| Message ID | 20240608141633.2562-3-laurent.pinchart@ideasonboard.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | ADP5585 GPIO expander, PWM and keypad controller support | expand |
Sat, Jun 08, 2024 at 05:16:31PM +0300, Laurent Pinchart kirjoitti: > From: Haibo Chen <haibo.chen@nxp.com> > > The ADP5585 is a 10/11 input/output port expander with a built in keypad > matrix decoder, programmable logic, reset generator, and PWM generator. > This driver supports the chip by modelling it as an MFD device, with two > child devices for the GPIO and PWM functions. > > The driver is derived from an initial implementation from NXP, available > in commit 8059835bee19 ("MLK-25917-1 mfd: adp5585: add ADI adp5585 core > support") in their BSP kernel tree. It has been extensively rewritten. ... > +#include <linux/array_size.h> > +#include <linux/device.h> + err.h > +#include <linux/i2c.h> > +#include <linux/mfd/adp5585.h> > +#include <linux/mfd/core.h> > +#include <linux/mod_devicetable.h> > +#include <linux/module.h> > +#include <linux/regmap.h> > +#include <linux/types.h> ... > +static const struct mfd_cell adp5585_devs[] = { > + { .name = "adp5585-gpio", }, > + { .name = "adp5585-pwm", }, Inner commas are not needed. > +}; ... > +#define ADP5585_Rx_PULL_CFG_PU_300K 0 > +#define ADP5585_Rx_PULL_CFG_PD_300K 1 > +#define ADP5585_Rx_PULL_CFG_PU_100K 2 > +#define ADP5585_Rx_PULL_CFG_DISABLE 3 > +#define ADP5585_Rx_PULL_CFG_MASK 3 Still supplying MASK is strange, why not supplying DISABLE? ... > +#define ADP5585_OSC_EN BIT(7) > +#define ADP5585_OSC_FREQ_50KHZ (0U << 5) > +#define ADP5585_OSC_FREQ_100KHZ (1U << 5) > +#define ADP5585_OSC_FREQ_200KHZ (2U << 5) > +#define ADP5585_OSC_FREQ_500KHZ (3U << 5) > +#define ADP5585_OSC_FREQ_MASK (3U << 5) GENMASK() ? And possible the similar question as per above.
On Sat, Jun 08, 2024 at 05:16:31PM +0300, Laurent Pinchart wrote: > From: Haibo Chen <haibo.chen@nxp.com> > > The ADP5585 is a 10/11 input/output port expander with a built in keypad > matrix decoder, programmable logic, reset generator, and PWM generator. > This driver supports the chip by modelling it as an MFD device, with two > child devices for the GPIO and PWM functions. > > The driver is derived from an initial implementation from NXP, available > in commit 8059835bee19 ("MLK-25917-1 mfd: adp5585: add ADI adp5585 core > support") in their BSP kernel tree. It has been extensively rewritten. > > Signed-off-by: Haibo Chen <haibo.chen@nxp.com> > Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Laurent: Just saw you already sent out adp5585 patches. Do you plan to continue work on this? If you are busy, I can help follow up this. Frank > --- > Changes since v2: > > - Add missing and remove extraneous headers > - Use i2c_get_match_data() > - Drop unneeded parentheses > - Use GENMASK() > - Drop of_match_ptr() > - Allow compilation on !OF with COMPILE_TEST > - Replace ADP5585_MAN_ID() macro with ADP5585_MAN_ID_MASK > - Drop unneeded macro > > Changes since v1: > > - Add comment to explain BANK and BIT macros > - Drop compatible strings from cells > - White space fixes > - Fix comparison to NULL > > Changes compared to the NXP original version: > > - Add MAINTAINERS entry > - Fix compatible strings for child devices > - Fix header guards > - Use lowercase hex constants > - White space fixes > - Use module_i2c_driver() > - Switch to regmap > - Drop I2C device ID table > - Drop ADP5585_REG_MASK > - Support R5 GPIO pin > - Drop dev field from adp5585_dev structure > - Check device ID at probe time > - Fix register field names > - Update copyright > - Update license to GPL-2.0-only > - Implement suspend/resume > --- > MAINTAINERS | 2 + > drivers/mfd/Kconfig | 12 +++ > drivers/mfd/Makefile | 1 + > drivers/mfd/adp5585.c | 199 ++++++++++++++++++++++++++++++++++++ > include/linux/mfd/adp5585.h | 126 +++++++++++++++++++++++ > 5 files changed, 340 insertions(+) > create mode 100644 drivers/mfd/adp5585.c > create mode 100644 include/linux/mfd/adp5585.h > > diff --git a/MAINTAINERS b/MAINTAINERS > index 8ebdde3106d3..1250992f7788 