| Message ID | 20240130145037.32672-1-othacehe@gnu.org |
|---|---|
| State | Accepted |
| Commit | 7c1f8ce3956995129a8c36734ba9899ae6d0cb28 |
| Delegated to: | Fabio Estevam |
| Headers | show |
| Series | [v4] board: phytec: phycore-imx93: Add phyBOARD-Segin-i.MX93 support | expand |
Hi Mathieu, Thanks for v4. I have no more remarks. Also tested your v4 on the board. Everything works, even eMMC booting which you were not able to test. With that my Tested-by: can be applied. Tested-by: Primoz Fiser <primoz.fiser@norik.com> BR, Primoz On 30. 01. 24 15:50, Mathieu Othacehe wrote: > Add initial support for the PHYTEC phyBOARD-Segin-i.MX93 board based on > the PHYTEC phyCORE-i.MX93 SoM. > > Supported features: > - 1GB LPDDR4 RAM > - eMMC > - external SD > - FEC Ethernet > - debug UART > - watchdog > > Signed-off-by: Mathieu Othacehe <othacehe@gnu.org> > --- > Hello, > > This new revision fixes the remarks of Primoz. The configuration is now > aligned on the savedefconfig output. The FEC Ethernet is also tested to be > working if this patch is in: > > https://patchwork.ozlabs.org/project/uboot/patch/20240130124337.497748-1-primoz.fiser@norik.com/ > > The proposed patch has been rebased on top of 6faba41. > > Thanks, > > Mathieu > > v3: https://lists.denx.de/pipermail/u-boot/2024-January/544493.html > > arch/arm/dts/Makefile | 3 +- > arch/arm/dts/imx93-phyboard-segin-u-boot.dtsi | 293 ++++ > arch/arm/dts/imx93-phyboard-segin.dts | 117 ++ > arch/arm/dts/imx93-phycore-som.dtsi | 126 ++ > arch/arm/mach-imx/imx9/Kconfig | 6 + > board/phytec/phycore_imx93/Kconfig | 13 + > board/phytec/phycore_imx93/MAINTAINERS | 10 + > board/phytec/phycore_imx93/Makefile | 14 + > board/phytec/phycore_imx93/lpddr4_timing.c | 1546 +++++++++++++++++ > board/phytec/phycore_imx93/phycore-imx93.c | 42 + > board/phytec/phycore_imx93/phycore_imx93.env | 73 + > board/phytec/phycore_imx93/spl.c | 148 ++ > configs/imx93-phyboard-segin_defconfig | 138 ++ > doc/board/phytec/imx93-phyboard-segin.rst | 61 + > doc/board/phytec/index.rst | 1 + > include/configs/phycore_imx93.h | 28 + > 16 files changed, 2618 insertions(+), 1 deletion(-) > create mode 100644 arch/arm/dts/imx93-phyboard-segin-u-boot.dtsi > create mode 100644 arch/arm/dts/imx93-phyboard-segin.dts > create mode 100644 arch/arm/dts/imx93-phycore-som.dtsi > create mode 100644 board/phytec/phycore_imx93/Kconfig > create mode 100644 board/phytec/phycore_imx93/MAINTAINERS > create mode 100644 board/phytec/phycore_imx93/Makefile > create mode 100644 board/phytec/phycore_imx93/lpddr4_timing.c > create mode 100644 board/phytec/phycore_imx93/phycore-imx93.c > create mode 100644 board/phytec/phycore_imx93/phycore_imx93.env > create mode 100644 board/phytec/phycore_imx93/spl.c > create mode 100644 configs/imx93-phyboard-segin_defconfig > create mode 100644 doc/board/phytec/imx93-phyboard-segin.rst > create mode 100644 include/configs/phycore_imx93.h > <snip>
On Tue, 2024-01-30 at 15:50 +0100, Mathieu Othacehe wrote: > Add initial support for the PHYTEC phyBOARD-Segin-i.MX93 board based on > the PHYTEC phyCORE-i.MX93 SoM. > > Supported features: > - 1GB LPDDR4 RAM > - eMMC > - external SD > - FEC Ethernet > - debug UART > - watchdog > > Signed-off-by: Mathieu Othacehe <othacehe@gnu.org> Reviewed-by: Yannic Moog <y.moog@phytec.de> > --- > Hello, > > This new revision fixes the remarks of Primoz. The configuration is now > aligned on the savedefconfig output. The FEC Ethernet is also tested to be > working if this patch is in: > > https://patchwork.ozlabs.org/project/uboot/patch/20240130124337.497748-1-primoz.fiser@norik.com/ > > The proposed patch has been rebased on top of 6faba41. > > Thanks, > > Mathieu > > v3: https://lists.denx.de/pipermail/u-boot/2024-January/544493.html > > arch/arm/dts/Makefile | 3 +- > arch/arm/dts/imx93-phyboard-segin-u-boot.dtsi | 293 ++++ > arch/arm/dts/imx93-phyboard-segin.dts | 117 ++ > arch/arm/dts/imx93-phycore-som.dtsi | 126 ++ > arch/arm/mach-imx/imx9/Kconfig | 6 + > board/phytec/phycore_imx93/Kconfig | 13 + > board/phytec/phycore_imx93/MAINTAINERS | 10 + > board/phytec/phycore_imx93/Makefile | 14 + > board/phytec/phycore_imx93/lpddr4_timing.c | 1546 +++++++++++++++++ > board/phytec/phycore_imx93/phycore-imx93.c | 42 + > board/phytec/phycore_imx93/phycore_imx93.env | 73 + > board/phytec/phycore_imx93/spl.c | 148 ++ > configs/imx93-phyboard-segin_defconfig | 138 ++ > doc/board/phytec/imx93-phyboard-segin.rst | 61 + > doc/board/phytec/index.rst | 1 + > include/configs/phycore_imx93.h | 28 + > 16 files changed, 2618 insertions(+), 1 deletion(-) > create mode 100644 arch/arm/dts/imx93-phyboard-segin-u-boot.dtsi > create mode 100644 arch/arm/dts/imx93-phyboard-segin.dts > create mode 100644 arch/arm/dts/imx93-phycore-som.dtsi > create mode 100644 board/phytec/phycore_imx93/Kconfig > create mode 100644 board/phytec/phycore_imx93/MAINTAINERS > create mode 100644 board/phytec/phycore_imx93/Makefile > create mode 100644 board/phytec/phycore_imx93/lpddr4_timing.c > create mode 100644 board/phytec/phycore_imx93/phycore-imx93.c > create mode 100644 board/phytec/phycore_imx93/phycore_imx93.env > create mode 100644 board/phytec/phycore_imx93/spl.c > create mode 100644 configs/imx93-phyboard-segin_defconfig > create mode 100644 doc/board/phytec/imx93-phyboard-segin.rst > create mode 100644 include/configs/phycore_imx93.h > > <snip>
On Tue, Jan 30, 2024 at 11:50 AM Mathieu Othacehe <othacehe@gnu.org> wrote: > > Add initial support for the PHYTEC phyBOARD-Segin-i.MX93 board based on > the PHYTEC phyCORE-i.MX93 SoM. > > Supported features: > - 1GB LPDDR4 RAM > - eMMC > - external SD > - FEC Ethernet > - debug UART > - watchdog > > Signed-off-by: Mathieu Othacehe <othacehe@gnu.org> Applied, thanks.
Hello Mathieu, after a few months I would like to come back to this patch series from you. I recognized you increased from patch v2 to v3 the CONFIG_SYS_MALLOC_F_LEN from 0x18000 to 0x20000. See v2: https://lists.denx.de/pipermail/u-boot/2024-January/544396.html diff --git a/configs/imx93-phyboard-segin_defconfig b/configs/imx93- phyboard-segin_defconfig [...] +CONFIG_SYS_MALLOC_F_LEN=0x18000 and v3: https://lists.denx.de/pipermail/u-boot/2024-January/544493.html diff --git a/configs/imx93-phyboard-segin_defconfig b/configs/imx93- phyboard-segin_defconfig [...] +CONFIG_SYS_MALLOC_F_LEN=0x20000 I could not find any hint in v3 or later versions why you increased it. Thats why I like to ask you: What was the specific reason for increasing it to 0x20000? I like to understand this to decide whether I should apply it too. Thanks in advance, Christoph On Di, 2024-01-30 at 15:50 +0100, Mathieu Othacehe wrote: > Add initial support for the PHYTEC phyBOARD-Segin-i.MX93 board based > on > the PHYTEC phyCORE-i.MX93 SoM. > > Supported features: > - 1GB LPDDR4 RAM > - eMMC > - external SD > - FEC Ethernet > - debug UART > - watchdog > > Signed-off-by: Mathieu Othacehe <othacehe@gnu.org> > --- > Hello, > > This new revision fixes the remarks of Primoz. The configuration is > now > aligned on the savedefconfig output. The FEC Ethernet is also tested > to be > working if this patch is in: > > https://patchwork.ozlabs.org/project/uboot/patch/20240130124337.497748-1-primoz.fiser@norik.com/ > > The proposed patch has been rebased on top of 6faba41. > > Thanks, > > Mathieu > > v3: https://lists.denx.de/pipermail/u-boot/2024-January/544493.html > > arch/arm/dts/Makefile | 3 +- > arch/arm/dts/imx93-phyboard-segin-u-boot.dtsi | 293 ++++ > arch/arm/dts/imx93-phyboard-segin.dts | 117 ++ > arch/arm/dts/imx93-phycore-som.dtsi | 126 ++ > arch/arm/mach-imx/imx9/Kconfig | 6 + > board/phytec/phycore_imx93/Kconfig | 13 + > board/phytec/phycore_imx93/MAINTAINERS | 10 + > board/phytec/phycore_imx93/Makefile | 14 + > board/phytec/phycore_imx93/lpddr4_timing.c | 1546 > +++++++++++++++++ > board/phytec/phycore_imx93/phycore-imx93.c | 42 + > board/phytec/phycore_imx93/phycore_imx93.env | 73 + > board/phytec/phycore_imx93/spl.c | 148 ++ > configs/imx93-phyboard-segin_defconfig | 138 ++ > doc/board/phytec/imx93-phyboard-segin.rst | 61 + > doc/board/phytec/index.rst | 1 + > include/configs/phycore_imx93.h | 28 + > 16 files changed, 2618 insertions(+), 1 deletion(-) > create mode 100644 arch/arm/dts/imx93-phyboard-segin-u-boot.dtsi > create mode 100644 arch/arm/dts/imx93-phyboard-segin.dts > create mode 100644 arch/arm/dts/imx93-phycore-som.dtsi > create mode 100644 board/phytec/phycore_imx93/Kconfig > create mode 100644 board/phytec/phycore_imx93/MAINTAINERS > create mode 100644 board/phytec/phycore_imx93/Makefile > create mode 100644 board/phytec/phycore_imx93/lpddr4_timing.c > create mode 100644 board/phytec/phycore_imx93/phycore-imx93.c > create mode 100644 board/phytec/phycore_imx93/phycore_imx93.env > create mode 100644 board/phytec/phycore_imx93/spl.c > create mode 100644 configs/imx93-phyboard-segin_defconfig > create mode 100644 doc/board/phytec/imx93-phyboard-segin.rst > create mode 100644 include/configs/phycore_imx93.h > > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile > index 50f35e3db3f..1a20031b063 100644 > --- a/arch/arm/dts/Makefile > +++ b/arch/arm/dts/Makefile > @@ -1130,7 +1130,8 @@ dtb-$(CONFIG_ARCH_IMX8M) += \ > > dtb-$(CONFIG_ARCH_IMX9) += \ > imx93-11x11-evk.dtb \ > - imx93-var-som-symphony.dtb > + imx93-var-som-symphony.dtb \ > + imx93-phyboard-segin.dtb > > dtb-$(CONFIG_ARCH_IMXRT) += imxrt1050-evk.dtb \ > imxrt1020-evk.dtb \ > diff --git a/arch/arm/dts/imx93-phyboard-segin-u-boot.dtsi > b/arch/arm/dts/imx93-phyboard-segin-u-boot.dtsi > new file mode 100644 > index 00000000000..8bf28c2de87 > --- /dev/null > +++ b/arch/arm/dts/imx93-phyboard-segin-u-boot.dtsi > @@ -0,0 +1,293 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2023 PHYTEC Messtechnik GmbH > + * Christoph Stoidner <c.stoidner@phytec.de> > + * > + * Product homepage: > + * phyBOARD-Segin carrier board is reused for the i.MX93 design. > + * > https://www.phytec.eu/en/produkte/single-board-computer/phyboard-segin-imx6ul/ > + */ > + > +#include "imx93-u-boot.dtsi" > + > +/ { > + wdt-reboot { > + compatible = "wdt-reboot"; > + wdt = <&wdog3>; > + bootph-pre-ram; > + bootph-some-ram; > + }; > + > + aliases { > + ethernet0 = &fec; > + ethernet1 = &eqos; > + }; > + > + firmware { > + optee { > + compatible = "linaro,optee-tz"; > + method = "smc"; > + }; > + }; > +}; > + > +&{/soc@0} { > + bootph-all; > + bootph-pre-ram; > +}; > + > +&aips1 { > + bootph-pre-ram; > + bootph-all; > +}; > + > +&aips2 { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&aips3 { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&iomuxc { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +®_usdhc2_vmmc { > + u-boot,off-on-delay-us = <20000>; > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&pinctrl_reg_usdhc2_vmmc { > + bootph-pre-ram; > +}; > + > +&pinctrl_uart1 { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&pinctrl_usdhc1 { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&pinctrl_usdhc2_cd { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&pinctrl_usdhc2_default { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&pinctrl_usdhc2_100mhz { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&pinctrl_usdhc2_200mhz { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&gpio1 { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&gpio2 { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&gpio3 { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&gpio4 { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&lpuart1 { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&usdhc1 { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&usdhc2 { > + bootph-pre-ram; > + bootph-some-ram; > + fsl,signal-voltage-switch-extra-delay-ms = <8>; > +}; > + > +&lpi2c1 { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&lpi2c2 { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&lpi2c3 { > + bootph-pre-ram; > + bootph-some-ram; > +}; > + > +&s4muap { > + bootph-pre-ram; > + bootph-some-ram; > + status = "okay"; > +}; > + > +&clk { > + bootph-all; > + bootph-pre-ram; > + /delete-property/ assigned-clocks; > + /delete-property/ assigned-clock-rates; > + /delete-property/ assigned-clock-parents; > +}; > + > +&osc_32k { > + bootph-all; > + bootph-pre-ram; > +}; > + > +&osc_24m { > + bootph-all; > + bootph-pre-ram; > +}; > + > +&clk_ext1 { > + bootph-all; > + bootph-pre-ram; > +}; > + > +&wdog3 { > + bootph-all; > + bootph-pre-ram; > +}; > + > +/* > + * The two nodes below won't be needed once nxp,pca9451a > + * support is added to the Linux kernel. > + */ > +&iomuxc { > + pinctrl_lpi2c3: lpi2c3grp { > + bootph-pre-ram; > + fsl,pins = < > + MX93_PAD_GPIO_IO28__LPI2C3_SDA 0x400 > 00b9e > + MX93_PAD_GPIO_IO29__LPI2C3_SCL 0x400 > 00b9e > + >; > + }; > + > + pinctrl_pmic: pmicgrp { > + bootph-pre-ram; > + fsl,pins = < > + MX93_PAD_ENET2_RD3__GPIO4_IO27 > 0x31e > + >; > + }; > +}; > + > +&lpi2c3 { > + bootph-pre-ram; > + bootph-some-ram; > + clock-frequency = <400000>; > + pinctrl-names = "default", "sleep"; > + pinctrl-0 = <&pinctrl_lpi2c3>; > + pinctrl-1 = <&pinctrl_lpi2c3>; > + status = "okay"; > + > + pmic@25 { > + bootph-pre-ram; > + bootph-some-ram; > + compatible = "nxp,pca9451a"; > + reg = <0x25>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_pmic>; > + interrupt-parent = <&gpio4>; > + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; > + > + regulators { > + bootph-pre-ram; > + bootph-some-ram; > + buck1: BUCK1 { > + regulator-name = "VDD_SOC"; > + regulator-min-microvolt = <610000>; > + regulator-max-microvolt = <950000>; > + regulator-boot-on; > + regulator-always-on; > + regulator-ramp-delay = <3125>; > + }; > + > + buck2: BUCK2 { > + regulator-name = "VDDQ_0V6"; > + regulator-min-microvolt = <600000>; > + regulator-max-microvolt = <600000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + buck4: BUCK4 { > + regulator-name = "VDD_3V3_BUCK"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + buck5: BUCK5 { > + regulator-name = "VDD_1V8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + buck6: BUCK6 { > + regulator-name = "VDD_1V1"; > + regulator-min-microvolt = <1100000>; > + regulator-max-microvolt = <1100000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + ldo1: LDO1 { > + regulator-name = "PMIC_SNVS_1V8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + ldo4: LDO4 { > + regulator-name = "VDD_0V8"; > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <800000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + ldo5: LDO5 { > + regulator-name = "NVCC_SD2"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + }; > + }; > +}; > diff --git a/arch/arm/dts/imx93-phyboard-segin.dts > b/arch/arm/dts/imx93-phyboard-segin.dts > new file mode 100644 > index 00000000000..85fb188b057 > --- /dev/null > +++ b/arch/arm/dts/imx93-phyboard-segin.dts > @@ -0,0 +1,117 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2023 PHYTEC Messtechnik GmbH > + * Author: Wadim Egorov <w.egorov@phytec.de>, Christoph Stoidner > <c.stoidner@phytec.de> > + * Copyright (C) 2024 Mathieu Othacehe <m.othacehe@gmail.com> > + * > + * Product homepage: > + * phyBOARD-Segin carrier board is reused for the i.MX93 design. > + * > https://www.phytec.eu/en/produkte/single-board-computer/phyboard-segin-imx6ul/ > + */ > +/dts-v1/; > + > +#include "imx93-phycore-som.dtsi" > + > +/{ > + model = "PHYTEC phyBOARD-Segin-i.MX93"; > + compatible = "phytec,imx93-phyboard-segin", "phytec,imx93- > phycore-som", > + "fsl,imx93"; > + > + chosen { > + stdout-path = &lpuart1; > + }; > + > + reg_usdhc2_vmmc: regulator-usdhc2 { > + compatible = "regulator-fixed"; > + enable-active-high; > + gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-name = "VCC_SD"; > + }; > +}; > + > +/* Console */ > +&lpuart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart1>; > + status = "okay"; > +}; > + > +/* eMMC */ > +&usdhc1 { > + no-1-8-v; > +}; > + > +/* SD-Card */ > +&usdhc2 { > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc2_default>, <&pinctrl_usdhc2_cd>; > + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_cd>; > + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_cd>; > + bus-width = <4>; > + cd-gpios = <&gpio3 0 GPIO_ACTIVE_LOW>; > + no-mmc; > + no-sdio; > + vmmc-supply = <®_usdhc2_vmmc>; > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl_uart1: uart1grp { > + fsl,pins = < > + MX93_PAD_UART1_RXD__LPUART1_RX 0x31e > + MX93_PAD_UART1_TXD__LPUART1_TX 0x30e > + >; > + }; > + > + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp { > + fsl,pins = < > + MX93_PAD_SD2_RESET_B__GPIO3_IO07 0x31e > + >; > + }; > + > + pinctrl_usdhc2_cd: usdhc2cdgrp { > + fsl,pins = < > + MX93_PAD_SD2_CD_B__GPIO3_IO00 0x31e > + >; > + }; > + > + pinctrl_usdhc2_default: usdhc2grp { > + fsl,pins = < > + MX93_PAD_SD2_CLK__USDHC2_CLK 0x179 > e > + MX93_PAD_SD2_CMD__USDHC2_CMD 0x139 > e > + MX93_PAD_SD2_DATA0__USDHC2_DATA0 0x138 > e > + MX93_PAD_SD2_DATA1__USDHC2_DATA1 0x138 > e > + MX93_PAD_SD2_DATA2__USDHC2_DATA2 0x138 > e > + MX93_PAD_SD2_DATA3__USDHC2_DATA3 0x139 > e > + MX93_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e > + >; > + }; > + > + pinctrl_usdhc2_100mhz: usdhc2grp { > + fsl,pins = < > + MX93_PAD_SD2_CLK__USDHC2_CLK > 0x179e > + MX93_PAD_SD2_CMD__USDHC2_CMD > 0x139e > + MX93_PAD_SD2_DATA0__USDHC2_DATA0 > 0x138e > + MX93_PAD_SD2_DATA1__USDHC2_DATA1 > 0x138e > + MX93_PAD_SD2_DATA2__USDHC2_DATA2 > 0x139e > + MX93_PAD_SD2_DATA3__USDHC2_DATA3 > 0x139e > + MX93_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e > + >; > + }; > + > + pinctrl_usdhc2_200mhz: usdhc2grp { > + fsl,pins = < > + MX93_PAD_SD2_CLK__USDHC2_CLK > 0x178e > + MX93_PAD_SD2_CMD__USDHC2_CMD > 0x139e > + MX93_PAD_SD2_DATA0__USDHC2_DATA0 > 0x139e > + MX93_PAD_SD2_DATA1__USDHC2_DATA1 > 0x139e > + MX93_PAD_SD2_DATA2__USDHC2_DATA2 > 0x139e > + MX93_PAD_SD2_DATA3__USDHC2_DATA3 > 0x139e > + MX93_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e > + >; > + }; > +}; > diff --git a/arch/arm/dts/imx93-phycore-som.dtsi > b/arch/arm/dts/imx93-phycore-som.dtsi > new file mode 100644 > index 00000000000..88c2657b50e > --- /dev/null > +++ b/arch/arm/dts/imx93-phycore-som.dtsi > @@ -0,0 +1,126 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2023 PHYTEC Messtechnik GmbH > + * Author: Wadim Egorov <w.egorov@phytec.de>, Christoph Stoidner > <c.stoidner@phytec.de> > + * Copyright (C) 2024 Mathieu Othacehe <m.othacehe@gmail.com> > + * > + * Product homepage: > + * > https://www.phytec.eu/en/produkte/system-on-modules/phycore-imx-91-93/ > + */ > + > +#include <dt-bindings/leds/common.h> > + > +#include "imx93.dtsi" > + > +/{ > + model = "PHYTEC phyCORE-i.MX93"; > + compatible = "phytec,imx93-phycore-som", "fsl,imx93"; > + > + reserved-memory { > + ranges; > + #address-cells = <2>; > + #size-cells = <2>; > + > + linux,cma { > + compatible = "shared-dma-pool"; > + reusable; > + alloc-ranges = <0 0x80000000 0 0x40000000>; > + size = <0 0x10000000>; > + linux,cma-default; > + }; > + }; > + > + leds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_leds>; > + > + led-0 { > + color = <LED_COLOR_ID_GREEN>; > + function = LED_FUNCTION_HEARTBEAT; > + gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "heartbeat"; > + }; > + }; > +}; > + > +/* Ethernet */ > +&fec { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_fec>; > + phy-mode = "rmii"; > + phy-handle = <ðphy1>; > + fsl,magic-packet; > + assigned-clocks = <&clk IMX93_CLK_ENET_TIMER1>, > + <&clk IMX93_CLK_ENET_REF>, > + <&clk IMX93_CLK_ENET_REF_PHY>; > + assigned-clock-parents = <&clk IMX93_CLK_SYS_PLL_PFD1_DIV2>, > + <&clk IMX93_CLK_SYS_PLL_PFD1_DIV2>, > + <&clk IMX93_CLK_SYS_PLL_PFD1_DIV2>; > + assigned-clock-rates = <100000000>, <50000000>, <50000000>; > + status = "okay"; > + > + mdio: mdio { > + clock-frequency = <5000000>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + ethphy1: ethernet-phy@1 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <1>; > + }; > + }; > +}; > + > +/* eMMC */ > +&usdhc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usdhc1>; > + bus-width = <8>; > + non-removable; > + status = "okay"; > +}; > + > +/* Watchdog */ > +&wdog3 { > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl_fec: fecgrp { > + fsl,pins = < > + MX93_PAD_ENET2_MDC__ENET1_MDC > 0x50e > + MX93_PAD_ENET2_MDIO__ENET1_MDIO > 0x502 > + MX93_PAD_ENET2_RD0__ENET1_RGMII_RD0 > 0x57e > + MX93_PAD_ENET2_RD1__ENET1_RGMII_RD1 > 0x57e > + MX93_PAD_ENET2_RXC__ENET1_RX_ER > 0x5fe > + MX93_PAD_ENET2_RX_CTL__ENET1_RGMII_RX_CTL > 0x57e > + MX93_PAD_ENET2_TD0__ENET1_RGMII_TD0 > 0x50e > + MX93_PAD_ENET2_TD1__ENET1_RGMII_TD1 > 0x50e > + MX93_PAD_ENET2_TX_CTL__ENET1_RGMII_TX_CTL > 0x50e > + MX93_PAD_ENET2_TD2__ENET1_TX_CLK > 0x4000050e > + >; > + }; > + > + pinctrl_leds: ledsgrp { > + fsl,pins = < > + MX93_PAD_I2C1_SDA__GPIO1_IO01 0x31e > + >; > + }; > + > + pinctrl_usdhc1: usdhc1grp { > + fsl,pins = < > + MX93_PAD_SD1_CLK__USDHC1_CLK 0x179 > e > + MX93_PAD_SD1_CMD__USDHC1_CMD 0x138 > 6 > + MX93_PAD_SD1_DATA0__USDHC1_DATA0 0x138 > e > + MX93_PAD_SD1_DATA1__USDHC1_DATA1 0x138 > 6 > + MX93_PAD_SD1_DATA2__USDHC1_DATA2 0x138 > e > + MX93_PAD_SD1_DATA3__USDHC1_DATA3 0x138 > 6 > + MX93_PAD_SD1_DATA4__USDHC1_DATA4 0x138 > 6 > + MX93_PAD_SD1_DATA5__USDHC1_DATA5 0x138 > 6 > + MX93_PAD_SD1_DATA6__USDHC1_DATA6 0x138 > 6 > + MX93_PAD_SD1_DATA7__USDHC1_DATA7 0x138 > 6 > + MX93_PAD_SD1_STROBE__USDHC1_STROBE 0x179 > e > + >; > + }; > +}; > diff --git a/arch/arm/mach-imx/imx9/Kconfig b/arch/arm/mach- > imx/imx9/Kconfig > index 961d6f527ab..b79485f1f75 100644 > --- a/arch/arm/mach-imx/imx9/Kconfig > +++ b/arch/arm/mach-imx/imx9/Kconfig > @@ -37,9 +37,15 @@ config TARGET_IMX93_VAR_SOM > select IMX93 > select IMX9_LPDDR4X > > +config TARGET_PHYCORE_IMX93 > + bool "phycore_imx93" > + select IMX93 > + select IMX9_LPDDR4X > + > endchoice > > source "board/freescale/imx93_evk/Kconfig" > +source "board/phytec/phycore_imx93/Kconfig" > source "board/variscite/imx93_var_som/Kconfig" > > endif > diff --git a/board/phytec/phycore_imx93/Kconfig > b/board/phytec/phycore_imx93/Kconfig > new file mode 100644 > index 00000000000..a70104cb798 > --- /dev/null > +++ b/board/phytec/phycore_imx93/Kconfig > @@ -0,0 +1,13 @@ > + > +if TARGET_PHYCORE_IMX93 > + > +config SYS_BOARD > + default "phycore_imx93" > + > +config SYS_VENDOR > + default "phytec" > + > +config SYS_CONFIG_NAME > + default "phycore_imx93" > + > +endif > diff --git a/board/phytec/phycore_imx93/MAINTAINERS > b/board/phytec/phycore_imx93/MAINTAINERS > new file mode 100644 > index 00000000000..9e91a29dc31 > --- /dev/null > +++ b/board/phytec/phycore_imx93/MAINTAINERS > @@ -0,0 +1,10 @@ > +phyCORE-i.MX93 > +M: Mathieu Othacehe <m.othacehe@gmail.com> > +W: > https://www.phytec.eu/en/produkte/system-on-modules/phycore-imx-91-93/ > +S: Maintained > +F: arch/arm/dts/imx93-phyboard-segin.dts > +F: arch/arm/dts/imx93-phycore-som.dtsi > +F: arch/arm/dts/imx93-phyboard-segin-u-boot.dtsi > +F: board/phytec/phycore_imx93/ > +F: configs/imx93-phyboard-segin_defconfig > +F: include/configs/phycore_imx93.h > diff --git a/board/phytec/phycore_imx93/Makefile > b/board/phytec/phycore_imx93/Makefile > new file mode 100644 > index 00000000000..ce35326a156 > --- /dev/null > +++ b/board/phytec/phycore_imx93/Makefile > @@ -0,0 +1,14 @@ > +# > +# Copyright 2022 NXP > +# Copyright (C) 2023 PHYTEC Messtechnik GmbH > +# Christoph Stoidner <c.stoidner@phytec.de> > +# Copyright (C) 2024 Mathieu Othacehe <m.othacehe@gmail.com> > +# > +# SPDX-License-Identifier: GPL-2.0+ > +# > + > +obj-y += phycore-imx93.o > + > +ifdef CONFIG_SPL_BUILD > +obj-y += spl.o lpddr4_timing.o > +endif > diff --git a/board/phytec/phycore_imx93/lpddr4_timing.c > b/board/phytec/phycore_imx93/lpddr4_timing.c > new file mode 100644 > index 00000000000..2111972a40e > --- /dev/null > +++ b/board/phytec/phycore_imx93/lpddr4_timing.c > @@ -0,0 +1,1546 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * Copyright 2023 NXP > + * Copyright (C) 2023 PHYTEC Messtechnik GmbH > + * Christoph Stoidner <c.stoidner@phytec.de> > + * > + * Code generated with DDR Tool v1.0.0. > + */ > + > +#include <linux/kernel.h> > +#include <asm/arch/ddr.h> > + > +static struct dram_cfg_param ddr_ddrc_cfg[] = { > + /** Initialize DDRC registers **/ > + {0x4e300110, 0x44100001}, > + {0x4e300000, 0x8000bf}, > + {0x4e300008, 0x0}, > + {0x4e300080, 0x80000412}, > + {0x4e300084, 0x0}, > + {0x4e300114, 0x1002}, > + {0x4e300260, 0x4080}, > + {0x4e300f04, 0x80}, > + {0x4e300800, 0x43b30002}, > + {0x4e300804, 0x1f1f1f1f}, > + {0x4e301000, 0x0}, > + {0x4e301240, 0x0}, > + {0x4e301244, 0x0}, > + {0x4e301248, 0x0}, > + {0x4e30124c, 0x0}, > + {0x4e301250, 0x0}, > + {0x4e301254, 0x0}, > + {0x4e301258, 0x0}, > + {0x4e30125c, 0x0}, > + > +}; > + > +/* dram fsp cfg */ > +static struct dram_fsp_cfg ddr_dram_fsp_cfg[] = { > + { > + { > + {0x4e300100, 0x24A0421B}, > + {0x4e300104, 0xF8EE001B}, > + {0x4e300108, 0x2F263233}, > + {0x4e30010C, 0x0005E18B}, > + {0x4e300124, 0x1C770000}, > + {0x4e300160, 0x00009102}, > + {0x4e30016C, 0x35F00000}, > + {0x4e300170, 0x8B0B0608}, > + {0x4e300250, 0x00000028}, > + {0x4e300254, 0x00FE00FE}, > + {0x4e300258, 0x00000008}, > + {0x4e30025C, 0x00000400}, > + {0x4e300300, 0x224F2215}, > + {0x4e300304, 0x00FE2213}, > + {0x4e300308, 0x0A3C0E3C}, > + }, > + { > + {0x01, 0xE4}, > + {0x02, 0x36}, > + {0x03, 0xF2}, > + {0x0b, 0x46}, > + {0x0c, 0x11}, > + {0x0e, 0x11}, > + {0x16, 0x04}, > + }, > + 0, > + }, > + > +}; > + > +/* PHY Initialize Configuration */ > +static struct dram_cfg_param ddr_ddrphy_cfg[] = { > + {0x100a0, 0x0}, > + {0x100a1, 0x1}, > + {0x100a2, 0x2}, > + {0x100a3, 0x3}, > + {0x100a4, 0x4}, > + {0x100a5, 0x5}, > + {0x100a6, 0x6}, > + {0x100a7, 0x7}, > + {0x110a0, 0x0}, > + {0x110a1, 0x1}, > + {0x110a2, 0x2}, > + {0x110a3, 0x3}, > + {0x110a4, 0x4}, > + {0x110a5, 0x5}, > + {0x110a6, 0x6}, > + {0x110a7, 0x7}, > + {0x1005f, 0x5ff}, > + {0x1015f, 0x5ff}, > + {0x1105f, 0x5ff}, > + {0x1115f, 0x5ff}, > + {0x55, 0x1ff}, > + {0x1055, 0x1ff}, > + {0x2055, 0x1ff}, > + {0x200c5, 0x19}, > + {0x2002e, 0x2}, > + {0x90204, 0x0}, > + {0x20024, 0x1e3}, > + {0x2003a, 0x2}, > + {0x2007d, 0x212}, > + {0x2007c, 0x61}, > + {0x20056, 0x3}, > + {0x1004d, 0x600}, > + {0x1014d, 0x600}, > + {0x1104d, 0x600}, > + {0x1114d, 0x600}, > + {0x10049, 0xe00}, > + {0x10149, 0xe00}, > + {0x11049, 0xe00}, > + {0x11149, 0xe00}, > + {0x43, 0x60}, > + {0x1043, 0x60}, > + {0x2043, 0x60}, > + {0x20018, 0x1}, > + {0x20075, 0x4}, > + {0x20050, 0x0}, > + {0x2009b, 0x2}, > + {0x20008, 0x3a5}, > + {0x20088, 0x9}, > + {0x200b2, 0x10c}, > + {0x10043, 0x5a1}, > + {0x10143, 0x5a1}, > + {0x11043, 0x5a1}, > + {0x11143, 0x5a1}, > + {0x200fa, 0x2}, > + {0x20019, 0x1}, > + {0x200f0, 0x600}, > + {0x200f1, 0x0}, > + {0x200f2, 0x4444}, > + {0x200f3, 0x8888}, > + {0x200f4, 0x5655}, > + {0x200f5, 0x0}, > + {0x200f6, 0x0}, > + {0x200f7, 0xf000}, > + {0x20025, 0x0}, > + {0x2002d, 0x1}, > + {0x2002c, 0x0}, > + {0x20021, 0x0}, > + {0x200c7, 0x21}, > + {0x1200c7, 0x21}, > + {0x200ca, 0x24}, > + {0x1200ca, 0x24}, > + > +}; > + > +/* ddr phy trained csr */ > +static struct dram_cfg_param ddr_ddrphy_trained_csr[] = { > + {0x1005f, 0x0}, > + {0x1015f, 0x0}, > + {0x1105f, 0x0}, > + {0x1115f, 0x0}, > + {0x55, 0x0}, > + {0x1055, 0x0}, > + {0x2055, 0x0}, > + {0x200c5, 0x0}, > + {0x2002e, 0x0}, > + {0x90204, 0x0}, > + {0x20024, 0x0}, > + {0x2003a, 0x0}, > + {0x2007d, 0x0}, > + {0x2007c, 0x0}, > + {0x20056, 0x0}, > + {0x1004d, 0x0}, > + {0x1014d, 0x0}, > + {0x1104d, 0x0}, > + {0x1114d, 0x0}, > + {0x10049, 0x0}, > + {0x10149, 0x0}, > + {0x11049, 0x0}, > + {0x11149, 0x0}, > + {0x43, 0x0}, > + {0x1043, 0x0}, > + {0x2043, 0x0}, > + {0x20018, 0x0}, > + {0x20075, 0x0}, > + {0x20050, 0x0}, > + {0x2009b, 0x0}, > + {0x20008, 0x0}, > + {0x20088, 0x0}, > + {0x200b2, 0x0}, > + {0x10043, 0x0}, > + {0x10143, 0x0}, > + {0x11043, 0x0}, > + {0x11143, 0x0}, > + {0x200fa, 0x0}, > + {0x20019, 0x0}, > + {0x200f0, 0x0}, > + {0x200f1, 0x0}, > + {0x200f2, 0x0}, > + {0x200f3, 0x0}, > + {0x200f4, 0x0}, > + {0x200f5, 0x0}, > + {0x200f6, 0x0}, > + {0x200f7, 0x0}, > + {0x20025, 0x0}, > + {0x2002d, 0x0}, > + {0x2002c, 0x0}, > + {0xd0000, 0x0}, > + {0x90000, 0x0}, > + {0x90001, 0x0}, > + {0x90002, 0x0}, > + {0x90003, 0x0}, > + {0x90004, 0x0}, > + {0x90005, 0x0}, > + {0x90029, 0x0}, > + {0x9002a, 0x0}, > + {0x9002b, 0x0}, > + {0x9002c, 0x0}, > + {0x9002d, 0x0}, > + {0x9002e, 0x0}, > + {0x9002f, 0x0}, > + {0x90030, 0x0}, > + {0x90031, 0x0}, > + {0x90032, 0x0}, > + {0x90033, 0x0}, > + {0x90034, 0x0}, > + {0x90035, 0x0}, > + {0x90036, 0x0}, > + {0x90037, 0x0}, > + {0x90038, 0x0}, > + {0x90039, 0x0}, > + {0x9003a, 0x0}, > + {0x9003b, 0x0}, > + {0x9003c, 0x0}, > + {0x9003d, 0x0}, > + {0x9003e, 0x0}, > + {0x9003f, 0x0}, > + {0x90040, 0x0}, > + {0x90041, 0x0}, > + {0x90042, 0x0}, > + {0x90043, 0x0}, > + {0x90044, 0x0}, > + {0x90045, 0x0}, > + {0x90046, 0x0}, > + {0x90047, 0x0}, > + {0x90048, 0x0}, > + {0x90049, 0x0}, > + {0x9004a, 0x0}, > + {0x9004b, 0x0}, > + {0x9004c, 0x0}, > + {0x9004d, 0x0}, > + {0x9004e, 0x0}, > + {0x9004f, 0x0}, > + {0x90050, 0x0}, > + {0x90051, 0x0}, > + {0x90052, 0x0}, > + {0x90053, 0x0}, > + {0x90054, 0x0}, > + {0x90055, 0x0}, > + {0x90056, 0x0}, > + {0x90057, 0x0}, > + {0x90058, 0x0}, > + {0x90059, 0x0}, > + {0x9005a, 0x0}, > + {0x9005b, 0x0}, > + {0x9005c, 0x0}, > + {0x9005d, 0x0}, > + {0x9005e, 0x0}, > + {0x9005f, 0x0}, > + {0x90060, 0x0}, > + {0x90061, 0x0}, > + {0x90062, 0x0}, > + {0x90063, 0x0}, > + {0x90064, 0x0}, > + {0x90065, 0x0}, > + {0x90066, 0x0}, > + {0x90067, 0x0}, > + {0x90068, 0x0}, > + {0x90069, 0x0}, > + {0x9006a, 0x0}, > + {0x9006b, 0x0}, > + {0x9006c, 0x0}, > + {0x9006d, 0x0}, > + {0x9006e, 0x0}, > + {0x9006f, 0x0}, > + {0x90070, 0x0}, > + {0x90071, 0x0}, > + {0x90072, 0x0}, > + {0x90073, 0x0}, > + {0x90074, 0x0}, > + {0x90075, 0x0}, > + {0x90076, 0x0}, > + {0x90077, 0x0}, > + {0x90078, 0x0}, > + {0x90079, 0x0}, > + {0x9007a, 0x0}, > + {0x9007b, 0x0}, > + {0x9007c, 0x0}, > + {0x9007d, 0x0}, > + {0x9007e, 0x0}, > + {0x9007f, 0x0}, > + {0x90080, 0x0}, > + {0x90081, 0x0}, > + {0x90082, 0x0}, > + {0x90083, 0x0}, > + {0x90084, 0x0}, > + {0x90085, 0x0}, > + {0x90086, 0x0}, > + {0x90087, 0x0}, > + {0x90088, 0x0}, > + {0x90089, 0x0}, > + {0x9008a, 0x0}, > + {0x9008b, 0x0}, > + {0x9008c, 0x0}, > + {0x9008d, 0x0}, > + {0x9008e, 0x0}, > + {0x9008f, 0x0}, > + {0x90090, 0x0}, > + {0x90091, 0x0}, > + {0x90092, 0x0}, > + {0x90093, 0x0}, > + {0x90094, 0x0}, > + {0x90095, 0x0}, > + {0x90096, 0x0}, > + {0x90097, 0x0}, > + {0x90098, 0x0}, > + {0x90099, 0x0}, > + {0x9009a, 0x0}, > + {0x9009b, 0x0}, > + {0x9009c, 0x0}, > + {0x9009d, 0x0}, > + {0x9009e, 0x0}, > + {0x9009f, 0x0}, > + {0x900a0, 0x0}, > + {0x900a1, 0x0}, > + {0x900a2, 0x0}, > + {0x900a3, 0x0}, > + {0x900a4, 0x0}, > + {0x900a5, 0x0}, > + {0x900a6, 0x0}, > + {0x900a7, 0x0}, > + {0x900a8, 0x0}, > + {0x900a9, 0x0}, > + {0x40000, 0x0}, > + {0x40020, 0x0}, > + {0x40040, 0x0}, > + {0x40060, 0x0}, > + {0x40001, 0x0}, > + {0x40021, 0x0}, > + {0x40041, 0x0}, > + {0x40061, 0x0}, > + {0x40002, 0x0}, > + {0x40022, 0x0}, > + {0x40042, 0x0}, > + {0x40062, 0x0}, > + {0x40003, 0x0}, > + {0x40023, 0x0}, > + {0x40043, 0x0}, > + {0x40063, 0x0}, > + {0x40004, 0x0}, > + {0x40024, 0x0}, > + {0x40044, 0x0}, > + {0x40064, 0x0}, > + {0x40005, 0x0}, > + {0x40025, 0x0}, > + {0x40045, 0x0}, > + {0x40065, 0x0}, > + {0x40006, 0x0}, > + {0x40026, 0x0}, > + {0x40046, 0x0}, > + {0x40066, 0x0}, > + {0x40007, 0x0}, > + {0x40027, 0x0}, > + {0x40047, 0x0}, > + {0x40067, 0x0}, > + {0x40008, 