| Message ID | 20240508-otter-bringup-v1-0-c807d3d931f6@linaro.org |
|---|---|
| Headers | show |
| Series | qcom: initial support for the SHIFTphone 8 | expand |
On Wed, 08 May 2024 01:28:46 +0200, Caleb Connolly wrote: > The SHIFTphone 8 is an upcoming QCM6490 smartphone, it has the following > features: > > * 12GB of RAM, 512GB UFS storage > * 1080p display. > * Hardware kill switches for cameras and microphones > * UART access via type-c SBU pins (enabled by an internal switch) > > Initial support includes: > > * Framebuffer display > * UFS and sdcard storage > * Battery monitoring and USB role switching via pmic glink > * Bluetooth > * Thermals > > Wifi is not yet functional due to a crash in the remoteproc > firmware. > > The serial port on the device can be accessed via the usb-cereal > adapter, it must first be enabled by flipping the switch under the > display. Additional info can be found on the postmarketOS wiki page. > > https://wiki.postmarketos.org/wiki/SHIFT_SHIFTphone_8_(shift-otter) > > --- > Caleb Connolly (2): > dt-bindings: arm: qcom: Add QCM6490 SHIFTphone 8 > arm64: dts: qcom: add QCM6490 SHIFTphone 8 > > Documentation/devicetree/bindings/arm/qcom.yaml | 1 + > arch/arm64/boot/dts/qcom/Makefile | 1 + > arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts | 938 +++++++++++++++++++++++ > 3 files changed, 940 insertions(+) > --- > change-id: 20240507-otter-bringup-388cf3aa7ca5 > base-commit: dccb07f2914cdab2ac3a5b6c98406f765acab803 > > // Caleb (they/them) > > > My bot found new DTB warnings on the .dts files added or changed in this series. Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings are fixed by another series. Ultimately, it is up to the platform maintainer whether these warnings are acceptable or not. No need to reply unless the platform maintainer has comments. If you already ran DT checks and didn't see these error(s), then make sure dt-schema is up to date: pip3 install dtschema --upgrade New warnings running 'make CHECK_DTBS=y qcom/qcm6490-shift-otter.dtb' for 20240508-otter-bringup-v1-0-c807d3d931f6@linaro.org: arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dtb: pcie@1c08000: interrupts: [[0, 307, 4], [0, 308, 4], [0, 309, 4], [0, 312, 4], [0, 313, 4], [0, 314, 4], [0, 374, 4], [0, 375, 4]] is too long from schema $id: http://devicetree.org/schemas/pci/qcom,pcie-sc7280.yaml# arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dtb: pcie@1c08000: interrupt-names:0: 'msi' was expected from schema $id: http://devicetree.org/schemas/pci/qcom,pcie-sc7280.yaml# arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dtb: pcie@1c08000: interrupt-names: ['msi0', 'msi1', 'msi2', 'msi3', 'msi4', 'msi5', 'msi6', 'msi7'] is too long from schema $id: http://devicetree.org/schemas/pci/qcom,pcie-sc7280.yaml# arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dtb: phy@88e3000: 'orientation-switch' does not match any of the regexes: 'pinctrl-[0-9]+' from schema $id: http://devicetree.org/schemas/phy/qcom,usb-snps-femto-v2.yaml# arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dtb: usb@8cf8800: interrupt-names: ['pwr_event', 'hs_phy_irq', 'dp_hs_phy_irq', 'dm_hs_phy_irq'] is too short from schema $id: http://devicetree.org/schemas/usb/qcom,dwc3.yaml# arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dtb: video-codec@aa00000: iommus: [[65, 8576, 32]] is too short from schema $id: http://devicetree.org/schemas/media/qcom,sc7280-venus.yaml#