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -532,6 +532,8 @@ L: linux-gpio@vger.kernel.org > L: linux-pwm@vger.kernel.org > S: Maintained > F: Documentation/devicetree/bindings/*/adi,adp5585*.yaml > +F: drivers/mfd/adp5585.c > +F: include/linux/mfd/adp5585.h > > ADP5588 QWERTY KEYPAD AND IO EXPANDER DRIVER (ADP5588/ADP5587) > M: Michael Hennerich <michael.hennerich@analog.com> > diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig > index 266b4f54af60..05e8e1f0b602 100644 > --- a/drivers/mfd/Kconfig > +++ b/drivers/mfd/Kconfig > @@ -20,6 +20,18 @@ config MFD_CS5535 > This is the core driver for CS5535/CS5536 MFD functions. This is > necessary for using the board's GPIO and MFGPT functionality. > > +config MFD_ADP5585 > + tristate "Analog Devices ADP5585 MFD driver" > + select MFD_CORE > + select REGMAP_I2C > + depends on I2C > + depends on OF || COMPILE_TEST > + help > + Say yes here to add support for the Analog Devices ADP5585 GPIO > + expander, PWM and keypad controller. This includes the I2C driver and > + the core APIs _only_, you have to select individual components like > + the GPIO and PWM functions under the corresponding menus. > + > config MFD_ALTERA_A10SR > bool "Altera Arria10 DevKit System Resource chip" > depends on ARCH_INTEL_SOCFPGA && SPI_MASTER=y && OF > diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile > index c66f07edcd0e..37f36a019a68 100644 > --- a/drivers/mfd/Makefile > +++ b/drivers/mfd/Makefile > @@ -188,6 +188,7 @@ obj-$(CONFIG_MFD_DB8500_PRCMU) += db8500-prcmu.o > obj-$(CONFIG_AB8500_CORE) += ab8500-core.o ab8500-sysctrl.o > obj-$(CONFIG_MFD_TIMBERDALE) += timberdale.o > obj-$(CONFIG_PMIC_ADP5520) += adp5520.o > +obj-$(CONFIG_MFD_ADP5585) += adp5585.o > obj-$(CONFIG_MFD_KEMPLD) += kempld-core.o > obj-$(CONFIG_MFD_INTEL_QUARK_I2C_GPIO) += intel_quark_i2c_gpio.o > obj-$(CONFIG_LPC_SCH) += lpc_sch.o > diff --git a/drivers/mfd/adp5585.c b/drivers/mfd/adp5585.c > new file mode 100644 > index 000000000000..5268229eed18 > --- /dev/null > +++ b/drivers/mfd/adp5585.c > @@ -0,0 +1,199 @@ > +// SPDX-License-Identifier: GPL-2.0-only > +/* > + * Analog Devices ADP5585 I/O expander, PWM controller and keypad controller > + * > + * Copyright 2022 NXP > + * Copyright 2024 Ideas on Board Oy > + */ > + > +#include <linux/array_size.h> > +#include <linux/device.h> > +#include <linux/i2c.h> > +#include <linux/mfd/adp5585.h> > +#include <linux/mfd/core.h> > +#include <linux/mod_devicetable.h> > +#include <linux/module.h> > +#include <linux/regmap.h> > +#include <linux/types.h> > + > +static const struct mfd_cell adp5585_devs[] = { > + { .name = "adp5585-gpio", }, > + { .name = "adp5585-pwm", }, > +}; > + > +static const struct regmap_range adp5585_volatile_ranges[] = { > + regmap_reg_range(ADP5585_ID, ADP5585_GPI_STATUS_B), > +}; > + > +static const struct regmap_access_table adp5585_volatile_regs = { > + .yes_ranges = adp5585_volatile_ranges, > + .n_yes_ranges = ARRAY_SIZE(adp5585_volatile_ranges), > +}; > + > +static const u8 adp5585_regmap_defaults_00[ADP5585_MAX_REG + 1] = { > + /* 0x00 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x08 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x10 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x18 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x20 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x28 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x30 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x38 */ 0x00, 0x00, 0x00, 0x00, 0x00, > +}; > + > +static const u8 adp5585_regmap_defaults_02[ADP5585_MAX_REG + 1] = { > + /* 0x00 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x08 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x10 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xc3, > + /* 0x18 */ 0x03, 0x00, 0x03, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x20 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x28 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x30 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x38 */ 0x00, 0x00, 0x00, 0x00, 0x00, > +}; > + > +static const u8 