0x0}, > + {0x40028, 0x0}, > + {0x40048, 0x0}, > + {0x40068, 0x0}, > + {0x40009, 0x0}, > + {0x40029, 0x0}, > + {0x40049, 0x0}, > + {0x40069, 0x0}, > + {0x4000a, 0x0}, > + {0x4002a, 0x0}, > + {0x4004a, 0x0}, > + {0x4006a, 0x0}, > + {0x4000b, 0x0}, > + {0x4002b, 0x0}, > + {0x4004b, 0x0}, > + {0x4006b, 0x0}, > + {0x4000c, 0x0}, > + {0x4002c, 0x0}, > + {0x4004c, 0x0}, > + {0x4006c, 0x0}, > + {0x4000d, 0x0}, > + {0x4002d, 0x0}, > + {0x4004d, 0x0}, > + {0x4006d, 0x0}, > + {0x4000e, 0x0}, > + {0x4002e, 0x0}, > + {0x4004e, 0x0}, > + {0x4006e, 0x0}, > + {0x4000f, 0x0}, > + {0x4002f, 0x0}, > + {0x4004f, 0x0}, > + {0x4006f, 0x0}, > + {0x40010, 0x0}, > + {0x40030, 0x0}, > + {0x40050, 0x0}, > + {0x40070, 0x0}, > + {0x40011, 0x0}, > + {0x40031, 0x0}, > + {0x40051, 0x0}, > + {0x40071, 0x0}, > + {0x40012, 0x0}, > + {0x40032, 0x0}, > + {0x40052, 0x0}, > + {0x40072, 0x0}, > + {0x40013, 0x0}, > + {0x40033, 0x0}, > + {0x40053, 0x0}, > + {0x40073, 0x0}, > + {0x40014, 0x0}, > + {0x40034, 0x0}, > + {0x40054, 0x0}, > + {0x40074, 0x0}, > + {0x40015, 0x0}, > + {0x40035, 0x0}, > + {0x40055, 0x0}, > + {0x40075, 0x0}, > + {0x40016, 0x0}, > + {0x40036, 0x0}, > + {0x40056, 0x0}, > + {0x40076, 0x0}, > + {0x40017, 0x0}, > + {0x40037, 0x0}, > + {0x40057, 0x0}, > + {0x40077, 0x0}, > + {0x40018, 0x0}, > + {0x40038, 0x0}, > + {0x40058, 0x0}, > + {0x40078, 0x0}, > + {0x40019, 0x0}, > + {0x40039, 0x0}, > + {0x40059, 0x0}, > + {0x40079, 0x0}, > + {0x4001a, 0x0}, > + {0x4003a, 0x0}, > + {0x4005a, 0x0}, > + {0x4007a, 0x0}, > + {0x900aa, 0x0}, > + {0x900ab, 0x0}, > + {0x900ac, 0x0}, > + {0x900ad, 0x0}, > + {0x900ae, 0x0}, > + {0x900af, 0x0}, > + {0x900b0, 0x0}, > + {0x900b1, 0x0}, > + {0x900b2, 0x0}, > + {0x900b3, 0x0}, > + {0x900b4, 0x0}, > + {0x900b5, 0x0}, > + {0x900b6, 0x0}, > + {0x900b7, 0x0}, > + {0x900b8, 0x0}, > + {0x900b9, 0x0}, > + {0x900ba, 0x0}, > + {0x900bb, 0x0}, > + {0x900bc, 0x0}, > + {0x900bd, 0x0}, > + {0x900be, 0x0}, > + {0x900bf, 0x0}, > + {0x900c0, 0x0}, > + {0x900c1, 0x0}, > + {0x900c2, 0x0}, > + {0x900c3, 0x0}, > + {0x900c4, 0x0}, > + {0x900c5, 0x0}, > + {0x900c6, 0x0}, > + {0x900c7, 0x0}, > + {0x900c8, 0x0}, > + {0x900c9, 0x0}, > + {0x900ca, 0x0}, > + {0x900cb, 0x0}, > + {0x900cc, 0x0}, > + {0x900cd, 0x0}, > + {0x900ce, 0x0}, > + {0x900cf, 0x0}, > + {0x900d0, 0x0}, > + {0x900d1, 0x0}, > + {0x900d2, 0x0}, > + {0x900d3, 0x0}, > + {0x900d4, 0x0}, > + {0x900d5, 0x0}, > + {0x900d6, 0x0}, > + {0x900d7, 0x0}, > + {0x900d8, 0x0}, > + {0x900d9, 0x0}, > + {0x900da, 0x0}, > + {0x900db, 0x0}, > + {0x900dc, 0x0}, > + {0x900dd, 0x0}, > + {0x900de, 0x0}, > + {0x900df, 0x0}, > + {0x900e0, 0x0}, > + {0x900e1, 0x0}, > + {0x900e2, 0x0}, > + {0x900e3, 0x0}, > + {0x900e4, 0x0}, > + {0x900e5, 0x0}, > + {0x900e6, 0x0}, > + {0x900e7, 0x0}, > + {0x900e8, 0x0}, > + {0x900e9, 0x0}, > + {0x900ea, 0x0}, > + {0x900eb, 0x0}, > + {0x900ec, 0x0}, > + {0x900ed, 0x0}, > + {0x900ee, 0x0}, > + {0x900ef, 0x0}, > + {0x900f0, 0x0}, > + {0x900f1, 0x0}, > + {0x900f2, 0x0}, > + {0x900f3, 0x0}, > + {0x900f4, 0x0}, > + {0x900f5, 0x0}, > + {0x900f6, 0x0}, > + {0x900f7, 0x0}, > + {0x900f8, 0x0}, > + {0x900f9, 0x0}, > + {0x900fa, 0x0}, > + {0x900fb, 0x0}, > + {0x900fc, 0x0}, > + {0x900fd, 0x0}, > + {0x900fe, 0x0}, > + {0x900ff, 0x0}, > + {0x90100, 0x0}, > + {0x90101, 0x0}, > + {0x90102, 0x0}, > + {0x90103, 0x0}, > + {0x90104, 0x0}, > + {0x90105, 0x0}, > + {0x90106, 0x0}, > + {0x90107, 0x0}, > + {0x90108, 0x0}, > + {0x90109, 0x0}, > + {0x9010a, 0x0}, > + {0x9010b, 0x0}, > + {0x9010c, 0x0}, > + {0x9010d, 0x0}, > + {0x9010e, 0x0}, > + {0x9010f, 0x0}, > + {0x90110, 0x0}, > + {0x90111, 0x0}, > + {0x90112, 0x0}, > + {0x90113, 0x0}, > + {0x90114, 0x0}, > + {0x90115, 0x0}, > + {0x90116, 0x0}, > + {0x90117, 0x0}, > + {0x90118, 0x0}, > + {0x90119, 0x0}, > + {0x9011a, 0x0}, > + {0x9011b, 0x0}, > + {0x9011c, 0x0}, > + {0x9011d, 0x0}, > + {0x9011e, 0x0}, > + {0x9011f, 0x0}, > + {0x90120, 0x0}, > + {0x90121, 0x0}, > + {0x90122, 0x0}, > + {0x90123, 0x0}, > + {0x90124, 0x0}, > + {0x90125, 0x0}, > + {0x90126, 0x0}, > + {0x90127, 0x0}, > + {0x90128, 0x0}, > + {0x90129, 0x0}, > + {0x9012a, 0x0}, > + {0x9012b, 0x0}, > + {0x9012c, 0x0}, > + {0x9012d, 0x0}, > + {0x9012e, 0x0}, > + {0x9012f, 0x0}, > + {0x90130, 0x0}, > + {0x90131, 0x0}, > + {0x90132, 0x0}, > + {0x90133, 0x0}, > + {0x90134, 0x0}, > + {0x90135, 0x0}, > + {0x90136, 0x0}, > + {0x90137, 0x0}, > + {0x90138, 0x0}, > + {0x90139, 0x0}, > + {0x9013a, 0x0}, > + {0x9013b, 0x0}, > + {0x9013c, 0x0}, > + {0x9013d, 0x0}, > + {0x9013e, 0x0}, > + {0x9013f, 0x0}, > + {0x90140, 0x0}, > + {0x90141, 0x0}, > + {0x90142, 0x0}, > + {0x90143, 0x0}, > + {0x90144, 0x0}, > + {0x90145, 0x0}, > + {0x90146, 0x0}, > + {0x90147, 0x0}, > + {0x90148, 0x0}, > + {0x90149, 0x0}, > + {0x9014a, 0x0}, > + {0x9014b, 0x0}, > + {0x9014c, 0x0}, > + {0x9014d, 0x0}, > + {0x9014e, 0x0}, > + {0x9014f, 0x0}, > + {0x90150, 0x0}, > + {0x90151, 0x0}, > + {0x90152, 0x0}, > + {0x90153, 0x0}, > + {0x90154, 0x0}, > + {0x90155, 0x0}, > + {0x90156, 0x0}, > + {0x90157, 0x0}, > + {0x90158, 0x0}, > + {0x90159, 0x0}, > + {0x9015a, 0x0}, > + {0x9015b, 0x0}, > + {0x9015c, 0x0}, > + {0x9015d, 0x0}, > + {0x9015e, 0x0}, > + {0x9015f, 0x0}, > + {0x90160, 0x0}, > + {0x90161, 0x0}, > + {0x90162, 0x0}, > + {0x90163, 0x0}, > + {0x90164, 0x0}, > + {0x90165, 0x0}, > + {0x90166, 0x0}, > + {0x90167, 0x0}, > + {0x90168, 0x0}, > + {0x90169, 0x0}, > + {0x9016a, 0x0}, > + {0x9016b, 0x0}, > + {0x9016c, 0x0}, > + {0x9016d, 0x0}, > + {0x9016e, 0x0}, > + {0x9016f, 0x0}, > + {0x90170, 0x0}, > + {0x90171, 0x0}, > + {0x90172, 0x0}, > + {0x90173, 0x0}, > + {0x90174, 0x0}, > + {0x90175, 0x0}, > + {0x90176, 0x0}, > + {0x90177, 0x0}, > + {0x90178, 0x0}, > + {0x90179, 0x0}, > + {0x9017a, 0x0}, > + {0x9017b, 0x0}, > + {0x9017c, 0x0}, > + {0x9017d, 0x0}, > + {0x9017e, 0x0}, > + {0x9017f, 0x0}, > + {0x90180, 0x0}, > + {0x90181, 0x0}, > + {0x90182, 0x0}, > + {0x90183, 0x0}, > + {0x90184, 0x0}, > + {0x90006, 0x0}, > + {0x90007, 0x0}, > + {0x90008, 0x0}, > + {0x90009, 0x0}, > + {0x9000a, 0x0}, > + {0x9000b, 0x0}, > + {0xd00e7, 0x0}, > + {0x90017, 0x0}, > + {0x9001f, 0x0}, > + {0x90026, 0x0}, > + {0x400d0, 0x0}, > + {0x400d1, 0x0}, > + {0x400d2, 0x0}, > + {0x400d3, 0x0}, > + {0x400d4, 0x0}, > + {0x400d5, 0x0}, > + {0x400d6, 0x0}, > + {0x400d7, 0x0}, > + {0x200be, 0x0}, > + {0x2000b, 0x0}, > + {0x2000c, 0x0}, > + {0x2000d, 0x0}, > + {0x2000e, 0x0}, > + {0x9000c, 0x0}, > + {0x9000d, 0x0}, > + {0x9000e, 0x0}, > + {0x9000f, 0x0}, > + {0x90010, 0x0}, > + {0x90011, 0x0}, > + {0x90012, 0x0}, > + {0x90013, 0x0}, > + {0x20010, 0x0}, > + {0x20011, 0x0}, > + {0x40080, 0x0}, > + {0x40081, 0x0}, > + {0x40082, 0x0}, > + {0x40083, 0x0}, > + {0x40084, 0x0}, > + {0x40085, 0x0}, > + {0x400fd, 0x0}, > + {0x400f1, 0x0}, > + {0x10011, 0x0}, > + {0x10012, 0x0}, > + {0x10013, 0x0}, > + {0x10018, 0x0}, > + {0x10002, 0x0}, > + {0x100b2, 0x0}, > + {0x101b4, 0x0}, > + {0x102b4, 0x0}, > + {0x103b4, 0x0}, > + {0x104b4, 0x0}, > + {0x105b4, 0x0}, > + {0x106b4, 0x0}, > + {0x107b4, 0x0}, > + {0x108b4, 0x0}, > + {0x11011, 0x0}, > + {0x11012, 0x0}, > + {0x11013, 0x0}, > + {0x11018, 0x0}, > + {0x11002, 0x0}, > + {0x110b2, 0x0}, > + {0x111b4, 0x0}, > + {0x112b4, 0x0}, > + {0x113b4, 0x0}, > + {0x114b4, 0x0}, > + {0x115b4, 0x0}, > + {0x116b4, 0x0}, > + {0x117b4, 0x0}, > + {0x118b4, 0x0}, > + {0x20089, 0x0}, > + {0xc0080, 0x0}, > + {0x200cb, 0x0}, > + {0x10068, 0x0}, > + {0x10069, 0x0}, > + {0x10168, 0x0}, > + {0x10169, 0x0}, > + {0x10268, 0x0}, > + {0x10269, 0x0}, > + {0x10368, 0x0}, > + {0x10369, 0x0}, > + {0x10468, 0x0}, > + {0x10469, 0x0}, > + {0x10568, 0x0}, > + {0x10569, 0x0}, > + {0x10668, 0x0}, > + {0x10669, 0x0}, > + {0x10768, 0x0}, > + {0x10769, 0x0}, > + {0x10868, 0x0}, > + {0x10869, 0x0}, > + {0x100aa, 0x0}, > + {0x10062, 0x0}, > + {0x10001, 0x0}, > + {0x100a0, 0x0}, > + {0x100a1, 0x0}, > + {0x100a2, 0x0}, > + {0x100a3, 0x0}, > + {0x100a4, 0x0}, > + {0x100a5, 0x0}, > + {0x100a6, 0x0}, > + {0x100a7, 0x0}, > + {0x11068, 0x0}, > + {0x11069, 0x0}, > + {0x11168, 0x0}, > + {0x11169, 0x0}, > + {0x11268, 0x0}, > + {0x11269, 0x0}, > + {0x11368, 0x0}, > + {0x11369, 0x0}, > + {0x11468, 0x0}, > + {0x11469, 0x0}, > + {0x11568, 0x0}, > + {0x11569, 0x0}, > + {0x11668, 0x0}, > + {0x11669, 0x0}, > + {0x11768, 0x0}, > + {0x11769, 0x0}, > + {0x11868, 0x0}, > + {0x11869, 0x0}, > + {0x110aa, 0x0}, > + {0x11062, 0x0}, > + {0x11001, 0x0}, > + {0x110a0, 0x0}, > + {0x110a1, 0x0}, > + {0x110a2, 0x0}, > + {0x110a3, 0x0}, > + {0x110a4, 0x0}, > + {0x110a5, 0x0}, > + {0x110a6, 0x0}, > + {0x110a7, 0x0}, > + {0x80, 0x0}, > + {0x1080, 0x0}, > + {0x2080, 0x0}, > + {0x10020, 0x0}, > + {0x10080, 0x0}, > + {0x10081, 0x0}, > + {0x100d0, 0x0}, > + {0x100d1, 0x0}, > + {0x1008c, 0x0}, > + {0x1008d, 0x0}, > + {0x10180, 0x0}, > + {0x10181, 0x0}, > + {0x101d0, 0x0}, > + {0x101d1, 0x0}, > + {0x1018c, 0x0}, > + {0x1018d, 0x0}, > + {0x100c0, 0x0}, > + {0x100c1, 0x0}, > + {0x101c0, 0x0}, > + {0x101c1, 0x0}, > + {0x102c0, 0x0}, > + {0x102c1, 0x0}, > + {0x103c0, 0x0}, > + {0x103c1, 0x0}, > + {0x104c0, 0x0}, > + {0x104c1, 0x0}, > + {0x105c0, 0x0}, > + {0x105c1, 0x0}, > + {0x106c0, 0x0}, > + {0x106c1, 0x0}, > + {0x107c0, 0x0}, > + {0x107c1, 0x0}, > + {0x108c0, 0x0}, > + {0x108c1, 0x0}, > + {0x100ae, 0x0}, > + {0x100af, 0x0}, > + {0x11020, 0x0}, > + {0x11080, 0x0}, > + {0x11081, 0x0}, > + {0x110d0, 0x0}, > + {0x110d1, 0x0}, > + {0x1108c, 0x0}, > + {0x1108d, 0x0}, > + {0x11180, 0x0}, > + {0x11181, 0x0}, > + {0x111d0, 0x0}, > + {0x111d1, 0x0}, > + {0x1118c, 0x0}, > + {0x1118d, 0x0}, > + {0x110c0, 0x0}, > + {0x110c1, 0x0}, > + {0x111c0, 0x0}, > + {0x111c1, 0x0}, > + {0x112c0, 0x0}, > + {0x112c1, 0x0}, > + {0x113c0, 0x0}, > + {0x113c1, 0x0}, > + {0x114c0, 0x0}, > + {0x114c1, 0x0}, > + {0x115c0, 0x0}, > + {0x115c1, 0x0}, > + {0x116c0, 0x0}, > + {0x116c1, 0x0}, > + {0x117c0, 0x0}, > + {0x117c1, 0x0}, > + {0x118c0, 0x0}, > + {0x118c1, 0x0}, > + {0x110ae, 0x0}, > + {0x110af, 0x0}, > + {0x90201, 0x0}, > + {0x90202, 0x0}, > + {0x90203, 0x0}, > + {0x90205, 0x0}, > + {0x90206, 0x0}, > + {0x90207, 0x0}, > + {0x90208, 0x0}, > + {0x20020, 0x0}, > + {0x20077, 0x0}, > + {0x20072, 0x0}, > + {0x20073, 0x0}, > + {0x400c0, 0x0}, > + {0x10040, 0x0}, > + {0x10140, 0x0}, > + {0x10240, 0x0}, > + {0x10340, 0x0}, > + {0x10440, 0x0}, > + {0x10540, 0x0}, > + {0x10640, 0x0}, > + {0x10740, 0x0}, > + {0x10840, 0x0}, > + {0x11040, 0x0}, > + {0x11140, 0x0}, > + {0x11240, 0x0}, > + {0x11340, 0x0}, > + {0x11440, 0x0}, > + {0x11540, 0x0}, > + {0x11640, 0x0}, > + {0x11740, 0x0}, > + {0x11840, 0x0}, > + > +}; > + > +/* P0 message block parameter for training firmware */ > +static struct dram_cfg_param ddr_fsp0_cfg[] = { > + {0xd0000, 0x0}, > + {0x54003, 0xe94}, > + {0x54004, 0x4}, > + {0x54006, 0x15}, > + {0x54008, 0x131f}, > + {0x54009, 0xc8}, > + {0x5400b, 0x4}, > + {0x5400d, 0x100}, > + {0x5400f, 0x100}, > + {0x54012, 0x110}, > + {0x54019, 0x36e4}, > + {0x5401a, 0xf2}, > + {0x5401b, 0x1146}, > + {0x5401c, 0x1108}, > + {0x5401e, 0x4}, > + {0x5401f, 0x36e4}, > + {0x54020, 0xf2}, > + {0x54021, 0x1146}, > + {0x54022, 0x1108}, > + {0x54024, 0x4}, > + {0x54032, 0xe400}, > + {0x54033, 0xf236}, > + {0x54034, 0x4600}, > + {0x54035, 0x811}, > + {0x54036, 0x11}, > + {0x54037, 0x400}, > + {0x54038, 0xe400}, > + {0x54039, 0xf236}, > + {0x5403a, 0x4600}, > + {0x5403b, 0x811}, > + {0x5403c, 0x11}, > + {0x5403d, 0x400}, > + {0xd0000, 0x1} > +}; > + > +/* P0 2D message block parameter for training firmware */ > +static struct dram_cfg_param ddr_fsp0_2d_cfg[] = { > + {0xd0000, 0x0}, > + {0x54003, 0xe94}, > + {0x54004, 0x4}, > + {0x54006, 0x15}, > + {0x54008, 0x61}, > + {0x54009, 0xc8}, > + {0x5400b, 0x4}, > + {0x5400d, 0x100}, > + {0x5400f, 0x100}, > + {0x54010, 0x2080}, > + {0x54012, 0x110}, > + {0x54019, 0x36e4}, > + {0x5401a, 0xf2}, > + {0x5401b, 0x1146}, > + {0x5401c, 0x1108}, > + {0x5401e, 0x4}, > + {0x5401f, 0x36e4}, > + {0x54020, 0xf2}, > + {0x54021, 0x1146}, > + {0x54022, 0x1108}, > + {0x54024, 0x4}, > + {0x54032, 0xe400}, > + {0x54033, 0xf236}, > + {0x54034, 0x4600}, > + {0x54035, 0x811}, > + {0x54036, 0x11}, > + {0x54037, 0x400}, > + {0x54038, 0xe400}, > + {0x54039, 0xf236}, > + {0x5403a, 0x4600}, > + {0x5403b, 0x811}, > + {0x5403c, 0x11}, > + {0x5403d, 0x400}, > + {0xd0000, 0x1} > +}; > + > +/* DRAM PHY init engine image */ > +static struct dram_cfg_param ddr_phy_pie[] = { > + {0xd0000, 0x0}, > + {0x90000, 0x10}, > + {0x90001, 0x400}, > + {0x90002, 0x10e}, > + {0x90003, 0x0}, > + {0x90004, 0x0}, > + {0x90005, 0x8}, > + {0x90029, 0xb}, > + {0x9002a, 0x480}, > + {0x9002b, 0x109}, > + {0x9002c, 0x8}, > + {0x9002d, 0x448}, > + {0x9002e, 0x139}, > + {0x9002f, 0x8}, > + {0x90030, 0x478}, > + {0x90031, 0x109}, > + {0x90032, 0x0}, > + {0x90033, 0xe8}, > + {0x90034, 0x109}, > + {0x90035, 0x2}, > + {0x90036, 0x10}, > + {0x90037, 0x139}, > + {0x90038, 0xb}, > + {0x90039, 0x7c0}, > + {0x9003a, 0x139}, > + {0x9003b, 0x44}, > + {0x9003c, 0x633}, > + {0x9003d, 0x159}, > + {0x9003e, 0x14f}, > + {0x9003f, 0x630}, > + {0x90040, 0x159}, > + {0x90041, 0x47}, > + {0x90042, 0x633}, > + {0x90043, 0x149}, > + {0x90044, 0x4f}, > + {0x90045, 0x633}, > + {0x90046, 0x179}, > + {0x90047, 0x8}, > + {0x90048, 0xe0}, > + {0x90049, 0x109}, > + {0x9004a, 0x0}, > + {0x9004b, 0x7c8}, > + {0x9004c, 0x109}, > + {0x9004d, 0x0}, > + {0x9004e, 0x1}, > + {0x9004f, 0x8}, > + {0x90050, 0x30}, > + {0x90051, 0x65a}, > + {0x90052, 0x9}, > + {0x90053, 0x0}, > + {0x90054, 0x45a}, > + {0x90055, 0x9}, > + {0x90056, 0x0}, > + {0x90057, 0x448}, > + {0x90058, 0x109}, > + {0x90059, 0x40}, > + {0x9005a, 0x633}, > + {0x9005b, 0x179}, > + {0x9005c, 0x1}, > + {0x9005d, 0x618}, > + {0x9005e, 0x109}, > + {0x9005f, 0x40c0}, > + {0x90060, 0x633}, > + {0x90061, 0x149}, > + {0x90062, 0x8}, > + {0x90063, 0x4}, > + {0x90064, 0x48}, > + {0x90065, 0x4040}, > + {0x90066, 0x633}, > + {0x90067, 0x149}, > + {0x90068, 0x0}, > + {0x90069, 0x4}, > + {0x9006a, 0x48}, > + {0x9006b, 0x40}, > + {0x9006c, 0x633}, > + {0x9006d, 0x149}, > + {0x9006e, 0x0}, > + {0x9006f, 0x658}, > + {0x90070, 0x109}, > + {0x90071, 0x10}, > + {0x90072, 0x4}, > + {0x90073, 0x18}, > + {0x90074, 0x0}, > + {0x90075, 0x4}, > + {0x90076, 0x78}, > + {0x90077, 0x549}, > + {0x90078, 0x633}, > + {0x90079, 0x159}, > + {0x9007a, 0xd49}, > + {0x9007b, 0x633}, > + {0x9007c, 0x159}, > + {0x9007d, 0x94a}, > + {0x9007e, 0x633}, > + {0x9007f, 0x159}, > + {0x90080, 0x441}, > + {0x90081, 0x633}, > + {0x90082, 0x149}, > + {0x90083, 0x42}, > + {0x90084, 0x633}, > + {0x90085, 0x149}, > + {0x90086, 0x1}, > + {0x90087, 0x633}, > + {0x90088, 0x149}, > + {0x90089, 0x0}, > + {0x9008a, 0xe0}, > + {0x9008b, 0x109}, > + {0x9008c, 0xa}, > + {0x9008d, 0x10}, > + {0x9008e, 0x109}, > + {0x9008f, 0x9}, > + {0x90090, 0x3c0}, > + {0x90091, 0x149}, > + {0x90092, 0x9}, > + {0x90093, 0x3c0}, > + {0x90094, 0x159}, > + {0x90095, 0x18}, > + {0x90096, 0x10}, > + {0x90097, 0x109}, > + {0x90098, 0x0}, > + {0x90099, 0x3c0}, > + {0x9009a, 0x109}, > + {0x9009b, 0x18}, > + {0x9009c, 0x4}, > + {0x9009d, 0x48}, > + {0x9009e, 0x18}, > + {0x9009f, 0x4}, > + {0x900a0, 0x58}, > + {0x900a1, 0xb}, > + {0x900a2, 0x10}, > + {0x900a3, 0x109}, > + {0x900a4, 0x1}, > + {0x900a5, 0x10}, > + {0x900a6, 0x109}, > + {0x900a7, 0x5}, > + {0x900a8, 0x7c0}, > + {0x900a9, 0x109}, > + {0x40000, 0x811}, > + {0x40020, 0x880}, > + {0x40040, 0x0}, > + {0x40060, 0x0}, > + {0x40001, 0x4008}, > + {0x40021, 0x83}, > + {0x40041, 0x4f}, > + {0x40061, 0x0}, > + {0x40002, 0x4040}, > + {0x40022, 0x83}, > + {0x40042, 0x51}, > + {0x40062, 0x0}, > + {0x40003, 0x811}, > + {0x40023, 0x880}, > + {0x40043, 0x0}, > + {0x40063, 0x0}, > + {0x40004, 0x720}, > + {0x40024, 0xf}, > + {0x40044, 0x1740}, > + {0x40064, 0x0}, > + {0x40005, 0x16}, > + {0x40025, 0x83}, > + {0x40045, 0x4b}, > + {0x40065, 0x0}, > + {0x40006, 0x716}, > + {0x40026, 0xf}, > + {0x40046, 