| Message ID | IA1PR20MB49530D9BC6C8011B730433C2BBDE2@IA1PR20MB4953.namprd20.prod.outlook.com |
|---|---|
| State | New |
| Headers | show |
| Series | riscv: sophgo: Add pinctrl support for CV1800 series SoC | expand |
Hi Inochi, thanks for your patch! Some comments below: On Thu, Jul 4, 2024 at 7:47 AM Inochi Amaoto <inochiama@outlook.com> wrote: > Add pinctrl support for Sophgo CV1800 series SoC. > > Signed-off-by: Inochi Amaoto <inochiama@outlook.com> (...) > + bias-pull-up: > + type: boolean description: Setting this true will result in how many Ohms of pull up and to what voltage? > + bias-pull-down: > + type: boolean How many Ohms by default? It's very helpful for designers writing the device tree to know this. > + drive-strength: > + $ref: /schemas/types.yaml#/definitions/uint32 > + minimum: 0 > + maximum: 7 0,1, ... 7 ... units of what? What does the values represent? 7 mA? I think not. This should be in mA and parsed to any custom values. If you need more resolution, consider using driver-strength-microamp and parse that value instead. > + input-schmitt: > + $ref: /schemas/types.yaml#/definitions/uint32 > + minimum: 0 > + maximum: 7 What is this custom property? We support input-schmitt-enable and input-schmitt-disable, if you want to add a new standard property input-schmitt, then send a separate patch to Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml and explain what the argument means, it should be in SI units. For a full custom property, use sophgo, prefixes. > + slew-rate: > + enum: [ 0, 1 ] What is slew rate 0 and 1? What does it represent? microvolts per second how much (I don't know, just guessing) > + sophgo,bus-holder: > + description: enable bus holder This description is a bit too little, we need to know what this thing is and what it is used for. If it is definied in some other DT binding then reference that file. Yours, Linus Walleij
On Fri, Jul 05, 2024 at 11:50:09AM GMT, Linus Walleij wrote: > Hi Inochi, > > thanks for your patch! > > Some comments below: > > On Thu, Jul 4, 2024 at 7:47 AM Inochi Amaoto <inochiama@outlook.com> wrote: > > > Add pinctrl support for Sophgo CV1800 series SoC. > > > > Signed-off-by: Inochi Amaoto <inochiama@outlook.com> > (...) > > + bias-pull-up: > > + type: boolean > > description: Setting this true will result in how many Ohms of pull up > and to what voltage? > > > + bias-pull-down: > > + type: boolean > > How many Ohms by default? It's very helpful for designers writing the > device tree to know this. > Pullup in 79k and pulldown is 87k. I will add these to the description. > > + drive-strength: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + minimum: 0 > > + maximum: 7 > > 0,1, ... 7 ... units of what? What does the values represent? > 7 mA? I think not. This should be in mA and parsed to any custom > values. > > If you need more resolution, consider using driver-strength-microamp and > parse that value instead. > This value depends on the type of the pin. Different pin have different typical drive strength. I will switch to the real value and check it in the driver. > > + input-schmitt: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + minimum: 0 > > + maximum: 7 > > What is this custom property? We support input-schmitt-enable > and input-schmitt-disable, if you want to add a new standard property > input-schmitt, then send a separate patch to > Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml > and explain what the argument means, it should be in SI units. > > For a full custom property, use sophgo, prefixes. > Thanks for the reminder. I have seen `input-schmitt` in the generic pinconf table. I will sumbit a new patch and add this to the pincfg-node. > > + slew-rate: > > + enum: [ 0, 1 ] > > What is slew rate 0 and 1? What does it represent? > > microvolts per second how much (I don't know, just guessing) > According to the document from sophgo, 0 is fast rate and 1 is slow. > > + sophgo,bus-holder: > > + description: enable bus holder > > This description is a bit too little, we need to know what this thing > is and what it is > used for. If it is definied in some other DT binding then reference that file. > > Yours, > Linus Walleij Thanks I will improve it. Regards, Inochi
On Thu, Jul 04, 2024 at 01:46:37PM +0800, Inochi Amaoto wrote: > Add pinctrl support for Sophgo CV1800 series SoC. > > Signed-off-by: Inochi Amaoto <inochiama@outlook.com> > --- > .../pinctrl/sophgo,cv1800-pinctrl.yaml | 120 +++++++++++++++++ > include/dt-bindings/pinctrl/pinctrl-cv1800b.h | 63 +++++++++ > include/dt-bindings/pinctrl/pinctrl-cv1812h.h | 127 ++++++++++++++++++ > include/dt-bindings/pinctrl/pinctrl-cv18xx.h | 19 +++ > include/dt-bindings/pinctrl/pinctrl-sg2000.h | 127 ++++++++++++++++++ > include/dt-bindings/pinctrl/pinctrl-sg2002.h | 79 +++++++++++ > 6 files changed, 535 insertions(+) > create mode 100644 Documentation/devicetree/bindings/pinctrl/sophgo,cv1800-pinctrl.yaml > create mode 100644 include/dt-bindings/pinctrl/pinctrl-cv1800b.h > create mode 100644 include/dt-bindings/pinctrl/pinctrl-cv1812h.h > create mode 100644 include/dt-bindings/pinctrl/pinctrl-cv18xx.h > create mode 100644 include/dt-bindings/pinctrl/pinctrl-sg2000.h > create mode 100644 include/dt-bindings/pinctrl/pinctrl-sg2002.h > > diff --git a/Documentation/devicetree/bindings/pinctrl/sophgo,cv1800-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/sophgo,cv1800-pinctrl.yaml > new file mode 100644 > index 000000000000..b7e4084b78d6 > --- /dev/null > +++ b/Documentation/devicetree/bindings/pinctrl/sophgo,cv1800-pinctrl.yaml > @@ -0,0 +1,120 @@ > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/pinctrl/sophgo,cv1800-pinctrl.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Sophgo CV1800 Pin Controller > + > +maintainers: > + - Inochi Amaoto <inochiama@outlook.com> > + > +properties: > + compatible: > + enum: > + - sophgo,cv1800b-pinctrl > + - sophgo,cv1812h-pinctrl > + - sophgo,sg2000-pinctrl > + - sophgo,sg2002-pinctrl > + > + reg: > + items: > + - description: pinctrl for system domain > + - description: pinctrl for rtc domain Based on the example's addresses, this isn't 1 block, but 2 blocks. Is this really 1 block, 2 instances of the same block, or 2 different blocks? > + > + reg-names: > + items: > + - const: sys > + - const: rtc > + > + resets: > + maxItems: 1 > + > +patternProperties: > + '-cfg$': > + type: object > + patternProperties: > + '-pins$': > + type: object > + description: | > + A pinctrl node should contain at least one subnode representing the It's the '-cfg' node that 'should contain at least one subnode', not this node. > + pinctrl groups available on the machine. Each subnode will list the > + pins it needs, and how they should be configured, with regard to > + muxer configuration, bias, input enable/disable, input schmitt > + trigger enable/disable, slew-rate and drive strength. > + $ref: /schemas/pinctrl/pincfg-node.yaml > + > + properties: > + pinmux: > + description: | > + The list of GPIOs and their mux settings that properties in the > + node apply to. This should be set using the GPIOMUX or GPIOMUX2 > + macro. > + $ref: /schemas/pinctrl/pinmux-node.yaml#/properties/pinmux > + > + bias-pull-up: > + type: boolean > + > + bias-pull-down: > + type: boolean > + > + drive-strength: > + $ref: /schemas/types.yaml#/definitions/uint32 > + minimum: 0 > + maximum: 7 > + > + input-schmitt: > + $ref: /schemas/types.yaml#/definitions/uint32 > + minimum: 0 > + maximum: 7 > + > + slew-rate: > + enum: [ 0, 1 ] > + > + sophgo,bus-holder: > + description: enable bus holder > + type: boolean > + > + additionalProperties: false > + > + additionalProperties: false In the indented cases, put these before properties or patternProperties. > + > +required: > + - compatible > + - reg > + - reg-names > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/pinctrl/pinctrl-cv1800b.h> > + > + soc { > + #address-cells = <1>; > + #size-cells = <1>; > + > + pinctrl@3001000 { > + compatible = "sophgo,cv1800b-pinctrl"; > + reg = <0x03001000 0x1000>, > + <0x05027000 0x1000>; > + reg-names = "sys", "rtc"; > + > + uart0_cfg: uart0-cfg { > + uart0-pins { > + pinmux = <PINMUX(PIN_UART0_TX, 0)>, > + <PINMUX(PIN_UART0_RX, 0)>; > + bias-pull-up; > + drive-strength = <2>; > + slew-rate = <0>; > + }; > + }; > + }; > + > + uart0 { > + pinctrl-0 = <&uart0_cfg>; > + pinctrl-names = "default"; Not a complete node. Plus the examples for a provider don't show the consumer side and vice-versa. So drop the node. > + }; > + }; > + > +... > diff --git a/include/dt-bindings/pinctrl/pinctrl-cv1800b.h b/include/dt-bindings/pinctrl/pinctrl-cv1800b.h > new file mode 100644 > index 000000000000..0593fc33d470 > --- /dev/null > +++ b/include/dt-bindings/pinctrl/pinctrl-cv1800b.h > @@ -0,0 +1,63 @@ > +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ > +/* > + * Copyright (C) 2024 Inochi Amaoto <inochiama@outlook.com> > + * > + * This file is generated from vendor pinout definition. > + */ > + > +#ifndef _DT_BINDINGS_PINCTRL_CV1800B_H > +#define _DT_BINDINGS_PINCTRL_CV1800B_H > + > +#include <dt-bindings/pinctrl/pinctrl-cv18xx.h> > + > +#define PIN_AUD_AOUTR 1 > +#define PIN_SD0_CLK 3 > +#define PIN_SD0_CMD 4 > +#define PIN_SD0_D0 5 > +#define PIN_SD0_D1 7 > +#define PIN_SD0_D2 8 > +#define PIN_SD0_D3 9 > +#define PIN_SD0_CD 11 > +#define PIN_SD0_PWR_EN 12 > +#define PIN_SPK_EN 14 > +#define PIN_UART0_TX 15 > +#define PIN_UART0_RX 16 > +#define PIN_SPINOR_HOLD_X 17 > +#define PIN_SPINOR_SCK 18 > +#define PIN_SPINOR_MOSI 19 > +#define PIN_SPINOR_WP_X 20 > +#define PIN_SPINOR_MISO 21 > +#define PIN_SPINOR_CS_X 22 > +#define PIN_IIC0_SCL 23 > +#define PIN_IIC0_SDA 24 > +#define PIN_AUX0 25 > +#define PIN_PWR_VBAT_DET 30 > +#define PIN_PWR_SEQ2 31 > +#define PIN_XTAL_XIN 33 > +#define PIN_SD1_GPIO0 35 > +#define PIN_SD1_GPIO1 36 > +#define PIN_SD1_D3 38 > +#define PIN_SD1_D2 39 > +#define PIN_SD1_D1 40 > +#define PIN_SD1_D0 41 > +#define PIN_SD1_CMD 42 > +#define PIN_SD1_CLK 43 > +#define PIN_ADC1 44 > +#define PIN_USB_VBUS_DET 45 > +#define PIN_ETH_TXP 47 > +#define PIN_ETH_TXM 48 > +#define PIN_ETH_RXP 49 > +#define PIN_ETH_RXM 50 > +#define PIN_MIPIRX4N 56 > +#define PIN_MIPIRX4P 57 > +#define PIN_MIPIRX3N 58 > +#define PIN_MIPIRX3P 59 > +#define PIN_MIPIRX2N 60 > +#define PIN_MIPIRX2P 61 > +#define PIN_MIPIRX1N 62 > +#define PIN_MIPIRX1P 63 > +#define PIN_MIPIRX0N 64 > +#define PIN_MIPIRX0P 65 > +#define PIN_AUD_AINL_MIC 67 > + > +#endif /* _DT_BINDINGS_PINCTRL_CV1800B_H */ > diff --git a/include/dt-bindings/pinctrl/pinctrl-cv1812h.h b/include/dt-bindings/pinctrl/pinctrl-cv1812h.h > new file mode 100644 > index 000000000000..2908de347919 > --- /dev/null > +++ b/include/dt-bindings/pinctrl/pinctrl-cv1812h.h > @@ -0,0 +1,127 @@ > +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ > +/* > + * Copyright (C) 2024 Inochi Amaoto <inochiama@outlook.com> > + * > + * This file is generated from vendor pinout definition. > + */ > + > +#ifndef _DT_BINDINGS_PINCTRL_CV1812H_H > +#define _DT_BINDINGS_PINCTRL_CV1812H_H > + > +#include <dt-bindings/pinctrl/pinctrl-cv18xx.h> > + > +#define PINPOS(row, col) \ > + ((((row) - 'A' + 1) << 8) + ((col) - 1)) > + > +#define PIN_MIPI_TXM4 PINPOS('A', 2) > +#define PIN_MIPIRX0N PINPOS('A', 4) > +#define PIN_MIPIRX3P PINPOS('A', 6) > +#define PIN_MIPIRX4P PINPOS('A', 7) > +#define PIN_VIVO_D2 PINPOS('A', 9) > +#define PIN_VIVO_D3 PINPOS('A', 10) > +#define PIN_VIVO_D10 PINPOS('A', 12) > +#define PIN_USB_VBUS_DET PINPOS('A', 13) > +#define PIN_MIPI_TXP3 PINPOS('B', 1) > +#define PIN_MIPI_TXM3 PINPOS('B', 2) > +#define PIN_MIPI_TXP4 PINPOS('B', 3) > +#define PIN_MIPIRX0P PINPOS('B', 4) > +#define PIN_MIPIRX1N PINPOS('B', 5) > +#define PIN_MIPIRX2N PINPOS('B', 6) > +#define PIN_MIPIRX4N PINPOS('B', 7) > +#define PIN_MIPIRX5N PINPOS('B', 8) > +#define PIN_VIVO_D1 PINPOS('B', 9) > +#define PIN_VIVO_D5 PINPOS('B', 10) > +#define PIN_VIVO_D7 PINPOS('B', 11) > +#define PIN_VIVO_D9 PINPOS('B', 12) > +#define PIN_USB_ID PINPOS('B', 13) > +#define PIN_ETH_RXM PINPOS('B', 15) > +#define PIN_MIPI_TXP2 PINPOS('C', 1) > +#define PIN_MIPI_TXM2 PINPOS('C', 2) > +#define PIN_CAM_PD0 PINPOS('C', 3) > +#define PIN_CAM_MCLK0 PINPOS('C', 4) > +#define PIN_MIPIRX1P PINPOS('C', 5) > +#define PIN_MIPIRX2P PINPOS('C', 6) > +#define PIN_MIPIRX3N PINPOS('C', 7) > +#define PIN_MIPIRX5P PINPOS('C', 8) > +#define PIN_VIVO_CLK PINPOS('C', 9) > +#define PIN_VIVO_D6 PINPOS('C', 10) > +#define PIN_VIVO_D8 PINPOS('C', 11) > +#define PIN_USB_VBUS_EN PINPOS('C', 12) > +#define PIN_ETH_RXP PINPOS('C', 14) > +#define PIN_GPIO_RTX PINPOS('C', 15) > +#define PIN_MIPI_TXP1 PINPOS('D', 1) > +#define PIN_MIPI_TXM1 PINPOS('D', 2) > +#define PIN_CAM_MCLK1 PINPOS('D', 3) > +#define PIN_IIC3_SCL PINPOS('D', 4) > +#define PIN_VIVO_D4 PINPOS('D', 10) > +#define PIN_ETH_TXM PINPOS('D', 14) > +#define PIN_ETH_TXP PINPOS('D', 15) > +#define PIN_MIPI_TXP0 PINPOS('E', 1) > +#define PIN_MIPI_TXM0 PINPOS('E', 2) > +#define PIN_CAM_PD1 PINPOS('E', 4) > +#define PIN_CAM_RST0 PINPOS('E', 5) > +#define PIN_VIVO_D0 PINPOS('E', 10) > +#define PIN_ADC1 PINPOS('E', 13) > +#define PIN_ADC2 PINPOS('E', 14) > +#define PIN_ADC3 PINPOS('E', 15) > +#define PIN_AUD_AOUTL PINPOS('F', 2) > +#define PIN_IIC3_SDA PINPOS('F', 4) > +#define PIN_SD1_D2 PINPOS('F', 14) > +#define PIN_AUD_AOUTR PINPOS('G', 2) > +#define PIN_SD1_D3 PINPOS('G', 13) > +#define PIN_SD1_CLK PINPOS('G', 14) > +#define PIN_SD1_CMD PINPOS('G', 15) > +#define PIN_AUD_AINL_MIC PINPOS('H', 1) > +#define PIN_RSTN PINPOS('H', 12) > +#define PIN_PWM0_BUCK PINPOS('H', 13) > +#define PIN_SD1_D1 PINPOS('H', 14) > +#define PIN_SD1_D0 PINPOS('H', 15) > +#define PIN_AUD_AINR_MIC PINPOS('J', 1) > +#define PIN_IIC2_SCL PINPOS('J', 13) > +#define PIN_IIC2_SDA PINPOS('J', 14) > +#define PIN_SD0_CD PINPOS('K', 2) > +#define PIN_SD0_D1 PINPOS('K', 3) > +#define PIN_UART2_RX PINPOS('K', 13) > +#define PIN_UART2_CTS PINPOS('K', 14) > +#define PIN_UART2_TX PINPOS('K', 15) > +#define PIN_SD0_CLK PINPOS('L', 1) > +#define PIN_SD0_D0 PINPOS('L', 2) > +#define PIN_SD0_CMD PINPOS('L', 3) > +#define PIN_CLK32K PINPOS('L', 14) > +#define PIN_UART2_RTS PINPOS('L', 15) > +#define PIN_SD0_D3 PINPOS('M', 1) > +#define PIN_SD0_D2 PINPOS('M', 2) > +#define PIN_UART0_RX PINPOS('M', 4) > +#define PIN_UART0_TX PINPOS('M', 5) > +#define PIN_JTAG_CPU_TRST PINPOS('M', 6) > +#define PIN_PWR_ON PINPOS('M', 11) > +#define PIN_PWR_GPIO2 PINPOS('M', 12) > +#define PIN_PWR_GPIO0 PINPOS('M', 13) > +#define PIN_CLK25M PINPOS('M', 14) > +#define PIN_SD0_PWR_EN PINPOS('N', 1) > +#define PIN_SPK_EN PINPOS('N', 3) > +#define PIN_JTAG_CPU_TCK PINPOS('N', 4) > +#define PIN_JTAG_CPU_TMS PINPOS('N', 6) > +#define PIN_PWR_WAKEUP1 PINPOS('N', 11) > +#define PIN_PWR_WAKEUP0 PINPOS('N', 12) > +#define PIN_PWR_GPIO1 PINPOS('N', 13) > +#define PIN_EMMC_DAT3 PINPOS('P', 1) > +#define PIN_EMMC_DAT0 PINPOS('P', 2) > +#define PIN_EMMC_DAT2 PINPOS('P', 3) > +#define PIN_EMMC_RSTN PINPOS('P', 4) > +#define PIN_AUX0 PINPOS('P', 5) > +#define PIN_IIC0_SDA PINPOS('P', 6) > +#define PIN_PWR_SEQ3 PINPOS('P', 10) > +#define PIN_PWR_VBAT_DET PINPOS('P', 11) > +#define PIN_PWR_SEQ1 PINPOS('P', 12) > +#define PIN_PWR_BUTTON1 PINPOS('P', 13) > +#define PIN_EMMC_DAT1 PINPOS('R', 2) > +#define PIN_EMMC_CMD PINPOS('R', 3) > +#define PIN_EMMC_CLK PINPOS('R', 4) > +#define PIN_IIC0_SCL PINPOS('R', 6) > +#define PIN_GPIO_ZQ PINPOS('R', 10) > +#define PIN_PWR_RSTN PINPOS('R', 11) > +#define PIN_PWR_SEQ2 PINPOS('R', 12) > +#define PIN_XTAL_XIN PINPOS('R', 13) > + > +#endif /* _DT_BINDINGS_PINCTRL_CV1812H_H */ > diff --git a/include/dt-bindings/pinctrl/pinctrl-cv18xx.h b/include/dt-bindings/pinctrl/pinctrl-cv18xx.h > new file