adp5585_regmap_defaults_04[ADP5585_MAX_REG + 1] = { > + /* 0x00 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x08 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x10 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x55, > + /* 0x18 */ 0x05, 0x55, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x20 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x28 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x30 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, > + /* 0x38 */ 0x00, 0x00, 0x00, 0x00, 0x00, > +}; > + > +enum adp5585_regmap_type { > + ADP5585_REGMAP_00, > + ADP5585_REGMAP_02, > + ADP5585_REGMAP_04, > +}; > + > +static const struct regmap_config adp5585_regmap_configs[] = { > + [ADP5585_REGMAP_00] = { > + .reg_bits = 8, > + .val_bits = 8, > + .max_register = ADP5585_MAX_REG, > + .volatile_table = &adp5585_volatile_regs, > + .cache_type = REGCACHE_MAPLE, > + .reg_defaults_raw = adp5585_regmap_defaults_00, > + .num_reg_defaults_raw = sizeof(adp5585_regmap_defaults_00), > + }, > + [ADP5585_REGMAP_02] = { > + .reg_bits = 8, > + .val_bits = 8, > + .max_register = ADP5585_MAX_REG, > + .volatile_table = &adp5585_volatile_regs, > + .cache_type = REGCACHE_MAPLE, > + .reg_defaults_raw = adp5585_regmap_defaults_02, > + .num_reg_defaults_raw = sizeof(adp5585_regmap_defaults_02), > + }, > + [ADP5585_REGMAP_04] = { > + .reg_bits = 8, > + .val_bits = 8, > + .max_register = ADP5585_MAX_REG, > + .volatile_table = &adp5585_volatile_regs, > + .cache_type = REGCACHE_MAPLE, > + .reg_defaults_raw = adp5585_regmap_defaults_04, > + .num_reg_defaults_raw = sizeof(adp5585_regmap_defaults_04), > + }, > +}; > + > +static int adp5585_i2c_probe(struct i2c_client *i2c) > +{ > + const struct regmap_config *regmap_config; > + struct adp5585_dev *adp5585; > + unsigned int id; > + int ret; > + > + adp5585 = devm_kzalloc(&i2c->dev, sizeof(struct adp5585_dev), > + GFP_KERNEL); > + if (!adp5585) > + return -ENOMEM; > + > + i2c_set_clientdata(i2c, adp5585); > + > + regmap_config = i2c_get_match_data(i2c); > + adp5585->regmap = devm_regmap_init_i2c(i2c, regmap_config); > + if (IS_ERR(adp5585->regmap)) > + return dev_err_probe(&i2c->dev, PTR_ERR(adp5585->regmap), > + "Failed to initialize register map\n"); > + > + /* Verify the device ID. */ > + ret = regmap_read(adp5585->regmap, ADP5585_ID, &id); > + if (ret) > + return dev_err_probe(&i2c->dev, ret, > + "Failed to read device ID\n"); > + > + if ((id & ADP5585_MAN_ID_MASK) != ADP5585_MAN_ID_VALUE) > + return dev_err_probe(&i2c->dev, -ENODEV, > + "Invalid device ID 0x%02x\n", id); > + > + dev_dbg(&i2c->dev, "device ID 0x%02x\n", id); > + > + /* Add MFD devices. */ > + ret = devm_mfd_add_devices(&i2c->dev, PLATFORM_DEVID_AUTO, > + adp5585_devs, ARRAY_SIZE(adp5585_devs), > + NULL, 0, NULL); > + if (ret) > + return dev_err_probe(&i2c->dev, ret, > + "Failed to add MFD devices\n"); > + > + return 0; > +} > + > +static int adp5585_suspend(struct device *dev) > +{ > + struct adp5585_dev *adp5585 = dev_get_drvdata(dev); > + > + regcache_cache_only(adp5585->regmap, true); > + > + return 0; > +} > + > +static int adp5585_resume(struct device *dev) > +{ > + struct adp5585_dev *adp5585 = dev_get_drvdata(dev); > + > + regcache_cache_only(adp5585->regmap, false); > + regcache_mark_dirty(adp5585->regmap); > + > + return regcache_sync(adp5585->regmap); > +} > + > +static DEFINE_SIMPLE_DEV_PM_OPS(adp5585_pm, adp5585_suspend, adp5585_resume); > + > +static const struct of_device_id adp5585_of_match[] = { > + { > + .compatible = "adi,adp5585-00", > + .data = &adp5585_regmap_configs[ADP5585_REGMAP_00], > + }, { > + .compatible = "adi,adp5585-01", > + .data = &adp5585_regmap_configs[ADP5585_REGMAP_00], > + }, { > + .compatible = "adi,adp5585-02", > + .data = &adp5585_regmap_configs[ADP5585_REGMAP_02], > + }, { > + .compatible = "adi,adp5585-03", > + .data = &adp5585_regmap_configs[ADP5585_REGMAP_00], > + }, { > + .compatible = "adi,adp5585-04", > + .data = &adp5585_regmap_configs[ADP5585_REGMAP_04], > + }, > + { /* sentinel */ } > +}; > +MODULE_DEVICE_TABLE(of, adp5585_of_match); > + > +static struct i2c_driver