0x2001}, > + {0x40066, 0x0}, > + {0x40007, 0x716}, > + {0x40027, 0xf}, > + {0x40047, 0x2800}, > + {0x40067, 0x0}, > + {0x40008, 0x716}, > + {0x40028, 0xf}, > + {0x40048, 0xf00}, > + {0x40068, 0x0}, > + {0x40009, 0x720}, > + {0x40029, 0xf}, > + {0x40049, 0x1400}, > + {0x40069, 0x0}, > + {0x4000a, 0xe08}, > + {0x4002a, 0xc15}, > + {0x4004a, 0x0}, > + {0x4006a, 0x0}, > + {0x4000b, 0x625}, > + {0x4002b, 0x15}, > + {0x4004b, 0x0}, > + {0x4006b, 0x0}, > + {0x4000c, 0x4028}, > + {0x4002c, 0x80}, > + {0x4004c, 0x0}, > + {0x4006c, 0x0}, > + {0x4000d, 0xe08}, > + {0x4002d, 0xc1a}, > + {0x4004d, 0x0}, > + {0x4006d, 0x0}, > + {0x4000e, 0x625}, > + {0x4002e, 0x1a}, > + {0x4004e, 0x0}, > + {0x4006e, 0x0}, > + {0x4000f, 0x4040}, > + {0x4002f, 0x80}, > + {0x4004f, 0x0}, > + {0x4006f, 0x0}, > + {0x40010, 0x2604}, > + {0x40030, 0x15}, > + {0x40050, 0x0}, > + {0x40070, 0x0}, > + {0x40011, 0x708}, > + {0x40031, 0x5}, > + {0x40051, 0x0}, > + {0x40071, 0x2002}, > + {0x40012, 0x8}, > + {0x40032, 0x80}, > + {0x40052, 0x0}, > + {0x40072, 0x0}, > + {0x40013, 0x2604}, > + {0x40033, 0x1a}, > + {0x40053, 0x0}, > + {0x40073, 0x0}, > + {0x40014, 0x708}, > + {0x40034, 0xa}, > + {0x40054, 0x0}, > + {0x40074, 0x2002}, > + {0x40015, 0x4040}, > + {0x40035, 0x80}, > + {0x40055, 0x0}, > + {0x40075, 0x0}, > + {0x40016, 0x60a}, > + {0x40036, 0x15}, > + {0x40056, 0x1200}, > + {0x40076, 0x0}, > + {0x40017, 0x61a}, > + {0x40037, 0x15}, > + {0x40057, 0x1300}, > + {0x40077, 0x0}, > + {0x40018, 0x60a}, > + {0x40038, 0x1a}, > + {0x40058, 0x1200}, > + {0x40078, 0x0}, > + {0x40019, 0x642}, > + {0x40039, 0x1a}, > + {0x40059, 0x1300}, > + {0x40079, 0x0}, > + {0x4001a, 0x4808}, > + {0x4003a, 0x880}, > + {0x4005a, 0x0}, > + {0x4007a, 0x0}, > + {0x900aa, 0x0}, > + {0x900ab, 0x790}, > + {0x900ac, 0x11a}, > + {0x900ad, 0x8}, > + {0x900ae, 0x7aa}, > + {0x900af, 0x2a}, > + {0x900b0, 0x10}, > + {0x900b1, 0x7b2}, > + {0x900b2, 0x2a}, > + {0x900b3, 0x0}, > + {0x900b4, 0x7c8}, > + {0x900b5, 0x109}, > + {0x900b6, 0x10}, > + {0x900b7, 0x10}, > + {0x900b8, 0x109}, > + {0x900b9, 0x10}, > + {0x900ba, 0x2a8}, > + {0x900bb, 0x129}, > + {0x900bc, 0x8}, > + {0x900bd, 0x370}, > + {0x900be, 0x129}, > + {0x900bf, 0xa}, > + {0x900c0, 0x3c8}, > + {0x900c1, 0x1a9}, > + {0x900c2, 0xc}, > + {0x900c3, 0x408}, > + {0x900c4, 0x199}, > + {0x900c5, 0x14}, > + {0x900c6, 0x790}, > + {0x900c7, 0x11a}, > + {0x900c8, 0x8}, > + {0x900c9, 0x4}, > + {0x900ca, 0x18}, > + {0x900cb, 0xe}, > + {0x900cc, 0x408}, > + {0x900cd, 0x199}, > + {0x900ce, 0x8}, > + {0x900cf, 0x8568}, > + {0x900d0, 0x108}, > + {0x900d1, 0x18}, > + {0x900d2, 0x790}, > + {0x900d3, 0x16a}, > + {0x900d4, 0x8}, > + {0x900d5, 0x1d8}, > + {0x900d6, 0x169}, > + {0x900d7, 0x10}, > + {0x900d8, 0x8558}, > + {0x900d9, 0x168}, > + {0x900da, 0x1ff8}, > + {0x900db, 0x85a8}, > + {0x900dc, 0x1e8}, > + {0x900dd, 0x50}, > + {0x900de, 0x798}, > + {0x900df, 0x16a}, > + {0x900e0, 0x60}, > + {0x900e1, 0x7a0}, > + {0x900e2, 0x16a}, > + {0x900e3, 0x8}, > + {0x900e4, 0x8310}, > + {0x900e5, 0x168}, > + {0x900e6, 0x8}, > + {0x900e7, 0xa310}, > + {0x900e8, 0x168}, > + {0x900e9, 0xa}, > + {0x900ea, 0x408}, > + {0x900eb, 0x169}, > + {0x900ec, 0x6e}, > + {0x900ed, 0x0}, > + {0x900ee, 0x68}, > + {0x900ef, 0x0}, > + {0x900f0, 0x408}, > + {0x900f1, 0x169}, > + {0x900f2, 0x0}, > + {0x900f3, 0x8310}, > + {0x900f4, 0x168}, > + {0x900f5, 0x0}, > + {0x900f6, 0xa310}, > + {0x900f7, 0x168}, > + {0x900f8, 0x1ff8}, > + {0x900f9, 0x85a8}, > + {0x900fa, 0x1e8}, > + {0x900fb, 0x68}, > + {0x900fc, 0x798}, > + {0x900fd, 0x16a}, > + {0x900fe, 0x78}, > + {0x900ff, 0x7a0}, > + {0x90100, 0x16a}, > + {0x90101, 0x68}, > + {0x90102, 0x790}, > + {0x90103, 0x16a}, > + {0x90104, 0x8}, > + {0x90105, 0x8b10}, > + {0x90106, 0x168}, > + {0x90107, 0x8}, > + {0x90108, 0xab10}, > + {0x90109, 0x168}, > + {0x9010a, 0xa}, > + {0x9010b, 0x408}, > + {0x9010c, 0x169}, > + {0x9010d, 0x58}, > + {0x9010e, 0x0}, > + {0x9010f, 0x68}, > + {0x90110, 0x0}, > + {0x90111, 0x408}, > + {0x90112, 0x169}, > + {0x90113, 0x0}, > + {0x90114, 0x8b10}, > + {0x90115, 0x168}, > + {0x90116, 0x1}, > + {0x90117, 0xab10}, > + {0x90118, 0x168}, > + {0x90119, 0x0}, > + {0x9011a, 0x1d8}, > + {0x9011b, 0x169}, > + {0x9011c, 0x80}, > + {0x9011d, 0x790}, > + {0x9011e, 0x16a}, > + {0x9011f, 0x18}, > + {0x90120, 0x7aa}, > + {0x90121, 0x6a}, > + {0x90122, 0xa}, > + {0x90123, 0x0}, > + {0x90124, 0x1e9}, > + {0x90125, 0x8}, > + {0x90126, 0x8080}, > + {0x90127, 0x108}, > + {0x90128, 0xf}, > + {0x90129, 0x408}, > + {0x9012a, 0x169}, > + {0x9012b, 0xc}, > + {0x9012c, 0x0}, > + {0x9012d, 0x68}, > + {0x9012e, 0x9}, > + {0x9012f, 0x0}, > + {0x90130, 0x1a9}, > + {0x90131, 0x0}, > + {0x90132, 0x408}, > + {0x90133, 0x169}, > + {0x90134, 0x0}, > + {0x90135, 0x8080}, > + {0x90136, 0x108}, > + {0x90137, 0x8}, > + {0x90138, 0x7aa}, > + {0x90139, 0x6a}, > + {0x9013a, 0x0}, > + {0x9013b, 0x8568}, > + {0x9013c, 0x108}, > + {0x9013d, 0xb7}, > + {0x9013e, 0x790}, > + {0x9013f, 0x16a}, > + {0x90140, 0x1f}, > + {0x90141, 0x0}, > + {0x90142, 0x68}, > + {0x90143, 0x8}, > + {0x90144, 0x8558}, > + {0x90145, 0x168}, > + {0x90146, 0xf}, > + {0x90147, 0x408}, > + {0x90148, 0x169}, > + {0x90149, 0xd}, > + {0x9014a, 0x0}, > + {0x9014b, 0x68}, > + {0x9014c, 0x0}, > + {0x9014d, 0x408}, > + {0x9014e, 0x169}, > + {0x9014f, 0x0}, > + {0x90150, 0x8558}, > + {0x90151, 0x168}, > + {0x90152, 0x8}, > + {0x90153, 0x3c8}, > + {0x90154, 0x1a9}, > + {0x90155, 0x3}, > + {0x90156, 0x370}, > + {0x90157, 0x129}, > + {0x90158, 0x20}, > + {0x90159, 0x2aa}, > + {0x9015a, 0x9}, > + {0x9015b, 0x8}, > + {0x9015c, 0xe8}, > + {0x9015d, 0x109}, > + {0x9015e, 0x0}, > + {0x9015f, 0x8140}, > + {0x90160, 0x10c}, > + {0x90161, 0x10}, > + {0x90162, 0x8138}, > + {0x90163, 0x104}, > + {0x90164, 0x8}, > + {0x90165, 0x448}, > + {0x90166, 0x109}, > + {0x90167, 0xf}, > + {0x90168, 0x7c0}, > + {0x90169, 0x109}, > + {0x9016a, 0x0}, > + {0x9016b, 0xe8}, > + {0x9016c, 0x109}, > + {0x9016d, 0x47}, > + {0x9016e, 0x630}, > + {0x9016f, 0x109}, > + {0x90170, 0x8}, > + {0x90171, 0x618}, > + {0x90172, 0x109}, > + {0x90173, 0x8}, > + {0x90174, 0xe0}, > + {0x90175, 0x109}, > + {0x90176, 0x0}, > + {0x90177, 0x7c8}, > + {0x90178, 0x109}, > + {0x90179, 0x8}, > + {0x9017a, 0x8140}, > + {0x9017b, 0x10c}, > + {0x9017c, 0x0}, > + {0x9017d, 0x478}, > + {0x9017e, 0x109}, > + {0x9017f, 0x0}, > + {0x90180, 0x1}, > + {0x90181, 0x8}, > + {0x90182, 0x8}, > + {0x90183, 0x4}, > + {0x90184, 0x0}, > + {0x90006, 0x8}, > + {0x90007, 0x7c8}, > + {0x90008, 0x109}, > + {0x90009, 0x0}, > + {0x9000a, 0x400}, > + {0x9000b, 0x106}, > + {0xd00e7, 0x400}, > + {0x90017, 0x0}, > + {0x9001f, 0x2b}, > + {0x90026, 0x69}, > + {0x400d0, 0x0}, > + {0x400d1, 0x101}, > + {0x400d2, 0x105}, > + {0x400d3, 0x107}, > + {0x400d4, 0x10f}, > + {0x400d5, 0x202}, > + {0x400d6, 0x20a}, > + {0x400d7, 0x20b}, > + {0x2003a, 0x2}, > + {0x200be, 0x3}, > + {0x2000b, 0x75}, > + {0x2000c, 0xe9}, > + {0x2000d, 0x91c}, > + {0x2000e, 0x2c}, > + {0x9000c, 0x0}, > + {0x9000d, 0x173}, > + {0x9000e, 0x60}, > + {0x9000f, 0x6110}, > + {0x90010, 0x2152}, > + {0x90011, 0xdfbd}, > + {0x90012, 0x2060}, > + {0x90013, 0x6152}, > + {0x20010, 0x5a}, > + {0x20011, 0x3}, > + {0x40080, 0xe0}, > + {0x40081, 0x12}, > + {0x40082, 0xe0}, > + {0x40083, 0x12}, > + {0x40084, 0xe0}, > + {0x40085, 0x12}, > + {0x400fd, 0xf}, > + {0x400f1, 0xe}, > + {0x10011, 0x1}, > + {0x10012, 0x1}, > + {0x10013, 0x180}, > + {0x10018, 0x1}, > + {0x10002, 0x6209}, > + {0x100b2, 0x1}, > + {0x101b4, 0x1}, > + {0x102b4, 0x1}, > + {0x103b4, 0x1}, > + {0x104b4, 0x1}, > + {0x105b4, 0x1}, > + {0x106b4, 0x1}, > + {0x107b4, 0x1}, > + {0x108b4, 0x1}, > + {0x11011, 0x1}, > + {0x11012, 0x1}, > + {0x11013, 0x180}, > + {0x11018, 0x1}, > + {0x11002, 0x6209}, > + {0x110b2, 0x1}, > + {0x111b4, 0x1}, > + {0x112b4, 0x1}, > + {0x113b4, 0x1}, > + {0x114b4, 0x1}, > + {0x115b4, 0x1}, > + {0x116b4, 0x1}, > + {0x117b4, 0x1}, > + {0x118b4, 0x1}, > + {0x20089, 0x1}, > + {0x20088, 0x19}, > + {0xc0080, 0x0}, > + {0xd0000, 0x1}, > + > +}; > + > +static struct dram_fsp_msg ddr_dram_fsp_msg[] = { > + { > + /* P0 3733mts 1D */ > + .drate = 3733, > + .fw_type = FW_1D_IMAGE, > + .fsp_cfg = ddr_fsp0_cfg, > + .fsp_cfg_num = ARRAY_SIZE(ddr_fsp0_cfg), > + > + }, > + > + { > + /* P0 3733mts 2D */ > + .drate = 3733, > + .fw_type = FW_2D_IMAGE, > + .fsp_cfg = ddr_fsp0_2d_cfg, > + .fsp_cfg_num = ARRAY_SIZE(ddr_fsp0_2d_cfg), > + }, > + > +}; > + > +/* ddr timing config params */ > +struct dram_timing_info dram_timing = { > + .ddrc_cfg = ddr_ddrc_cfg, > + .ddrc_cfg_num = ARRAY_SIZE(ddr_ddrc_cfg), > + .ddrphy_cfg = ddr_ddrphy_cfg, > + .ddrphy_cfg_num = ARRAY_SIZE(ddr_ddrphy_cfg), > + .fsp_msg = ddr_dram_fsp_msg, > + .fsp_msg_num = ARRAY_SIZE(ddr_dram_fsp_msg), > + .ddrphy_trained_csr = ddr_ddrphy_trained_csr, > + .ddrphy_trained_csr_num = ARRAY_SIZE(ddr_ddrphy_trained_csr), > + .ddrphy_pie = ddr_phy_pie, > + .ddrphy_pie_num = ARRAY_SIZE(ddr_phy_pie), > + .fsp_table = { 3733, }, > + .fsp_cfg = ddr_dram_fsp_cfg, > + .fsp_cfg_num = ARRAY_SIZE(ddr_dram_fsp_cfg), > +}; > diff --git a/board/phytec/phycore_imx93/phycore-imx93.c > b/board/phytec/phycore_imx93/phycore-imx93.c > new file mode 100644 > index 00000000000..085c8e195a6 > --- /dev/null > +++ b/board/phytec/phycore_imx93/phycore-imx93.c > @@ -0,0 +1,42 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2023 PHYTEC Messtechnik GmbH > + * Author: Christoph Stoidner <c.stoidner@phytec.de> > + * Copyright (C) 2024 Mathieu Othacehe <m.othacehe@gmail.com> > + */ > + > +#include <asm/arch-imx9/ccm_regs.h> > +#include <asm/arch/sys_proto.h> > +#include <asm/arch-imx9/imx93_pins.h> > +#include <asm/arch/clock.h> > +#include <asm/global_data.h> > +#include <asm/mach-imx/boot_mode.h> > +#include <env.h> > + > +DECLARE_GLOBAL_DATA_PTR; > + > +int board_init(void) > +{ > + return 0; > +} > + > +int board_mmc_get_env_dev(int devno) > +{ > + return devno; > +} > + > +int board_late_init(void) > +{ > + switch (get_boot_device()) { > + case SD2_BOOT: > + env_set_ulong("mmcdev", 1); > + break; > + case MMC1_BOOT: > + env_set_ulong("mmcdev", 0); > + break; > + default: > + break; > + } > + > + return 0; > +} > diff --git a/board/phytec/phycore_imx93/phycore_imx93.env > b/board/phytec/phycore_imx93/phycore_imx93.env > new file mode 100644 > index 00000000000..27bfadfa140 > --- /dev/null > +++ b/board/phytec/phycore_imx93/phycore_imx93.env > @@ -0,0 +1,73 @@ > +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ > + > +image=Image > +console=ttyLP0 > +fdt_addr=0x83000000 > +fdto_addr=0x830c0000 > +bootenv_addr=0x83500000 > +fdt_file=CONFIG_DEFAULT_FDT_FILE > +ip_dyn=yes > +bootenv=bootenv.txt > +mmc_load_bootenv=fatload mmc ${mmcdev}:${mmcpart} ${bootenv_addr} > ${bootenv} > +mmcdev=CONFIG_SYS_MMC_ENV_DEV > +mmcpart=1 > +mmcroot=2 > +mmcautodetect=yes > +mmcargs=setenv bootargs console=${console},${baudrate} earlycon > + root=/dev/mmcblk${mmcdev}p${mmcroot} ${raucargs} rootwait rw > +loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image} > +loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file} > +mmc_load_overlay=fatload mmc ${mmcdev}:${mmcpart} ${fdto_addr} > ${overlay} > +mmc_apply_overlays= > + fdt address ${fdt_addr}; > + for overlay in ${overlays}; > + do; > + if run mmc_load_overlay; then > + fdt resize ${filesize}; > + fdt apply ${fdto_addr}; > + fi; > + done; > +mmcboot= > + echo Booting from mmc ...; > + if run mmc_load_bootenv; then > + env import -t ${bootenv_addr} ${filesize}; > + fi; > + run mmcargs; > + if run loadfdt; then > + run mmc_apply_overlays; > + booti ${loadaddr} - ${fdt_addr}; > + else > + echo WARN: Cannot load the DT; > + fi; > +nfsroot=/nfs > +netargs=setenv bootargs console=${console},${baudrate} earlycon > + root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp > +net_load_bootenv=${get_cmd} ${bootenv_addr} ${bootenv} > +net_load_overlay=${get_cmd} ${fdto_addr} ${overlay} > +net_apply_overlays= > + fdt address ${fdt_addr}; > + for overlay in ${overlays}; > + do; > + if run net_load_overlay; then > + fdt resize ${filesize}; > + fdt apply ${fdto_addr}; > + fi; > + done; > +netboot= > + echo Booting from net ...; > + run netargs; > + if test ${ip_dyn} = yes; then > + setenv get_cmd dhcp; > + else > + setenv get_cmd tftp; > + fi; > + if run net_load_bootenv; then > + env import -t ${bootenv_addr} ${filesize}; > + fi; > + ${get_cmd} ${loadaddr} ${image}; > + if ${get_cmd} ${fdt_addr} ${fdt_file}; then > + run net_apply_overlays; > + booti ${loadaddr} - ${fdt_addr}; > + else > + echo WARN: Cannot load the DT; > + fi; > diff --git a/board/phytec/phycore_imx93/spl.c > b/board/phytec/phycore_imx93/spl.c > new file mode 100644 > index 00000000000..da4b9e53594 > --- /dev/null > +++ b/board/phytec/phycore_imx93/spl.c > @@ -0,0 +1,148 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2023 PHYTEC Messtechnik GmbH > + * Author: Christoph Stoidner <c.stoidner@phytec.de> > + * Copyright (C) 2024 Mathieu Othacehe <m.othacehe@gmail.com> > + */ > + > +#include <asm/arch/clock.h> > +#include <asm/arch/ddr.h> > +#include <asm/arch/sys_proto.h> > +#include <asm/arch/trdc.h> > +#include <asm/mach-imx/boot_mode.h> > +#include <asm/sections.h> > +#include <hang.h> > +#include <init.h> > +#include <log.h> > +#include <power/pmic.h> > +#include <power/pca9450.h> > +#include <spl.h> > + > +DECLARE_GLOBAL_DATA_PTR; > + > +/* > + * Will be part of drivers/power/regulator/pca9450.c > + * when pca9451a support is added. > + */ > +#define PCA9450_REG_PWRCTRL_TOFF_DEB BIT(5) > + > +int spl_board_boot_device(enum boot_device boot_dev_spl) > +{ > + return BOOT_DEVICE_BOOTROM; > +} > + > +void spl_board_init(void) > +{ > + puts("Normal Boot\n"); > +} > + > +void spl_dram_init(void) > +{ > + ddr_init(&dram_timing); > +} > + > +int power_init_board(void) > +{ > + struct udevice *dev; > + int ret; > + unsigned int val = 0; > + > + ret = pmic_get("pmic@25", &dev); > + if (ret == -ENODEV) { > + puts("No pca9450@25\n"); > + return 0; > + } > + > + if (ret != 0) > + return ret; > + > + /* BUCKxOUT_DVS0/1 control BUCK123 output */ > + pmic_reg_write(dev, PCA9450_BUCK123_DVS, 0x29); > + > + /* enable DVS control through PMIC_STBY_REQ */ > + pmic_reg_write(dev, PCA9450_BUCK1CTRL, 0x59); > + > + ret = pmic_reg_read(dev, PCA9450_PWR_CTRL); > + if (ret < 0) > + return ret; > + val = ret; > + > + if (IS_ENABLED(CONFIG_IMX9_LOW_DRIVE_MODE)) { > + /* 0.8v for Low drive mode */ > + if (val & PCA9450_REG_PWRCTRL_TOFF_DEB) { > + pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, > 0x0c); > + pmic_reg_write(dev, PCA9450_BUCK3OUT_DVS0, > 0x0c); > + } else { > + pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, > 0x10); > + pmic_reg_write(dev, PCA9450_BUCK3OUT_DVS0, > 0x10); > + } > + } else { > + /* 0.9v for Over drive mode */ > + if (val & PCA9450_REG_PWRCTRL_TOFF_DEB) { > + pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, > 0x14); > + pmic_reg_write(dev, PCA9450_BUCK3OUT_DVS0, > 0x14); > + } else { > + pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, > 0x18); > + pmic_reg_write(dev, PCA9450_BUCK3OUT_DVS0, > 0x18); > + } > + } > + > + /* set standby voltage to 0.65v */ > + if (val & PCA9450_REG_PWRCTRL_TOFF_DEB) > + pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS1, 0x0); > + else > + pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS1, 0x4); > + > + /* I2C_LT_EN*/ > + pmic_reg_write(dev, 0xa, 0x3); > + > + return 0; > +} > + > +extern int imx9_probe_mu(void *ctx, struct event *event); > +void board_init_f(ulong dummy) > +{ > + int ret; > + > + /* Clear the BSS. */ > + memset(__bss_start, 0, __bss_end - __bss_start); > + > + timer_init(); > + > + arch_cpu_init(); > + > + spl_early_init(); > + > + preloader_console_init(); > + > + ret = imx9_probe_mu(NULL, NULL); > + if (ret) { > + printf("Fail to init ELE