no_ether_link = 0; >> + >> + if (of_find_property(np, "sh-eth,ether-link-active-low", NULL)) >> + pdata->ether_link_active_low = 1; >> + else >> + pdata->ether_link_active_low = 0; >> + >> + ret = sh_eth_of_get_register_type(np); >> + if (ret< 0) >> + goto error; >> + pdata->register_type = ret; >> + >> +#ifdef CONFIG_OF_NET >> + if (!is_valid_ether_addr(ndev->dev_addr)) { >> + const char *macaddr = of_get_mac_address(np); >> + if (macaddr) >> + memcpy(pdata->mac_addr, macaddr, ETH_ALEN); >> + } >> +#endif >> + >> + return pdata; >> + >> +error: >> + devm_kfree(dev, pdata); >> + return NULL; >> +} >> +#endif >> + >> static int sh_eth_drv_probe(struct platform_device *pdev) >> { >> - int ret, devno = 0; >> + int ret = 0, devno = 0; >> struct resource *res; >> struct net_device *ndev = NULL; >> struct sh_eth_private *mdp = NULL; >> struct sh_eth_plat_data *pd; >> + struct device_node *np = pdev->dev.of_node; >> + >> + ndev = alloc_etherdev(sizeof(struct sh_eth_private)); >> + if (!ndev) { >> + ret = -ENOMEM; >> + goto out; >> + } >> >> + mdp = netdev_priv(ndev); >> /* get base addr */ >> res = platform_get_resource(pdev, IORESOURCE_MEM, 0); >> if (unlikely(res == NULL)) { >> dev_err(&pdev->dev, "invalid resource\n"); >> ret = -EINVAL; >> - goto out; >> - } >> - >> - ndev = alloc_etherdev(sizeof(struct sh_eth_private)); >> - if (!ndev) { >> - ret = -ENOMEM; >> - goto out; >> + goto out_release; >> } >> >> /* The sh Ether-specific entries in the device structure. */ >> @@ -2383,27 +2466,41 @@ static int sh_eth_drv_probe(struct platform_device >> *pdev) >> } >> ndev->irq = ret; >> >> - SET_NETDEV_DEV(ndev,&pdev->dev); >> - >> - /* Fill in the fields of the device structure with ethernet values. */ >> - ether_setup(ndev); >> - >> - mdp = netdev_priv(ndev); >> - mdp->num_tx_ring = TX_RING_SIZE; >> - mdp->num_rx_ring = RX_RING_SIZE; >> mdp->addr = ioremap(res->start, resource_size(res)); >> if (mdp->addr == NULL) { >> ret = -ENOMEM; >> dev_err(&pdev->dev, "ioremap failed.\n"); >> goto out_release; >> } >> +#ifdef CONFIG_OF >> + if (np&& of_device_is_available(np)) { >> + pd = sh_eth_parse_dt(&pdev->dev, ndev); >> + if (pdev->dev.platform_data) { >> + struct sh_eth_plat_data *tmp = >> + pdev->dev.platform_data; >> + pd->set_mdio_gate = tmp->set_mdio_gate; >> + pd->needs_init = tmp->needs_init; >> + } >> + } else >> +#endif >> + pd = (struct sh_eth_plat_data *)(pdev->dev.platform_data); >> + >> + if (!pd) { >> + dev_err(&pdev->dev, "no setup data defined\n"); >> + ret = -EINVAL; >> + goto out_release; >> + } >> + >> + SET_NETDEV_DEV(ndev,&pdev->dev); >> + >> + mdp->num_tx_ring = TX_RING_SIZE; >> + mdp->num_rx_ring = RX_RING_SIZE; >> >> spin_lock_init(&mdp->lock); >> mdp->pdev = pdev; >> pm_runtime_enable(&pdev->dev); >> pm_runtime_resume(&pdev->dev); >> >> - pd = (struct sh_eth_plat_data *)(pdev->dev.platform_data); >> /* get PHY ID */ >> mdp->phy_id = pd->phy; >> mdp->phy_interface = pd->phy_interface; >> @@ -2412,6 +2509,8 @@ static int sh_eth_drv_probe(struct platform_device >> *pdev) >> mdp->no_ether_link = pd->no_ether_link; >> mdp->ether_link_active_low = pd->ether_link_active_low; >> mdp->reg_offset = sh_eth_get_register_offset(pd->register_type); >> + /* read and set MAC address */ >> + read_mac_address(ndev, pd->mac_addr); >> >> /* set cpu data */ >> #if