adp5585_i2c_driver = { > + .driver = { > + .name = "adp5585", > + .of_match_table = adp5585_of_match, > + .pm = pm_sleep_ptr(&adp5585_pm), > + }, > + .probe = adp5585_i2c_probe, > +}; > +module_i2c_driver(adp5585_i2c_driver); > + > +MODULE_DESCRIPTION("ADP5585 core driver"); > +MODULE_AUTHOR("Haibo Chen <haibo.chen@nxp.com>"); > +MODULE_LICENSE("GPL"); > diff --git a/include/linux/mfd/adp5585.h b/include/linux/mfd/adp5585.h > new file mode 100644 > index 000000000000..92d90218762e > --- /dev/null > +++ b/include/linux/mfd/adp5585.h > @@ -0,0 +1,126 @@ > +/* SPDX-License-Identifier: GPL-2.0-only */ > +/* > + * Analog Devices ADP5585 I/O expander, PWM controller and keypad controller > + * > + * Copyright 2022 NXP > + * Copyright 2024 Ideas on Board Oy > + */ > + > +#ifndef __LINUX_MFD_ADP5585_H_ > +#define __LINUX_MFD_ADP5585_H_ > + > +#include <linux/bits.h> > + > +#define ADP5585_ID 0x00 > +#define ADP5585_MAN_ID_VALUE 0x20 > +#define ADP5585_MAN_ID_MASK GENMASK(7, 4) > +#define ADP5585_INT_STATUS 0x01 > +#define ADP5585_STATUS 0x02 > +#define ADP5585_FIFO_1 0x03 > +#define ADP5585_FIFO_2 0x04 > +#define ADP5585_FIFO_3 0x05 > +#define ADP5585_FIFO_4 0x06 > +#define ADP5585_FIFO_5 0x07 > +#define ADP5585_FIFO_6 0x08 > +#define ADP5585_FIFO_7 0x09 > +#define ADP5585_FIFO_8 0x0a > +#define ADP5585_FIFO_9 0x0b > +#define ADP5585_FIFO_10 0x0c > +#define ADP5585_FIFO_11 0x0d > +#define ADP5585_FIFO_12 0x0e > +#define ADP5585_FIFO_13 0x0f > +#define ADP5585_FIFO_14 0x10 > +#define ADP5585_FIFO_15 0x11 > +#define ADP5585_FIFO_16 0x12 > +#define ADP5585_GPI_INT_STAT_A 0x13 > +#define ADP5585_GPI_INT_STAT_B 0x14 > +#define ADP5585_GPI_STATUS_A 0x15 > +#define ADP5585_GPI_STATUS_B 0x16 > +#define ADP5585_RPULL_CONFIG_A 0x17 > +#define ADP5585_RPULL_CONFIG_B 0x18 > +#define ADP5585_RPULL_CONFIG_C 0x19 > +#define ADP5585_RPULL_CONFIG_D 0x1a > +#define ADP5585_Rx_PULL_CFG_PU_300K 0 > +#define ADP5585_Rx_PULL_CFG_PD_300K 1 > +#define ADP5585_Rx_PULL_CFG_PU_100K 2 > +#define ADP5585_Rx_PULL_CFG_DISABLE 3 > +#define ADP5585_Rx_PULL_CFG_MASK 3 > +#define ADP5585_GPI_INT_LEVEL_A 0x1b > +#define ADP5585_GPI_INT_LEVEL_B 0x1c > +#define ADP5585_GPI_EVENT_EN_A 0x1d > +#define ADP5585_GPI_EVENT_EN_B 0x1e > +#define ADP5585_GPI_INTERRUPT_EN_A 0x1f > +#define ADP5585_GPI_INTERRUPT_EN_B 0x20 > +#define ADP5585_DEBOUNCE_DIS_A 0x21 > +#define ADP5585_DEBOUNCE_DIS_B 0x22 > +#define ADP5585_GPO_DATA_OUT_A 0x23 > +#define ADP5585_GPO_DATA_OUT_B 0x24 > +#define ADP5585_GPO_OUT_MODE_A 0x25 > +#define ADP5585_GPO_OUT_MODE_B 0x26 > +#define ADP5585_GPIO_DIRECTION_A 0x27 > +#define ADP5585_GPIO_DIRECTION_B 0x28 > +#define ADP5585_RESET1_EVENT_A 0x29 > +#define ADP5585_RESET1_EVENT_B 0x2a > +#define ADP5585_RESET1_EVENT_C 0x2b > +#define ADP5585_RESET2_EVENT_A 0x2c > +#define ADP5585_RESET2_EVENT_B 0x2d > +#define ADP5585_RESET_CFG 0x2e > +#define ADP5585_PWM_OFFT_LOW 0x2f > +#define ADP5585_PWM_OFFT_HIGH 0x30 > +#define ADP5585_PWM_ONT_LOW 0x31 > +#define ADP5585_PWM_ONT_HIGH 0x32 > +#define ADP5585_PWM_CFG 0x33 > +#define ADP5585_PWM_IN_AND BIT(2) > +#define ADP5585_PWM_MODE BIT(1) > +#define ADP5585_PWM_EN BIT(0) > +#define ADP5585_LOGIC_CFG 0x34 > +#define ADP5585_LOGIC_FF_CFG 0x35 > +#define ADP5585_LOGIC_INT_EVENT_EN 0x36 > +#define ADP5585_POLL_PTIME_CFG 0x37 > +#define ADP5585_PIN_CONFIG_A 0x38 > +#define ADP5585_PIN_CONFIG_B 0x39 > +#define ADP5585_PIN_CONFIG_C 0x3a > +#define ADP5585_PULL_SELECT BIT(7) > +#define ADP5585_C4_EXTEND_CFG_GPIO11 (0U << 6) > +#define ADP5585_C4_EXTEND_CFG_RESET2 (1U << 6) > +#define ADP5585_C4_EXTEND_CFG_MASK GENMASK(6, 6) > +#define ADP5585_R4_EXTEND_CFG_GPIO5 (0U << 5) > +#define ADP5585_R4_EXTEND_CFG_RESET1 (1U << 5) > +#define ADP5585_R4_EXTEND_CFG_MASK GENMASK(5, 5) > +#define ADP5585_R3_EXTEND_CFG_GPIO4 (0U << 2) > +#define ADP5585_R3_EXTEND_CFG_LC (1U << 2) > +#define ADP5585_R3_EXTEND_CFG_PWM_OUT (2U << 2) > +#define ADP5585_R3_EXTEND_CFG_MASK GENMASK(3, 2) > +#define ADP5585_R0_EXTEND_CFG_GPIO1 (0U << 0) > +#define ADP5585_R0_EXTEND_CFG_LY (1U << 0) > +#define ADP5585_R0_EXTEND_CFG_MASK GENMASK(0, 0) > +#define