API\n"); > + } else { > + printf("SOC: 0x%x\n", gd->arch.soc_rev); > + printf("LC: 0x%x\n", gd->arch.lifecycle); > + } > + > + clock_init(); > + > + power_init_board(); > + > + if (!IS_ENABLED(CONFIG_IMX9_LOW_DRIVE_MODE)) > + set_arm_core_max_clk(); > + > + /* Init power of mix */ > + soc_power_init(); > + > + /* Setup TRDC for DDR access */ > + trdc_init(); > + > + /* DDR initialization */ > + spl_dram_init(); > + > + /* Put M33 into CPUWAIT for following kick */ > + ret = m33_prepare(); > + if (!ret) > + printf("M33 prepare ok\n"); > + > + board_init_r(NULL, 0); > +} > diff --git a/configs/imx93-phyboard-segin_defconfig b/configs/imx93- > phyboard-segin_defconfig > new file mode 100644 > index 00000000000..91a24c3456d > --- /dev/null > +++ b/configs/imx93-phyboard-segin_defconfig > @@ -0,0 +1,138 @@ > +CONFIG_ARM=y > +CONFIG_ARCH_IMX9=y > +CONFIG_TEXT_BASE=0x80200000 > +CONFIG_SYS_MALLOC_LEN=0x2000000 > +CONFIG_SYS_MALLOC_F_LEN=0x20000 > +CONFIG_SPL_LIBCOMMON_SUPPORT=y > +CONFIG_SPL_LIBGENERIC_SUPPORT=y > +CONFIG_NR_DRAM_BANKS=2 > +CONFIG_ENV_SOURCE_FILE="phycore_imx93" > +CONFIG_ENV_SIZE=0x10000 > +CONFIG_ENV_OFFSET=0x700000 > +CONFIG_IMX_CONFIG="arch/arm/mach-imx/imx9/imximage.cfg" > +CONFIG_DM_GPIO=y > +CONFIG_DEFAULT_DEVICE_TREE="imx93-phyboard-segin" > +CONFIG_SPL_TEXT_BASE=0x2049A000 > +CONFIG_AHAB_BOOT=y > +CONFIG_TARGET_PHYCORE_IMX93=y > +CONFIG_OF_LIBFDT_OVERLAY=y > +CONFIG_SYS_MONITOR_LEN=524288 > +CONFIG_SPL_SERIAL=y > +CONFIG_SPL_DRIVERS_MISC=y > +CONFIG_SPL_STACK=0x20519dd0 > +CONFIG_SPL=y > +CONFIG_ENV_OFFSET_REDUND=0x720000 > +CONFIG_CMD_DEKBLOB=y > +CONFIG_SPL_IMX_ROMAPI_LOADADDR=0x88000000 > +CONFIG_SYS_LOAD_ADDR=0x80400000 > +CONFIG_SYS_MEMTEST_START=0x80000000 > +CONFIG_SYS_MEMTEST_END=0x90000000 > +CONFIG_REMAKE_ELF=y > +CONFIG_DISTRO_DEFAULTS=y > +CONFIG_OF_SYSTEM_SETUP=y > +CONFIG_BOOTCOMMAND="mmc dev ${mmcdev}; if mmc rescan; then if run > loadimage; then run mmcboot; else run netboot; fi; fi;" > +CONFIG_DEFAULT_FDT_FILE="oftree" > +CONFIG_SYS_CBSIZE=2048 > +CONFIG_SYS_PBSIZE=2074 > +CONFIG_BOARD_LATE_INIT=y > +CONFIG_SPL_MAX_SIZE=0x26000 > +CONFIG_SPL_HAS_BSS_LINKER_SECTION=y > +CONFIG_SPL_BSS_START_ADDR=0x2051a000 > +CONFIG_SPL_BSS_MAX_SIZE=0x2000 > +CONFIG_SPL_BOARD_INIT=y > +CONFIG_SPL_BOOTROM_SUPPORT=y > +CONFIG_SPL_LOAD_IMX_CONTAINER=y > +CONFIG_IMX_CONTAINER_CFG="arch/arm/mach-imx/imx9/container.cfg" > +# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set > +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y > +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x1040 > +CONFIG_SPL_I2C=y > +CONFIG_SPL_POWER=y > +CONFIG_SPL_WATCHDOG=y > +CONFIG_SYS_PROMPT="u-boot=> " > +CONFIG_SYS_MAXARGS=64 > +CONFIG_CMD_ERASEENV=y > +CONFIG_CMD_NVEDIT_EFI=y > +CONFIG_CRC32_VERIFY=y > +CONFIG_CMD_EEPROM=y > +CONFIG_SYS_I2C_EEPROM_BUS=2 > +CONFIG_SYS_I2C_EEPROM_ADDR_LEN=2 > +CONFIG_SYS_EEPROM_SIZE=4096 > +CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=5 > +CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 > +CONFIG_CMD_MEMTEST=y > +CONFIG_CMD_CLK=y > +CONFIG_CMD_DFU=y > +CONFIG_CMD_FUSE=y > +CONFIG_CMD_GPIO=y > +CONFIG_CMD_I2C=y > +CONFIG_CMD_MMC=y > +CONFIG_CMD_POWEROFF=y > +CONFIG_CMD_SNTP=y > +CONFIG_CMD_CACHE=y > +CONFIG_CMD_EFIDEBUG=y > +CONFIG_CMD_RTC=y > +CONFIG_CMD_TIME=y > +CONFIG_CMD_GETTIME=y > +CONFIG_CMD_TIMER=y > +CONFIG_CMD_REGULATOR=y > +CONFIG_CMD_HASH=y > +CONFIG_CMD_EXT4_WRITE=y > +CONFIG_OF_CONTROL=y > +CONFIG_SPL_OF_CONTROL=y > +CONFIG_ENV_OVERWRITE=y > +CONFIG_ENV_IS_NOWHERE=y > +CONFIG_ENV_IS_IN_MMC=y > +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y > +CONFIG_SYS_RELOC_GD_ENV_ADDR=y > +CONFIG_SYS_MMC_ENV_DEV=1 > +CONFIG_USE_ETHPRIME=y > +CONFIG_ETHPRIME="eth1" > +CONFIG_NET_RANDOM_ETHADDR=y > +CONFIG_SPL_DM=y > +CONFIG_SPL_CLK_IMX93=y > +CONFIG_CLK_IMX93=y > +CONFIG_DFU_MMC=y > +CONFIG_DFU_RAM=y > +CONFIG_GPIO_HOG=y > +CONFIG_IMX_RGPIO2P=y > +CONFIG_DM_I2C=y > +CONFIG_SYS_I2C_IMX_LPI2C=y > +CONFIG_I2C_EEPROM=y > +CONFIG_SYS_I2C_EEPROM_ADDR=0x50 > +CONFIG_SUPPORT_EMMC_BOOT=y > +CONFIG_MMC_IO_VOLTAGE=y > +CONFIG_MMC_UHS_SUPPORT=y > +CONFIG_MMC_HS400_ES_SUPPORT=y > +CONFIG_MMC_HS400_SUPPORT=y > +CONFIG_FSL_USDHC=y > +CONFIG_PHY_TI_GENERIC=y > +CONFIG_DM_ETH_PHY=y > +CONFIG_DWC_ETH_QOS=y > +CONFIG_DWC_ETH_QOS_IMX=y > +CONFIG_FEC_MXC=y > +CONFIG_MII=y > +CONFIG_PINCTRL=y > +CONFIG_SPL_PINCTRL=y > +CONFIG_PINCTRL_IMX93=y > +CONFIG_POWER_DOMAIN=y > +CONFIG_DM_PMIC=y > +CONFIG_DM_PMIC_PCA9450=y > +CONFIG_SPL_DM_PMIC_PCA9450=y > +CONFIG_DM_REGULATOR=y > +CONFIG_DM_REGULATOR_PCA9450=y > +CONFIG_DM_REGULATOR_FIXED=y > +CONFIG_DM_REGULATOR_GPIO=y > +CONFIG_DM_RTC=y > +CONFIG_DM_SERIAL=y > +CONFIG_FSL_LPUART=y > +CONFIG_SPI=y > +CONFIG_DM_SPI=y > +CONFIG_SYSRESET=y > +CONFIG_SPL_SYSRESET=y > +CONFIG_SYSRESET_WATCHDOG=y > +CONFIG_DM_THERMAL=y > +CONFIG_IMX_TMU=y > +CONFIG_ULP_WATCHDOG=y > +CONFIG_LZO=y > +CONFIG_BZIP2=y > diff --git a/doc/board/phytec/imx93-phyboard-segin.rst > b/doc/board/phytec/imx93-phyboard-segin.rst > new file mode 100644 > index 00000000000..da8772ecd5c > --- /dev/null > +++ b/doc/board/phytec/imx93-phyboard-segin.rst > @@ -0,0 +1,61 @@ > +.. SPDX-License-Identifier: GPL-2.0+ > + > +phyBOARD-Segin-i.MX93 > +===================== > + > +U-Boot for the phyBOARD-Segin-i.MX93. > + > +Quick Start > +----------- > + > +- Get and Build the ARM Trusted firmware > +- Get the DDR firmware > +- Get ahab-container.img > +- Build U-Boot > + > +Get and Build the ARM Trusted firmware > +-------------------------------------- > + > +Note: srctree is U-Boot source directory > +Get ATF from: https://github.com/nxp-imx/imx-atf/ > +branch: lf_v2.8 > + > +.. code-block:: bash > + > + $ unset LDFLAGS > + $ make PLAT=imx93 bl31 > + $ cp build/imx93/release/bl31.bin $(srctree) > + > +Get the DDR firmware > +-------------------- > + > +.. code-block:: bash > + > + $ wget > https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.21.bin > + $ chmod +x firmware-imx-8.21.bin > + $ ./firmware-imx-8.21.bin > + $ cp firmware-imx-8.21/firmware/ddr/synopsys/lpddr4*.bin > $(srctree) > + > +Get ahab-container.img > +--------------------------------------- > + > +.. code-block:: bash > + > + $ wget > https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-sentinel-0.10.bin > + $ chmod +x firmware-sentinel-0.10.bin > + $ ./firmware-sentinel-0.10.bin > + $ cp firmware-sentinel-0.10/mx93a0-ahab-container.img $(srctree) > + > +Build U-Boot > +------------ > + > +.. code-block:: bash > + > + $ make imx93-phyboard-segin_defconfig > + $ make > + > +Burn the flash.bin to MicroSD card offset 32KB: > + > +.. code-block:: bash > + > + $ dd if=flash.bin of=/dev/sd[x] bs=1024 seek=32 conv=notrunc > diff --git a/doc/board/phytec/index.rst b/doc/board/phytec/index.rst > index 965d40de4d4..fea0b076202 100644 > --- a/doc/board/phytec/index.rst > +++ b/doc/board/phytec/index.rst > @@ -7,6 +7,7 @@ PHYTEC > :maxdepth: 2 > > imx8mm-phygate-tauri-l > + imx93-phyboard-segin > phycore-am62x > phycore-imx8mm > phycore-imx8mp > diff --git a/include/configs/phycore_imx93.h > b/include/configs/phycore_imx93.h > new file mode 100644 > index 00000000000..07364dff403 > --- /dev/null > +++ b/include/configs/phycore_imx93.h > @@ -0,0 +1,28 @@ > +/* SPDX-License-Identifier: GPL-2.0+ */ > +/* > + * Copyright 2022 NXP > + * Copyright (C) 2023 PHYTEC Messtechnik GmbH > + * Christoph Stoidner <c.stoidner@phytec.de> > + * Copyright (C) 2024 Mathieu Othacehe <m.othacehe@gmail.com> > + */ > + > +#ifndef __PHYCORE_IMX93_H > +#define __PHYCORE_IMX93_H > + > +#include <linux/sizes.h> > +#include <asm/arch/imx-regs.h> > + > +#define CFG_SYS_UBOOT_BASE \ > + (QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * > 512) > + > +#define CFG_SYS_INIT_RAM_ADDR 0x80000000 > +#define CFG_SYS_INIT_RAM_SIZE 0x200000 > + > +#define CFG_SYS_SDRAM_BASE 0x80000000 > +#define PHYS_SDRAM 0x80000000 > +#define PHYS_SDRAM_SIZE 0x80000000 > + > +/* Using ULP WDOG for reset */ > +#define WDOG_BASE_ADDR WDG3_BASE_ADDR > + > +#endif /* __PHYCORE_IMX93_H */
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 50f35e3db3f..1a20031b063 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -1130,7 +1130,8 @@ dtb-$(CONFIG_ARCH_IMX8M) += \ dtb-$(CONFIG_ARCH_IMX9) += \ imx93-11x11-evk.dtb \ - imx93-var-som-symphony.dtb + imx93-var-som-symphony.dtb \ + imx93-phyboard-segin.dtb dtb-$(CONFIG_ARCH_IMXRT) += imxrt1050-evk.dtb \ imxrt1020-evk.dtb \ diff --git a/arch/arm/dts/imx93-phyboard-segin-u-boot.dtsi b/arch/arm/dts/imx93-phyboard-segin-u-boot.dtsi new file mode 100644 index 00000000000..8bf28c2de87 --- /dev/null +++ b/arch/arm/dts/imx93-phyboard-segin-u-boot.dtsi @@ -0,0 +1,293 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2023 PHYTEC Messtechnik GmbH + * Christoph Stoidner <c.stoidner@phytec.de> + * + * Product homepage: + * phyBOARD-Segin carrier board is reused for the i.MX93 design. + * https://www.phytec.eu/en/produkte/single-board-computer/phyboard-segin-imx6ul/ + */ + +#include "imx93-u-boot.dtsi" + +/ { + wdt-reboot { + compatible = "wdt-reboot"; + wdt = <&wdog3>; + bootph-pre-ram; + bootph-some-ram; + }; + + aliases { + ethernet0 = &fec; + ethernet1 = &eqos; + }; + + firmware { + optee { + compatible = "linaro,optee-tz"; + method = "smc"; + }; + }; +}; + +&{/soc@0} { + bootph-all; + bootph-pre-ram; +}; + +&aips1 { + bootph-pre-ram; + bootph-all; +}; + +&aips2 { + bootph-pre-ram; + bootph-some-ram; +}; + +&aips3 { + bootph-pre-ram; + bootph-some-ram; +}; + +&iomuxc { + bootph-pre-ram; + bootph-some-ram; +}; + +®_usdhc2_vmmc { + u-boot,off-on-delay-us = <20000>; + bootph-pre-ram; + bootph-some-ram; +}; + +&pinctrl_reg_usdhc2_vmmc { + bootph-pre-ram; +}; + +&pinctrl_uart1 { + bootph-pre-ram; + bootph-some-ram; +}; + +&pinctrl_usdhc1 { + bootph-pre-ram; + bootph-some-ram; +}; + +&pinctrl_usdhc2_cd { + bootph-pre-ram; + bootph-some-ram; +}; + +&pinctrl_usdhc2_default { + bootph-pre-ram; + bootph-some-ram; +}; + +&pinctrl_usdhc2_100mhz { + bootph-pre-ram; + bootph-some-ram; +}; + +&pinctrl_usdhc2_200mhz { + bootph-pre-ram; + bootph-some-ram; +}; + +&gpio1 { + bootph-pre-ram; + bootph-some-ram; +}; + +&gpio2 { + bootph-pre-ram; + bootph-some-ram; +}; + +&gpio3 { + bootph-pre-ram; + bootph-some-ram; +}; + +&gpio4 { + bootph-pre-ram; + bootph-some-ram; +}; + +&lpuart1 { + bootph-pre-ram; + bootph-some-ram; +}; + +&usdhc1 { + bootph-pre-ram; + bootph-some-ram; +}; + +&usdhc2 { + bootph-pre-ram; + bootph-some-ram; + fsl,signal-voltage-switch-extra-delay-ms = <8>; +}; + +&lpi2c1 { + bootph-pre-ram; + bootph-some-ram; +}; + +&lpi2c2 { + bootph-pre-ram; + bootph-some-ram; +}; + +&lpi2c3 { + bootph-pre-ram; + bootph-some-ram; +}; + +&s4muap { + bootph-pre-ram; + bootph-some-ram; + status = "okay"; +}; + +&clk { + bootph-all; + bootph-pre-ram; + /delete-property/ assigned-clocks; + /delete-property/ assigned-clock-rates; + /delete-property/ assigned-clock-parents; +}; + +&osc_32k { + bootph-all; + bootph-pre-ram; +}; + +&osc_24m { + bootph-all; + bootph-pre-ram; +}; + +&clk_ext1 { + bootph-all; + bootph-pre-ram; +}; + +&wdog3 { + bootph-all; + bootph-pre-ram; +}; + +/* + * The two nodes below won't be needed once nxp,pca9451a + * support is added to the Linux kernel. + */ +&iomuxc { + pinctrl_lpi2c3: lpi2c3grp { + bootph-pre-ram; + fsl,pins = < + MX93_PAD_GPIO_IO28__LPI2C3_SDA 0x40000b9e + MX93_PAD_GPIO_IO29__LPI2C3_SCL 0x40000b9e + >; + }; + + pinctrl_pmic: pmicgrp { + bootph-pre-ram; + fsl,pins = < + MX93_PAD_ENET2_RD3__GPIO4_IO27 0x31e + >; + }; +}; + +&lpi2c3 { + bootph-pre-ram; + bootph-some-ram; + clock-frequency = <400000>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&pinctrl_lpi2c3>; + pinctrl-1 = <&pinctrl_lpi2c3>; + status = "okay"; + + pmic@25 { + bootph-pre-ram; + bootph-some-ram; + compatible = "nxp,pca9451a"; + reg = <0x25>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio4>; + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; + + regulators { + bootph-pre-ram; + bootph-some-ram; + buck1: BUCK1 { + regulator-name = "VDD_SOC"; + regulator-min-microvolt = <610000>; + regulator-max-microvolt = <950000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + }; + + buck2: BUCK2 { + regulator-name = "VDDQ_0V6"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <600000>; + regulator-boot-on; + regulator-always-on; + }; + + buck4: BUCK4 { + regulator-name = "VDD_3V3_BUCK"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + buck5: BUCK5 { + regulator-name = "VDD_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + buck6: BUCK6 { + regulator-name = "VDD_1V1"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1: LDO1 { + regulator-name = "PMIC_SNVS_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4: LDO4 { + regulator-name = "VDD_0V8"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo5: LDO5 { + regulator-name = "NVCC_SD2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; diff --git a/arch/arm/dts/imx93-phyboard-segin.dts b/arch/arm/dts/imx93-phyboard-segin.dts new file mode 100644 index 00000000000..85fb188b057 --- /dev/null +++ b/arch/arm/dts/imx93-phyboard-segin.dts @@ -0,0 +1,117 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2023 PHYTEC Messtechnik GmbH + * Author: Wadim Egorov <w.egorov@phytec.de>, Christoph Stoidner <c.stoidner@phytec.de> + * Copyright (C) 2024 Mathieu Othacehe <m.othacehe@gmail.com> + * + * Product homepage: + * phyBOARD-Segin carrier board is reused for the i.MX93 design. + * https://www.phytec.eu/en/produkte/single-board-computer/phyboard-segin-imx6ul/ + */ +/dts-v1/; + +#include "imx93-phycore-som.dtsi" + +/{ + model = "PHYTEC phyBOARD-Segin-i.MX93"; + compatible = "phytec,imx93-phyboard-segin", "phytec,imx93-phycore-som", + "fsl,imx93"; + + chosen { + stdout-path = &lpuart1; + }; + + reg_usdhc2_vmmc: regulator-usdhc2 { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "VCC_SD"; + }; +}; + +/* Console */ +&lpuart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +/* eMMC */ +&usdhc1 { + no-1-8-v; +}; + +/* SD-Card */ +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2_default>, <&pinctrl_usdhc2_cd>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_cd>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_cd>; + bus-width = <4>; + cd-gpios = <&gpio3 0 GPIO_ACTIVE_LOW>; + no-mmc; + no-sdio; + vmmc-supply = <®_usdhc2_vmmc>; + status = "okay"; +}; + +&iomuxc { + pinctrl_uart1: uart1grp { + fsl,pins = < + MX93_PAD_UART1_RXD__LPUART1_RX 0x31e + MX93_PAD_UART1_TXD__LPUART1_TX 0x30e + >; + }; + + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp { + fsl,pins = < + MX93_PAD_SD2_RESET_B__GPIO3_IO07 0x31e + >; + }; + + pinctrl_usdhc2_cd: usdhc2cdgrp { + fsl,pins = < + MX93_PAD_SD2_CD_B__GPIO3_IO00 0x31e + >; + }; + + pinctrl_usdhc2_default: usdhc2grp { + fsl,pins = < + MX93_PAD_SD2_CLK__USDHC2_CLK 0x179e + MX93_PAD_SD2_CMD__USDHC2_CMD 0x139e + MX93_PAD_SD2_DATA0__USDHC2_DATA0 0x138e + MX93_PAD_SD2_DATA1__USDHC2_DATA1 0x138e + MX93_PAD_SD2_DATA2__USDHC2_DATA2 0x138e + MX93_PAD_SD2_DATA3__USDHC2_DATA3 0x139e + MX93_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2grp { + fsl,pins = < + MX93_PAD_SD2_CLK__USDHC2_CLK 0x179e + MX93_PAD_SD2_CMD__USDHC2_CMD 0x139e + MX93_PAD_SD2_DATA0__USDHC2_DATA0 0x138e + MX93_PAD_SD2_DATA1__USDHC2_DATA1 0x138e + MX93_PAD_SD2_DATA2__USDHC2_DATA2 0x139e + MX93_PAD_SD2_DATA3__USDHC2_DATA3 0x139e + MX93_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2grp { + fsl,pins = < + MX93_PAD_SD2_CLK__USDHC2_CLK 0x178e + MX93_PAD_SD2_CMD__USDHC2_CMD 0x139e + MX93_PAD_SD2_DATA0__USDHC2_DATA0 0x139e + MX93_PAD_SD2_DATA1__USDHC2_DATA1 0x139e + MX93_PAD_SD2_DATA2__USDHC2_DATA2 0x139e + MX93_PAD_SD2_DATA3__USDHC2_DATA3 0x139e + MX93_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e + >; + }; +}; diff --git a/arch/arm/dts/imx93-phycore-som.dtsi