mode 100644 > index 000000000000..bc92ad1067ec > --- /dev/null > +++ b/include/dt-bindings/pinctrl/pinctrl-cv18xx.h > @@ -0,0 +1,19 @@ > +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ > +/* > + * Copyright (C) 2023 Sophgo Ltd. > + * > + * Author: Inochi Amaoto <inochiama@outlook.com> > + */ > + > +#ifndef _DT_BINDINGS_PINCTRL_CV18XX_H > +#define _DT_BINDINGS_PINCTRL_CV18XX_H > + > +#define PIN_MUX_INVALD 0xff > + > +#define PINMUX2(pin, mux, mux2) \ > + (((pin) & 0xffff) | (((mux) & 0xff) << 16) | (((mux2) & 0xff) << 24)) > + > +#define PINMUX(pin, mux) \ > + PINMUX2(pin, mux, PIN_MUX_INVALD) > + > +#endif /* _DT_BINDINGS_PINCTRL_CV18XX_H */ > diff --git a/include/dt-bindings/pinctrl/pinctrl-sg2000.h b/include/dt-bindings/pinctrl/pinctrl-sg2000.h > new file mode 100644 > index 000000000000..4871f9a7c6c1 > --- /dev/null > +++ b/include/dt-bindings/pinctrl/pinctrl-sg2000.h > @@ -0,0 +1,127 @@ > +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ > +/* > + * Copyright (C) 2024 Inochi Amaoto <inochiama@outlook.com> > + * > + * This file is generated from vendor pinout definition. > + */ > + > +#ifndef _DT_BINDINGS_PINCTRL_SG2000_H > +#define _DT_BINDINGS_PINCTRL_SG2000_H > + > +#include <dt-bindings/pinctrl/pinctrl-cv18xx.h> > + > +#define PINPOS(row, col) \ > + ((((row) - 'A' + 1) << 8) + ((col) - 1)) > + > +#define PIN_MIPI_TXM4 PINPOS('A', 2) > +#define PIN_MIPIRX0N PINPOS('A', 4) > +#define PIN_MIPIRX3P PINPOS('A', 6) > +#define PIN_MIPIRX4P PINPOS('A', 7) > +#define PIN_VIVO_D2 PINPOS('A', 9) > +#define PIN_VIVO_D3 PINPOS('A', 10) > +#define PIN_VIVO_D10 PINPOS('A', 12) > +#define PIN_USB_VBUS_DET PINPOS('A', 13) > +#define PIN_MIPI_TXP3 PINPOS('B', 1) > +#define PIN_MIPI_TXM3 PINPOS('B', 2) > +#define PIN_MIPI_TXP4 PINPOS('B', 3) > +#define PIN_MIPIRX0P PINPOS('B', 4) > +#define PIN_MIPIRX1N PINPOS('B', 5) > +#define PIN_MIPIRX2N PINPOS('B', 6) > +#define PIN_MIPIRX4N PINPOS('B', 7) > +#define PIN_MIPIRX5N PINPOS('B', 8) > +#define PIN_VIVO_D1 PINPOS('B', 9) > +#define PIN_VIVO_D5 PINPOS('B', 10) > +#define PIN_VIVO_D7 PINPOS('B', 11) > +#define PIN_VIVO_D9 PINPOS('B', 12) > +#define PIN_USB_ID PINPOS('B', 13) > +#define PIN_ETH_RXM PINPOS('B', 15) > +#define PIN_MIPI_TXP2 PINPOS('C', 1) > +#define PIN_MIPI_TXM2 PINPOS('C', 2) > +#define PIN_CAM_PD0 PINPOS('C', 3) > +#define PIN_CAM_MCLK0 PINPOS('C', 4) > +#define PIN_MIPIRX1P PINPOS('C', 5) > +#define PIN_MIPIRX2P PINPOS('C', 6) > +#define PIN_MIPIRX3N PINPOS('C', 7) > +#define PIN_MIPIRX5P PINPOS('C', 8) > +#define PIN_VIVO_CLK PINPOS('C', 9) > +#define PIN_VIVO_D6 PINPOS('C', 10) > +#define PIN_VIVO_D8 PINPOS('C', 11) > +#define PIN_USB_VBUS_EN PINPOS('C', 12) > +#define PIN_ETH_RXP PINPOS('C', 14) > +#define PIN_GPIO_RTX PINPOS('C', 15) > +#define PIN_MIPI_TXP1 PINPOS('D', 1) > +#define PIN_MIPI_TXM1 PINPOS('D', 2) > +#define PIN_CAM_MCLK1 PINPOS('D', 3) > +#define PIN_IIC3_SCL PINPOS('D', 4) > +#define PIN_VIVO_D4 PINPOS('D', 10) > +#define PIN_ETH_TXM PINPOS('D', 14) > +#define PIN_ETH_TXP PINPOS('D', 15) > +#define PIN_MIPI_TXP0 PINPOS('E', 1) > +#define PIN_MIPI_TXM0 PINPOS('E', 2) > +#define PIN_CAM_PD1 PINPOS('E', 4) > +#define PIN_CAM_RST0 PINPOS('E', 5) > +#define PIN_VIVO_D0 PINPOS('E', 10) > +#define PIN_ADC1 PINPOS('E', 13) > +#define PIN_ADC2 PINPOS('E', 14) > +#define PIN_ADC3 PINPOS('E', 15) > +#define PIN_AUD_AOUTL PINPOS('F', 2) > +#define PIN_IIC3_SDA PINPOS('F', 4) > +#define PIN_SD1_D2 PINPOS('F', 14) > +#define PIN_AUD_AOUTR PINPOS('G', 2) > +#define PIN_SD1_D3 PINPOS('G', 13) > +#define PIN_SD1_CLK PINPOS('G', 14) > +#define PIN_SD1_CMD PINPOS('G', 15) > +#define PIN_AUD_AINL_MIC PINPOS('H', 1) > +#define PIN_RSTN PINPOS('H', 12) > +#define PIN_PWM0_BUCK PINPOS('H', 13) > +#define PIN_SD1_D1 PINPOS('H', 14) > +#define PIN_SD1_D0 PINPOS('H', 15) > +#define PIN_AUD_AINR_MIC PINPOS('J', 1) > +#define PIN_IIC2_SCL PINPOS('J', 13) > +#define PIN_IIC2_SDA PINPOS('J', 14) > +#define PIN_SD0_CD PINPOS('K', 2) > +#define PIN_SD0_D1 PINPOS('K', 3) > +#define PIN_UART2_RX PINPOS('K', 13) > +#define PIN_UART2_CTS PINPOS('K', 14) > +#define PIN_UART2_TX PINPOS('K', 15) > +#define PIN_SD0_CLK PINPOS('L', 1) > +#define PIN_SD0_D0 PINPOS('L', 2) > +#define PIN_SD0_CMD PINPOS('L', 3) > +#define PIN_CLK32K PINPOS('L', 14) > +#define PIN_UART2_RTS PINPOS('L', 15) > +#define PIN_SD0_D3 PINPOS('M', 1) > +#define PIN_SD0_D2 PINPOS('M', 2) > +#define PIN_UART0_RX PINPOS('M', 4) > +#define PIN_UART0_TX PINPOS('M', 5) > +#define PIN_JTAG_CPU_TRST PINPOS('M', 6) > +#define PIN_PWR_ON PINPOS('M', 11) > +#define PIN_PWR_GPIO2 PINPOS('M', 12) > +#define PIN_PWR_GPIO0 PINPOS('M', 13) > +#define PIN_CLK25M PINPOS('M', 14) > +#define PIN_SD0_PWR_EN PINPOS('N', 1) > +#define PIN_SPK_EN PINPOS('N', 3) > +#define PIN_JTAG_CPU_TCK PINPOS('N', 4) > +#define PIN_JTAG_CPU_TMS PINPOS('N', 6) > +#define PIN_PWR_WAKEUP1 PINPOS('N', 11) > +#define PIN_PWR_WAKEUP0 PINPOS('N', 12) > +#define PIN_PWR_GPIO1 PINPOS('N', 13) > +#define PIN_EMMC_DAT3 PINPOS('P', 1) > +#define PIN_EMMC_DAT0 PINPOS('P', 2) > +#define PIN_EMMC_DAT2 PINPOS('P', 3) > +#define PIN_EMMC_RSTN PINPOS('P', 4) > +#define PIN_AUX0 PINPOS('P', 5) > +#define PIN_IIC0_SDA PINPOS('P', 6) > +#define PIN_PWR_SEQ3 PINPOS('P', 10) > +#define PIN_PWR_VBAT_DET PINPOS('P', 11) > +#define PIN_PWR_SEQ1 PINPOS('P', 12) > +#define PIN_PWR_BUTTON1 PINPOS('P', 13) > +#define PIN_EMMC_DAT1 PINPOS('R', 2) > +#define PIN_EMMC_CMD PINPOS('R', 3) > +#define PIN_EMMC_CLK PINPOS('R', 4) > +#define PIN_IIC0_SCL PINPOS('R', 6) > +#define PIN_GPIO_ZQ PINPOS('R', 10) > +#define PIN_PWR_RSTN PINPOS('R', 11) > +#define PIN_PWR_SEQ2 PINPOS('R', 12) > +#define PIN_XTAL_XIN PINPOS('R', 13) > + > +#endif /* _DT_BINDINGS_PINCTRL_SG2000_H */ > diff --git a/include/dt-bindings/pinctrl/pinctrl-sg2002.h b/include/dt-bindings/pinctrl/pinctrl-sg2002.h > new file mode 100644 > index 000000000000..3c36cfa0a550 > --- /dev/null > +++ b/include/dt-bindings/pinctrl/pinctrl-sg2002.h > @@ -0,0 +1,79 @@ > +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ > +/* > + * Copyright (C) 2024 Inochi Amaoto <inochiama@outlook.com> > + * > + * This file is generated from vendor pinout definition. > + */ > + > +#ifndef _DT_BINDINGS_PINCTRL_SG2002_H > +#define _DT_BINDINGS_PINCTRL_SG2002_H > + > +#include <dt-bindings/pinctrl/pinctrl-cv18xx.h> > + > +#define PIN_AUD_AINL_MIC 2 > +#define PIN_AUD_AOUTR 4 > +#define PIN_SD0_CLK 6 > +#define PIN_SD0_CMD 7 > +#define PIN_SD0_D0 8 > +#define PIN_SD0_D1 10 > +#define PIN_SD0_D2 11 > +#define PIN_SD0_D3 12 > +#define PIN_SD0_CD 14 > +#define PIN_SD0_PWR_EN 15 > +#define PIN_SPK_EN 17 > +#define PIN_UART0_TX 18 > +#define PIN_UART0_RX 19 > +#define PIN_EMMC_DAT2 20 > +#define PIN_EMMC_CLK 21 > +#define PIN_EMMC_DAT0 22 > +#define PIN_EMMC_DAT3 23 > +#define PIN_EMMC_CMD 24 > +#define PIN_EMMC_DAT1 25 > +#define PIN_JTAG_CPU_TMS 26 > +#define PIN_JTAG_CPU_TCK 27 > +#define PIN_IIC0_SCL 28 > +#define PIN_IIC0_SDA 29 > +#define PIN_AUX0 30 > +#define PIN_GPIO_ZQ 35 > +#define PIN_PWR_VBAT_DET 38 > +#define PIN_PWR_RSTN 39 > +#define PIN_PWR_SEQ1 40 > +#define PIN_PWR_SEQ2 41 > +#define PIN_PWR_WAKEUP0 43 > +#define PIN_PWR_BUTTON1 44 > +#define PIN_XTAL_XIN 45 > +#define PIN_PWR_GPIO0 47 > +#define PIN_PWR_GPIO1 48 > +#define PIN_PWR_GPIO2 49 > +#define PIN_SD1_D3 51 > +#define PIN_SD1_D2 52 > +#define PIN_SD1_D1 53 > +#define PIN_SD1_D0 54 > +#define PIN_SD1_CMD 55 > +#define PIN_SD1_CLK 56 > +#define PIN_PWM0_BUCK 58 > +#define PIN_ADC1 59 > +#define PIN_USB_VBUS_DET 60 > +#define PIN_ETH_TXP 62 > +#define PIN_ETH_TXM 63 > +#define PIN_ETH_RXP 64 > +#define PIN_ETH_RXM 65 > +#define PIN_GPIO_RTX 67 > +#define PIN_MIPIRX4N 72 > +#define PIN_MIPIRX4P 73 > +#define PIN_MIPIRX3N 74 > +#define PIN_MIPIRX3P 75 > +#define PIN_MIPIRX2N 76 > +#define PIN_MIPIRX2P 77 > +#define PIN_MIPIRX1N 78 > +#define PIN_MIPIRX1P 79 > +#define PIN_MIPIRX0N 80 > +#define PIN_MIPIRX0P 81 > +#define PIN_MIPI_TXM2 83 > +#define PIN_MIPI_TXP2 84 > +#define PIN_MIPI_TXM1 85 > +#define PIN_MIPI_TXP1 86 > +#define PIN_MIPI_TXM0 87 > +#define PIN_MIPI_TXP0 88 > + > +#endif /* _DT_BINDINGS_PINCTRL_SG2002_H */ > -- > 2.45.2 >