defined(SH_ETH_HAS_BOTH_MODULES) >> @@ -2429,20 +2528,16 @@ static int sh_eth_drv_probe(struct platform_device >> *pdev) >> /* debug message level */ >> mdp->msg_enable = SH_ETH_DEF_MSG_ENABLE; >> >> - /* read and set MAC address */ >> - read_mac_address(ndev, pd->mac_addr); >> - >> /* ioremap the TSU registers */ >> if (mdp->cd->tsu) { >> struct resource *rtsu; >> rtsu = platform_get_resource(pdev, IORESOURCE_MEM, 1); >> if (!rtsu) { >> dev_err(&pdev->dev, "Not found TSU resource\n"); >> - ret = -ENODEV; >> goto out_release; >> } >> mdp->tsu_addr = ioremap(rtsu->start, >> - resource_size(rtsu)); >> + resource_size(rtsu)); >> mdp->port = devno % 2; >> ndev->features = NETIF_F_HW_VLAN_FILTER; >> } >> @@ -2522,17 +2617,24 @@ static int sh_eth_runtime_nop(struct device *dev) >> return 0; >> } >> >> -static struct dev_pm_ops sh_eth_dev_pm_ops = { > CONFIG_PM? Yes, I will add this. > >> +static const struct dev_pm_ops sh_eth_dev_pm_ops = { >> .runtime_suspend = sh_eth_runtime_nop, >> .runtime_resume = sh_eth_runtime_nop, >> }; >> >> +static struct of_device_id sh_eth_match[] = { > > You have missed the const specifier here OK, I will fix. > >> + { .compatible = "renesas,sh-eth",}, >> + {}, >> +}; >> +MODULE_DEVICE_TABLE(of, sh_eth_match); >> + > > if CONFIG_OF is not defined it's not needed. > OK, I will add CONFIG_OF and update platform_driver. >> static struct platform_driver sh_eth_driver = { >> .probe = sh_eth_drv_probe, >> .remove = sh_eth_drv_remove, >> .driver = { >> .name = CARDNAME, >> .pm =&sh_eth_dev_pm_ops, >> + .of_match_table = sh_eth_match, >> }, >> }; Thank you for your review. Best regards, Nobuhiro -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi, Simon. Thanks for the supporting. I understood. Best regards, Nobuhiro (2013/02/16 11:26), Simon Horman wrote: > On Fri, Feb 15, 2013 at 10:53:25AM +0900, Nobuhiro Iwamatsu wrote: >> From: Nobuhiro Iwamatsu<nobuhiro.iwamatsu.yj@renesas.com> >> >> This adds support of device tree probe for Renesas sh-ether driver. > > Hi Iwamatsu-san, > > I do not expect this code to go through the renesas tree. However, in > order to provide a basis for work on renesas SoCs I have added this patch > to the topic/sh_eth topic branch in the reneas tree on kernel.org and > merged it into topic/all+next. > > In other words, I am not picking this patch up to merge it or add it to > linux-next, rather I am storing it for reference. > > Also, I do note that there have already been some comments made on this > patch and I plan to date topic/sh_eth topic branch as new versions are > posted. > >> Signed-off-by: Nobuhiro Iwamatsu<nobuhiro.iwamatsu.yj@renesas.com> >> >> V4: - Remove empty sh_eth_parse_dt(). >> V3: - Removed sentnece of "needs-init" from document. >> V2: - Removed ether_setup(). >> - Fixed typo from "sh-etn" to "sh-eth". >> - Removed "needs-init" and sh-eth,endian from definition of DT. >> - Changed "sh-eth,edmac-endian" instead of "sh-eth,edmac-big-endain" >> in definition of DT. >> --- >> Documentation/devicetree/bindings/net/sh_ether.txt | 39 +++++ >> drivers/net/ethernet/renesas/sh_eth.c | 150 ++++++++++++++++---- >> 2 files changed, 165 insertions(+), 24 deletions(-) >> create mode 100644 Documentation/devicetree/bindings/net/sh_ether.txt >> >> diff --git a/Documentation/devicetree/bindings/net/sh_ether.txt b/Documentation/devicetree/bindings/net/sh_ether.txt >> new file mode 100644 >> index 0000000..f20d66a >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/net/sh_ether.txt >> @@ -0,0 +1,39 @@ >> +* Renesas Electronics SuperH EMAC >> + >> +This file provides information, what the device node >> +for the sh_eth interface contains. >> + >> +Required properties: >> +- compatible: "renesas,sh-eth"; >> +- interrupt-parent: The phandle for the interrupt controller that >> + services interrupts for this device. >> +- reg: Offset and length of the register set for the >> + device. >> +- interrupts: Interrupt mapping for the sh_eth interrupt >> + sources (vector id). >> +- phy-mode: String, operation mode of the PHY interface. >> +- sh-eth,register-type: String, register type of sh_eth. >> + Please select "gigabit", "fast-sh4" or >> + "fast-sh3-sh2". >> +- sh-eth,phy-id: PHY id. >> + >> +Optional properties: >> +- local-mac-address: 6 bytes, mac address >> +- sh-eth,no-ether-link: Set link control by software. When device does >> + not support ether-link, set. >> +- sh-eth,ether-link-active-low: Set link check method. >> + When detection of link is treated as active-low, >> + set. >> +- sh-eth,edmac-big-endian: Set big endian for sh_eth dmac. >> + It work as little endian when this is not set. >> + >> +Example (armadillo800eva): >> + sh-eth@e9a00000 { >> + compatible = "renesas,sh-eth"; >> + interrupt-parent =<&intca>; >> + reg =<0xe9a00000 0x800>,<0xe9a01800 0x800>; >> + interrupts =<0x500>; >> + phy-mode = "mii"; >> + sh-eth,register-type = "gigabit"; >> + sh-eth,phy-id =<0>; >> + }; >> diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c >> index 3d70586..b41249a 100644 >> --- a/drivers/net/ethernet/renesas/sh_eth.c >> +++ b/drivers/net/ethernet/renesas/sh_eth.c >> @@ -1,7 +1,7 @@ >> /* >> * SuperH Ethernet device driver >> * >> - * Copyright (C) 2006-2012 Nobuhiro Iwamatsu >> + * Copyright (C) 2006-2013 Nobuhiro Iwamatsu >> * Copyright (C) 2008-2012 Renesas Solutions Corp. >> * >> * This program is free software; you can redistribute it and/or modify it >> @@ -31,6 +31,12 @@ >> #include<linux/platform_device.h> >> #include<linux/mdio-bitbang.h> >> #include<linux/netdevice.h> >> +#include<linux/of.h> >> +#include<linux/of_device.h> >> +#include<linux/of_platform.h> >> +#include<linux/of_address.h> >> +#include<linux/of_irq.h> >> +#include<linux/of_net.h> >> #include<linux/phy.h> >> #include<linux/cache.h> >> #include<linux/io.h> >> @@ -2347,26 +2353,103 @@ static const struct net_device_ops sh_eth_netdev_ops = { >> .ndo_change_mtu = eth_change_mtu, >> }; >> >> +#ifdef CONFIG_OF >> + >> +static int >> +sh_eth_of_get_register_type(struct device_node *np) >> +{ >> + const char *of_str; >> + int ret = of_property_read_string(np, "sh-eth,register-type",&of_str); >> + if (ret) >> + return ret; >> + >> + if (of_str&& !strcmp(of_str, "gigabit")) >> + return SH_ETH_REG_GIGABIT; >> + >> + else if (of_str&& !strcmp(of_str, "fast-sh4")) >> + return SH_ETH_REG_FAST_SH4; >> + else if (of_str&& !strcmp(of_str, "fast-sh3-sh2")) >> + return SH_ETH_REG_FAST_SH3_SH2; >> + else >> + return -EINVAL; >> +} >> + >> +static struct sh_eth_plat_data * >> +sh_eth_parse_dt(struct device *dev, struct net_device *ndev) >> +{ >> + int ret; >> + struct device_node *np = dev->of_node; >> + struct sh_eth_plat_data *pdata; >> + >> + pdata = devm_kzalloc(dev, sizeof(struct sh_eth_plat_data), >> + GFP_KERNEL); >> + if (!pdata) { >> + dev_err(dev, "%s: failed to allocate config data\n", __func__); >> + return NULL; >> + } >> + >> + pdata->phy_interface = of_get_phy_mode(np); >> + >> + of_property_read_u32(np, "sh-eth,phy-id",&pdata->phy); >> + >> + if (of_find_property(np, "sh-eth,edmac-big-endian", NULL)) >> + pdata->edmac_endian = EDMAC_BIG_ENDIAN; >> + else >> + pdata->edmac_endian = EDMAC_LITTLE_ENDIAN; >> + >> + if (of_find_property(np, "sh-eth,no-ether-link", NULL)) >> + pdata->no_ether_link = 1; >> + else >> + pdata->no_ether_link = 0; >> + >> + if (of_find_property(np, "sh-eth,ether-link-active-low", NULL)) >> + pdata->ether_link_active_low = 1; >> + else >> + pdata->ether_link_active_low = 0; >> + >> + ret = sh_eth_of_get_register_type(np); >> + if (ret< 0) >> + goto error; >> + pdata->register_type = ret; >> + >> +#ifdef CONFIG_OF_NET >> + if (!is_valid_ether_addr(ndev->dev_addr)) { >> + const char *macaddr = of_get_mac_address(np); >> + if (macaddr) >> + memcpy(pdata->mac_addr, macaddr, ETH_ALEN); >> + } >> +#endif >> + >> + return pdata; >> + >> +error: >> + devm_kfree(dev, pdata); >> + return NULL; >> +} >> +#endif >> + >> static int sh_eth_drv_probe(struct platform_device *pdev) >> { >> - int ret, devno = 0; >> + int ret = 0, devno = 0; >> struct resource *res; >> struct net_device *ndev = NULL; >> struct sh_eth_private *mdp = NULL; >> struct sh_eth_plat_data *pd; >> + struct device_node *np = pdev->dev.of_node; >> + >> + ndev = alloc_etherdev(sizeof(struct sh_eth_private)); >> + if (!ndev) { >> + ret = -ENOMEM; >> + goto out; >> + } >> >> + mdp = netdev_priv(ndev); >> /* get base addr */ >> res = platform_get_resource(pdev, IORESOURCE_MEM, 0); >> if (unlikely(res == NULL)) { >> dev_err(&pdev->dev, "invalid resource\n"); >> ret = -EINVAL; >> - goto out; >> - } >> - >> - ndev = alloc_etherdev(sizeof(struct sh_eth_private)); >> - if (!ndev) { >> - ret = -ENOMEM; >> - goto out; >> + goto out_release; >> } >> >> /* The sh Ether-specific entries in the device structure. */ >> @@ -2383,27 +2466,41 @@ static int sh_eth_drv_probe(struct platform_device *pdev) >> } >> ndev->irq = ret; >> >> - SET_NETDEV_DEV(ndev,&pdev->dev); >> - >> - /* Fill in the fields of the device structure with ethernet values. */ >> - ether_setup(ndev); >> - >> - mdp = netdev_priv(ndev); >> - mdp->num_tx_ring = TX_RING_SIZE; >> - mdp->num_rx_ring = RX_RING_SIZE; >> mdp->addr = ioremap(res->start, resource_size(res)); >> if (mdp->addr == NULL) { >> ret = -ENOMEM; >> dev_err(&pdev->dev, "ioremap failed.\n"); >> goto out_release; >> } >> +#ifdef CONFIG_OF >> + if (np&& of_device_is_available(np)) { >> + pd = sh_eth_parse_dt(&pdev->dev, ndev); >> + if (pdev->dev.platform_data) { >> + struct sh_eth_plat_data *tmp = >> + pdev->dev.platform_data; >> + pd->set_mdio_gate = tmp->set_mdio_gate; >> + pd->needs_init = tmp->needs_init; >> + } >> + } else >> +#endif >> + pd = (struct sh_eth_plat_data *)(pdev->dev.platform_data); >> + >> + if (!pd) { >> + dev_err(&pdev->dev, "no setup data defined\n"); >> + ret = -EINVAL; >> + goto out_release; >> + } >> + >> + SET_NETDEV_DEV(ndev,&pdev->dev); >> + >> + mdp->num_tx_ring = TX_RING_SIZE; >> + mdp->num_rx_ring = RX_RING_SIZE; >> >> spin_lock_init(&mdp->lock); >> mdp->pdev = pdev; >> pm_runtime_enable(&pdev->dev); >> pm_runtime_resume(&pdev->dev); >> >> - pd = (struct sh_eth_plat_data *)(pdev->dev.platform_data); >> /* get PHY ID */ >> mdp->phy_id = pd->phy; >> mdp->phy_interface = pd->phy_interface; >> @@ -2412,6 +2509,8 @@ static int sh_eth_drv_probe(struct platform_device *pdev) >> mdp->no_ether_link = pd->no_ether_link; >> mdp->ether_link_active_low = pd->ether_link_active_low; >> mdp->reg_offset = sh_eth_get_register_offset(pd->register_type); >> + /* read and set MAC address */ >> + read_mac_address(ndev, pd->mac_addr); >> >> /* set cpu data */ >> #if defined(SH_ETH_HAS_BOTH_MODULES) >> @@ -2429,20 +2528,16 @@ static int sh_eth_drv_probe(struct platform_device *pdev) >> /* debug message level */ >> mdp->msg_enable = SH_ETH_DEF_MSG_ENABLE; >> >> - /* read and set MAC address */ >> - read_mac_address(ndev, pd->mac_addr); >> - >> /* ioremap the TSU registers */ >> if (mdp->cd->tsu) { >> struct resource *rtsu; >> rtsu = platform_get_resource(pdev, IORESOURCE_MEM, 1); >> if (!rtsu) { >> dev_err(&pdev->dev, "Not found TSU resource\n"); >> - ret = -ENODEV; >> goto out_release; >> } >> mdp->tsu_addr = ioremap(rtsu->start, >> - resource_size(rtsu)); >> + resource_size(rtsu)); >> mdp->port = devno % 2; >> ndev->features = NETIF_F_HW_VLAN_FILTER; >> } >> @@ -2522,17 +2617,24 @@ static int sh_eth_runtime_nop(struct device *dev) >> return 0; >> } >> >> -static struct dev_pm_ops sh_eth_dev_pm_ops = { >> +static const struct dev_pm_ops sh_eth_dev_pm_ops = { >> .runtime_suspend = sh_eth_runtime_nop, >> .runtime_resume = sh_eth_runtime_nop, >> }; >> >> +static struct of_device_id sh_eth_match[] = { >> + { .compatible = "renesas,sh-eth",}, >> + {}, >> +}; >> +MODULE_DEVICE_TABLE(of, sh_eth_match); >> + >> static struct platform_driver sh_eth_driver = { >> .probe = sh_eth_drv_probe, >> .remove = sh_eth_drv_remove, >> .driver = { >> .name = CARDNAME, >> .pm =&sh_eth_dev_pm_ops, >> + .of_match_table = sh_eth_match, >> }, >> }; >> >> -- >> 1.7.10.4 >> >> -- >> To unsubscribe from this list: send the line "unsubscribe netdev" in >> the body of a message to majordomo@vger.kernel.org >> More majordomo info at http://vger.kernel.org/majordomo-info.html >> > -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/net/sh_ether.txt b/Documentation/devicetree/bindings/net/sh_ether.txt new file mode 100644 index 0000000..f20d66a --- /dev/null +++ b/Documentation/devicetree/bindings/net/sh_ether.txt @@ -0,0 +1,39 @@ +* Renesas Electronics SuperH EMAC + +This file provides information, what the device node +for the sh_eth interface contains. + +Required properties: +- compatible: "renesas,sh-eth"; +- interrupt-parent: The phandle for the interrupt controller that + services interrupts for this device. +- reg: Offset and length of the register set for the + device. +- interrupts: Interrupt mapping for the sh_eth interrupt + sources (vector id). +- phy-mode: String, operation mode of the PHY interface. +- sh-eth,register-type: String, register type of sh_eth. + Please select "gigabit", "fast-sh4" or + "fast-sh3-sh2". +- sh-eth,phy-id: PHY id. + +Optional properties: +- local-mac-address: 6 bytes, mac address +- sh-eth,no-ether-link: Set link control by software. When device does + not support ether-link, set. +- sh-eth,ether-link-active-low: Set link check method. + When detection of link is