ADP5585_GENERAL_CFG 0x3b > +#define ADP5585_OSC_EN BIT(7) > +#define ADP5585_OSC_FREQ_50KHZ (0U << 5) > +#define ADP5585_OSC_FREQ_100KHZ (1U << 5) > +#define ADP5585_OSC_FREQ_200KHZ (2U << 5) > +#define ADP5585_OSC_FREQ_500KHZ (3U << 5) > +#define ADP5585_OSC_FREQ_MASK (3U << 5) > +#define ADP5585_INT_CFG BIT(1) > +#define ADP5585_RST_CFG BIT(0) > +#define ADP5585_INT_EN 0x3c > + > +#define ADP5585_MAX_REG ADP5585_INT_EN > + > +/* > + * Bank 0 covers pins "GPIO 1/R0" to "GPIO 6/R5", numbered 0 to 5 by the > + * driver, and bank 1 covers pins "GPIO 7/C0" to "GPIO 11/C4", numbered 6 to > + * 10. Some variants of the ADP5585 don't support "GPIO 6/R5". As the driver > + * uses identical GPIO numbering for all variants to avoid confusion, GPIO 5 is > + * marked as reserved in the device tree for variants that don't support it. > + */ > +#define ADP5585_BANK(n) ((n) >= 6 ? 1 : 0) > +#define ADP5585_BIT(n) ((n) >= 6 ? BIT((n) - 6) : BIT(n)) > + > +struct regmap; > + > +struct adp5585_dev { > + struct regmap *regmap; > +}; > + > +#endif > -- > Regards, > > Laurent Pinchart >
Hi Frank, On Tue, Jul 16, 2024 at 10:39:27PM -0400, Frank Li wrote: > On Sat, Jun 08, 2024 at 05:16:31PM +0300, Laurent Pinchart wrote: > > From: Haibo Chen <haibo.chen@nxp.com> > > > > The ADP5585 is a 10/11 input/output port expander with a built in keypad > > matrix decoder, programmable logic, reset generator, and PWM generator. > > This driver supports the chip by modelling it as an MFD device, with two > > child devices for the GPIO and PWM functions. > > > > The driver is derived from an initial implementation from NXP, available > > in commit 8059835bee19 ("MLK-25917-1 mfd: adp5585: add ADI adp5585 core > > support") in their BSP kernel tree. It has been extensively rewritten. > > > > Signed-off-by: Haibo Chen <haibo.chen@nxp.com> > > Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> > > Laurent: > Just saw you already sent out adp5585 patches. Do you plan to > continue work on this? If you are busy, I can help follow up this. I just came back from vacation and have a large backlog. Please feel free to take my v4, rebase it, address any review comments, and send a v5 if you would like to help merging the driver faster. Please CC me on the patch submission. > > --- > > Changes since v2: > > > > - Add missing and remove extraneous headers > > - Use i2c_get_match_data() > > - Drop unneeded parentheses > > - Use GENMASK() > > - Drop of_match_ptr() > > - Allow compilation on !OF with COMPILE_TEST > > - Replace ADP5585_MAN_ID() macro with ADP5585_MAN_ID_MASK > > - Drop unneeded macro > > > > Changes since v1: > > > > - Add comment to explain BANK and BIT macros > > - Drop compatible strings from cells > > - White space fixes > > - Fix comparison to NULL > > > > Changes compared to the NXP original version: > > > > - Add MAINTAINERS entry > > - Fix compatible strings for child devices > > - Fix header guards > > - Use lowercase hex constants > > - White space fixes > > - Use module_i2c_driver() > > - Switch to regmap > > - Drop I2C device ID table > > - Drop ADP5585_REG_MASK > > - Support R5 GPIO pin > > - Drop dev field from adp5585_dev structure > > - Check device ID at probe time > > - Fix register field names > > - Update copyright > > - Update license to GPL-2.0-only > > - Implement suspend/resume > > --- > > MAINTAINERS | 2 + > > drivers/mfd/Kconfig | 12 +++ > > drivers/mfd/Makefile | 1 + > > drivers/mfd/adp5585.c | 199 ++++++++++++++++++++++++++++++++++++ > > include/linux/mfd/adp5585.h | 126 +++++++++++++++++++++++ > > 5 files changed, 340 insertions(+) > > create mode 100644 drivers/mfd/adp5585.c > > create mode 100644 include/linux/mfd/adp5585.h [snip]