On Mon, Jul 08, 2024 at 10:29:48AM GMT, Rob Herring wrote: > On Thu, Jul 04, 2024 at 01:46:37PM +0800, Inochi Amaoto wrote: > > Add pinctrl support for Sophgo CV1800 series SoC. > > > > Signed-off-by: Inochi Amaoto <inochiama@outlook.com> > > --- > > .../pinctrl/sophgo,cv1800-pinctrl.yaml | 120 +++++++++++++++++ > > include/dt-bindings/pinctrl/pinctrl-cv1800b.h | 63 +++++++++ > > include/dt-bindings/pinctrl/pinctrl-cv1812h.h | 127 ++++++++++++++++++ > > include/dt-bindings/pinctrl/pinctrl-cv18xx.h | 19 +++ > > include/dt-bindings/pinctrl/pinctrl-sg2000.h | 127 ++++++++++++++++++ > > include/dt-bindings/pinctrl/pinctrl-sg2002.h | 79 +++++++++++ > > 6 files changed, 535 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/pinctrl/sophgo,cv1800-pinctrl.yaml > > create mode 100644 include/dt-bindings/pinctrl/pinctrl-cv1800b.h > > create mode 100644 include/dt-bindings/pinctrl/pinctrl-cv1812h.h > > create mode 100644 include/dt-bindings/pinctrl/pinctrl-cv18xx.h > > create mode 100644 include/dt-bindings/pinctrl/pinctrl-sg2000.h > > create mode 100644 include/dt-bindings/pinctrl/pinctrl-sg2002.h > > > > diff --git a/Documentation/devicetree/bindings/pinctrl/sophgo,cv1800-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/sophgo,cv1800-pinctrl.yaml > > new file mode 100644 > > index 000000000000..b7e4084b78d6 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/pinctrl/sophgo,cv1800-pinctrl.yaml > > @@ -0,0 +1,120 @@ > > +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause > > +%YAML 1.2 > > +--- > > +$id: http://devicetree.org/schemas/pinctrl/sophgo,cv1800-pinctrl.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: Sophgo CV1800 Pin Controller > > + > > +maintainers: > > + - Inochi Amaoto <inochiama@outlook.com> > > + > > +properties: > > + compatible: > > + enum: > > + - sophgo,cv1800b-pinctrl > > + - sophgo,cv1812h-pinctrl > > + - sophgo,sg2000-pinctrl > > + - sophgo,sg2002-pinctrl > > + > > + reg: > > + items: > > + - description: pinctrl for system domain > > + - description: pinctrl for rtc domain > > Based on the example's addresses, this isn't 1 block, but 2 blocks. Is > this really 1 block, 2 instances of the same block, or 2 different > blocks? > It is 2 blocks. According to its document, the pin configuration is cross referenced. > > + > > + reg-names: > > + items: > > + - const: sys > > + - const: rtc > > + > > + resets: > > + maxItems: 1 > > + > > +patternProperties: > > + '-cfg$': > > + type: object > > + patternProperties: > > + '-pins$': > > + type: object > > + description: | > > + A pinctrl node should contain at least one subnode representing the > > It's the '-cfg' node that 'should contain at least one subnode', not > this node. > Thanks, I will update the description. > > + pinctrl groups available on the machine. Each subnode will list the > > + pins it needs, and how they should be configured, with regard to > > + muxer configuration, bias, input enable/disable, input schmitt > > + trigger enable/disable, slew-rate and drive strength. > > + $ref: /schemas/pinctrl/pincfg-node.yaml > > + > > + properties: > > + pinmux: > > + description: | > > + The list of GPIOs and their mux settings that properties in the > > + node apply to. This should be set using the GPIOMUX or GPIOMUX2 > > + macro. > > + $ref: /schemas/pinctrl/pinmux-node.yaml#/properties/pinmux > > + > > + bias-pull-up: > > + type: boolean > > + > > + bias-pull-down: > > + type: boolean > > + > > + drive-strength: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + minimum: 0 > > + maximum: 7 > > + > > + input-schmitt: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + minimum: 0 > > + maximum: 7 > > + > > + slew-rate: > > + enum: [ 0, 1 ] > > + > > + sophgo,bus-holder: > > + description: enable bus holder > > + type: boolean > > + > > + additionalProperties: false > > + > > + additionalProperties: false > > In the indented cases, put these before properties or patternProperties. > > > + > > +required: > > + - compatible > > + - reg > > + - reg-names > > + > > +additionalProperties: false > > + > > +examples: > > + - | > > + #include <dt-bindings/pinctrl/pinctrl-cv1800b.h> > > + > > + soc { > > + #address-cells = <1>; > > + #size-cells = <1>; > > + > > + pinctrl@3001000 { > > + compatible = "sophgo,cv1800b-pinctrl"; > > + reg = <0x03001000 0x1000>, > > + <0x05027000 0x1000>; > > + reg-names = "sys", "rtc"; > > + > > + uart0_cfg: uart0-cfg { > > + uart0-pins { > > + pinmux = <PINMUX(PIN_UART0_TX, 0)>, > > + <PINMUX(PIN_UART0_RX, 0)>; > > + bias-pull-up; > > + drive-strength = <2>; > > + slew-rate = <0>; > > + }; > > + }; > > + }; > > + > > + uart0 { > > + pinctrl-0 = <&uart0_cfg>; > > + pinctrl-names = "default"; > > Not a complete node. Plus the examples for a provider don't show the > consumer side and vice-versa. So drop the node. > > > + }; > > + }; > > + > > +... > > diff --git a/include/dt-bindings/pinctrl/pinctrl-cv1800b.h b/include/dt-bindings/pinctrl/pinctrl-cv1800b.h > > new file mode 100644 > > index 000000000000..0593fc33d470 > > --- /dev/null > > +++ b/include/dt-bindings/pinctrl/pinctrl-cv1800b.h > > @@ -0,0 +1,63 @@ > > +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ > > +/* > > + * Copyright (C) 2024 Inochi Amaoto <inochiama@outlook.com> > > + * > > + * This file is generated from vendor pinout definition. > > + */ > > + > > +#ifndef _DT_BINDINGS_PINCTRL_CV1800B_H > > +#define _DT_BINDINGS_PINCTRL_CV1800B_H > > + > > +#include <dt-bindings/pinctrl/pinctrl-cv18xx.h> > > + > > +#define PIN_AUD_AOUTR 1 > > +#define PIN_SD0_CLK 3 > > +#define PIN_SD0_CMD 4 > > +#define PIN_SD0_D0 5 > > +#define PIN_SD0_D1 7 > > +#define PIN_SD0_D2 8 > > +#define PIN_SD0_D3 9 > > +#define PIN_SD0_CD 11 > > +#define PIN_SD0_PWR_EN 12 > > +#define PIN_SPK_EN 14 > > +#define PIN_UART0_TX 15 > > +#define PIN_UART0_RX 16 > > +#define PIN_SPINOR_HOLD_X 17 > > +#define PIN_SPINOR_SCK 18 > > +#define PIN_SPINOR_MOSI 19 > > +#define PIN_SPINOR_WP_X 20 > > +#define PIN_SPINOR_MISO 21 > > +#define PIN_SPINOR_CS_X 22 > > +#define PIN_IIC0_SCL 23 > > +#define PIN_IIC0_SDA 24 > > +#define PIN_AUX0 25 > > +#define PIN_PWR_VBAT_DET 30 > > +#define PIN_PWR_SEQ2 31 > > +#define PIN_XTAL_XIN 33 > > +#define PIN_SD1_GPIO0 35 > > +#define PIN_SD1_GPIO1 36 > > +#define PIN_SD1_D3 38 > > +#define PIN_SD1_D2 39 > > +#define PIN_SD1_D1 40 > > +#define PIN_SD1_D0 41 > > +#define PIN_SD1_CMD 42 > > +#define PIN_SD1_CLK 43 > > +#define PIN_ADC1 44 > > +#define PIN_USB_VBUS_DET 45 > > +#define PIN_ETH_TXP 47 > > +#define PIN_ETH_TXM 48 > > +#define PIN_ETH_RXP 49 > > +#define PIN_ETH_RXM 50 > > +#define PIN_MIPIRX4N 56 > > +#define PIN_MIPIRX4P 57 > > +#define PIN_MIPIRX3N 58 > > +#define PIN_MIPIRX3P 59 > > +#define PIN_MIPIRX2N 60 > > +#define PIN_MIPIRX2P 61 > > +#define PIN_MIPIRX1N 62 > > +#define PIN_MIPIRX1P 63 > > +#define PIN_MIPIRX0N 64 > > +#define PIN_MIPIRX0P 65 > > +#define PIN_AUD_AINL_MIC 67 > > + > > +#endif /* _DT_BINDINGS_PINCTRL_CV1800B_H */ > > diff --git a/include/dt-bindings/pinctrl/pinctrl-cv1812h.h b/include/dt-bindings/pinctrl/pinctrl-cv1812h.h > > new file mode 100644 > > index 000000000000..2908de347919 > > --- /dev/null > > +++ b/include/dt-bindings/pinctrl/pinctrl-cv1812h.h > > @@ -0,0 +1,127 @@ > > +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ > > +/* > > + * Copyright (C) 2024 Inochi Amaoto <inochiama@outlook.com> > > + * > > + * This file is generated from vendor pinout definition. > > + */ > > + > > +#ifndef _DT_BINDINGS_PINCTRL_CV1812H_H > > +#define _DT_BINDINGS_PINCTRL_CV1812H_H > > + > > +#include <dt-bindings/pinctrl/pinctrl-cv18xx.h> > > + > > +#define PINPOS(row, col) \ > > + ((((row) - 'A' + 1) << 8) + ((col) - 1)) > > + > > +#define PIN_MIPI_TXM4 PINPOS('A', 2) > > +#define PIN_MIPIRX0N PINPOS('A', 4) > > +#define PIN_MIPIRX3P PINPOS('A', 6) > > +#define PIN_MIPIRX4P PINPOS('A', 7) > > +#define PIN_VIVO_D2 PINPOS('A', 9) > > +#define PIN_VIVO_D3 PINPOS('A', 10) > > +#define PIN_VIVO_D10 PINPOS('A', 12) > > +#define PIN_USB_VBUS_DET PINPOS('A', 13) > > +#define PIN_MIPI_TXP3 PINPOS('B', 1) > > +#define PIN_MIPI_TXM3 PINPOS('B', 2) > > +#define PIN_MIPI_TXP4 PINPOS('B', 3) > > +#define PIN_MIPIRX0P PINPOS('B', 4) > > +#define PIN_MIPIRX1N PINPOS('B', 5) > > +#define PIN_MIPIRX2N PINPOS('B', 6) > > +#define PIN_MIPIRX4N PINPOS('B', 7) > > +#define PIN_MIPIRX5N PINPOS('B', 8) > > +#define PIN_VIVO_D1 PINPOS('B', 9) > > +#define PIN_VIVO_D5 PINPOS('B', 10) > > +#define PIN_VIVO_D7 PINPOS('B', 11) > > +#define PIN_VIVO_D9 PINPOS('B', 12) > > +#define PIN_USB_ID PINPOS('B', 13) > > +#define PIN_ETH_RXM PINPOS('B', 15) > > +#define PIN_MIPI_TXP2 PINPOS('C', 1) > > +#define PIN_MIPI_TXM2 PINPOS('C', 2) > > +#define PIN_CAM_PD0 PINPOS('C', 3) > > +#define PIN_CAM_MCLK0 PINPOS('C', 4) > > +#define PIN_MIPIRX1P PINPOS('C', 5) > > +#define PIN_MIPIRX2P PINPOS('C', 6) > > +#define PIN_MIPIRX3N PINPOS('C', 7) > > +#define PIN_MIPIRX5P PINPOS('C', 8) > > +#define PIN_VIVO_CLK PINPOS('C', 9) > > +#define PIN_VIVO_D6 PINPOS('C', 10) > > +#define PIN_VIVO_D8 PINPOS('C', 11) > > +#define PIN_USB_VBUS_EN PINPOS('C', 12) > > +#define PIN_ETH_RXP PINPOS('C', 14) > > +#define PIN_GPIO_RTX PINPOS('C', 15) > > +#define PIN_MIPI_TXP1 PINPOS('D', 1) > > +#define PIN_MIPI_TXM1 PINPOS('D', 2) > > +#define PIN_CAM_MCLK1 PINPOS('D', 3) > > +#define PIN_IIC3_SCL PINPOS('D', 4) > > +#define PIN_VIVO_D4 PINPOS('D', 10) > > +#define PIN_ETH_TXM PINPOS('D', 14) > > +#define PIN_ETH_TXP PINPOS('D', 15) > > +#define PIN_MIPI_TXP0 PINPOS('E', 1) > > +#define PIN_MIPI_TXM0 PINPOS('E', 2) > > +#define PIN_CAM_PD1 PINPOS('E', 4) > > +#define PIN_CAM_RST0 PINPOS('E', 5) > > +#define PIN_VIVO_D0 PINPOS('E', 10) > > +#define PIN_ADC1 PINPOS('E', 13) > > +#define PIN_ADC2 PINPOS('E', 14) > > +#define PIN_ADC3 PINPOS('E', 15) > > +#define PIN_AUD_AOUTL PINPOS('F', 2) > > +#define PIN_IIC3_SDA PINPOS('F', 4) > > +#define PIN_SD1_D2 PINPOS('F', 14) > > +#define PIN_AUD_AOUTR PINPOS('G', 2) > > +#define PIN_SD1_D3 PINPOS('G', 13) > > +#define PIN_SD1_CLK PINPOS('G', 14) > > +#define PIN_SD1_CMD PINPOS('G', 15) > > +#define PIN_AUD_AINL_MIC PINPOS('H', 1) > > +#define PIN_RSTN PINPOS('H', 12) > > +#define PIN_PWM0_BUCK PINPOS('H', 13) > > +#define PIN_SD1_D1 PINPOS('H', 14) > > +#define PIN_SD1_D0 PINPOS('H', 15) > > +#define PIN_AUD_AINR_MIC PINPOS('J', 1) > > +#define PIN_IIC2_SCL PINPOS('J', 13) > > +#define PIN_IIC2_SDA PINPOS('J', 14) > > +#define PIN_SD0_CD PINPOS('K', 2) > > +#define PIN_SD0_D1 PINPOS('K', 3) > > +#define PIN_UART2_RX PINPOS('K', 13) > > +#define PIN_UART2_CTS PINPOS('K', 14) > > +#define PIN_UART2_TX PINPOS('K', 15) > > +#define PIN_SD0_CLK PINPOS('L', 1) > > +#define PIN_SD0_D0 PINPOS('L', 2) > > +#define PIN_SD0_CMD PINPOS('L', 3) > > +#define PIN_CLK32K PINPOS('L', 14) > > +#define PIN_UART2_RTS PINPOS('L', 15) > > +#define PIN_SD0_D3 PINPOS('M', 1) > > +#define PIN_SD0_D2 PINPOS('M', 2) > > +#define PIN_UART0_RX PINPOS('M', 4) > > +#define PIN_UART0_TX PINPOS('M', 5) > > +#define PIN_JTAG_CPU_TRST PINPOS('M', 6) > > +#define PIN_PWR_ON PINPOS('M', 11) > > +#define PIN_PWR_GPIO2 PINPOS('M', 12) > > +#define PIN_PWR_GPIO0 PINPOS('M', 13) > > +#define PIN_CLK25M PINPOS('M', 14) > > +#define PIN_SD0_PWR_EN PINPOS('N', 1) > > +#define PIN_SPK_EN PINPOS('N', 3) > > +#define PIN_JTAG_CPU_TCK PINPOS('N', 4) > > +#define PIN_JTAG_CPU_TMS PINPOS('N', 6) > > +#define PIN_PWR_WAKEUP1 PINPOS('N', 11) > > +#define PIN_PWR_WAKEUP0 PINPOS('N', 12) > > +#define PIN_PWR_GPIO1 PINPOS('N', 13) > > +#define PIN_EMMC_DAT3 PINPOS('P', 1) > > +#define PIN_EMMC_DAT0 PINPOS('P', 2) > > +#define PIN_EMMC_DAT2 PINPOS('P', 3) > > +#define PIN_EMMC_RSTN PINPOS('P', 4) > > +#define PIN_AUX0 PINPOS('P', 5) > > +#define PIN_IIC0_SDA PINPOS('P', 6) > > +#define PIN_PWR_SEQ3 PINPOS('P', 10) > > +#define PIN_PWR_VBAT_DET PINPOS('P', 11) > > +#define PIN_PWR_SEQ1 PINPOS('P', 12) > > +#define PIN_PWR_BUTTON1 PINPOS('P', 13) > > +#define PIN_EMMC_DAT1 PINPOS('R', 2) > > +#define PIN_EMMC_CMD PINPOS('R', 3) > > +#define PIN_EMMC_CLK PINPOS('R', 4) > > +#define PIN_IIC0_SCL PINPOS('R', 6) > > +#define PIN_GPIO_ZQ PINPOS('R', 10) > > +#define PIN_PWR_RSTN PINPOS('R', 11) > > +#define PIN_PWR_SEQ2 PINPOS('R', 12) > > +#define PIN_XTAL_XIN PINPOS('R', 13) > > + > > +#endif /* _DT_BINDINGS_PINCTRL_CV1812H_H */ > > diff --git a/include/dt-bindings/pinctrl/pinctrl-cv18xx.h b/include/dt-bindings/pinctrl/pinctrl-cv18xx.h > > new file mode 100644 > > index 000000000000..bc92ad1067ec > > --- /dev/null > > +++ b/include/dt-bindings/pinctrl/pinctrl-cv18xx.h > > @@ -0,0 +1,19 @@ > > +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ > > +/* > > + * Copyright (C) 2023 Sophgo Ltd. > > + * > > + * Author: Inochi Amaoto <inochiama@outlook.com> > > + */ > > + > > +#ifndef _DT_BINDINGS_PINCTRL_CV18XX_H > > +#define _DT_BINDINGS_PINCTRL_CV18XX_H > > + > > +#define PIN_MUX_INVALD 0xff > > + > > +#define PINMUX2(pin, mux, mux2) \ > > + (((pin) & 0xffff) | (((mux) & 0xff) << 16) | (((mux2) & 0xff) << 24)) > > + > > +#define PINMUX(pin, mux) \ > > + PINMUX2(pin, mux, PIN_MUX_INVALD) > > + > > +#endif /* _DT_BINDINGS_PINCTRL_CV18XX_H */ > > diff --git a/include/dt-bindings/pinctrl/pinctrl-sg2000.h b/include/dt-bindings/pinctrl/pinctrl-sg2000.h > > new file mode 100644 > > index 000000000000..4871f9a7c6c1 > > --- /dev/null > > +++ b/include/dt-bindings/pinctrl/pinctrl-sg2000.h > > @@ -0,0 +1,127 @@ > > +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ > > +/* > > + * Copyright (C) 2024 Inochi Amaoto <inochiama@outlook.com> > > + * > > + * This file is generated from vendor pinout definition. > > + */ > > + > > +#ifndef _DT_BINDINGS_PINCTRL_SG2000_H > > +#define _DT_BINDINGS_PINCTRL_SG2000_H > > + > > +#include <dt-bindings/pinctrl/pinctrl-cv18xx.h> > > + > > +#define PINPOS(row, col) \ > > + ((((row) - 'A' + 1) << 8) + ((col) - 1)) > > + > > +#define PIN_MIPI_TXM4 PINPOS('A', 2) > > +#define PIN_MIPIRX0N PINPOS('A', 4) > > +#define PIN_MIPIRX3P PINPOS('A', 6) > > +#define PIN_MIPIRX4P PINPOS('A', 7) > > +#define PIN_VIVO_D2 PINPOS('A', 9) > > +#define PIN_VIVO_D3 PINPOS('A', 10) > > +#define PIN_VIVO_D10 PINPOS('A', 12) > > +#define PIN_USB_VBUS_DET PINPOS('A', 13) > > +#define PIN_MIPI_TXP3 PINPOS('B', 1) > > +#define PIN_MIPI_TXM3 PINPOS('B', 2) > > +#define PIN_MIPI_TXP4 PINPOS('B', 3) > > +#define PIN_MIPIRX0P PINPOS('B', 4) > > +#define PIN_MIPIRX1N PINPOS('B', 5) > > +#define PIN_MIPIRX2N PINPOS('B', 6) > > +#define PIN_MIPIRX4N PINPOS('B', 7) > > +#define PIN_MIPIRX5N PINPOS('B', 8) > > +#define PIN_VIVO_D1 PINPOS('B', 9) > > +#define PIN_VIVO_D5 PINPOS('B', 10) > > +#define PIN_VIVO_D7 PINPOS('B', 11) > > +#define PIN_VIVO_D9 PINPOS('B', 12) > > +#define PIN_USB_ID PINPOS('B', 13) > > +#define PIN_ETH_RXM PINPOS('B', 15) > > +#define PIN_MIPI_TXP2 PINPOS('C', 1) > > +#define PIN_MIPI_TXM2 PINPOS('C', 2) > > +#define PIN_CAM_PD0 PINPOS('C', 3) > > +#define PIN_CAM_MCLK0 PINPOS('C', 4) > > +#define PIN_MIPIRX1P PINPOS('C', 5) > > +#define PIN_MIPIRX2P PINPOS('C', 6) > > +#define PIN_MIPIRX3N PINPOS('C', 7) > > +#define PIN_MIPIRX5P PINPOS('C', 8) > > +#define PIN_VIVO_CLK PINPOS('C', 9) > > +#define PIN_VIVO_D6 PINPOS('C', 10) > > +#define PIN_VIVO_D8 PINPOS('C', 11) > > +#define PIN_USB_VBUS_EN PINPOS('C', 12) > > +#define PIN_ETH_RXP PINPOS('C', 14) > > +#define PIN_GPIO_RTX PINPOS('C', 15) > > +#define PIN_MIPI_TXP1 PINPOS('D', 1) > > +#define