b/arch/arm/dts/imx93-phycore-som.dtsi new file mode 100644 index 00000000000..88c2657b50e --- /dev/null +++ b/arch/arm/dts/imx93-phycore-som.dtsi @@ -0,0 +1,126 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2023 PHYTEC Messtechnik GmbH + * Author: Wadim Egorov <w.egorov@phytec.de>, Christoph Stoidner <c.stoidner@phytec.de> + * Copyright (C) 2024 Mathieu Othacehe <m.othacehe@gmail.com> + * + * Product homepage: + * https://www.phytec.eu/en/produkte/system-on-modules/phycore-imx-91-93/ + */ + +#include <dt-bindings/leds/common.h> + +#include "imx93.dtsi" + +/{ + model = "PHYTEC phyCORE-i.MX93"; + compatible = "phytec,imx93-phycore-som", "fsl,imx93"; + + reserved-memory { + ranges; + #address-cells = <2>; + #size-cells = <2>; + + linux,cma { + compatible = "shared-dma-pool"; + reusable; + alloc-ranges = <0 0x80000000 0 0x40000000>; + size = <0 0x10000000>; + linux,cma-default; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + + led-0 { + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_HEARTBEAT; + gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +/* Ethernet */ +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec>; + phy-mode = "rmii"; + phy-handle = <ðphy1>; + fsl,magic-packet; + assigned-clocks = <&clk IMX93_CLK_ENET_TIMER1>, + <&clk IMX93_CLK_ENET_REF>, + <&clk IMX93_CLK_ENET_REF_PHY>; + assigned-clock-parents = <&clk IMX93_CLK_SYS_PLL_PFD1_DIV2>, + <&clk IMX93_CLK_SYS_PLL_PFD1_DIV2>, + <&clk IMX93_CLK_SYS_PLL_PFD1_DIV2>; + assigned-clock-rates = <100000000>, <50000000>, <50000000>; + status = "okay"; + + mdio: mdio { + clock-frequency = <5000000>; + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; + }; +}; + +/* eMMC */ +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +/* Watchdog */ +&wdog3 { + status = "okay"; +}; + +&iomuxc { + pinctrl_fec: fecgrp { + fsl,pins = < + MX93_PAD_ENET2_MDC__ENET1_MDC 0x50e + MX93_PAD_ENET2_MDIO__ENET1_MDIO 0x502 + MX93_PAD_ENET2_RD0__ENET1_RGMII_RD0 0x57e + MX93_PAD_ENET2_RD1__ENET1_RGMII_RD1 0x57e + MX93_PAD_ENET2_RXC__ENET1_RX_ER 0x5fe + MX93_PAD_ENET2_RX_CTL__ENET1_RGMII_RX_CTL 0x57e + MX93_PAD_ENET2_TD0__ENET1_RGMII_TD0 0x50e + MX93_PAD_ENET2_TD1__ENET1_RGMII_TD1 0x50e + MX93_PAD_ENET2_TX_CTL__ENET1_RGMII_TX_CTL 0x50e + MX93_PAD_ENET2_TD2__ENET1_TX_CLK 0x4000050e + >; + }; + + pinctrl_leds: ledsgrp { + fsl,pins = < + MX93_PAD_I2C1_SDA__GPIO1_IO01 0x31e + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX93_PAD_SD1_CLK__USDHC1_CLK 0x179e + MX93_PAD_SD1_CMD__USDHC1_CMD 0x1386 + MX93_PAD_SD1_DATA0__USDHC1_DATA0 0x138e + MX93_PAD_SD1_DATA1__USDHC1_DATA1 0x1386 + MX93_PAD_SD1_DATA2__USDHC1_DATA2 0x138e + MX93_PAD_SD1_DATA3__USDHC1_DATA3 0x1386 + MX93_PAD_SD1_DATA4__USDHC1_DATA4 0x1386 + MX93_PAD_SD1_DATA5__USDHC1_DATA5 0x1386 + MX93_PAD_SD1_DATA6__USDHC1_DATA6 0x1386 + MX93_PAD_SD1_DATA7__USDHC1_DATA7 0x1386 + MX93_PAD_SD1_STROBE__USDHC1_STROBE 0x179e + >; + }; +}; diff --git a/arch/arm/mach-imx/imx9/Kconfig b/arch/arm/mach-imx/imx9/Kconfig index 961d6f527ab..b79485f1f75 100644 --- a/arch/arm/mach-imx/imx9/Kconfig +++ b/arch/arm/mach-imx/imx9/Kconfig @@ -37,9 +37,15 @@ config TARGET_IMX93_VAR_SOM select IMX93 select IMX9_LPDDR4X +config TARGET_PHYCORE_IMX93 + bool "phycore_imx93" + select IMX93 + select IMX9_LPDDR4X + endchoice source "board/freescale/imx93_evk/Kconfig" +source "board/phytec/phycore_imx93/Kconfig" source "board/variscite/imx93_var_som/Kconfig" endif diff --git a/board/phytec/phycore_imx93/Kconfig b/board/phytec/phycore_imx93/Kconfig new file mode 100644 index 00000000000..a70104cb798 --- /dev/null +++ b/board/phytec/phycore_imx93/Kconfig @@ -0,0 +1,13 @@ + +if TARGET_PHYCORE_IMX93 + +config SYS_BOARD + default "phycore_imx93" + +config SYS_VENDOR + default "phytec" + +config SYS_CONFIG_NAME + default "phycore_imx93" + +endif diff --git a/board/phytec/phycore_imx93/MAINTAINERS b/board/phytec/phycore_imx93/MAINTAINERS new file mode 100644 index 00000000000..9e91a29dc31 --- /dev/null +++ b/board/phytec/phycore_imx93/MAINTAINERS @@ -0,0 +1,10 @@ +phyCORE-i.MX93 +M: Mathieu Othacehe <m.othacehe@gmail.com> +W: https://www.phytec.eu/en/produkte/system-on-modules/phycore-imx-91-93/ +S: Maintained +F: arch/arm/dts/imx93-phyboard-segin.dts +F: arch/arm/dts/imx93-phycore-som.dtsi +F: arch/arm/dts/imx93-phyboard-segin-u-boot.dtsi +F: board/phytec/phycore_imx93/ +F: configs/imx93-phyboard-segin_defconfig +F: include/configs/phycore_imx93.h diff --git a/board/phytec/phycore_imx93/Makefile b/board/phytec/phycore_imx93/Makefile new file mode 100644 index 00000000000..ce35326a156 --- /dev/null +++ b/board/phytec/phycore_imx93/Makefile @@ -0,0 +1,14 @@ +# +# Copyright 2022 NXP +# Copyright (C) 2023 PHYTEC Messtechnik GmbH +# Christoph Stoidner <c.stoidner@phytec.de> +# Copyright (C) 2024 Mathieu Othacehe <m.othacehe@gmail.com> +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += phycore-imx93.o + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o lpddr4_timing.o +endif diff --git a/board/phytec/phycore_imx93/lpddr4_timing.c b/board/phytec/phycore_imx93/lpddr4_timing.c new file mode 100644 index 00000000000..2111972a40e --- /dev/null +++ b/board/phytec/phycore_imx93/lpddr4_timing.c @@ -0,0 +1,1546 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2023 NXP + * Copyright (C) 2023 PHYTEC Messtechnik GmbH + * Christoph Stoidner <c.stoidner@phytec.de> + * + * Code generated with DDR Tool v1.0.0. + */ + +#include <linux/kernel.h> +#include <asm/arch/ddr.h> + +static struct dram_cfg_param ddr_ddrc_cfg[] = { + /** Initialize DDRC registers **/ + {0x4e300110, 0x44100001}, + {0x4e300000, 0x8000bf}, + {0x4e300008, 0x0}, + {0x4e300080, 0x80000412}, + {0x4e300084, 0x0}, + {0x4e300114, 0x1002}, + {0x4e300260, 0x4080}, + {0x4e300f04, 0x80}, + {0x4e300800, 0x43b30002}, + {0x4e300804, 0x1f1f1f1f}, + {0x4e301000, 0x0}, + {0x4e301240, 0x0}, + {0x4e301244, 0x0}, + {0x4e301248, 0x0}, + {0x4e30124c, 0x0}, + {0x4e301250, 0x0}, + {0x4e301254, 0x0}, + {0x4e301258, 0x0}, + {0x4e30125c, 0x0}, + +}; + +/* dram fsp cfg */ +static struct dram_fsp_cfg ddr_dram_fsp_cfg[] = { + { + { + {0x4e300100, 0x24A0421B}, + {0x4e300104, 0xF8EE001B}, + {0x4e300108, 0x2F263233}, + {0x4e30010C, 0x0005E18B}, + {0x4e300124, 0x1C770000}, + {0x4e300160, 0x00009102}, + {0x4e30016C, 0x35F00000}, + {0x4e300170, 0x8B0B0608}, + {0x4e300250, 0x00000028}, + {0x4e300254, 0x00FE00FE}, + {0x4e300258, 0x00000008}, + {0x4e30025C, 0x00000400}, + {0x4e300300, 0x224F2215}, + {0x4e300304, 0x00FE2213}, + {0x4e300308, 0x0A3C0E3C}, + }, + { + {0x01, 0xE4}, + {0x02, 0x36}, + {0x03, 0xF2}, + {0x0b, 0x46}, + {0x0c, 0x11}, + {0x0e, 0x11}, + {0x16, 0x04}, + }, + 0, + }, + +}; + +/* PHY Initialize Configuration */ +static struct dram_cfg_param ddr_ddrphy_cfg[] = { + {0x100a0, 0x0}, + {0x100a1, 0x1}, + {0x100a2, 0x2}, + {0x100a3, 0x3}, + {0x100a4, 0x4}, + {0x100a5, 0x5}, + {0x100a6, 0x6}, + {0x100a7, 0x7}, + {0x110a0, 0x0}, + {0x110a1, 0x1}, + {0x110a2, 0x2}, + {0x110a3, 0x3}, + {0x110a4, 0x4}, + {0x110a5, 0x5}, + {0x110a6, 0x6}, + {0x110a7, 0x7}, + {0x1005f, 0x5ff}, + {0x1015f, 0x5ff}, + {0x1105f, 0x5ff}, + {0x1115f, 0x5ff}, + {0x55, 0x1ff}, + {0x1055, 0x1ff}, + {0x2055, 0x1ff}, + {0x200c5, 0x19}, + {0x2002e, 0x2}, + {0x90204, 0x0}, + {0x20024, 0x1e3}, + {0x2003a, 0x2}, + {0x2007d, 0x212}, + {0x2007c, 0x61}, + {0x20056, 0x3}, + {0x1004d, 0x600}, + {0x1014d, 0x600}, + {0x1104d, 0x600}, + {0x1114d, 0x600}, + {0x10049, 0xe00}, + {0x10149, 0xe00}, + {0x11049, 0xe00}, + {0x11149, 0xe00}, + {0x43, 0x60}, + {0x1043, 0x60}, + {0x2043, 0x60}, + {0x20018, 0x1}, + {0x20075, 0x4}, + {0x20050, 0x0}, + {0x2009b, 0x2}, + {0x20008, 0x3a5}, + {0x20088, 0x9}, + {0x200b2, 0x10c}, + {0x10043, 0x5a1}, + {0x10143, 0x5a1}, + {0x11043, 0x5a1}, + {0x11143, 0x5a1}, + {0x200fa, 0x2}, + {0x20019, 0x1}, + {0x200f0, 0x600}, + {0x200f1, 0x0}, + {0x200f2, 0x4444}, + {0x200f3, 0x8888}, + {0x200f4, 0x5655}, + {0x200f5, 0x0}, + {0x200f6, 0x0}, + {0x200f7, 0xf000}, + {0x20025, 0x0}, + {0x2002d, 0x1}, + {0x2002c, 0x0}, + {0x20021, 0x0}, + {0x200c7, 0x21}, + {0x1200c7, 0x21}, + {0x200ca, 0x24}, + {0x1200ca, 0x24}, + +}; + +/* ddr phy trained csr */ +static struct dram_cfg_param ddr_ddrphy_trained_csr[] = { + {0x1005f, 0x0}, + {0x1015f, 0x0}, + {0x1105f, 0x0}, + {0x1115f, 0x0}, + {0x55, 0x0}, + {0x1055, 0x0}, + {0x2055, 0x0}, + {0x200c5, 0x0}, + {0x2002e, 0x0}, + {0x90204, 0x0}, + {0x20024, 0x0}, + {0x2003a, 0x0}, + {0x2007d, 0x0}, + {0x2007c, 0x0}, + {0x20056, 0x0}, + {0x1004d, 0x0}, + {0x1014d, 0x0}, + {0x1104d, 0x0}, + {0x1114d, 0x0}, + {0x10049, 0x0}, + {0x10149, 0x0}, + {0x11049, 0x0}, + {0x11149, 0x0}, + {0x43, 0x0}, + {0x1043, 0x0}, + {0x2043, 0x0}, + {0x20018, 0x0}, + {0x20075, 0x0}, + {0x20050, 0x0}, + {0x2009b, 0x0}, + {0x20008, 0x0}, + {0x20088, 0x0}, + {0x200b2, 0x0}, + {0x10043, 0x0}, + {0x10143, 0x0}, + {0x11043, 0x0}, + {0x11143, 0x0}, + {0x200fa, 0x0}, + {0x20019, 0x0}, + {0x200f0, 0x0}, + {0x200f1, 0x0}, + {0x200f2, 0x0}, + {0x200f3, 0x0}, + {0x200f4, 0x0}, + {0x200f5, 0x0}, + {0x200f6, 0x0}, + {0x200f7, 0x0}, + {0x20025, 0x0}, + {0x2002d, 0x0}, + {0x2002c, 0x0}, + {0xd0000, 0x0}, + {0x90000, 0x0}, + {0x90001, 0x0}, + {0x90002, 0x0}, + {0x90003, 0x0}, + {0x90004, 0x0}, + {0x90005, 0x0}, + {0x90029, 0x0}, + {0x9002a, 0x0}, + {0x9002b, 0x0}, + {0x9002c, 0x0}, + {0x9002d, 0x0}, + {0x9002e, 0x0}, + {0x9002f, 0x0}, + {0x90030, 0x0}, + {0x90031, 0x0}, + {0x90032, 0x0}, + {0x90033, 0x0}, + {0x90034, 0x0}, + {0x90035, 0x0}, + {0x90036, 0x0}, + {0x90037, 0x0}, + {0x90038, 0x0}, + {0x90039, 0x0}, + {0x9003a, 0x0}, + {0x9003b, 0x0}, + {0x9003c, 0x0}, + {0x9003d, 0x0}, + {0x9003e, 0x0}, + {0x9003f, 0x0}, + {0x90040, 0x0}, + {0x90041, 0x0}, + {0x90042, 0x0}, + {0x90043, 0x0}, + {0x90044, 0x0}, + {0x90045, 0x0}, + {0x90046, 0x0}, + {0x90047, 0x0}, + {0x90048, 0x0}, + {0x90049, 0x0}, + {0x9004a, 0x0}, + {0x9004b, 0x0}, + {0x9004c, 0x0}, + {0x9004d, 0x0}, + {0x9004e, 0x0}, + {0x9004f, 0x0}, + {0x90050, 0x0}, + {0x90051, 0x0}, + {0x90052, 0x0}, + {0x90053, 0x0}, + {0x90054, 0x0}, + {0x90055, 0x0}, + {0x90056, 0x0}, + {0x90057, 0x0}, + {0x90058, 0x0}, + {0x90059, 0x0}, + {0x9005a, 0x0}, + {0x9005b, 0x0}, + {0x9005c, 0x0}, + {0x9005d, 0x0}, + {0x9005e, 0x0}, + {0x9005f, 0x0}, + {0x90060, 0x0}, + {0x90061, 0x0}, + {0x90062, 0x0}, + {0x90063, 0x0}, + {0x90064, 0x0}, + {0x90065, 0x0}, + {0x90066, 0x0}, + {0x90067, 0x0}, + {0x90068, 0x0}, + {0x90069, 0x0}, + {0x9006a, 0x0}, + {0x9006b, 0x0}, + {0x9006c, 0x0}, + {0x9006d, 0x0}, + {0x9006e, 0x0}, + {0x9006f, 0x0}, + {0x90070, 0x0}, + {0x90071, 0x0}, + {0x90072, 0x0}, + {0x90073, 0x0}, + {0x90074, 0x0}, + {0x90075, 0x0}, + {0x90076, 0x0}, + {0x90077, 0x0}, + {0x90078, 0x0}, + {0x90079, 0x0}, + {0x9007a, 0x0}, + {0x9007b, 0x0}, + {0x9007c, 0x0}, + {0x9007d, 0x0}, + {0x9007e, 0x0}, + {0x9007f, 0x0}, + {0x90080, 0x0}, + {0x90081, 0x0}, + {0x90082, 0x0}, + {0x90083, 0x0}, + {0x90084, 0x0}, + {0x90085, 0x0}, + {0x90086, 0x0}, + {0x90087, 0x0}, + {0x90088, 0x0}, + {0x90089, 0x0}, + {0x9008a, 0x0}, + {0x9008b, 0x0}, + {0x9008c, 0x0}, + {0x9008d, 0x0}, + {0x9008e, 0x0}, + {0x9008f, 0x0}, + {0x90090, 0x0}, + {0x90091, 0x0}, + {0x90092, 0x0}, + {0x90093, 0x0}, + {0x90094, 0x0}, + {0x90095, 0x0}, + {0x90096, 0x0}, + {0x90097, 0x0}, + {0x90098, 0x0}, + {0x90099, 0x0}, + {0x9009a, 0x0}, + {0x9009b, 0x0}, + {0x9009c, 0x0}, + {0x9009d, 0x0}, + {0x9009e, 0x0}, + {0x9009f, 0x0}, + {0x900a0, 0x0}, + {0x900a1, 0x0}, + {0x900a2, 0x0}, + {0x900a3, 0x0}, + {0x900a4, 0x0}, + {0x900a5, 0x0}, + {0x900a6, 0x0}, + {0x900a7, 0x0}, + {0x900a8, 0x0}, + {0x900a9, 0x0}, + {0x40000, 0x0}, + {0x40020, 0x0}, + {0x40040, 0x0}, + {0x40060, 0x0}, + {0x40001, 0x0}, + {0x40021, 0x0}, + {0x40041, 0x0}, + {0x40061, 0x0}, + {0x40002, 0x0}, + {0x40022, 0x0}, + {0x40042, 0x0}, + {0x40062, 0x0}, + {0x40003, 0x0}, + {0x40023, 0x0}, + {0x40043, 0x0}, + {0x40063, 0x0}, + {0x40004, 0x0}, + {0x40024, 0x0}, + {0x40044, 0x0}, + {0x40064, 0x0}, + {0x40005, 0x0}, + {0x40025, 0x0}, + {0x40045, 0x0}, + {0x40065, 0x0}, + {0x40006, 0x0}, + {0x40026, 0x0}, + {0x40046, 0x0}, + {0x40066, 0x0}, + {0x40007, 0x0}, + {0x40027, 0x0}, + {0x40047, 0x0}, + {0x40067, 0x0}, + {0x40008, 0x0}, + {0x40028, 0x0}, + {0x40048, 0x0}, + {0x40068, 0x0}, + {0x40009, 0x0}, + {0x40029, 0x0}, + {0x40049, 0x0}, + {0x40069, 0x0}, + {0x4000a, 0x0}, + {0x4002a, 0x0}, + {0x4004a, 0x0}, + {0x4006a, 0x0}, + {0x4000b, 0x0}, + {0x4002b, 0x0}, + {0x4004b, 0x0}, + {0x4006b, 0x0}, + {0x4000c, 0x0}, + {0x4002c, 0x0}, + {0x4004c, 0x0}, + {0x4006c, 0x0}, + {0x4000d, 0x0}, + {0x4002d, 0x0}, + {0x4004d, 0x0}, + {0x4006d, 0x0}, + {0x4000e, 0x0}, + {0x4002e, 0x0}, + {0x4004e, 0x0}, + {0x4006e, 0x0}, + {0x4000f, 0x0}, + {0x4002f, 0x0}, + {0x4004f, 0x0}, + {0x4006f, 0x0}, + {0x40010, 0x0}, + {0x40030, 0x0}, + {0x40050, 0x0}, + {0x40070, 0x0}, + {0x40011, 0x0}, + {0x40031, 0x0}, + {0x40051, 0x0}, + {0x40071, 0x0}, + {0x40012, 0x0}, + {0x40032, 0x0}, + {0x40052, 0x0}, + {0x40072, 0x0}, + {0x40013, 0x0}, + {0x40033, 0x0}, + {0x40053, 0x0}, + {0x40073, 0x0}, + {0x40014, 0x0}, + {0x40034, 0x0}, + {0x40054, 0x0}, + {0x40074, 0x0}, + {0x40015, 0x0}, + {0x40035, 0x0}, + {0x40055, 0x0}, + {0x40075, 0x0}, + {0x40016, 0x0}, + {0x40036, 0x0}, + {0x40056, 0x0}, + {0x40076, 0x0}, + {0x40017, 0x0}, + {0x40037, 0x0}, + {0x40057, 0x0}, + {0x40077, 0x0}, + {0x40018, 0x0}, + {0x40038, 0x0}, + {0x40058, 0x0}, + {0x40078, 0x0}, + {0x40019, 0x0}, + {0x40039, 0x0}, + {0x40059, 0x0}, + {0x40079, 0x0}, + {0x4001a, 0x0}, + {0x4003a, 0x0}, + {0x4005a, 0x0}, + {0x4007a, 0x0}, + {0x900aa, 0x0}, + {0x900ab, 0x0}, + {0x900ac, 0x0}, + {0x900ad, 0x0}, + {0x900ae, 0x0}, + {0x900af, 0x0}, + {0x900b0, 0x0}, + {0x900b1, 0x0}, + {0x900b2, 0x0}, + {0x900b3, 0x0}, + {0x900b4, 0x0}, + {0x900b5, 0x0}, + {0x900b6, 0x0}, + {0x900b7, 0x0}, + {0x900b8, 0x0}, + {0x900b9, 0x0}, + {0x900ba, 0x0}, + {0x900bb, 0x0}, + {0x900bc, 0x0}, + {0x900bd, 0x0}, + {0x900be, 0x0}, + {0x900bf, 0x0}, + {0x900c0, 0x0}, + {0x900c1, 0x0}, + {0x900c2, 0x0}, + {0x900c3, 0x0}, + {0x900c4, 0x0}, + {0x900c5, 0x0}, + {0x900c6, 0x0}, + {0x900c7, 0x0}, + {0x900c8, 0x0}, + {0x900c9, 0x0}, + {0x900ca, 0x0}, + {0x900cb, 0x0}, + {0x900cc, 0x0}, + {0x900cd, 0x0}, + {0x900ce, 0x0}, + {0x900cf, 0x0}, + {0x900d0, 0x0}, + {0x900d1, 0x0}, + {0x900d2, 0x0}, + {0x900d3, 0x0}, + {0x900d4, 0x0}, + {0x900d5, 0x0}, + {0x900d6, 0x0}, + {0x900d7, 0x0}, + {0x900d8, 0x0}, + {0x900d9, 0x0}, + {0x900da, 0x0}, + {0x900db, 0x0}, + {0x900dc, 0x0}, + {0x900dd, 0x0}, + {0x900de, 0x0}, + {0x900df, 0x0}, + {0x900e0, 0x0}, + {0x900e1, 0x0}, + {0x900e2, 0x0}, + {0x900e3, 0x0}, + {0x900e4, 0x0}, + {0x900e5, 0x0}, + {0x900e6, 0x0}, + {0x900e7, 0x0}, + {0x900e8, 0x0}, + {0x900e9, 0x0}, + {0x900ea, 0x0}, + {0x900eb, 0x0}, + {0x900ec, 0x0}, + {0x900ed, 0x0}, + {0x900ee, 0x0}, + {0x900ef, 0x0}, + {0x900f0, 0x0}, + {0x900f1, 0x0}, + {0x900f2, 0x0}, + {0x900f3, 0x0}, + {0x900f4, 0x0}, + {0x900f5, 0x0}, + {0x900f6, 0x0}, + {0x900f7, 0x0}, + {0x900f8, 0x0}, + {0x900f9, 0x0}, + {0x900fa, 0x0}, + {0x900fb, 0x0}, + {0x900fc, 0x0}, + {0x900fd, 0x0}, + {0x900fe, 0x0}, + {0x900ff, 0x0}, + {0x90100, 0x0}, + {0x90101, 0x0}, + {0x90102, 0x0}, + {0x90103, 0x0}, + {0x90104, 0x0}, + {0x90105, 0x0}, + {0x90106, 0x0}, + {0x90107, 0x0}, + {0x90108, 0x0}, + {0x90109, 0x0}, + {0x9010a, 0x0}, + {0x9010b, 0x0}, + {0x9010c, 0x0}, + {0x9010d, 0x0}, + {0x9010e, 0x0}, + {0x9010f, 0x0}, + {0x90110, 0x0}, + {0x90111, 0x0}, + {0x90112, 0x0}, + {0x90113, 0x0}, + {0x90114, 0x0}, + {0x90115, 0x0}, + {0x90116, 0x0}, + {0x90117, 0x0}, + {0x90118, 0x0}, + {0x90119, 0x0}, + {0x9011a, 0x0}, + {0x9011b, 0x0}, + {0x9011c, 0x0}, + {0x9011d, 0x0}, + {0x9011e, 0x0}, + {0x9011f, 0x0}, + {0x90120, 0x0}, + {0x90121, 0x0}, + {0x90122, 0x0}, + {0x90123, 0x0}, + {0x90124, 0x0}, + {0x90125, 0x0}, + {0x90126, 0x0}, + {0x90127, 0x0}, + {0x90128, 0x0}, + {0x90129, 0x0}, + {0x9012a, 