diff --git a/MAINTAINERS b/MAINTAINERS index 8ebdde3106d3..1250992f7788 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -532,6 +532,8 @@ L: linux-gpio@vger.kernel.org L: linux-pwm@vger.kernel.org S: Maintained F: Documentation/devicetree/bindings/*/adi,adp5585*.yaml +F: drivers/mfd/adp5585.c +F: include/linux/mfd/adp5585.h ADP5588 QWERTY KEYPAD AND IO EXPANDER DRIVER (ADP5588/ADP5587) M: Michael Hennerich <michael.hennerich@analog.com> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index 266b4f54af60..05e8e1f0b602 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -20,6 +20,18 @@ config MFD_CS5535 This is the core driver for CS5535/CS5536 MFD functions. This is necessary for using the board's GPIO and MFGPT functionality. +config MFD_ADP5585 + tristate "Analog Devices ADP5585 MFD driver" + select MFD_CORE + select REGMAP_I2C + depends on I2C + depends on OF || COMPILE_TEST + help + Say yes here to add support for the Analog Devices ADP5585 GPIO + expander, PWM and keypad controller. This includes the I2C driver and + the core APIs _only_, you have to select individual components like + the GPIO and PWM functions under the corresponding menus. + config MFD_ALTERA_A10SR bool "Altera Arria10 DevKit System Resource chip" depends on ARCH_INTEL_SOCFPGA && SPI_MASTER=y && OF diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile index c66f07edcd0e..37f36a019a68 100644 --- a/drivers/mfd/Makefile +++ b/drivers/mfd/Makefile @@ -188,6 +188,7 @@ obj-$(CONFIG_MFD_DB8500_PRCMU) += db8500-prcmu.o obj-$(CONFIG_AB8500_CORE) += ab8500-core.o ab8500-sysctrl.o obj-$(CONFIG_MFD_TIMBERDALE) += timberdale.o obj-$(CONFIG_PMIC_ADP5520) += adp5520.o +obj-$(CONFIG_MFD_ADP5585) += adp5585.o obj-$(CONFIG_MFD_KEMPLD) += kempld-core.o obj-$(CONFIG_MFD_INTEL_QUARK_I2C_GPIO) += intel_quark_i2c_gpio.o obj-$(CONFIG_LPC_SCH) += lpc_sch.o diff --git a/drivers/mfd/adp5585.c b/drivers/mfd/adp5585.c new file mode 100644 index 000000000000..5268229eed18 --- /dev/null +++ b/drivers/mfd/adp5585.c @@ -0,0 +1,199 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Analog Devices ADP5585 I/O expander, PWM controller and keypad controller + * + * Copyright 2022 NXP + * Copyright 2024 Ideas on Board Oy + */ + +#include <linux/array_size.h> +#include <linux/device.h> +#include <linux/i2c.h> +#include <linux/mfd/adp5585.h> +#include <linux/mfd/core.h> +#include <linux/mod_devicetable.h> +#include <linux/module.h> +#include <linux/regmap.h> +#include <linux/types.h> + +static const struct mfd_cell adp5585_devs[] = { + { .name = "adp5585-gpio", }, + { .name = "adp5585-pwm", }, +}; + +static const struct regmap_range adp5585_volatile_ranges[] = { + regmap_reg_range(ADP5585_ID, ADP5585_GPI_STATUS_B), +}; + +static const struct regmap_access_table adp5585_volatile_regs = { + .yes_ranges = adp5585_volatile_ranges, + .n_yes_ranges = ARRAY_SIZE(adp5585_volatile_ranges), +}; + +static const u8 adp5585_regmap_defaults_00[ADP5585_MAX_REG + 1] = { + /* 0x00 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x08 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x10 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x18 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x20 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x28 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x30 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x38 */ 0x00, 0x00, 0x00, 0x00, 0x00, +}; + +static const u8 adp5585_regmap_defaults_02[ADP5585_MAX_REG + 1] = { + /* 0x00 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x08 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x10 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0xc3, + /* 0x18 */ 0x03, 0x00, 0x03, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x20 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x28 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x30 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x38 */ 0x00, 0x00, 0x00, 0x00, 0x00, +}; + +static const u8 adp5585_regmap_defaults_04[ADP5585_MAX_REG + 1] = { + /* 0x00 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x08 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x10 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x55, + /* 0x18 */ 0x05, 0x55, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x20 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x28 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x30 */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, + /* 0x38 */ 0x00, 0x00, 0x00, 0x00, 