treated as active-low, + set. +- sh-eth,edmac-big-endian: Set big endian for sh_eth dmac. + It work as little endian when this is not set. + +Example (armadillo800eva): + sh-eth@e9a00000 { + compatible = "renesas,sh-eth"; + interrupt-parent = <&intca>; + reg = <0xe9a00000 0x800>, <0xe9a01800 0x800>; + interrupts = <0x500>; + phy-mode = "mii"; + sh-eth,register-type = "gigabit"; + sh-eth,phy-id = <0>; + }; diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index 3d70586..b41249a 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -1,7 +1,7 @@ /* * SuperH Ethernet device driver * - * Copyright (C) 2006-2012 Nobuhiro Iwamatsu + * Copyright (C) 2006-2013 Nobuhiro Iwamatsu * Copyright (C) 2008-2012 Renesas Solutions Corp. * * This program is free software; you can redistribute it and/or modify it @@ -31,6 +31,12 @@ #include <linux/platform_device.h> #include <linux/mdio-bitbang.h> #include <linux/netdevice.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/of_platform.h> +#include <linux/of_address.h> +#include <linux/of_irq.h> +#include <linux/of_net.h> #include <linux/phy.h> #include <linux/cache.h> #include <linux/io.h> @@ -2347,26 +2353,103 @@ static const struct net_device_ops sh_eth_netdev_ops = { .ndo_change_mtu = eth_change_mtu, }; +#ifdef CONFIG_OF + +static int +sh_eth_of_get_register_type(struct device_node *np) +{ + const char *of_str; + int ret = of_property_read_string(np, "sh-eth,register-type", &of_str); + if (ret) + return ret; + + if (of_str && !strcmp(of_str, "gigabit")) + return SH_ETH_REG_GIGABIT; + + else if (of_str && !strcmp(of_str, "fast-sh4")) + return SH_ETH_REG_FAST_SH4; + else if (of_str && !strcmp(of_str, "fast-sh3-sh2")) + return SH_ETH_REG_FAST_SH3_SH2; + else + return -EINVAL; +} + +static struct sh_eth_plat_data * +sh_eth_parse_dt(struct device *dev, struct net_device *ndev) +{ + int ret; + struct device_node *np = dev->of_node; + struct sh_eth_plat_data *pdata; + + pdata = devm_kzalloc(dev, sizeof(struct sh_eth_plat_data), + GFP_KERNEL); + if (!pdata) { + dev_err(dev, "%s: failed to allocate config data\n", __func__); + return NULL; + } + + pdata->phy_interface = of_get_phy_mode(np); + + of_property_read_u32(np, "sh-eth,phy-id", &pdata->phy); + + if (of_find_property(np, "sh-eth,edmac-big-endian", NULL)) + pdata->edmac_endian = EDMAC_BIG_ENDIAN; + else + pdata->edmac_endian = EDMAC_LITTLE_ENDIAN; + + if (of_find_property(np, "sh-eth,no-ether-link", NULL)) + pdata->no_ether_link = 1; + else + pdata->no_ether_link = 0; + + if (of_find_property(np, "sh-eth,ether-link-active-low", NULL)) + pdata->ether_link_active_low = 1; + else + pdata->ether_link_active_low = 0; + + ret = sh_eth_of_get_register_type(np); + if (ret < 0) + goto error; + pdata->register_type = ret; + +#ifdef CONFIG_OF_NET + if (!is_valid_ether_addr(ndev->dev_addr)) { + const char *macaddr = of_get_mac_address(np); + if (macaddr) + memcpy(pdata->mac_addr, macaddr, ETH_ALEN); + } +#endif + + return pdata; + +error: + devm_kfree(dev, pdata); + return NULL; +} +#endif + static int sh_eth_drv_probe(struct platform_device *pdev) { - int ret, devno = 0; + int ret = 0, devno = 0; struct resource *res; struct net_device *ndev = NULL; struct sh_eth_private *mdp = NULL; struct sh_eth_plat_data *pd; + struct device_node *np = pdev->dev.of_node; + + ndev = alloc_etherdev(sizeof(struct