PIN_MIPI_TXM1 PINPOS('D', 2) > > +#define PIN_CAM_MCLK1 PINPOS('D', 3) > > +#define PIN_IIC3_SCL PINPOS('D', 4) > > +#define PIN_VIVO_D4 PINPOS('D', 10) > > +#define PIN_ETH_TXM PINPOS('D', 14) > > +#define PIN_ETH_TXP PINPOS('D', 15) > > +#define PIN_MIPI_TXP0 PINPOS('E', 1) > > +#define PIN_MIPI_TXM0 PINPOS('E', 2) > > +#define PIN_CAM_PD1 PINPOS('E', 4) > > +#define PIN_CAM_RST0 PINPOS('E', 5) > > +#define PIN_VIVO_D0 PINPOS('E', 10) > > +#define PIN_ADC1 PINPOS('E', 13) > > +#define PIN_ADC2 PINPOS('E', 14) > > +#define PIN_ADC3 PINPOS('E', 15) > > +#define PIN_AUD_AOUTL PINPOS('F', 2) > > +#define PIN_IIC3_SDA PINPOS('F', 4) > > +#define PIN_SD1_D2 PINPOS('F', 14) > > +#define PIN_AUD_AOUTR PINPOS('G', 2) > > +#define PIN_SD1_D3 PINPOS('G', 13) > > +#define PIN_SD1_CLK PINPOS('G', 14) > > +#define PIN_SD1_CMD PINPOS('G', 15) > > +#define PIN_AUD_AINL_MIC PINPOS('H', 1) > > +#define PIN_RSTN PINPOS('H', 12) > > +#define PIN_PWM0_BUCK PINPOS('H', 13) > > +#define PIN_SD1_D1 PINPOS('H', 14) > > +#define PIN_SD1_D0 PINPOS('H', 15) > > +#define PIN_AUD_AINR_MIC PINPOS('J', 1) > > +#define PIN_IIC2_SCL PINPOS('J', 13) > > +#define PIN_IIC2_SDA PINPOS('J', 14) > > +#define PIN_SD0_CD PINPOS('K', 2) > > +#define PIN_SD0_D1 PINPOS('K', 3) > > +#define PIN_UART2_RX PINPOS('K', 13) > > +#define PIN_UART2_CTS PINPOS('K', 14) > > +#define PIN_UART2_TX PINPOS('K', 15) > > +#define PIN_SD0_CLK PINPOS('L', 1) > > +#define PIN_SD0_D0 PINPOS('L', 2) > > +#define PIN_SD0_CMD PINPOS('L', 3) > > +#define PIN_CLK32K PINPOS('L', 14) > > +#define PIN_UART2_RTS PINPOS('L', 15) > > +#define PIN_SD0_D3 PINPOS('M', 1) > > +#define PIN_SD0_D2 PINPOS('M', 2) > > +#define PIN_UART0_RX PINPOS('M', 4) > > +#define PIN_UART0_TX PINPOS('M', 5) > > +#define PIN_JTAG_CPU_TRST PINPOS('M', 6) > > +#define PIN_PWR_ON PINPOS('M', 11) > > +#define PIN_PWR_GPIO2 PINPOS('M', 12) > > +#define PIN_PWR_GPIO0 PINPOS('M', 13) > > +#define PIN_CLK25M PINPOS('M', 14) > > +#define PIN_SD0_PWR_EN PINPOS('N', 1) > > +#define PIN_SPK_EN PINPOS('N', 3) > > +#define PIN_JTAG_CPU_TCK PINPOS('N', 4) > > +#define PIN_JTAG_CPU_TMS PINPOS('N', 6) > > +#define PIN_PWR_WAKEUP1 PINPOS('N', 11) > > +#define PIN_PWR_WAKEUP0 PINPOS('N', 12) > > +#define PIN_PWR_GPIO1 PINPOS('N', 13) > > +#define PIN_EMMC_DAT3 PINPOS('P', 1) > > +#define PIN_EMMC_DAT0 PINPOS('P', 2) > > +#define PIN_EMMC_DAT2 PINPOS('P', 3) > > +#define PIN_EMMC_RSTN PINPOS('P', 4) > > +#define PIN_AUX0 PINPOS('P', 5) > > +#define PIN_IIC0_SDA PINPOS('P', 6) > > +#define PIN_PWR_SEQ3 PINPOS('P', 10) > > +#define PIN_PWR_VBAT_DET PINPOS('P', 11) > > +#define PIN_PWR_SEQ1 PINPOS('P', 12) > > +#define PIN_PWR_BUTTON1 PINPOS('P', 13) > > +#define PIN_EMMC_DAT1 PINPOS('R', 2) > > +#define PIN_EMMC_CMD PINPOS('R', 3) > > +#define PIN_EMMC_CLK PINPOS('R', 4) > > +#define PIN_IIC0_SCL PINPOS('R', 6) > > +#define PIN_GPIO_ZQ PINPOS('R', 10) > > +#define PIN_PWR_RSTN PINPOS('R', 11) > > +#define PIN_PWR_SEQ2 PINPOS('R', 12) > > +#define PIN_XTAL_XIN PINPOS('R', 13) > > + > > +#endif /* _DT_BINDINGS_PINCTRL_SG2000_H */ > > diff --git a/include/dt-bindings/pinctrl/pinctrl-sg2002.h b/include/dt-bindings/pinctrl/pinctrl-sg2002.h > > new file mode 100644 > > index 000000000000..3c36cfa0a550 > > --- /dev/null > > +++ b/include/dt-bindings/pinctrl/pinctrl-sg2002.h > > @@ -0,0 +1,79 @@ > > +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ > > +/* > > + * Copyright (C) 2024 Inochi Amaoto <inochiama@outlook.com> > > + * > > + * This file is generated from vendor pinout definition. > > + */ > > + > > +#ifndef _DT_BINDINGS_PINCTRL_SG2002_H > > +#define _DT_BINDINGS_PINCTRL_SG2002_H > > + > > +#include <dt-bindings/pinctrl/pinctrl-cv18xx.h> > > + > > +#define PIN_AUD_AINL_MIC 2 > > +#define PIN_AUD_AOUTR 4 > > +#define PIN_SD0_CLK 6 > > +#define PIN_SD0_CMD 7 > > +#define PIN_SD0_D0 8 > > +#define PIN_SD0_D1 10 > > +#define PIN_SD0_D2 11 > > +#define PIN_SD0_D3 12 > > +#define PIN_SD0_CD 14 > > +#define PIN_SD0_PWR_EN 15 > > +#define PIN_SPK_EN 17 > > +#define PIN_UART0_TX 18 > > +#define PIN_UART0_RX 19 > > +#define PIN_EMMC_DAT2 20 > > +#define PIN_EMMC_CLK 21 > > +#define PIN_EMMC_DAT0 22 > > +#define PIN_EMMC_DAT3 23 > > +#define PIN_EMMC_CMD 24 > > +#define PIN_EMMC_DAT1 25 > > +#define PIN_JTAG_CPU_TMS 26 > > +#define PIN_JTAG_CPU_TCK 27 > > +#define PIN_IIC0_SCL 28 > > +#define PIN_IIC0_SDA 29 > > +#define PIN_AUX0 30 > > +#define PIN_GPIO_ZQ 35 > > +#define PIN_PWR_VBAT_DET 38 > > +#define PIN_PWR_RSTN 39 > > +#define PIN_PWR_SEQ1 40 > > +#define PIN_PWR_SEQ2 41 > > +#define PIN_PWR_WAKEUP0 43 > > +#define PIN_PWR_BUTTON1 44 > > +#define PIN_XTAL_XIN 45 > > +#define PIN_PWR_GPIO0 47 > > +#define PIN_PWR_GPIO1 48 > > +#define PIN_PWR_GPIO2 49 > > +#define PIN_SD1_D3 51 > > +#define PIN_SD1_D2 52 > > +#define PIN_SD1_D1 53 > > +#define PIN_SD1_D0 54 > > +#define PIN_SD1_CMD 55 > > +#define PIN_SD1_CLK 56 > > +#define PIN_PWM0_BUCK 58 > > +#define PIN_ADC1 59 > > +#define PIN_USB_VBUS_DET 60 > > +#define PIN_ETH_TXP 62 > > +#define PIN_ETH_TXM 63 > > +#define PIN_ETH_RXP 64 > > +#define PIN_ETH_RXM 65 > > +#define PIN_GPIO_RTX 67 > > +#define PIN_MIPIRX4N 72 > > +#define PIN_MIPIRX4P 73 > > +#define PIN_MIPIRX3N 74 > > +#define PIN_MIPIRX3P 75 > > +#define PIN_MIPIRX2N 76 > > +#define PIN_MIPIRX2P 77 > > +#define PIN_MIPIRX1N 78 > > +#define PIN_MIPIRX1P 79 > > +#define PIN_MIPIRX0N 80 > > +#define PIN_MIPIRX0P 81 > > +#define PIN_MIPI_TXM2 83 > > +#define PIN_MIPI_TXP2 84 > > +#define PIN_MIPI_TXM1 85 > > +#define PIN_MIPI_TXP1 86 > > +#define PIN_MIPI_TXM0 87 > > +#define PIN_MIPI_TXP0 88 > > + > > +#endif /* _DT_BINDINGS_PINCTRL_SG2002_H */ > > -- > > 2.45.2 > >
diff --git a/Documentation/devicetree/bindings/pinctrl/sophgo,cv1800-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/sophgo,cv1800-pinctrl.yaml new file mode 100644 index 000000000000..b7e4084b78d6 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/sophgo,cv1800-pinctrl.yaml @@ -0,0 +1,120 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/sophgo,cv1800-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sophgo CV1800 Pin Controller + +maintainers: + - Inochi Amaoto <inochiama@outlook.com> + +properties: + compatible: + enum: + - sophgo,cv1800b-pinctrl + - sophgo,cv1812h-pinctrl + - sophgo,sg2000-pinctrl + - sophgo,sg2002-pinctrl + + reg: + items: + - description: pinctrl for system domain + - description: pinctrl for rtc domain + + reg-names: + items: + - const: sys + - const: rtc + + resets: + maxItems: 1 + +patternProperties: + '-cfg$': + type: object + patternProperties: + '-pins$': + type: object + description: | + A pinctrl node should contain at least one subnode representing the + pinctrl groups available on the machine. Each subnode will list the + pins it needs, and how they should be configured, with regard to + muxer configuration, bias, input enable/disable, input schmitt + trigger enable/disable, slew-rate and drive strength. + $ref: /schemas/pinctrl/pincfg-node.yaml + + properties: + pinmux: + description: | + The list of GPIOs and their mux settings that properties in the + node apply to. This should be set using the GPIOMUX or GPIOMUX2 + macro. + $ref: /schemas/pinctrl/pinmux-node.yaml#/properties/pinmux + + bias-pull-up: + type: boolean + + bias-pull-down: + type: boolean + + drive-strength: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 7 + + input-schmitt: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 7 + + slew-rate: + enum: [ 0, 1 ] + + sophgo,bus-holder: + description: enable bus holder + type: boolean + + additionalProperties: false + + additionalProperties: false + +required: + - compatible + - reg + - reg-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/pinctrl/pinctrl-cv1800b.h> + + soc { + #address-cells = <1>; + #size-cells = <1>; + + pinctrl@3001000 { + compatible = "sophgo,cv1800b-pinctrl"; + reg = <0x03001000 0x1000>, + <0x05027000 0x1000>; + reg-names = "sys", "rtc"; + + uart0_cfg: uart0-cfg { + uart0-pins { + pinmux = <PINMUX(PIN_UART0_TX, 0)>, + <PINMUX(PIN_UART0_RX, 0)>; + bias-pull-up; + drive-strength = <2>; + slew-rate = <0>; + }; + }; + }; + + uart0 { + pinctrl-0 = <&uart0_cfg>; + pinctrl-names = "default"; + }; + }; + +... diff --git a/include/dt-bindings/pinctrl/pinctrl-cv1800b.h b/include/dt-bindings/pinctrl/pinctrl-cv1800b.h new file mode 100644 index 000000000000..0593fc33d470 --- /dev/null +++ b/include/dt-bindings/pinctrl/pinctrl-cv1800b.h @@ -0,0 +1,63 @@ +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ +/* + * Copyright (C) 2024 Inochi Amaoto <inochiama@outlook.com> + * + * This file is generated from vendor pinout definition. + */ + +#ifndef _DT_BINDINGS_PINCTRL_CV1800B_H +#define _DT_BINDINGS_PINCTRL_CV1800B_H + +#include <dt-bindings/pinctrl/pinctrl-cv18xx.h> + +#define PIN_AUD_AOUTR 1 +#define PIN_SD0_CLK 3 +#define PIN_SD0_CMD 4 +#define PIN_SD0_D0 5 +#define PIN_SD0_D1 7 +#define PIN_SD0_D2 8 +#define PIN_SD0_D3 9 +#define PIN_SD0_CD 11 +#define PIN_SD0_PWR_EN 12 +#define PIN_SPK_EN 14 +#define PIN_UART0_TX 15 +#define PIN_UART0_RX 16 +#define PIN_SPINOR_HOLD_X 17 +#define PIN_SPINOR_SCK 18 +#define PIN_SPINOR_MOSI 19 +#define PIN_SPINOR_WP_X 20 +#define PIN_SPINOR_MISO 21 +#define PIN_SPINOR_CS_X 22 +#define PIN_IIC0_SCL 23 +#define PIN_IIC0_SDA 24 +#define PIN_AUX0 25 +#define PIN_PWR_VBAT_DET 30 +#define PIN_PWR_SEQ2 31 +#define PIN_XTAL_XIN 33 +#define PIN_SD1_GPIO0 35 +#define PIN_SD1_GPIO1 36 +#define PIN_SD1_D3 38 +#define PIN_SD1_D2 39 +#define PIN_SD1_D1 40 +#define PIN_SD1_D0 41 +#define PIN_SD1_CMD 42 +#define PIN_SD1_CLK 43 +#define PIN_ADC1 44 +#define PIN_USB_VBUS_DET 45 +#define PIN_ETH_TXP 47 +#define PIN_ETH_TXM 48 +#define PIN_ETH_RXP 49 +#define PIN_ETH_RXM 50 +#define PIN_MIPIRX4N 56 +#define PIN_MIPIRX4P 57 +#define PIN_MIPIRX3N 58 +#define PIN_MIPIRX3P 59 +#define PIN_MIPIRX2N 60 +#define PIN_MIPIRX2P 61 +#define PIN_MIPIRX1N 62 +#define PIN_MIPIRX1P 63 +#define PIN_MIPIRX0N 64 +#define PIN_MIPIRX0P 65 +#define PIN_AUD_AINL_MIC 67 + +#endif /* _DT_BINDINGS_PINCTRL_CV1800B_H */ diff --git a/include/dt-bindings/pinctrl/pinctrl-cv1812h.h b/include/dt-bindings/pinctrl/pinctrl-cv1812h.h new file mode 100644 index 000000000000..2908de347919 --- /dev/null +++ b/include/dt-bindings/pinctrl/pinctrl-cv1812h.h @@ -0,0 +1,127 @@ +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ +/* + * Copyright (C) 2024 Inochi Amaoto <inochiama@outlook.com> + * + * This file is generated from vendor pinout definition. + */ + +#ifndef _DT_BINDINGS_PINCTRL_CV1812H_H +#define _DT_BINDINGS_PINCTRL_CV1812H_H + +#include <dt-bindings/pinctrl/pinctrl-cv18xx.h> + +#define PINPOS(row, col) \ + ((((row) - 'A' + 1) << 8) + ((col) - 1)) + +#define PIN_MIPI_TXM4 PINPOS('A', 2) +#define PIN_MIPIRX0N PINPOS('A', 4) +#define PIN_MIPIRX3P PINPOS('A', 6) +#define PIN_MIPIRX4P PINPOS('A', 7) +#define PIN_VIVO_D2 PINPOS('A', 9) +#define PIN_VIVO_D3 PINPOS('A', 10) +#define PIN_VIVO_D10 PINPOS('A', 12) +#define PIN_USB_VBUS_DET PINPOS('A', 13) +#define PIN_MIPI_TXP3 PINPOS('B', 1) +#define PIN_MIPI_TXM3 PINPOS('B', 2) +#define PIN_MIPI_TXP4 PINPOS('B', 3) +#define PIN_MIPIRX0P PINPOS('B', 4) +#define PIN_MIPIRX1N PINPOS('B', 5) +#define PIN_MIPIRX2N PINPOS('B', 6) +#define PIN_MIPIRX4N PINPOS('B', 7) +#define PIN_MIPIRX5N PINPOS('B', 8) +#define PIN_VIVO_D1 PINPOS('B', 9) +#define PIN_VIVO_D5 PINPOS('B', 10) +#define PIN_VIVO_D7 PINPOS('B', 11) +#define PIN_VIVO_D9 PINPOS('B', 12) +#define PIN_USB_ID PINPOS('B', 13) +#define PIN_ETH_RXM PINPOS('B', 15) +#define PIN_MIPI_TXP2 PINPOS('C', 1) +#define PIN_MIPI_TXM2 PINPOS('C', 2) +#define PIN_CAM_PD0 PINPOS('C', 3) +#define PIN_CAM_MCLK0 PINPOS('C', 4) +#define PIN_MIPIRX1P PINPOS('C', 5) +#define PIN_MIPIRX2P PINPOS('C', 6) +#define PIN_MIPIRX3N PINPOS('C', 7) +#define PIN_MIPIRX5P PINPOS('C', 8) +#define PIN_VIVO_CLK PINPOS('C', 9) +#define PIN_VIVO_D6 PINPOS('C', 10) +#define PIN_VIVO_D8 PINPOS('C', 11) +#define PIN_USB_VBUS_EN PINPOS('C', 12) +#define PIN_ETH_RXP PINPOS('C', 14) +#define PIN_GPIO_RTX PINPOS('C', 15) +#define PIN_MIPI_TXP1 PINPOS('D', 1) +#define PIN_MIPI_TXM1 PINPOS('D', 2) +#define PIN_CAM_MCLK1 PINPOS('D', 3) +#define PIN_IIC3_SCL PINPOS('D', 4) +#define PIN_VIVO_D4 PINPOS('D', 10) +#define PIN_ETH_TXM PINPOS('D', 14) +#define PIN_ETH_TXP PINPOS('D', 15) +#define PIN_MIPI_TXP0 PINPOS('E', 1) +#define PIN_MIPI_TXM0 PINPOS('E', 2) +#define PIN_CAM_PD1 PINPOS('E', 4) +#define PIN_CAM_RST0 PINPOS('E', 5) +#define PIN_VIVO_D0 PINPOS('E', 10) +#define PIN_ADC1 PINPOS('E', 13) +#define PIN_ADC2 PINPOS('E', 14) +#define PIN_ADC3 PINPOS('E', 15) +#define PIN_AUD_AOUTL PINPOS('F', 2) +#define PIN_IIC3_SDA PINPOS('F', 4) +#define PIN_SD1_D2 PINPOS('F', 14) +#define PIN_AUD_AOUTR PINPOS('G', 2) +#define PIN_SD1_D3 PINPOS('G', 13) +#define PIN_SD1_CLK PINPOS('G', 14) +#define PIN_SD1_CMD PINPOS('G', 15) +#define PIN_AUD_AINL_MIC PINPOS('H', 1) +#define PIN_RSTN PINPOS('H', 12) +#define PIN_PWM0_BUCK PINPOS('H', 13) +#define PIN_SD1_D1 PINPOS('H', 14) +#define PIN_SD1_D0 PINPOS('H', 15) +#define PIN_AUD_AINR_MIC PINPOS('J', 1) +#define PIN_IIC2_SCL PINPOS('J', 13) +#define PIN_IIC2_SDA PINPOS('J', 14) +#define PIN_SD0_CD PINPOS('K', 2) +#define PIN_SD0_D1 PINPOS('K', 3) +#define PIN_UART2_RX PINPOS('K', 13) +#define PIN_UART2_CTS PINPOS('K', 14) +#define PIN_UART2_TX PINPOS('K', 15) +#define PIN_SD0_CLK PINPOS('L', 1) +#define PIN_SD0_D0 PINPOS('L', 2) +#define PIN_SD0_CMD PINPOS('L', 3) +#define PIN_CLK32K PINPOS('L', 14) +#define PIN_UART2_RTS PINPOS('L', 15) +#define PIN_SD0_D3 PINPOS('M', 1) +#define PIN_SD0_D2 PINPOS('M', 2) +#define PIN_UART0_RX PINPOS('M', 4) +#define PIN_UART0_TX PINPOS('M', 5) +#define PIN_JTAG_CPU_TRST PINPOS('M', 6) +#define PIN_PWR_ON PINPOS('M', 11) +#define PIN_PWR_GPIO2 PINPOS('M', 12) +#define PIN_PWR_GPIO0 PINPOS('M', 13) +#define PIN_CLK25M PINPOS('M', 14) +#define PIN_SD0_PWR_EN PINPOS('N', 1) +#define PIN_SPK_EN PINPOS('N', 3) +#define PIN_JTAG_CPU_TCK PINPOS('N', 4) +#define PIN_JTAG_CPU_TMS PINPOS('N', 6) +#define PIN_PWR_WAKEUP1 PINPOS('N', 11) +#define PIN_PWR_WAKEUP0 PINPOS('N', 12) +#define PIN_PWR_GPIO1 PINPOS('N', 13) +#define PIN_EMMC_DAT3 PINPOS('P', 1) +#define PIN_EMMC_DAT0 PINPOS('P', 2) +#define PIN_EMMC_DAT2 PINPOS('P', 3) +#define PIN_EMMC_RSTN PINPOS('P', 4) +#define PIN_AUX0 PINPOS('P', 5) +#define PIN_IIC0_SDA PINPOS('P', 6) +#define PIN_PWR_SEQ3 PINPOS('P', 10) +#define PIN_PWR_VBAT_DET PINPOS('P', 11) +#define PIN_PWR_SEQ1 PINPOS('P', 12) +#define PIN_PWR_BUTTON1 PINPOS('P', 13) +#define PIN_EMMC_DAT1 PINPOS('R', 2) +#define PIN_EMMC_CMD PINPOS('R', 3) +#define PIN_EMMC_CLK PINPOS('R', 4) +#define PIN_IIC0_SCL PINPOS('R', 6) +#define PIN_GPIO_ZQ PINPOS('R', 10) +#define PIN_PWR_RSTN PINPOS('R', 11) +#define PIN_PWR_SEQ2 PINPOS('R', 12) +#define PIN_XTAL_XIN PINPOS('R', 13) + +#endif /* _DT_BINDINGS_PINCTRL_CV1812H_H */ diff --git a/include/dt-bindings/pinctrl/pinctrl-cv18xx.h b/include/dt-bindings/pinctrl/pinctrl-cv18xx.h new file mode 100644 index 000000000000..bc92ad1067ec --- /dev/null +++ b/include/dt-bindings/pinctrl/pinctrl-cv18xx.h @@ -0,0 +1,19 @@ +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ +/* + * Copyright (C) 2023 Sophgo Ltd. + * + * Author: Inochi Amaoto <inochiama@outlook.com> + */ + +#ifndef _DT_BINDINGS_PINCTRL_CV18XX_H +#define _DT_BINDINGS_PINCTRL_CV18XX_H + +#define PIN_MUX_INVALD 0xff + +#define PINMUX2(pin, mux, mux2) \ + (((pin) & 0xffff) | (((mux) & 0xff) << 16) | (((mux2) & 0xff) << 24)) + +#define PINMUX(pin, mux) \ + PINMUX2(pin, mux, PIN_MUX_INVALD) + +#endif /* _DT_BINDINGS_PINCTRL_CV18XX_H */ diff --git a/include/dt-bindings/pinctrl/pinctrl-sg2000.h b/include/dt-bindings/pinctrl/pinctrl-sg2000.h new file