Hi Caleb, On Wed May 8, 2024 at 1:28 AM CEST, Caleb Connolly wrote: > The SHIFTphone 8 is an upcoming QCM6490 smartphone, it has the following > features: > > * 12GB of RAM, 512GB UFS storage > * 1080p display. > * Hardware kill switches for cameras and microphones > * UART access via type-c SBU pins (enabled by an internal switch) > > Initial support includes: > > * Framebuffer display > * UFS and sdcard storage > * Battery monitoring and USB role switching via pmic glink > * Bluetooth > * Thermals > > Wifi is not yet functional due to a crash in the remoteproc > firmware. > > Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts | 938 +++++++++++++++++++++++ > 2 files changed, 939 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index 7d40ec5e7d21..678e800ac797 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -92,8 +92,9 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-maple.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-poplar.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8998-xiaomi-sagit.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcm6490-fairphone-fp5.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcm6490-idp.dtb > +dtb-$(CONFIG_ARCH_QCOM) += qcm6490-shift-otter.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb > dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb > diff --git a/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts b/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts > new file mode 100644 > index 000000000000..ceef8b9b2414 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts > @@ -0,0 +1,938 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Based largely on Fairphone 5 DT. :) But not sure this needs to be in the file, in the commit message would be enough imo > + * > + * Copyright (c) 2023, Luca Weiss <luca.weiss@fairphone.com> > + * Copyright (c) 2024, Caleb Connolly <caleb.connolly@linaro.org> > + */ > + > +/dts-v1/; > + > +#define PM7250B_SID 8 > +#define PM7250B_SID1 9 > + > +#include <dt-bindings/iio/qcom,spmi-adc7-pm7325.h> > +#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> > +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> > +#include "sc7280.dtsi" Sort the list of PMICs by alphabet? Also I guess you can keep the comments I have in fp5.dts which has the 'real' model of the PMIC > +#include "pmk8350.dtsi" /* PMK7325 */ > +#include "pm7325.dtsi" > +#include "pm8350c.dtsi" > +#include "pm7250b.dtsi" > + > +/* There is also a pmr735a */ This thing also exists on FP5 (named SDR-735-*), but I don't think it's accessible to Linux - or that Linux needs to do anything with it. Downstream I also didn't see something for it iirc. > + > +/delete-node/ &rmtfs_mem; > + > +/ { > + model = "SHIFT SHIFTphone 8"; > + compatible = "shift,otter", "qcom,qcm6490"; > + chassis-type = "handset"; > + > + aliases { > + serial0 = &uart5; > + serial1 = &uart7; > + }; > + > + chosen { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + stdout-path = "serial0:115200n8"; > + > + framebuffer0: framebuffer@a000000 { > + compatible = "simple-framebuffer"; > + reg = <0x0 0xe1000000 0x0 (2400 * 1080 * 4)>; > + width = <1080>; > + height = <2400>; > + stride = <(1080 * 4)>; > + format = "a8r8g8b8"; > + clocks = <&gcc GCC_DISP_HF_AXI_CLK>; > + }; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + pinctrl-0 = <&volume_down_default>; > + pinctrl-names = "default"; > + > + key-volume-up { > + label = "Volume up"; > + gpios = <&pm7325_gpios 6 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEUP>; > + debounce-interval = <15>; > + }; > + }; > + > + pmic-glink { > + compatible = "qcom,qcm6490-pmic-glink", "qcom,pmic-glink"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + connector@0 { > + compatible = "usb-c-connector"; > + reg = <0>; > + power-role = "dual"; > + data-role = "dual"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + pmic_glink_hs_in: endpoint { > + remote-endpoint = <&usb_1_dwc3_hs>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + pmic_glink_ss_in: endpoint { > + remote-endpoint = <&usb_dp_qmpphy_out>; > + }; > + }; > + > + port@2 { > + reg = <2>; > + > + pmic_glink_sbu: endpoint { > + remote-endpoint = <&fsa4480_sbu_mux>; > + }; > + }; > + }; > + }; > + }; > + > + reserved-memory { > + cont_splash_mem: cont-splash@e1000000 { > + reg = <0x0 0xe1000000 0x0 0x2300000>; > + no-map; > + }; > + > + cdsp_mem: cdsp@88f00000 { > + reg = <0x0 0x88f00000 0x0 0x1e00000>; > + no-map; > + }; > + > + rmtfs_mem: memory@f8500000 { rmtfs@ > + compatible = "qcom,rmtfs-mem"; > + reg = <0x0 0xf8500000 0x0 0x600000>; > + no-map; > + > + qcom,client-id = <1>; > + qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>, <QCOM_SCM_VMID_NAV>; > + }; > + }; > + > + thermal-zones { > + camera-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&pmk8350_adc_tm 2>; > + > + trips { > + active-config0 { > + temperature = <125000>; > + hysteresis = <1000>; > + type = "passive"; > + }; > + }; > + }; > + > + chg-skin-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&pm7250b_adc_tm 0>; > + > + trips { > + active-config0 { > + temperature = <125000>; > + hysteresis = <1000>; > + type = "passive"; > + }; > + }; > + }; > + > + conn-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&pm7250b_adc_tm 1>; > + > + trips { > + active-config0 { > + temperature = <125000>; > + hysteresis = <1000>; > + type = "passive"; > + }; > + }; > + }; > + > + quiet-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&pmk8350_adc_tm 1>; > + > + trips { > + active-config0 { > + temperature = <125000>; > + hysteresis = <1000>; > + type = "passive"; > + }; > + }; > + }; > + > + rear-cam-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&pmk8350_adc_tm 4>; > + > + trips { > + active-config0 { > + temperature = <125000>; > + hysteresis = <1000>; > + type = "passive"; > + }; > + }; > + }; > + > + sdm-skin-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&pmk8350_adc_tm 3>; > + > + trips { > + active-config0 { > + temperature = <125000>; > + hysteresis = <1000>; > + type = "passive"; > + }; > + }; > + }; > + > + xo-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&pmk8350_adc_tm 0>; > + > + trips { > + active-config0 { > + temperature = <125000>; > + hysteresis = <1000>; > + type = "passive"; > + }; > + }; > + }; > + }; > +}; > + > +&apps_rsc { > + regulators-0 { > + compatible = "qcom,pm7325-rpmh-regulators"; > + qcom,pmic-id = "b"; > + > + vreg_s1b: smps1 { > + regulator-min-microvolt = <1840000>; > + regulator-max-microvolt = <2040000>; > + }; > + > + vreg_s7b: smps7 { > + regulator-min-microvolt = <535000>; > + regulator-max-microvolt = <1120000>; > + }; > + > + vreg_s8b: smps8 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1500000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_RET>; > + }; > + > + vreg_l1b: ldo1 { > + regulator-min-microvolt = <825000>; > + regulator-max-microvolt = <925000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l2b: ldo2 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <3544000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l3b: ldo3 { > + regulator-min-microvolt = <312000>; > + regulator-max-microvolt = <910000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l6b: ldo6 { > + regulator-min-microvolt = <1140000>; > + regulator-max-microvolt = <1260000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l7b: ldo7 { > + /* Constrained for UFS VCC, at least until UFS driver scales voltage */ > + regulator-min-microvolt = <2952000>; > + regulator-max-microvolt = <2952000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l8b: ldo8 { > + regulator-min-microvolt = <870000>; > + regulator-max-microvolt = <970000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l9b: ldo9 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l11b: ldo11 { > + regulator-min-microvolt = <1504000>; > + regulator-max-microvolt = <2000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l12b: ldo12 { > + regulator-min-microvolt = <751000>; > + regulator-max-microvolt = <824000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l13b: ldo13 { > + regulator-min-microvolt = <530000>; > + regulator-max-microvolt = <824000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l14b: ldo14 { > + regulator-min-microvolt = <1080000>; > + regulator-max-microvolt = <1304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l15b: ldo15 { > + regulator-min-microvolt = <765000>; > + regulator-max-microvolt = <1020000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l16b: ldo16 { > + regulator-min-microvolt = <1100000>; > + regulator-max-microvolt = <1300000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l17b: ldo17 { > + regulator-min-microvolt = <1700000>; > + regulator-max-microvolt = <1900000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l18b: ldo18 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l19b: ldo19 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + regulators-1 { > + compatible = "qcom,pm8350c-rpmh-regulators"; > + qcom,pmic-id = "c"; > + > + vreg_s1c: smps1 { > + regulator-min-microvolt = <2190000>; > + regulator-max-microvolt = <2210000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_s9c: smps9 { > + regulator-min-microvolt = <1010000>; > + regulator-max-microvolt = <1170000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l1c: ldo1 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1980000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l2c: ldo2 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1950000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l3c: ldo3 { > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3400000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l4c: ldo4 { > + regulator-min-microvolt = <1620000>; > + regulator-max-microvolt = <3300000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l5c: ldo5 { > + regulator-min-microvolt = <1620000>; > + regulator-max-microvolt = <3300000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l6c: ldo6 { > + regulator-min-microvolt = <1650000>; > + regulator-max-microvolt = <3544000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l7c: ldo7 { > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3544000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l8c: ldo8 { > + regulator-min-microvolt = <1620000>; > + regulator-max-microvolt = <2000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l9c: ldo9 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <3544000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l10c: ldo10 { > + regulator-min-microvolt = <720000>; > + regulator-max-microvolt = <1050000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l11c: ldo11 { > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <3544000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l12c: ldo12 { > + regulator-min-microvolt = <1650000>; > + regulator-max-microvolt = <2000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l13c: ldo13 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <3544000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_bob: bob { > + regulator-min-microvolt = <3008000>; > + regulator-max-microvolt = <3960000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; > + }; > + }; > +}; > + > +&gcc { > + protected-clocks = <GCC_CFG_NOC_LPASS_CLK>, > + <GCC_EDP_CLKREF_EN>, > + <GCC_MSS_CFG_AHB_CLK>, > + <GCC_MSS_GPLL0_MAIN_DIV_CLK_SRC>, > + <GCC_MSS_OFFLINE_AXI_CLK>, > + <GCC_MSS_Q6SS_BOOT_CLK_SRC>, > + <GCC_MSS_Q6_MEMNOC_AXI_CLK>, > + <GCC_MSS_SNOC_AXI_CLK>, > + <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, > + <GCC_QSPI_CORE_CLK>, > + <GCC_QSPI_CORE_CLK_SRC>, > + <GCC_SEC_CTRL_CLK_SRC>, > + <GCC_WPSS_AHB_BDG_MST_CLK>, > + <GCC_WPSS_AHB_CLK>, > + <GCC_WPSS_RSCP_CLK>; > +}; > + > +&gpi_dma0 { > + status = "okay"; > +}; > + > +&gpi_dma1 { > + status = "okay"; > +}; > + > +&gpu { > + status = "okay"; > +}; > + > +&gpu_zap_shader { > + firmware-name = "qcom/qcm6490/SHIFT/otter/a660_zap.mbn"; > +}; > + > +&i2c1 { > + status = "okay"; > + > + /* PM8008 PMIC @ 8 and 9 */ > + /* rtc6226 FM receiver @ 64 */ > + > + typec-mux@42 { > + compatible = "fcs,fsa4480"; > + reg = <0x42>; > + > + vcc-supply = <&vreg_bob>; > + > + mode-switch; > + orientation-switch; > + > + port { > + fsa4480_sbu_mux: endpoint { > + remote-endpoint = <&pmic_glink_sbu>; > + }; > + }; > + }; > +}; > + > +&i2c4 { > + status = "okay"; > + > + /* tas2563 audio codec @ 4d */ > +}; > + > +&i2c9 { > + status = "okay"; > + > + /* TMS(?) NFC @ 28 */ > + /* Ti drv2624 haptics @ 5a */ > +}; > + > +&i2c13 { > + status = "okay"; > + > + /* focaltech FT3658U @ 38 */ > +}; > + > +&ipa { > + qcom,gsi-loader = "self"; > + memory-region = <&ipa_fw_mem>; > + firmware-name = "qcom/qcm6490/SHIFT/otter/ipa_fws.mbn"; > + status = "okay"; > +}; > + > +&pm7250b_adc { > + channel@4d { > + reg = <ADC5_AMUX_THM1_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + qcom,pre-scaling = <1 1>; > + label = "charger_skin_therm"; > + }; > + > + channel@4f { > + reg = <ADC5_AMUX_THM3_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + qcom,pre-scaling = <1 1>; > + label = "conn_therm"; > + }; > +}; > + > +&pm7250b_adc_tm { > + status = "okay"; > + > + charger-skin-therm@0 { > + reg = <0>; > + io-channels = <&pm7250b_adc ADC5_AMUX_THM1_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > + > + conn-therm@1 { > + reg = <1>; > + io-channels = <&pm7250b_adc ADC5_AMUX_THM3_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > +}; > + > +&pm7325_gpios { > + volume_down_default: volume-down-default-state { > + pins = "gpio6"; > + function = PMIC_GPIO_FUNC_NORMAL; > + power-source = <1>; > + bias-pull-up; > + input-enable; > + }; > +}; > + > +&pmk8350_adc_tm { > + status = "okay"; > + > + xo-therm@0 { > + reg = <0>; > + io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > + > + quiet-therm@1 { > + reg = <1>; > + io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM1_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > + > + cam-flash-therm@2 { > + reg = <2>; > + io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM2_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > + > + sdm-skin-therm@3 { > + reg = <3>; > + io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM3_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > + > + wide-rfc-therm@4 { > + reg = <4>; > + io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM4_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > +}; > + > +&pmk8350_rtc { > + status = "okay"; > +}; > + > +&pmk8350_vadc { > + status = "okay"; > + > + channel@44 { > + reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + qcom,pre-scaling = <1 1>; > + label = "pmk8350_xo_therm"; > + }; > + > + channel@144 { > + reg = <PM7325_ADC7_AMUX_THM1_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + qcom,pre-scaling = <1 1>; > + label = "pm7325_quiet_therm"; > + }; > + > + channel@145 { > + reg = <PM7325_ADC7_AMUX_THM2_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + qcom,pre-scaling = <1 1>; > + label = "pm7325_cam_flash_therm"; > + }; > + > + channel@146 { > + reg = <PM7325_ADC7_AMUX_THM3_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + qcom,pre-scaling = <1 1>; > + label = "pm7325_sdm_skin_therm"; > + }; > + > + channel@147 { > + reg = <PM7325_ADC7_AMUX_THM4_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + qcom,pre-scaling = <1 1>; > + label = "pm7325_wide_rfc_therm"; > + }; > +}; > + > +&pon_pwrkey { > + status = "okay"; > +}; > + > +&pon_resin { > + linux,code = <KEY_VOLUMEDOWN>; > + status = "okay"; > +}; > + > +&qup_spi13_cs { > + drive-strength = <6>; > + bias-disable; > +}; > + > +&qup_spi13_data_clk { > + drive-strength = <6>; > + bias-disable; > +}; > + > +&qup_uart5_rx { > + drive-strength = <2>; > + bias-disable; > +}; > + > +&qup_uart5_tx { > + drive-strength = <2>; > + bias-disable; > +}; > + > +&qupv3_id_0 { > + status = "okay"; > +}; > + > +&qupv3_id_1 { > + status = "okay"; > +}; > + > +&remoteproc_adsp { > + firmware-name = "qcom/qcm6490/SHIFT/otter/adsp.mbn"; > + status = "okay"; > +}; > + > +&remoteproc_cdsp { > + firmware-name = "qcom/qcm6490/SHIFT/otter/cdsp.mbn"; > + status = "okay"; > +}; > + > +&remoteproc_mpss { > + firmware-name = "qcom/qcm6490/SHIFT/otter/modem.mbn"; > + status = "okay"; > +}; > + > +&remoteproc_wpss { > + firmware-name = "qcom/qcm6490/SHIFT/otter/wpss.mbn"; > + /* > + * FIXME: wpss remoteproc crashes during boot with: > + * qcom_q6v5_pas 8a00000.remoteproc: fatal error received: > + * cmnos_thread.c:4645:Asserted in > + * cmnos_allocram.c:cmnos_allocram_base_with_alignment_recurse:497 > + * with Args:0x3,0x3,0x0 > + */ > + status = "disabled"; > +}; > + > +&sdc2_clk { > + drive-strength = <16>; > + bias-disable; > +}; > + > +&sdc2_cmd { > + drive-strength = <10>; > + bias-pull-up; > +}; > + > +&sdc2_data { > + drive-strength = <10>; > + bias-pull-up; > +}; > + > +&sdhc_2 { > + vmmc-supply = <&vreg_l9c>; > + vqmmc-supply = <&vreg_l6c>; > + > + pinctrl-0 = <&sdc2_clk>, <&sdc2_cmd>, <&sdc2_data>; > + pinctrl-1 = <&sdc2_clk_sleep>, <&sdc2_cmd_sleep>, <&sdc2_data_sleep>; > + > + status = "okay"; > +}; > + > +&tlmm { > + /* > + * 48-52: protected by XPU, not sure why. > + */ > + gpio-reserved-ranges = <48 4>; If they really shouldn't be protected from firmware level (fingerprint reader or whatnot), somebody at SHIFT should patch TZ firmware and change the owner from TZ to HLOS. > + > + bluetooth_enable_default: bluetooth-enable-default-state { > + pins = "gpio85"; > + function = "gpio"; > + output-low; > + bias-disable; > + }; > + > + qup_uart7_sleep_cts: qup-uart7-sleep-cts-state { > + pins = "gpio28"; > + function = "gpio"; > + /* > + * Configure a bias-bus-hold on CTS to lower power > + * usage when Bluetooth is turned off. Bus hold will > + * maintain a low power state regardless of whether > + * the Bluetooth module drives the pin in either > + * direction or leaves the pin fully unpowered. > + */ > + bias-bus-hold; > + }; > + > + qup_uart7_sleep_rts: qup-uart7-sleep-rts-state { > + pins = "gpio29"; > + function = "gpio"; > + /* > + * Configure pull-down on RTS. As RTS is active low > + * signal, pull it low to indicate the BT SoC that it > + * can wakeup the system anytime from suspend state by > + * pulling RX low (by sending wakeup bytes). > + */ > + bias-pull-down; > + }; > + > + qup_uart7_sleep_tx: qup-uart7-sleep-tx-state { > + pins = "gpio30"; > + function = "gpio"; > + /* > + * Configure pull-up on TX when it isn't actively driven > + * to prevent BT SoC from receiving garbage during sleep. > + */ > + bias-pull-up; > + }; > + > + qup_uart7_sleep_rx: qup-uart7-sleep-rx-state { > + pins = "gpio31"; > + function = "gpio"; > + /* > + * Configure a pull-up on RX. This is needed to avoid > + * garbage data when the TX pin of the Bluetooth module > + * is floating which may cause spurious wakeups. > + */ > + bias-pull-up; > + }; > + > + sw_ctrl_default: sw-ctrl-default-state { > + pins = "gpio86"; > + function = "gpio"; > + bias-pull-down; > + }; > +}; > + > +&uart5 { > + compatible = "qcom,geni-debug-uart"; This should be redundant soon if the author resends anytime soon https://lore.kernel.org/linux-arm-msm/20240416105650.2626-1-quic_vdadhani@quicinc.com/ Don't see anything wrong with the rest Regards Luca > + status = "okay"; > +}; > + > +&uart7 { > + /delete-property/interrupts; > + interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>, > + <&tlmm 31 IRQ_TYPE_EDGE_FALLING>; > + > + pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>; > + pinctrl-names = "default", "sleep"; > + > + status = "okay"; > + > + bluetooth: bluetooth { > + compatible = "qcom,wcn6750-bt"; > + > + pinctrl-0 = <&bluetooth_enable_default>, <&sw_ctrl_default>; > + pinctrl-names = "default"; > + > + enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; > + swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>; > + > + vddio-supply = <&vreg_l19b>; > + vddaon-supply = <&vreg_s7b>; > + vddbtcxmx-supply = <&vreg_s7b>; > + vddrfacmn-supply = <&vreg_s7b>; > + vddrfa0p8-supply = <&vreg_s7b>; > + vddrfa1p7-supply = <&vreg_s1b>; > + vddrfa1p2-supply = <&vreg_s8b>; > + vddrfa2p2-supply = <&vreg_s1c>; > + vddasd-supply = <&vreg_l11c>; > + > + max-speed = <3200000>; > + }; > +}; > + > +&ufs_mem_hc { > + reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>; > + > + vcc-supply = <&vreg_l7b>; > + vcc-max-microamp = <800000>; > + /* > + * Technically l9b enables an eLDO (supplied by s1b) which then powers > + * VCCQ2 of the UFS. > + */ > + vccq-supply = <&vreg_l9b>; > + vccq-max-microamp = <900000>; > + > + status = "okay"; > +}; > + > +&ufs_mem_phy { > + vdda-phy-supply = <&vreg_l10c>; > + vdda-pll-supply = <&vreg_l6b>; > + > + status = "okay"; > +}; > + > +&usb_1 { > + status = "okay"; > +}; > + > +&usb_1_dwc3 { > + dr_mode = "otg"; > + usb-role-switch; > +}; > + > +&usb_1_dwc3_hs { > + remote-endpoint = <&pmic_glink_hs_in>; > +}; > + > +&usb_dp_qmpphy_out { > + remote-endpoint = <&pmic_glink_ss_in>; > +}; > + > +&usb_1_hsphy { > + vdda-pll-supply = <&vreg_l10c>; > + vdda18-supply = <&vreg_l1c>; > + vdda33-supply = <&vreg_l2b>; > + > + qcom,hs-crossover-voltage-microvolt = <28000>; > + qcom,hs-output-impedance-micro-ohms = <2600000>; > + qcom,hs-rise-fall-time-bp = <5430>; > + qcom,hs-disconnect-bp = <1743>; > + qcom,hs-amplitude-bp = <2430>; > + > + qcom,pre-emphasis-amplitude-bp = <20000>; > + qcom,pre-emphasis-duration-bp = <20000>; > + > + qcom,squelch-detector-bp = <(-2090)>; > + > + orientation-switch; > + > + status = "okay"; > +}; > + > +&usb_1_qmpphy { > + vdda-phy-supply = <&vreg_l6b>; > + vdda-pll-supply = <&vreg_l1b>; > + > + status = "okay"; > +}; > + > +&wifi { > + qcom,ath11k-calibration-variant = "SHIFTphone_8"; > + > + /* FIXME: wpss remoteproc crashes during init */ > + status = "disabled"; > +};
The SHIFTphone 8 is an upcoming QCM6490 smartphone, it has the following features: * 12GB of RAM, 512GB UFS storage * 1080p display. * Hardware kill switches for cameras and microphones * UART access via type-c SBU pins (enabled by an internal switch) Initial support includes: * Framebuffer display * UFS and sdcard storage * Battery monitoring and USB role switching via pmic glink * Bluetooth * Thermals Wifi is not yet functional due to a crash in the remoteproc firmware. The serial port on the device can be accessed via the usb-cereal adapter, it must first be enabled by flipping the switch under the display. Additional info can be found on the postmarketOS wiki page. https://wiki.postmarketos.org/wiki/SHIFT_SHIFTphone_8_(shift-otter) --- Caleb Connolly (2): dt-bindings: arm: qcom: Add QCM6490 SHIFTphone 8 arm64: dts: qcom: add QCM6490 SHIFTphone 8 Documentation/devicetree/bindings/arm/qcom.yaml | 1 + arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts | 938 +++++++++++++++++++++++ 3 files changed, 940 insertions(+) --- change-id: 20240507-otter-bringup-388cf3aa7ca5 base-commit: dccb07f2914cdab2ac3a5b6c98406f765acab803 // Caleb (they/them)