0x0}, + {0x9012b, 0x0}, + {0x9012c, 0x0}, + {0x9012d, 0x0}, + {0x9012e, 0x0}, + {0x9012f, 0x0}, + {0x90130, 0x0}, + {0x90131, 0x0}, + {0x90132, 0x0}, + {0x90133, 0x0}, + {0x90134, 0x0}, + {0x90135, 0x0}, + {0x90136, 0x0}, + {0x90137, 0x0}, + {0x90138, 0x0}, + {0x90139, 0x0}, + {0x9013a, 0x0}, + {0x9013b, 0x0}, + {0x9013c, 0x0}, + {0x9013d, 0x0}, + {0x9013e, 0x0}, + {0x9013f, 0x0}, + {0x90140, 0x0}, + {0x90141, 0x0}, + {0x90142, 0x0}, + {0x90143, 0x0}, + {0x90144, 0x0}, + {0x90145, 0x0}, + {0x90146, 0x0}, + {0x90147, 0x0}, + {0x90148, 0x0}, + {0x90149, 0x0}, + {0x9014a, 0x0}, + {0x9014b, 0x0}, + {0x9014c, 0x0}, + {0x9014d, 0x0}, + {0x9014e, 0x0}, + {0x9014f, 0x0}, + {0x90150, 0x0}, + {0x90151, 0x0}, + {0x90152, 0x0}, + {0x90153, 0x0}, + {0x90154, 0x0}, + {0x90155, 0x0}, + {0x90156, 0x0}, + {0x90157, 0x0}, + {0x90158, 0x0}, + {0x90159, 0x0}, + {0x9015a, 0x0}, + {0x9015b, 0x0}, + {0x9015c, 0x0}, + {0x9015d, 0x0}, + {0x9015e, 0x0}, + {0x9015f, 0x0}, + {0x90160, 0x0}, + {0x90161, 0x0}, + {0x90162, 0x0}, + {0x90163, 0x0}, + {0x90164, 0x0}, + {0x90165, 0x0}, + {0x90166, 0x0}, + {0x90167, 0x0}, + {0x90168, 0x0}, + {0x90169, 0x0}, + {0x9016a, 0x0}, + {0x9016b, 0x0}, + {0x9016c, 0x0}, + {0x9016d, 0x0}, + {0x9016e, 0x0}, + {0x9016f, 0x0}, + {0x90170, 0x0}, + {0x90171, 0x0}, + {0x90172, 0x0}, + {0x90173, 0x0}, + {0x90174, 0x0}, + {0x90175, 0x0}, + {0x90176, 0x0}, + {0x90177, 0x0}, + {0x90178, 0x0}, + {0x90179, 0x0}, + {0x9017a, 0x0}, + {0x9017b, 0x0}, + {0x9017c, 0x0}, + {0x9017d, 0x0}, + {0x9017e, 0x0}, + {0x9017f, 0x0}, + {0x90180, 0x0}, + {0x90181, 0x0}, + {0x90182, 0x0}, + {0x90183, 0x0}, + {0x90184, 0x0}, + {0x90006, 0x0}, + {0x90007, 0x0}, + {0x90008, 0x0}, + {0x90009, 0x0}, + {0x9000a, 0x0}, + {0x9000b, 0x0}, + {0xd00e7, 0x0}, + {0x90017, 0x0}, + {0x9001f, 0x0}, + {0x90026, 0x0}, + {0x400d0, 0x0}, + {0x400d1, 0x0}, + {0x400d2, 0x0}, + {0x400d3, 0x0}, + {0x400d4, 0x0}, + {0x400d5, 0x0}, + {0x400d6, 0x0}, + {0x400d7, 0x0}, + {0x200be, 0x0}, + {0x2000b, 0x0}, + {0x2000c, 0x0}, + {0x2000d, 0x0}, + {0x2000e, 0x0}, + {0x9000c, 0x0}, + {0x9000d, 0x0}, + {0x9000e, 0x0}, + {0x9000f, 0x0}, + {0x90010, 0x0}, + {0x90011, 0x0}, + {0x90012, 0x0}, + {0x90013, 0x0}, + {0x20010, 0x0}, + {0x20011, 0x0}, + {0x40080, 0x0}, + {0x40081, 0x0}, + {0x40082, 0x0}, + {0x40083, 0x0}, + {0x40084, 0x0}, + {0x40085, 0x0}, + {0x400fd, 0x0}, + {0x400f1, 0x0}, + {0x10011, 0x0}, + {0x10012, 0x0}, + {0x10013, 0x0}, + {0x10018, 0x0}, + {0x10002, 0x0}, + {0x100b2, 0x0}, + {0x101b4, 0x0}, + {0x102b4, 0x0}, + {0x103b4, 0x0}, + {0x104b4, 0x0}, + {0x105b4, 0x0}, + {0x106b4, 0x0}, + {0x107b4, 0x0}, + {0x108b4, 0x0}, + {0x11011, 0x0}, + {0x11012, 0x0}, + {0x11013, 0x0}, + {0x11018, 0x0}, + {0x11002, 0x0}, + {0x110b2, 0x0}, + {0x111b4, 0x0}, + {0x112b4, 0x0}, + {0x113b4, 0x0}, + {0x114b4, 0x0}, + {0x115b4, 0x0}, + {0x116b4, 0x0}, + {0x117b4, 0x0}, + {0x118b4, 0x0}, + {0x20089, 0x0}, + {0xc0080, 0x0}, + {0x200cb, 0x0}, + {0x10068, 0x0}, + {0x10069, 0x0}, + {0x10168, 0x0}, + {0x10169, 0x0}, + {0x10268, 0x0}, + {0x10269, 0x0}, + {0x10368, 0x0}, + {0x10369, 0x0}, + {0x10468, 0x0}, + {0x10469, 0x0}, + {0x10568, 0x0}, + {0x10569, 0x0}, + {0x10668, 0x0}, + {0x10669, 0x0}, + {0x10768, 0x0}, + {0x10769, 0x0}, + {0x10868, 0x0}, + {0x10869, 0x0}, + {0x100aa, 0x0}, + {0x10062, 0x0}, + {0x10001, 0x0}, + {0x100a0, 0x0}, + {0x100a1, 0x0}, + {0x100a2, 0x0}, + {0x100a3, 0x0}, + {0x100a4, 0x0}, + {0x100a5, 0x0}, + {0x100a6, 0x0}, + {0x100a7, 0x0}, + {0x11068, 0x0}, + {0x11069, 0x0}, + {0x11168, 0x0}, + {0x11169, 0x0}, + {0x11268, 0x0}, + {0x11269, 0x0}, + {0x11368, 0x0}, + {0x11369, 0x0}, + {0x11468, 0x0}, + {0x11469, 0x0}, + {0x11568, 0x0}, + {0x11569, 0x0}, + {0x11668, 0x0}, + {0x11669, 0x0}, + {0x11768, 0x0}, + {0x11769, 0x0}, + {0x11868, 0x0}, + {0x11869, 0x0}, + {0x110aa, 0x0}, + {0x11062, 0x0}, + {0x11001, 0x0}, + {0x110a0, 0x0}, + {0x110a1, 0x0}, + {0x110a2, 0x0}, + {0x110a3, 0x0}, + {0x110a4, 0x0}, + {0x110a5, 0x0}, + {0x110a6, 0x0}, + {0x110a7, 0x0}, + {0x80, 0x0}, + {0x1080, 0x0}, + {0x2080, 0x0}, + {0x10020, 0x0}, + {0x10080, 0x0}, + {0x10081, 0x0}, + {0x100d0, 0x0}, + {0x100d1, 0x0}, + {0x1008c, 0x0}, + {0x1008d, 0x0}, + {0x10180, 0x0}, + {0x10181, 0x0}, + {0x101d0, 0x0}, + {0x101d1, 0x0}, + {0x1018c, 0x0}, + {0x1018d, 0x0}, + {0x100c0, 0x0}, + {0x100c1, 0x0}, + {0x101c0, 0x0}, + {0x101c1, 0x0}, + {0x102c0, 0x0}, + {0x102c1, 0x0}, + {0x103c0, 0x0}, + {0x103c1, 0x0}, + {0x104c0, 0x0}, + {0x104c1, 0x0}, + {0x105c0, 0x0}, + {0x105c1, 0x0}, + {0x106c0, 0x0}, + {0x106c1, 0x0}, + {0x107c0, 0x0}, + {0x107c1, 0x0}, + {0x108c0, 0x0}, + {0x108c1, 0x0}, + {0x100ae, 0x0}, + {0x100af, 0x0}, + {0x11020, 0x0}, + {0x11080, 0x0}, + {0x11081, 0x0}, + {0x110d0, 0x0}, + {0x110d1, 0x0}, + {0x1108c, 0x0}, + {0x1108d, 0x0}, + {0x11180, 0x0}, + {0x11181, 0x0}, + {0x111d0, 0x0}, + {0x111d1, 0x0}, + {0x1118c, 0x0}, + {0x1118d, 0x0}, + {0x110c0, 0x0}, + {0x110c1, 0x0}, + {0x111c0, 0x0}, + {0x111c1, 0x0}, + {0x112c0, 0x0}, + {0x112c1, 0x0}, + {0x113c0, 0x0}, + {0x113c1, 0x0}, + {0x114c0, 0x0}, + {0x114c1, 0x0}, + {0x115c0, 0x0}, + {0x115c1, 0x0}, + {0x116c0, 0x0}, + {0x116c1, 0x0}, + {0x117c0, 0x0}, + {0x117c1, 0x0}, + {0x118c0, 0x0}, + {0x118c1, 0x0}, + {0x110ae, 0x0}, + {0x110af, 0x0}, + {0x90201, 0x0}, + {0x90202, 0x0}, + {0x90203, 0x0}, + {0x90205, 0x0}, + {0x90206, 0x0}, + {0x90207, 0x0}, + {0x90208, 0x0}, + {0x20020, 0x0}, + {0x20077, 0x0}, + {0x20072, 0x0}, + {0x20073, 0x0}, + {0x400c0, 0x0}, + {0x10040, 0x0}, + {0x10140, 0x0}, + {0x10240, 0x0}, + {0x10340, 0x0}, + {0x10440, 0x0}, + {0x10540, 0x0}, + {0x10640, 0x0}, + {0x10740, 0x0}, + {0x10840, 0x0}, + {0x11040, 0x0}, + {0x11140, 0x0}, + {0x11240, 0x0}, + {0x11340, 0x0}, + {0x11440, 0x0}, + {0x11540, 0x0}, + {0x11640, 0x0}, + {0x11740, 0x0}, + {0x11840, 0x0}, + +}; + +/* P0 message block parameter for training firmware */ +static struct dram_cfg_param ddr_fsp0_cfg[] = { + {0xd0000, 0x0}, + {0x54003, 0xe94}, + {0x54004, 0x4}, + {0x54006, 0x15}, + {0x54008, 0x131f}, + {0x54009, 0xc8}, + {0x5400b, 0x4}, + {0x5400d, 0x100}, + {0x5400f, 0x100}, + {0x54012, 0x110}, + {0x54019, 0x36e4}, + {0x5401a, 0xf2}, + {0x5401b, 0x1146}, + {0x5401c, 0x1108}, + {0x5401e, 0x4}, + {0x5401f, 0x36e4}, + {0x54020, 0xf2}, + {0x54021, 0x1146}, + {0x54022, 0x1108}, + {0x54024, 0x4}, + {0x54032, 0xe400}, + {0x54033, 0xf236}, + {0x54034, 0x4600}, + {0x54035, 0x811}, + {0x54036, 0x11}, + {0x54037, 0x400}, + {0x54038, 0xe400}, + {0x54039, 0xf236}, + {0x5403a, 0x4600}, + {0x5403b, 0x811}, + {0x5403c, 0x11}, + {0x5403d, 0x400}, + {0xd0000, 0x1} +}; + +/* P0 2D message block parameter for training firmware */ +static struct dram_cfg_param ddr_fsp0_2d_cfg[] = { + {0xd0000, 0x0}, + {0x54003, 0xe94}, + {0x54004, 0x4}, + {0x54006, 0x15}, + {0x54008, 0x61}, + {0x54009, 0xc8}, + {0x5400b, 0x4}, + {0x5400d, 0x100}, + {0x5400f, 0x100}, + {0x54010, 0x2080}, + {0x54012, 0x110}, + {0x54019, 0x36e4}, + {0x5401a, 0xf2}, + {0x5401b, 0x1146}, + {0x5401c, 0x1108}, + {0x5401e, 0x4}, + {0x5401f, 0x36e4}, + {0x54020, 0xf2}, + {0x54021, 0x1146}, + {0x54022, 0x1108}, + {0x54024, 0x4}, + {0x54032, 0xe400}, + {0x54033, 0xf236}, + {0x54034, 0x4600}, + {0x54035, 0x811}, + {0x54036, 0x11}, + {0x54037, 0x400}, + {0x54038, 0xe400}, + {0x54039, 0xf236}, + {0x5403a, 0x4600}, + {0x5403b, 0x811}, + {0x5403c, 0x11}, + {0x5403d, 0x400}, + {0xd0000, 0x1} +}; + +/* DRAM PHY init engine image */ +static struct dram_cfg_param ddr_phy_pie[] = { + {0xd0000, 0x0}, + {0x90000, 0x10}, + {0x90001, 0x400}, + {0x90002, 0x10e}, + {0x90003, 0x0}, + {0x90004, 0x0}, + {0x90005, 0x8}, + {0x90029, 0xb}, + {0x9002a, 0x480}, + {0x9002b, 0x109}, + {0x9002c, 0x8}, + {0x9002d, 0x448}, + {0x9002e, 0x139}, + {0x9002f, 0x8}, + {0x90030, 0x478}, + {0x90031, 0x109}, + {0x90032, 0x0}, + {0x90033, 0xe8}, + {0x90034, 0x109}, + {0x90035, 0x2}, + {0x90036, 0x10}, + {0x90037, 0x139}, + {0x90038, 0xb}, + {0x90039, 0x7c0}, + {0x9003a, 0x139}, + {0x9003b, 0x44}, + {0x9003c, 0x633}, + {0x9003d, 0x159}, + {0x9003e, 0x14f}, + {0x9003f, 0x630}, + {0x90040, 0x159}, + {0x90041, 0x47}, + {0x90042, 0x633}, + {0x90043, 0x149}, + {0x90044, 0x4f}, + {0x90045, 0x633}, + {0x90046, 0x179}, + {0x90047, 0x8}, + {0x90048, 0xe0}, + {0x90049, 0x109}, + {0x9004a, 0x0}, + {0x9004b, 0x7c8}, + {0x9004c, 0x109}, + {0x9004d, 0x0}, + {0x9004e, 0x1}, + {0x9004f, 0x8}, + {0x90050, 0x30}, + {0x90051, 0x65a}, + {0x90052, 0x9}, + {0x90053, 0x0}, + {0x90054, 0x45a}, + {0x90055, 0x9}, + {0x90056, 0x0}, + {0x90057, 0x448}, + {0x90058, 0x109}, + {0x90059, 0x40}, + {0x9005a, 0x633}, + {0x9005b, 0x179}, + {0x9005c, 0x1}, + {0x9005d, 0x618}, + {0x9005e, 0x109}, + {0x9005f, 0x40c0}, + {0x90060, 0x633}, + {0x90061, 0x149}, + {0x90062, 0x8}, + {0x90063, 0x4}, + {0x90064, 0x48}, + {0x90065, 0x4040}, + {0x90066, 0x633}, + {0x90067, 0x149}, + {0x90068, 0x0}, + {0x90069, 0x4}, + {0x9006a, 0x48}, + {0x9006b, 0x40}, + {0x9006c, 0x633}, + {0x9006d, 0x149}, + {0x9006e, 0x0}, + {0x9006f, 0x658}, + {0x90070, 0x109}, + {0x90071, 0x10}, + {0x90072, 0x4}, + {0x90073, 0x18}, + {0x90074, 0x0}, + {0x90075, 0x4}, + {0x90076, 0x78}, + {0x90077, 0x549}, + {0x90078, 0x633}, + {0x90079, 0x159}, + {0x9007a, 0xd49}, + {0x9007b, 0x633}, + {0x9007c, 0x159}, + {0x9007d, 0x94a}, + {0x9007e, 0x633}, + {0x9007f, 0x159}, + {0x90080, 0x441}, + {0x90081, 0x633}, + {0x90082, 0x149}, + {0x90083, 0x42}, + {0x90084, 0x633}, + {0x90085, 0x149}, + {0x90086, 0x1}, + {0x90087, 0x633}, + {0x90088, 0x149}, + {0x90089, 0x0}, + {0x9008a, 0xe0}, + {0x9008b, 0x109}, + {0x9008c, 0xa}, + {0x9008d, 0x10}, + {0x9008e, 0x109}, + {0x9008f, 0x9}, + {0x90090, 0x3c0}, + {0x90091, 0x149}, + {0x90092, 0x9}, + {0x90093, 0x3c0}, + {0x90094, 0x159}, + {0x90095, 0x18}, + {0x90096, 0x10}, + {0x90097, 0x109}, + {0x90098, 0x0}, + {0x90099, 0x3c0}, + {0x9009a, 0x109}, + {0x9009b, 0x18}, + {0x9009c, 0x4}, + {0x9009d, 0x48}, + {0x9009e, 0x18}, + {0x9009f, 0x4}, + {0x900a0, 0x58}, + {0x900a1, 0xb}, + {0x900a2, 0x10}, + {0x900a3, 0x109}, + {0x900a4, 0x1}, + {0x900a5, 0x10}, + {0x900a6, 0x109}, + {0x900a7, 0x5}, + {0x900a8, 0x7c0}, + {0x900a9, 0x109}, + {0x40000, 0x811}, + {0x40020, 0x880}, + {0x40040, 0x0}, + {0x40060, 0x0}, + {0x40001, 0x4008}, + {0x40021, 0x83}, + {0x40041, 0x4f}, + {0x40061, 0x0}, + {0x40002, 0x4040}, + {0x40022, 0x83}, + {0x40042, 0x51}, + {0x40062, 0x0}, + {0x40003, 0x811}, + {0x40023, 0x880}, + {0x40043, 0x0}, + {0x40063, 0x0}, + {0x40004, 0x720}, + {0x40024, 0xf}, + {0x40044, 0x1740}, + {0x40064, 0x0}, + {0x40005, 0x16}, + {0x40025, 0x83}, + {0x40045, 0x4b}, + {0x40065, 0x0}, + {0x40006, 0x716}, + {0x40026, 0xf}, + {0x40046, 0x2001}, + {0x40066, 0x0}, + {0x40007, 0x716}, + {0x40027, 0xf}, + {0x40047, 0x2800}, + {0x40067, 0x0}, + {0x40008, 0x716}, + {0x40028, 0xf}, + {0x40048, 0xf00}, + {0x40068, 0x0}, + {0x40009, 0x720}, + {0x40029, 0xf}, + {0x40049, 0x1400}, + {0x40069, 0x0}, + {0x4000a, 0xe08}, + {0x4002a, 0xc15}, + {0x4004a, 0x0}, + {0x4006a, 0x0}, + {0x4000b, 0x625}, + {0x4002b, 0x15}, + {0x4004b, 0x0}, + {0x4006b, 0x0}, + {0x4000c, 0x4028}, + {0x4002c, 0x80}, + {0x4004c, 0x0}, + {0x4006c, 0x0}, + {0x4000d, 0xe08}, + {0x4002d, 0xc1a}, + {0x4004d, 0x0}, + {0x4006d, 0x0}, + {0x4000e, 0x625}, + {0x4002e, 0x1a}, + {0x4004e, 0x0}, + {0x4006e, 0x0}, + {0x4000f, 0x4040}, + {0x4002f, 0x80}, + {0x4004f, 0x0}, + {0x4006f, 0x0}, + {0x40010, 0x2604}, + {0x40030, 0x15}, + {0x40050, 0x0}, + {0x40070, 0x0}, + {0x40011, 0x708}, + {0x40031, 0x5}, + {0x40051, 0x0}, + {0x40071, 0x2002}, + {0x40012, 0x8}, + {0x40032, 0x80}, + {0x40052, 0x0}, + {0x40072, 0x0}, + {0x40013, 0x2604}, + {0x40033, 0x1a}, + {0x40053, 0x0}, + {0x40073, 0x0}, + {0x40014, 0x708}, + {0x40034, 0xa}, + {0x40054, 0x0}, + {0x40074, 0x2002}, + {0x40015, 0x4040}, + {0x40035, 0x80}, + {0x40055, 0x0}, + {0x40075, 0x0}, + {0x40016, 0x60a}, + {0x40036, 0x15}, + {0x40056, 0x1200}, + {0x40076, 0x0}, + {0x40017, 0x61a}, + {0x40037, 0x15}, + {0x40057, 0x1300}, + {0x40077, 0x0}, + {0x40018, 0x60a}, + {0x40038, 0x1a}, + {0x40058, 0x1200}, + {0x40078, 0x0}, + {0x40019, 0x642}, + {0x40039, 0x1a}, + {0x40059, 0x1300}, + {0x40079, 0x0}, + {0x4001a, 0x4808}, + {0x4003a, 0x880}, + {0x4005a, 0x0}, + {0x4007a, 0x0}, + {0x900aa, 0x0}, + {0x900ab, 0x790}, + {0x900ac, 0x11a}, + {0x900ad, 0x8}, + {0x900ae, 0x7aa}, + {0x900af, 0x2a}, + {0x900b0, 0x10}, + {0x900b1, 0x7b2}, + {0x900b2, 0x2a}, + {0x900b3, 0x0}, + {0x900b4, 0x7c8}, + {0x900b5, 0x109}, + {0x900b6, 0x10}, + {0x900b7, 0x10}, + {0x900b8, 0x109}, + {0x900b9, 0x10}, + {0x900ba, 0x2a8}, + {0x900bb, 0x129}, + {0x900bc, 0x8}, + {0x900bd, 0x370}, + {0x900be, 0x129}, + {0x900bf, 0xa}, + {0x900c0, 0x3c8}, + {0x900c1, 0x1a9}, + {0x900c2, 0xc}, + {0x900c3, 0x408}, + {0x900c4, 0x199}, + {0x900c5, 0x14}, + {0x900c6, 0x790}, + {0x900c7, 0x11a}, + {0x900c8, 0x8}, + {0x900c9, 0x4}, + {0x900ca, 0x18}, + {0x900cb, 0xe}, + {0x900cc, 0x408}, + {0x900cd, 0x199}, + {0x900ce, 0x8}, + {0x900cf, 0x8568}, + {0x900d0, 0x108}, + {0x900d1, 0x18}, + {0x900d2, 0x790}, + {0x900d3, 0x16a}, + {0x900d4, 0x8}, + {0x900d5, 0x1d8}, + {0x900d6, 0x169}, + {0x900d7, 0x10}, + {0x900d8, 0x8558}, + {0x900d9, 0x168}, + {0x900da, 0x1ff8}, + {0x900db, 0x85a8}, + {0x900dc, 0x1e8}, + {0x900dd, 0x50}, + {0x900de, 0x798}, + {0x900df, 0x16a}, + {0x900e0, 0x60}, + {0x900e1, 0x7a0}, + {0x900e2, 0x16a}, + {0x900e3, 0x8}, + {0x900e4, 0x8310}, + {0x900e5, 0x168}, + {0x900e6, 0x8}, + {0x900e7, 0xa310}, + {0x900e8, 0x168}, + {0x900e9, 0xa}, + {0x900ea, 0x408}, + {0x900eb, 0x169}, + {0x900ec, 0x6e}, + {0x900ed, 0x0}, + {0x900ee, 0x68}, + {0x900ef, 0x0}, + {0x900f0, 0x408}, + {0x900f1, 0x169}, + {0x900f2, 0x0}, + {0x900f3, 0x8310}, + {0x900f4, 0x168}, + {0x900f5, 0x0}, + {0x900f6, 0xa310}, + {0x900f7, 0x168}, + {0x900f8, 0x1ff8}, + {0x900f9, 0x85a8}, + {0x900fa, 0x1e8}, + {0x900fb, 0x68}, + {0x900fc, 0x798}, + {0x900fd, 0x16a}, + {0x900fe, 0x78}, + {0x900ff, 0x7a0}, + {0x90100, 0x16a}, + {0x90101, 0x68}, + {0x90102, 0x790}, + {0x90103, 0x16a}, + {0x90104, 0x8}, + {0x90105, 0x8b10}, + {0x90106, 0x168}, + {0x90107, 0x8}, + {0x90108, 0xab10}, + {0x90109, 0x168}, + {0x9010a, 0xa}, + {0x9010b, 0x408}, + {0x9010c, 0x169}, + {0x9010d, 0x58}, + {0x9010e, 0x0}, + {0x9010f, 0x68}, + {0x90110, 0x0}, + {0x90111, 0x408}, + {0x90112, 0x169}, + {0x90113, 0x0}, + {0x90114, 0x8b10}, + {0x90115, 0x168}, + {0x90116, 0x1}, + {0x90117, 0xab10}, + {0x90118, 0x168}, + {0x90119, 0x0}, + {0x9011a, 0x1d8}, + {0x9011b, 0x169}, + {0x9011c, 0x80}, + {0x9011d, 0x790}, + {0x9011e, 0x16a}, + {0x9011f, 0x18}, + {0x90120, 0x7aa}, + {0x90121, 0x6a}, + {0x90122, 0xa}, + {0x90123, 0x0}, + {0x90124, 0x1e9}, + {0x90125, 0x8}, + {0x90126, 0x8080}, + {0x90127, 0x108}, + {0x90128, 0xf}, + {0x90129, 0x408}, + {0x9012a, 0x169}, + {0x9012b, 0xc}, + {0x9012c, 0x0}, + {0x9012d, 0x68}, + {0x9012e, 0x9}, + {0x9012f, 0x0}, + {0x90130, 0x1a9}, + {0x90131, 0x0}, + {0x90132, 0x408}, + {0x90133, 0x169}, + {0x90134, 0x0}, + {0x90135, 0x8080}, + {0x90136, 0x108}, + {0x90137, 0x8}, + {0x90138, 0x7aa}, + {0x90139, 0x6a}, + {0x9013a, 0x0}, + {0x9013b, 0x8568}, + {0x9013c, 0x108}, + {0x9013d, 0xb7}, + {0x9013e, 0x790}, + {0x9013f, 0x16a}, + {0x90140, 0x1f}, + {0x90141, 0x0}, + {0x90142, 0x68}, + {0x90143, 0x8}, + {0x90144, 0x8558}, + {0x90145, 0x168}, + {0x90146, 0xf}, + {0x90147, 0x408}, + {0x90148, 0x169}, + {0x90149, 0xd}, + {0x9014a, 0x0}, + {0x9014b, 0x68}, + {0x9014c, 0x0}, + {0x9014d, 0x408}, + {0x9014e, 0x169}, + {0x9014f, 0x0}, + {0x90150, 0x8558}, + {0x90151, 0x168}, + {0x90152, 0x8}, + {0x90153, 0x3c8}, + {0x90154, 0x1a9}, + {0x90155, 0x3}, + {0x90156, 0x370}, + {0x90157, 0x129}, + {0x90158, 0x20}, + {0x90159, 0x2aa}, + {0x9015a, 0x9}, + {0x9015b, 0x8}, + {0x9015c, 0xe8}, + {0x9015d, 0x109}, + {0x9015e, 0x0}, + {0x9015f, 0x8140}, + {0x90160, 0x10c}, + {0x90161, 0x10}, + {0x90162, 0x8138}, + {0x90163, 0x104}, + {0x90164, 0x8}, + {0x90165, 0x448}, + {0x90166, 