mode 100644 index 000000000000..4871f9a7c6c1 --- /dev/null +++ b/include/dt-bindings/pinctrl/pinctrl-sg2000.h @@ -0,0 +1,127 @@ +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ +/* + * Copyright (C) 2024 Inochi Amaoto <inochiama@outlook.com> + * + * This file is generated from vendor pinout definition. + */ + +#ifndef _DT_BINDINGS_PINCTRL_SG2000_H +#define _DT_BINDINGS_PINCTRL_SG2000_H + +#include <dt-bindings/pinctrl/pinctrl-cv18xx.h> + +#define PINPOS(row, col) \ + ((((row) - 'A' + 1) << 8) + ((col) - 1)) + +#define PIN_MIPI_TXM4 PINPOS('A', 2) +#define PIN_MIPIRX0N PINPOS('A', 4) +#define PIN_MIPIRX3P PINPOS('A', 6) +#define PIN_MIPIRX4P PINPOS('A', 7) +#define PIN_VIVO_D2 PINPOS('A', 9) +#define PIN_VIVO_D3 PINPOS('A', 10) +#define PIN_VIVO_D10 PINPOS('A', 12) +#define PIN_USB_VBUS_DET PINPOS('A', 13) +#define PIN_MIPI_TXP3 PINPOS('B', 1) +#define PIN_MIPI_TXM3 PINPOS('B', 2) +#define PIN_MIPI_TXP4 PINPOS('B', 3) +#define PIN_MIPIRX0P PINPOS('B', 4) +#define PIN_MIPIRX1N PINPOS('B', 5) +#define PIN_MIPIRX2N PINPOS('B', 6) +#define PIN_MIPIRX4N PINPOS('B', 7) +#define PIN_MIPIRX5N PINPOS('B', 8) +#define PIN_VIVO_D1 PINPOS('B', 9) +#define PIN_VIVO_D5 PINPOS('B', 10) +#define PIN_VIVO_D7 PINPOS('B', 11) +#define PIN_VIVO_D9 PINPOS('B', 12) +#define PIN_USB_ID PINPOS('B', 13) +#define PIN_ETH_RXM PINPOS('B', 15) +#define PIN_MIPI_TXP2 PINPOS('C', 1) +#define PIN_MIPI_TXM2 PINPOS('C', 2) +#define PIN_CAM_PD0 PINPOS('C', 3) +#define PIN_CAM_MCLK0 PINPOS('C', 4) +#define PIN_MIPIRX1P PINPOS('C', 5) +#define PIN_MIPIRX2P PINPOS('C', 6) +#define PIN_MIPIRX3N PINPOS('C', 7) +#define PIN_MIPIRX5P PINPOS('C', 8) +#define PIN_VIVO_CLK PINPOS('C', 9) +#define PIN_VIVO_D6 PINPOS('C', 10) +#define PIN_VIVO_D8 PINPOS('C', 11) +#define PIN_USB_VBUS_EN PINPOS('C', 12) +#define PIN_ETH_RXP PINPOS('C', 14) +#define PIN_GPIO_RTX PINPOS('C', 15) +#define PIN_MIPI_TXP1 PINPOS('D', 1) +#define PIN_MIPI_TXM1 PINPOS('D', 2) +#define PIN_CAM_MCLK1 PINPOS('D', 3) +#define PIN_IIC3_SCL PINPOS('D', 4) +#define PIN_VIVO_D4 PINPOS('D', 10) +#define PIN_ETH_TXM PINPOS('D', 14) +#define PIN_ETH_TXP PINPOS('D', 15) +#define PIN_MIPI_TXP0 PINPOS('E', 1) +#define PIN_MIPI_TXM0 PINPOS('E', 2) +#define PIN_CAM_PD1 PINPOS('E', 4) +#define PIN_CAM_RST0 PINPOS('E', 5) +#define PIN_VIVO_D0 PINPOS('E', 10) +#define PIN_ADC1 PINPOS('E', 13) +#define PIN_ADC2 PINPOS('E', 14) +#define PIN_ADC3 PINPOS('E', 15) +#define PIN_AUD_AOUTL PINPOS('F', 2) +#define PIN_IIC3_SDA PINPOS('F', 4) +#define PIN_SD1_D2 PINPOS('F', 14) +#define PIN_AUD_AOUTR PINPOS('G', 2) +#define PIN_SD1_D3 PINPOS('G', 13) +#define PIN_SD1_CLK PINPOS('G', 14) +#define PIN_SD1_CMD PINPOS('G', 15) +#define PIN_AUD_AINL_MIC PINPOS('H', 1) +#define PIN_RSTN PINPOS('H', 12) +#define PIN_PWM0_BUCK PINPOS('H', 13) +#define PIN_SD1_D1 PINPOS('H', 14) +#define PIN_SD1_D0 PINPOS('H', 15) +#define PIN_AUD_AINR_MIC PINPOS('J', 1) +#define PIN_IIC2_SCL PINPOS('J', 13) +#define PIN_IIC2_SDA PINPOS('J', 14) +#define PIN_SD0_CD PINPOS('K', 2) +#define PIN_SD0_D1 PINPOS('K', 3) +#define PIN_UART2_RX PINPOS('K', 13) +#define PIN_UART2_CTS PINPOS('K', 14) +#define PIN_UART2_TX PINPOS('K', 15) +#define PIN_SD0_CLK PINPOS('L', 1) +#define PIN_SD0_D0 PINPOS('L', 2) +#define PIN_SD0_CMD PINPOS('L', 3) +#define PIN_CLK32K PINPOS('L', 14) +#define PIN_UART2_RTS PINPOS('L', 15) +#define PIN_SD0_D3 PINPOS('M', 1) +#define PIN_SD0_D2 PINPOS('M', 2) +#define PIN_UART0_RX PINPOS('M', 4) +#define PIN_UART0_TX PINPOS('M', 5) +#define PIN_JTAG_CPU_TRST PINPOS('M', 6) +#define PIN_PWR_ON PINPOS('M', 11) +#define PIN_PWR_GPIO2 PINPOS('M', 12) +#define PIN_PWR_GPIO0 PINPOS('M', 13) +#define PIN_CLK25M PINPOS('M', 14) +#define PIN_SD0_PWR_EN PINPOS('N', 1) +#define PIN_SPK_EN PINPOS('N', 3) +#define PIN_JTAG_CPU_TCK PINPOS('N', 4) +#define PIN_JTAG_CPU_TMS PINPOS('N', 6) +#define PIN_PWR_WAKEUP1 PINPOS('N', 11) +#define PIN_PWR_WAKEUP0 PINPOS('N', 12) +#define PIN_PWR_GPIO1 PINPOS('N', 13) +#define PIN_EMMC_DAT3 PINPOS('P', 1) +#define PIN_EMMC_DAT0 PINPOS('P', 2) +#define PIN_EMMC_DAT2 PINPOS('P', 3) +#define PIN_EMMC_RSTN PINPOS('P', 4) +#define PIN_AUX0 PINPOS('P', 5) +#define PIN_IIC0_SDA PINPOS('P', 6) +#define PIN_PWR_SEQ3 PINPOS('P', 10) +#define PIN_PWR_VBAT_DET PINPOS('P', 11) +#define PIN_PWR_SEQ1 PINPOS('P', 12) +#define PIN_PWR_BUTTON1 PINPOS('P', 13) +#define PIN_EMMC_DAT1 PINPOS('R', 2) +#define PIN_EMMC_CMD PINPOS('R', 3) +#define PIN_EMMC_CLK PINPOS('R', 4) +#define PIN_IIC0_SCL PINPOS('R', 6) +#define PIN_GPIO_ZQ PINPOS('R', 10) +#define PIN_PWR_RSTN PINPOS('R', 11) +#define PIN_PWR_SEQ2 PINPOS('R', 12) +#define PIN_XTAL_XIN PINPOS('R', 13) + +#endif /* _DT_BINDINGS_PINCTRL_SG2000_H */ diff --git a/include/dt-bindings/pinctrl/pinctrl-sg2002.h b/include/dt-bindings/pinctrl/pinctrl-sg2002.h new file mode 100644 index 000000000000..3c36cfa0a550 --- /dev/null +++ b/include/dt-bindings/pinctrl/pinctrl-sg2002.h @@ -0,0 +1,79 @@ +/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */ +/* + * Copyright (C) 2024 Inochi Amaoto <inochiama@outlook.com> + * + * This file is generated from vendor pinout definition. + */ + +#ifndef _DT_BINDINGS_PINCTRL_SG2002_H +#define _DT_BINDINGS_PINCTRL_SG2002_H + +#include <dt-bindings/pinctrl/pinctrl-cv18xx.h> + +#define PIN_AUD_AINL_MIC 2 +#define PIN_AUD_AOUTR 4 +#define PIN_SD0_CLK 6 +#define PIN_SD0_CMD 7 +#define PIN_SD0_D0 8 +#define PIN_SD0_D1 10 +#define PIN_SD0_D2 11 +#define PIN_SD0_D3 12 +#define PIN_SD0_CD 14 +#define PIN_SD0_PWR_EN 15 +#define PIN_SPK_EN 17 +#define PIN_UART0_TX 18 +#define PIN_UART0_RX 19 +#define PIN_EMMC_DAT2 20 +#define PIN_EMMC_CLK 21 +#define PIN_EMMC_DAT0 22 +#define PIN_EMMC_DAT3 23 +#define PIN_EMMC_CMD 24 +#define PIN_EMMC_DAT1 25 +#define PIN_JTAG_CPU_TMS 26 +#define PIN_JTAG_CPU_TCK 27 +#define PIN_IIC0_SCL 28 +#define PIN_IIC0_SDA 29 +#define PIN_AUX0 30 +#define PIN_GPIO_ZQ 35 +#define PIN_PWR_VBAT_DET 38 +#define PIN_PWR_RSTN 39 +#define PIN_PWR_SEQ1 40 +#define PIN_PWR_SEQ2 41 +#define PIN_PWR_WAKEUP0 43 +#define PIN_PWR_BUTTON1 44 +#define PIN_XTAL_XIN 45 +#define PIN_PWR_GPIO0 47 +#define PIN_PWR_GPIO1 48 +#define PIN_PWR_GPIO2 49 +#define PIN_SD1_D3 51 +#define PIN_SD1_D2 52 +#define PIN_SD1_D1 53 +#define PIN_SD1_D0 54 +#define PIN_SD1_CMD 55 +#define PIN_SD1_CLK 56 +#define PIN_PWM0_BUCK 58 +#define PIN_ADC1 59 +#define PIN_USB_VBUS_DET 60 +#define PIN_ETH_TXP 62 +#define PIN_ETH_TXM 63 +#define PIN_ETH_RXP 64 +#define PIN_ETH_RXM 65 +#define PIN_GPIO_RTX 67 +#define PIN_MIPIRX4N 72 +#define PIN_MIPIRX4P 73 +#define PIN_MIPIRX3N 74 +#define PIN_MIPIRX3P 75 +#define PIN_MIPIRX2N 76 +#define PIN_MIPIRX2P 77 +#define PIN_MIPIRX1N 78 +#define PIN_MIPIRX1P 79 +#define PIN_MIPIRX0N 80 +#define PIN_MIPIRX0P 81 +#define PIN_MIPI_TXM2 83 +#define PIN_MIPI_TXP2 84 +#define PIN_MIPI_TXM1 85 +#define PIN_MIPI_TXP1 86 +#define PIN_MIPI_TXM0 87 +#define PIN_MIPI_TXP0 88 + +#endif /* _DT_BINDINGS_PINCTRL_SG2002_H */
Add pinctrl support for Sophgo CV1800 series SoC. Signed-off-by: Inochi Amaoto <inochiama@outlook.com> --- .../pinctrl/sophgo,cv1800-pinctrl.yaml | 120 +++++++++++++++++ include/dt-bindings/pinctrl/pinctrl-cv1800b.h | 63 +++++++++ include/dt-bindings/pinctrl/pinctrl-cv1812h.h | 127 ++++++++++++++++++ include/dt-bindings/pinctrl/pinctrl-cv18xx.h | 19 +++ include/dt-bindings/pinctrl/pinctrl-sg2000.h | 127 ++++++++++++++++++ include/dt-bindings/pinctrl/pinctrl-sg2002.h | 79 +++++++++++ 6 files changed, 535 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/sophgo,cv1800-pinctrl.yaml create mode 100644 include/dt-bindings/pinctrl/pinctrl-cv1800b.h create mode 100644 include/dt-bindings/pinctrl/pinctrl-cv1812h.h create mode 100644 include/dt-bindings/pinctrl/pinctrl-cv18xx.h create mode 100644 include/dt-bindings/pinctrl/pinctrl-sg2000.h create mode 100644 include/dt-bindings/pinctrl/pinctrl-sg2002.h -- 2.45.2