0x00, +}; + +enum adp5585_regmap_type { + ADP5585_REGMAP_00, + ADP5585_REGMAP_02, + ADP5585_REGMAP_04, +}; + +static const struct regmap_config adp5585_regmap_configs[] = { + [ADP5585_REGMAP_00] = { + .reg_bits = 8, + .val_bits = 8, + .max_register = ADP5585_MAX_REG, + .volatile_table = &adp5585_volatile_regs, + .cache_type = REGCACHE_MAPLE, + .reg_defaults_raw = adp5585_regmap_defaults_00, + .num_reg_defaults_raw = sizeof(adp5585_regmap_defaults_00), + }, + [ADP5585_REGMAP_02] = { + .reg_bits = 8, + .val_bits = 8, + .max_register = ADP5585_MAX_REG, + .volatile_table = &adp5585_volatile_regs, + .cache_type = REGCACHE_MAPLE, + .reg_defaults_raw = adp5585_regmap_defaults_02, + .num_reg_defaults_raw = sizeof(adp5585_regmap_defaults_02), + }, + [ADP5585_REGMAP_04] = { + .reg_bits = 8, + .val_bits = 8, + .max_register = ADP5585_MAX_REG, + .volatile_table = &adp5585_volatile_regs, + .cache_type = REGCACHE_MAPLE, + .reg_defaults_raw = adp5585_regmap_defaults_04, + .num_reg_defaults_raw = sizeof(adp5585_regmap_defaults_04), + }, +}; + +static int adp5585_i2c_probe(struct i2c_client *i2c) +{ + const struct regmap_config *regmap_config; + struct adp5585_dev *adp5585; + unsigned int id; + int ret; + + adp5585 = devm_kzalloc(&i2c->dev, sizeof(struct adp5585_dev), + GFP_KERNEL); + if (!adp5585) + return -ENOMEM; + + i2c_set_clientdata(i2c, adp5585); + + regmap_config = i2c_get_match_data(i2c); + adp5585->regmap = devm_regmap_init_i2c(i2c, regmap_config); + if (IS_ERR(adp5585->regmap)) + return dev_err_probe(&i2c->dev, PTR_ERR(adp5585->regmap), + "Failed to initialize register map\n"); + + /* Verify the device ID. */ + ret = regmap_read(adp5585->regmap, ADP5585_ID, &id); + if (ret) + return dev_err_probe(&i2c->dev, ret, + "Failed to read device ID\n"); + + if ((id & ADP5585_MAN_ID_MASK) != ADP5585_MAN_ID_VALUE) + return dev_err_probe(&i2c->dev, -ENODEV, + "Invalid device ID 0x%02x\n", id); + + dev_dbg(&i2c->dev, "device ID 0x%02x\n", id); + + /* Add MFD devices. */ + ret = devm_mfd_add_devices(&i2c->dev, PLATFORM_DEVID_AUTO, + adp5585_devs, ARRAY_SIZE(adp5585_devs), + NULL, 0, NULL); + if (ret) + return dev_err_probe(&i2c->dev, ret, + "Failed to add MFD devices\n"); + + return 0; +} + +static int adp5585_suspend(struct device *dev) +{ + struct adp5585_dev *adp5585 = dev_get_drvdata(dev); + + regcache_cache_only(adp5585->regmap, true); + + return 0; +} + +static int adp5585_resume(struct device *dev) +{ + struct adp5585_dev *adp5585 = dev_get_drvdata(dev); + + regcache_cache_only(adp5585->regmap, false); + regcache_mark_dirty(adp5585->regmap); + + return regcache_sync(adp5585->regmap); +} + +static DEFINE_SIMPLE_DEV_PM_OPS(adp5585_pm, adp5585_suspend, adp5585_resume); + +static const struct of_device_id adp5585_of_match[] = { + { + .compatible = "adi,adp5585-00", + .data = &adp5585_regmap_configs[ADP5585_REGMAP_00], + }, { + .compatible = "adi,adp5585-01", + .data = &adp5585_regmap_configs[ADP5585_REGMAP_00], + }, { + .compatible = "adi,adp5585-02", + .data = &adp5585_regmap_configs[ADP5585_REGMAP_02], + }, { + .compatible = "adi,adp5585-03", + .data = &adp5585_regmap_configs[ADP5585_REGMAP_00], + }, { + .compatible = "adi,adp5585-04", + .data = &adp5585_regmap_configs[ADP5585_REGMAP_04], + }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, adp5585_of_match); + +static struct i2c_driver adp5585_i2c_driver = { + .driver = { + .name = "adp5585", + .of_match_table = adp5585_of_match, + .pm = pm_sleep_ptr(&adp5585_pm), + }, + .probe = adp5585_i2c_probe, +}; +module_i2c_driver(adp5585_i2c_driver); + +MODULE_DESCRIPTION("ADP5585 core driver"); +MODULE_AUTHOR("Haibo Chen <haibo.chen@nxp.com>"); +MODULE_LICENSE("GPL"); diff --git a/include/linux/mfd/adp5585.h b/include/linux/mfd/adp5585.h new file mode 100644 index 000000000000..92d90218762e --- /dev/null +++ b/include/linux/mfd/adp5585.h @@ -0,0 +1,126 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * Analog Devices ADP5585 I/O expander, PWM controller and keypad controller + * + * Copyright 2022 NXP + * Copyright 2024 Ideas on Board Oy + */ + +#ifndef __LINUX_MFD_ADP5585_H_ +#define __LINUX_MFD_ADP5585_H_ + +#include <linux/bits.h> + +#define ADP5585_ID 0x00 +#define ADP5585_MAN_ID_VALUE 0x20 +#define ADP5585_MAN_ID_MASK GENMASK(7, 4) +#define ADP5585_INT_STATUS 0x01 +#define ADP5585_STATUS 0x02 +#define ADP5585_FIFO_1 0x03 +#define ADP5585_FIFO_2 0x04 +#define ADP5585_FIFO_3 0x05 +#define ADP5585_FIFO_4 0x06 +#define ADP5585_FIFO_5 0x07 +#define ADP5585_FIFO_6 0x08 +#define ADP5585_FIFO_7 0x09 +#define ADP5585_FIFO_8 0x0a +#define ADP5585_FIFO_9 0x0b +#define ADP5585_FIFO_10 0x0c +#define ADP5585_FIFO_11 0x0d +#define ADP5585_FIFO_12 0x0e +#define ADP5585_FIFO_13 0x0f +#define ADP5585_FIFO_14 0x10 +#define ADP5585_FIFO_15 0x11 +#define ADP5585_FIFO_16 0x12 +#define ADP5585_GPI_INT_STAT_A 0x13 +#define ADP5585_GPI_INT_STAT_B 0x14 +#define ADP5585_GPI_STATUS_A 0x15 +#define ADP5585_GPI_STATUS_B 0x16 +#define ADP5585_RPULL_CONFIG_A 0x17 +#define ADP5585_RPULL_CONFIG_B 0x18 +#define ADP5585_RPULL_CONFIG_C 0x19 +#define ADP5585_RPULL_CONFIG_D 0x1a +#define ADP5585_Rx_PULL_CFG_PU_300K 0 +#define ADP5585_Rx_PULL_CFG_PD_300K 1 +#define ADP5585_Rx_PULL_CFG_PU_100K 2 +#define ADP5585_Rx_PULL_CFG_DISABLE 3 +#define ADP5585_Rx_PULL_CFG_MASK 3 +#define ADP5585_GPI_INT_LEVEL_A 0x1b +#define ADP5585_GPI_INT_LEVEL_B 0x1c +#define ADP5585_GPI_EVENT_EN_A 0x1d +#define ADP5585_GPI_EVENT_EN_B 0x1e +#define ADP5585_GPI_INTERRUPT_EN_A 0x1f +#define ADP5585_GPI_INTERRUPT_EN_B 0x20 +#define ADP5585_DEBOUNCE_DIS_A 0x21 +#define ADP5585_DEBOUNCE_DIS_B 0x22 +#define ADP5585_GPO_DATA_OUT_A 0x23 +#define ADP5585_GPO_DATA_OUT_B 0x24 +#define ADP5585_GPO_OUT_MODE_A 0x25 +#define ADP5585_GPO_OUT_MODE_B 0x26 +#define ADP5585_GPIO_DIRECTION_A 0x27 +#define ADP5585_GPIO_DIRECTION_B 0x28 +#define ADP5585_RESET1_EVENT_A 0x29 +#define ADP5585_RESET1_EVENT_B 0x2a +#define ADP5585_RESET1_EVENT_C 0x2b +#define ADP5585_RESET2_EVENT_A 0x2c +#define ADP5585_RESET2_EVENT_B 0x2d +#define ADP5585_RESET_CFG 0x2e +#define ADP5585_PWM_OFFT_LOW 0x2f +#define ADP5585_PWM_OFFT_HIGH 0x30 +#define ADP5585_PWM_ONT_LOW 0x31 +#define ADP5585_PWM_ONT_HIGH 0x32 +#define ADP5585_PWM_CFG 0x33 +#define ADP5585_PWM_IN_AND BIT(2) +#define ADP5585_PWM_MODE BIT(1) +#define ADP5585_PWM_EN BIT(0) +#define ADP5585_LOGIC_CFG 0x34 +#define ADP5585_LOGIC_FF_CFG 0x35 +#define ADP5585_LOGIC_INT_EVENT_EN 0x36 +#define ADP5585_POLL_PTIME_CFG 0x37 +#define ADP5585_PIN_CONFIG_A 0x38 +#define ADP5585_PIN_CONFIG_B 0x39 +#define ADP5585_PIN_CONFIG_C 0x3a +#define ADP5585_PULL_SELECT BIT(7) +#define ADP5585_C4_EXTEND_CFG_GPIO11 (0U << 6) +#define ADP5585_C4_EXTEND_CFG_RESET2 (1U << 6) +#define ADP5585_C4_EXTEND_CFG_MASK GENMASK(6, 6) +#define ADP5585_R4_EXTEND_CFG_GPIO5 (0U << 5) +#define ADP5585_R4_EXTEND_CFG_RESET1 (1U << 5) +#define ADP5585_R4_EXTEND_CFG_MASK GENMASK(5, 5) +#define ADP5585_R3_EXTEND_CFG_GPIO4 (0U << 2) +#define ADP5585_R3_EXTEND_CFG_LC (1U << 2) +#define ADP5585_R3_EXTEND_CFG_PWM_OUT (2U << 2) +#define ADP5585_R3_EXTEND_CFG_MASK GENMASK(3, 2) +#define ADP5585_R0_EXTEND_CFG_GPIO1 (0U << 0) +#define ADP5585_R0_EXTEND_CFG_LY (1U << 0) +#define ADP5585_R0_EXTEND_CFG_MASK GENMASK(0, 0) +#define ADP5585_GENERAL_CFG 0x3b +#define ADP5585_OSC_EN BIT(7) +#define ADP5585_OSC_FREQ_50KHZ (0U << 5) +#define ADP5585_OSC_FREQ_100KHZ (1U << 5) +#define ADP5585_OSC_FREQ_200KHZ (2U << 5) +#define ADP5585_OSC_FREQ_500KHZ (3U << 5) +#define ADP5585_OSC_FREQ_MASK (3U << 5) +#define ADP5585_INT_CFG BIT(1) +#define ADP5585_RST_CFG BIT(0) +#define ADP5585_INT_EN 0x3c + +#define ADP5585_MAX_REG ADP5585_INT_EN + +/* + * Bank 0 covers pins "GPIO 1/R0" to "GPIO 6/R5", numbered 0 to 5 by the + * driver, and bank 1 covers pins "GPIO 7/C0" to "GPIO 11/C4", numbered 6 to + * 10. Some variants of the ADP5585 don't support "GPIO 6/R5". As the driver + * uses identical GPIO numbering for all variants to avoid confusion, GPIO 5 is + * marked as reserved in the device tree for variants that don't support it. + */ +#define ADP5585_BANK(n) ((n) >= 6 ? 1 : 0) +#define ADP5585_BIT(n) ((n) >= 6 ? BIT((n) - 6) : BIT(n)) + +struct regmap; + +struct adp5585_dev { + struct regmap *regmap; +}; + +#endif