sh_eth_private)); + if (!ndev) { + ret = -ENOMEM; + goto out; + } + mdp = netdev_priv(ndev); /* get base addr */ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (unlikely(res == NULL)) { dev_err(&pdev->dev, "invalid resource\n"); ret = -EINVAL; - goto out; - } - - ndev = alloc_etherdev(sizeof(struct sh_eth_private)); - if (!ndev) { - ret = -ENOMEM; - goto out; + goto out_release; } /* The sh Ether-specific entries in the device structure. */ @@ -2383,27 +2466,41 @@ static int sh_eth_drv_probe(struct platform_device *pdev) } ndev->irq = ret; - SET_NETDEV_DEV(ndev, &pdev->dev); - - /* Fill in the fields of the device structure with ethernet values. */ - ether_setup(ndev); - - mdp = netdev_priv(ndev); - mdp->num_tx_ring = TX_RING_SIZE; - mdp->num_rx_ring = RX_RING_SIZE; mdp->addr = ioremap(res->start, resource_size(res)); if (mdp->addr == NULL) { ret = -ENOMEM; dev_err(&pdev->dev, "ioremap failed.\n"); goto out_release; } +#ifdef CONFIG_OF + if (np && of_device_is_available(np)) { + pd = sh_eth_parse_dt(&pdev->dev, ndev); + if (pdev->dev.platform_data) { + struct sh_eth_plat_data *tmp = + pdev->dev.platform_data; + pd->set_mdio_gate = tmp->set_mdio_gate; + pd->needs_init = tmp->needs_init; + } + } else +#endif + pd = (struct sh_eth_plat_data *)(pdev->dev.platform_data); + + if (!pd) { + dev_err(&pdev->dev, "no setup data defined\n"); + ret = -EINVAL; + goto out_release; + } + + SET_NETDEV_DEV(ndev, &pdev->dev); + + mdp->num_tx_ring = TX_RING_SIZE; + mdp->num_rx_ring = RX_RING_SIZE; spin_lock_init(&mdp->lock); mdp->pdev = pdev; pm_runtime_enable(&pdev->dev); pm_runtime_resume(&pdev->dev); - pd = (struct sh_eth_plat_data *)(pdev->dev.platform_data); /* get PHY ID */ mdp->phy_id = pd->phy; mdp->phy_interface = pd->phy_interface; @@ -2412,6 +2509,8 @@ static int sh_eth_drv_probe(struct platform_device *pdev) mdp->no_ether_link = pd->no_ether_link; mdp->ether_link_active_low = pd->ether_link_active_low; mdp->reg_offset = sh_eth_get_register_offset(pd->register_type); + /* read and set MAC address */ + read_mac_address(ndev, pd->mac_addr); /* set cpu data */ #if defined(SH_ETH_HAS_BOTH_MODULES) @@ -2429,20 +2528,16 @@ static int sh_eth_drv_probe(struct platform_device *pdev) /* debug message level */ mdp->msg_enable = SH_ETH_DEF_MSG_ENABLE; - /* read and set MAC address */ - read_mac_address(ndev, pd->mac_addr); - /* ioremap the TSU registers */ if (mdp->cd->tsu) { struct resource *rtsu; rtsu = platform_get_resource(pdev, IORESOURCE_MEM, 1); if (!rtsu) { dev_err(&pdev->dev, "Not found TSU resource\n"); - ret = -ENODEV; goto out_release; } mdp->tsu_addr = ioremap(rtsu->start, - resource_size(rtsu)); + resource_size(rtsu)); mdp->port = devno % 2; ndev->features = NETIF_F_HW_VLAN_FILTER; } @@ -2522,17 +2617,24 @@ static int sh_eth_runtime_nop(struct device *dev) return 0; } -static struct dev_pm_ops sh_eth_dev_pm_ops = { +static const struct dev_pm_ops sh_eth_dev_pm_ops = { .runtime_suspend = sh_eth_runtime_nop, .runtime_resume = sh_eth_runtime_nop, }; +static struct of_device_id sh_eth_match[] = { + { .compatible = "renesas,sh-eth",}, + {}, +}; +MODULE_DEVICE_TABLE(of, sh_eth_match); + static struct platform_driver sh_eth_driver = { .probe = sh_eth_drv_probe, .remove = sh_eth_drv_remove, .driver = { .name = CARDNAME, .pm = &sh_eth_dev_pm_ops, + .of_match_table = sh_eth_match, }, };