0x109}, + {0x90167, 0xf}, + {0x90168, 0x7c0}, + {0x90169, 0x109}, + {0x9016a, 0x0}, + {0x9016b, 0xe8}, + {0x9016c, 0x109}, + {0x9016d, 0x47}, + {0x9016e, 0x630}, + {0x9016f, 0x109}, + {0x90170, 0x8}, + {0x90171, 0x618}, + {0x90172, 0x109}, + {0x90173, 0x8}, + {0x90174, 0xe0}, + {0x90175, 0x109}, + {0x90176, 0x0}, + {0x90177, 0x7c8}, + {0x90178, 0x109}, + {0x90179, 0x8}, + {0x9017a, 0x8140}, + {0x9017b, 0x10c}, + {0x9017c, 0x0}, + {0x9017d, 0x478}, + {0x9017e, 0x109}, + {0x9017f, 0x0}, + {0x90180, 0x1}, + {0x90181, 0x8}, + {0x90182, 0x8}, + {0x90183, 0x4}, + {0x90184, 0x0}, + {0x90006, 0x8}, + {0x90007, 0x7c8}, + {0x90008, 0x109}, + {0x90009, 0x0}, + {0x9000a, 0x400}, + {0x9000b, 0x106}, + {0xd00e7, 0x400}, + {0x90017, 0x0}, + {0x9001f, 0x2b}, + {0x90026, 0x69}, + {0x400d0, 0x0}, + {0x400d1, 0x101}, + {0x400d2, 0x105}, + {0x400d3, 0x107}, + {0x400d4, 0x10f}, + {0x400d5, 0x202}, + {0x400d6, 0x20a}, + {0x400d7, 0x20b}, + {0x2003a, 0x2}, + {0x200be, 0x3}, + {0x2000b, 0x75}, + {0x2000c, 0xe9}, + {0x2000d, 0x91c}, + {0x2000e, 0x2c}, + {0x9000c, 0x0}, + {0x9000d, 0x173}, + {0x9000e, 0x60}, + {0x9000f, 0x6110}, + {0x90010, 0x2152}, + {0x90011, 0xdfbd}, + {0x90012, 0x2060}, + {0x90013, 0x6152}, + {0x20010, 0x5a}, + {0x20011, 0x3}, + {0x40080, 0xe0}, + {0x40081, 0x12}, + {0x40082, 0xe0}, + {0x40083, 0x12}, + {0x40084, 0xe0}, + {0x40085, 0x12}, + {0x400fd, 0xf}, + {0x400f1, 0xe}, + {0x10011, 0x1}, + {0x10012, 0x1}, + {0x10013, 0x180}, + {0x10018, 0x1}, + {0x10002, 0x6209}, + {0x100b2, 0x1}, + {0x101b4, 0x1}, + {0x102b4, 0x1}, + {0x103b4, 0x1}, + {0x104b4, 0x1}, + {0x105b4, 0x1}, + {0x106b4, 0x1}, + {0x107b4, 0x1}, + {0x108b4, 0x1}, + {0x11011, 0x1}, + {0x11012, 0x1}, + {0x11013, 0x180}, + {0x11018, 0x1}, + {0x11002, 0x6209}, + {0x110b2, 0x1}, + {0x111b4, 0x1}, + {0x112b4, 0x1}, + {0x113b4, 0x1}, + {0x114b4, 0x1}, + {0x115b4, 0x1}, + {0x116b4, 0x1}, + {0x117b4, 0x1}, + {0x118b4, 0x1}, + {0x20089, 0x1}, + {0x20088, 0x19}, + {0xc0080, 0x0}, + {0xd0000, 0x1}, + +}; + +static struct dram_fsp_msg ddr_dram_fsp_msg[] = { + { + /* P0 3733mts 1D */ + .drate = 3733, + .fw_type = FW_1D_IMAGE, + .fsp_cfg = ddr_fsp0_cfg, + .fsp_cfg_num = ARRAY_SIZE(ddr_fsp0_cfg), + + }, + + { + /* P0 3733mts 2D */ + .drate = 3733, + .fw_type = FW_2D_IMAGE, + .fsp_cfg = ddr_fsp0_2d_cfg, + .fsp_cfg_num = ARRAY_SIZE(ddr_fsp0_2d_cfg), + }, + +}; + +/* ddr timing config params */ +struct dram_timing_info dram_timing = { + .ddrc_cfg = ddr_ddrc_cfg, + .ddrc_cfg_num = ARRAY_SIZE(ddr_ddrc_cfg), + .ddrphy_cfg = ddr_ddrphy_cfg, + .ddrphy_cfg_num = ARRAY_SIZE(ddr_ddrphy_cfg), + .fsp_msg = ddr_dram_fsp_msg, + .fsp_msg_num = ARRAY_SIZE(ddr_dram_fsp_msg), + .ddrphy_trained_csr = ddr_ddrphy_trained_csr, + .ddrphy_trained_csr_num = ARRAY_SIZE(ddr_ddrphy_trained_csr), + .ddrphy_pie = ddr_phy_pie, + .ddrphy_pie_num = ARRAY_SIZE(ddr_phy_pie), + .fsp_table = { 3733, }, + .fsp_cfg = ddr_dram_fsp_cfg, + .fsp_cfg_num = ARRAY_SIZE(ddr_dram_fsp_cfg), +}; diff --git a/board/phytec/phycore_imx93/phycore-imx93.c b/board/phytec/phycore_imx93/phycore-imx93.c new file mode 100644 index 00000000000..085c8e195a6 --- /dev/null +++ b/board/phytec/phycore_imx93/phycore-imx93.c @@ -0,0 +1,42 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2023 PHYTEC Messtechnik GmbH + * Author: Christoph Stoidner <c.stoidner@phytec.de> + * Copyright (C) 2024 Mathieu Othacehe <m.othacehe@gmail.com> + */ + +#include <asm/arch-imx9/ccm_regs.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch-imx9/imx93_pins.h> +#include <asm/arch/clock.h> +#include <asm/global_data.h> +#include <asm/mach-imx/boot_mode.h> +#include <env.h> + +DECLARE_GLOBAL_DATA_PTR; + +int board_init(void) +{ + return 0; +} + +int board_mmc_get_env_dev(int devno) +{ + return devno; +} + +int board_late_init(void) +{ + switch (get_boot_device()) { + case SD2_BOOT: + env_set_ulong("mmcdev", 1); + break; + case MMC1_BOOT: + env_set_ulong("mmcdev", 0); + break; + default: + break; + } + + return 0; +} diff --git a/board/phytec/phycore_imx93/phycore_imx93.env b/board/phytec/phycore_imx93/phycore_imx93.env new file mode 100644 index 00000000000..27bfadfa140 --- /dev/null +++ b/board/phytec/phycore_imx93/phycore_imx93.env @@ -0,0 +1,73 @@ +/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */ + +image=Image +console=ttyLP0 +fdt_addr=0x83000000 +fdto_addr=0x830c0000 +bootenv_addr=0x83500000 +fdt_file=CONFIG_DEFAULT_FDT_FILE +ip_dyn=yes +bootenv=bootenv.txt +mmc_load_bootenv=fatload mmc ${mmcdev}:${mmcpart} ${bootenv_addr} ${bootenv} +mmcdev=CONFIG_SYS_MMC_ENV_DEV +mmcpart=1 +mmcroot=2 +mmcautodetect=yes +mmcargs=setenv bootargs console=${console},${baudrate} earlycon + root=/dev/mmcblk${mmcdev}p${mmcroot} ${raucargs} rootwait rw +loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image} +loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file} +mmc_load_overlay=fatload mmc ${mmcdev}:${mmcpart} ${fdto_addr} ${overlay} +mmc_apply_overlays= + fdt address ${fdt_addr}; + for overlay in ${overlays}; + do; + if run mmc_load_overlay; then + fdt resize ${filesize}; + fdt apply ${fdto_addr}; + fi; + done; +mmcboot= + echo Booting from mmc ...; + if run mmc_load_bootenv; then + env import -t ${bootenv_addr} ${filesize}; + fi; + run mmcargs; + if run loadfdt; then + run mmc_apply_overlays; + booti ${loadaddr} - ${fdt_addr}; + else + echo WARN: Cannot load the DT; + fi; +nfsroot=/nfs +netargs=setenv bootargs console=${console},${baudrate} earlycon + root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp +net_load_bootenv=${get_cmd} ${bootenv_addr} ${bootenv} +net_load_overlay=${get_cmd} ${fdto_addr} ${overlay} +net_apply_overlays= + fdt address ${fdt_addr}; + for overlay in ${overlays}; + do; + if run net_load_overlay; then + fdt resize ${filesize}; + fdt apply ${fdto_addr}; + fi; + done; +netboot= + echo Booting from net ...; + run netargs; + if test ${ip_dyn} = yes; then + setenv get_cmd dhcp; + else + setenv get_cmd tftp; + fi; + if run net_load_bootenv; then + env import -t ${bootenv_addr} ${filesize}; + fi; + ${get_cmd} ${loadaddr} ${image}; + if ${get_cmd} ${fdt_addr} ${fdt_file}; then + run net_apply_overlays; + booti ${loadaddr} - ${fdt_addr}; + else + echo WARN: Cannot load the DT; + fi; diff --git a/board/phytec/phycore_imx93/spl.c b/board/phytec/phycore_imx93/spl.c new file mode 100644 index 00000000000..da4b9e53594 --- /dev/null +++ b/board/phytec/phycore_imx93/spl.c @@ -0,0 +1,148 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2023 PHYTEC Messtechnik GmbH + * Author: Christoph Stoidner <c.stoidner@phytec.de> + * Copyright (C) 2024 Mathieu Othacehe <m.othacehe@gmail.com> + */ + +#include <asm/arch/clock.h> +#include <asm/arch/ddr.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/trdc.h> +#include <asm/mach-imx/boot_mode.h> +#include <asm/sections.h> +#include <hang.h> +#include <init.h> +#include <log.h> +#include <power/pmic.h> +#include <power/pca9450.h> +#include <spl.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* + * Will be part of drivers/power/regulator/pca9450.c + * when pca9451a support is added. + */ +#define PCA9450_REG_PWRCTRL_TOFF_DEB BIT(5) + +int spl_board_boot_device(enum boot_device boot_dev_spl) +{ + return BOOT_DEVICE_BOOTROM; +} + +void spl_board_init(void) +{ + puts("Normal Boot\n"); +} + +void spl_dram_init(void) +{ + ddr_init(&dram_timing); +} + +int power_init_board(void) +{ + struct udevice *dev; + int ret; + unsigned int val = 0; + + ret = pmic_get("pmic@25", &dev); + if (ret == -ENODEV) { + puts("No pca9450@25\n"); + return 0; + } + + if (ret != 0) + return ret; + + /* BUCKxOUT_DVS0/1 control BUCK123 output */ + pmic_reg_write(dev, PCA9450_BUCK123_DVS, 0x29); + + /* enable DVS control through PMIC_STBY_REQ */ + pmic_reg_write(dev, PCA9450_BUCK1CTRL, 0x59); + + ret = pmic_reg_read(dev, PCA9450_PWR_CTRL); + if (ret < 0) + return ret; + val = ret; + + if (IS_ENABLED(CONFIG_IMX9_LOW_DRIVE_MODE)) { + /* 0.8v for Low drive mode */ + if (val & PCA9450_REG_PWRCTRL_TOFF_DEB) { + pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, 0x0c); + pmic_reg_write(dev, PCA9450_BUCK3OUT_DVS0, 0x0c); + } else { + pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, 0x10); + pmic_reg_write(dev, PCA9450_BUCK3OUT_DVS0, 0x10); + } + } else { + /* 0.9v for Over drive mode */ + if (val & PCA9450_REG_PWRCTRL_TOFF_DEB) { + pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, 0x14); + pmic_reg_write(dev, PCA9450_BUCK3OUT_DVS0, 0x14); + } else { + pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS0, 0x18); + pmic_reg_write(dev, PCA9450_BUCK3OUT_DVS0, 0x18); + } + } + + /* set standby voltage to 0.65v */ + if (val & PCA9450_REG_PWRCTRL_TOFF_DEB) + pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS1, 0x0); + else + pmic_reg_write(dev, PCA9450_BUCK1OUT_DVS1, 0x4); + + /* I2C_LT_EN*/ + pmic_reg_write(dev, 0xa, 0x3); + + return 0; +} + +extern int imx9_probe_mu(void *ctx, struct event *event); +void board_init_f(ulong dummy) +{ + int ret; + + /* Clear the BSS. */ + memset(__bss_start, 0, __bss_end - __bss_start); + + timer_init(); + + arch_cpu_init(); + + spl_early_init(); + + preloader_console_init(); + + ret = imx9_probe_mu(NULL, NULL); + if (ret) { + printf("Fail to init ELE API\n"); + } else { + printf("SOC: 0x%x\n", gd->arch.soc_rev); + printf("LC: 0x%x\n", gd->arch.lifecycle); + } + + clock_init(); + + power_init_board(); + + if (!IS_ENABLED(CONFIG_IMX9_LOW_DRIVE_MODE)) + set_arm_core_max_clk(); + + /* Init power of mix */ + soc_power_init(); + + /* Setup TRDC for DDR access */ + trdc_init(); + + /* DDR initialization */ + spl_dram_init(); + + /* Put M33 into CPUWAIT for following kick */ + ret = m33_prepare(); + if (!ret) + printf("M33 prepare ok\n"); + + board_init_r(NULL, 0); +} diff --git a/configs/imx93-phyboard-segin_defconfig b/configs/imx93-phyboard-segin_defconfig new file mode 100644 index 00000000000..91a24c3456d --- /dev/null +++ b/configs/imx93-phyboard-segin_defconfig @@ -0,0 +1,138 @@ +CONFIG_ARM=y +CONFIG_ARCH_IMX9=y +CONFIG_TEXT_BASE=0x80200000 +CONFIG_SYS_MALLOC_LEN=0x2000000 +CONFIG_SYS_MALLOC_F_LEN=0x20000 +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=2 +CONFIG_ENV_SOURCE_FILE="phycore_imx93" +CONFIG_ENV_SIZE=0x10000 +CONFIG_ENV_OFFSET=0x700000 +CONFIG_IMX_CONFIG="arch/arm/mach-imx/imx9/imximage.cfg" +CONFIG_DM_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="imx93-phyboard-segin" +CONFIG_SPL_TEXT_BASE=0x2049A000 +CONFIG_AHAB_BOOT=y +CONFIG_TARGET_PHYCORE_IMX93=y +CONFIG_OF_LIBFDT_OVERLAY=y +CONFIG_SYS_MONITOR_LEN=524288 +CONFIG_SPL_SERIAL=y +CONFIG_SPL_DRIVERS_MISC=y +CONFIG_SPL_STACK=0x20519dd0 +CONFIG_SPL=y +CONFIG_ENV_OFFSET_REDUND=0x720000 +CONFIG_CMD_DEKBLOB=y +CONFIG_SPL_IMX_ROMAPI_LOADADDR=0x88000000 +CONFIG_SYS_LOAD_ADDR=0x80400000 +CONFIG_SYS_MEMTEST_START=0x80000000 +CONFIG_SYS_MEMTEST_END=0x90000000 +CONFIG_REMAKE_ELF=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_OF_SYSTEM_SETUP=y +CONFIG_BOOTCOMMAND="mmc dev ${mmcdev}; if mmc rescan; then if run loadimage; then run mmcboot; else run netboot; fi; fi;" +CONFIG_DEFAULT_FDT_FILE="oftree" +CONFIG_SYS_CBSIZE=2048 +CONFIG_SYS_PBSIZE=2074 +CONFIG_BOARD_LATE_INIT=y +CONFIG_SPL_MAX_SIZE=0x26000 +CONFIG_SPL_HAS_BSS_LINKER_SECTION=y +CONFIG_SPL_BSS_START_ADDR=0x2051a000 +CONFIG_SPL_BSS_MAX_SIZE=0x2000 +CONFIG_SPL_BOARD_INIT=y +CONFIG_SPL_BOOTROM_SUPPORT=y +CONFIG_SPL_LOAD_IMX_CONTAINER=y +CONFIG_IMX_CONTAINER_CFG="arch/arm/mach-imx/imx9/container.cfg" +# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y +CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x1040 +CONFIG_SPL_I2C=y +CONFIG_SPL_POWER=y +CONFIG_SPL_WATCHDOG=y +CONFIG_SYS_PROMPT="u-boot=> " +CONFIG_SYS_MAXARGS=64 +CONFIG_CMD_ERASEENV=y +CONFIG_CMD_NVEDIT_EFI=y +CONFIG_CRC32_VERIFY=y +CONFIG_CMD_EEPROM=y +CONFIG_SYS_I2C_EEPROM_BUS=2 +CONFIG_SYS_I2C_EEPROM_ADDR_LEN=2 +CONFIG_SYS_EEPROM_SIZE=4096 +CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=5 +CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=5 +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_CLK=y +CONFIG_CMD_DFU=y +CONFIG_CMD_FUSE=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_POWEROFF=y +CONFIG_CMD_SNTP=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_EFIDEBUG=y +CONFIG_CMD_RTC=y +CONFIG_CMD_TIME=y +CONFIG_CMD_GETTIME=y +CONFIG_CMD_TIMER=y +CONFIG_CMD_REGULATOR=y +CONFIG_CMD_HASH=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_OF_CONTROL=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_ENV_OVERWRITE=y +CONFIG_ENV_IS_NOWHERE=y +CONFIG_ENV_IS_IN_MMC=y +CONFIG_SYS_REDUNDAND_ENVIRONMENT=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_SYS_MMC_ENV_DEV=1 +CONFIG_USE_ETHPRIME=y +CONFIG_ETHPRIME="eth1" +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_SPL_DM=y +CONFIG_SPL_CLK_IMX93=y +CONFIG_CLK_IMX93=y +CONFIG_DFU_MMC=y +CONFIG_DFU_RAM=y +CONFIG_GPIO_HOG=y +CONFIG_IMX_RGPIO2P=y +CONFIG_DM_I2C=y +CONFIG_SYS_I2C_IMX_LPI2C=y +CONFIG_I2C_EEPROM=y +CONFIG_SYS_I2C_EEPROM_ADDR=0x50 +CONFIG_SUPPORT_EMMC_BOOT=y +CONFIG_MMC_IO_VOLTAGE=y +CONFIG_MMC_UHS_SUPPORT=y +CONFIG_MMC_HS400_ES_SUPPORT=y +CONFIG_MMC_HS400_SUPPORT=y +CONFIG_FSL_USDHC=y +CONFIG_PHY_TI_GENERIC=y +CONFIG_DM_ETH_PHY=y +CONFIG_DWC_ETH_QOS=y +CONFIG_DWC_ETH_QOS_IMX=y +CONFIG_FEC_MXC=y +CONFIG_MII=y +CONFIG_PINCTRL=y +CONFIG_SPL_PINCTRL=y +CONFIG_PINCTRL_IMX93=y +CONFIG_POWER_DOMAIN=y +CONFIG_DM_PMIC=y +CONFIG_DM_PMIC_PCA9450=y +CONFIG_SPL_DM_PMIC_PCA9450=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_PCA9450=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_DM_RTC=y +CONFIG_DM_SERIAL=y +CONFIG_FSL_LPUART=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_SYSRESET=y +CONFIG_SPL_SYSRESET=y +CONFIG_SYSRESET_WATCHDOG=y +CONFIG_DM_THERMAL=y +CONFIG_IMX_TMU=y +CONFIG_ULP_WATCHDOG=y +CONFIG_LZO=y +CONFIG_BZIP2=y diff --git a/doc/board/phytec/imx93-phyboard-segin.rst b/doc/board/phytec/imx93-phyboard-segin.rst new file mode 100644 index 00000000000..da8772ecd5c --- /dev/null +++ b/doc/board/phytec/imx93-phyboard-segin.rst @@ -0,0 +1,61 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +phyBOARD-Segin-i.MX93 +===================== + +U-Boot for the phyBOARD-Segin-i.MX93. + +Quick Start +----------- + +- Get and Build the ARM Trusted firmware +- Get the DDR firmware +- Get ahab-container.img +- Build U-Boot + +Get and Build the ARM Trusted firmware +-------------------------------------- + +Note: srctree is U-Boot source directory +Get ATF from: https://github.com/nxp-imx/imx-atf/ +branch: lf_v2.8 + +.. code-block:: bash + + $ unset LDFLAGS + $ make PLAT=imx93 bl31 + $ cp build/imx93/release/bl31.bin $(srctree) + +Get the DDR firmware +-------------------- + +.. code-block:: bash + + $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.21.bin + $ chmod +x firmware-imx-8.21.bin + $ ./firmware-imx-8.21.bin + $ cp firmware-imx-8.21/firmware/ddr/synopsys/lpddr4*.bin $(srctree) + +Get ahab-container.img +--------------------------------------- + +.. code-block:: bash + + $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-sentinel-0.10.bin + $ chmod +x firmware-sentinel-0.10.bin + $ ./firmware-sentinel-0.10.bin + $ cp firmware-sentinel-0.10/mx93a0-ahab-container.img $(srctree) + +Build U-Boot +------------ + +.. code-block:: bash + + $ make imx93-phyboard-segin_defconfig + $ make + +Burn the flash.bin to MicroSD card offset 32KB: + +.. code-block:: bash + + $ dd if=flash.bin of=/dev/sd[x] bs=1024 seek=32 conv=notrunc diff --git a/doc/board/phytec/index.rst b/doc/board/phytec/index.rst index 965d40de4d4..fea0b076202 100644 --- a/doc/board/phytec/index.rst +++ b/doc/board/phytec/index.rst @@ -7,6 +7,7 @@ PHYTEC :maxdepth: 2 imx8mm-phygate-tauri-l + imx93-phyboard-segin phycore-am62x phycore-imx8mm phycore-imx8mp diff --git a/include/configs/phycore_imx93.h b/include/configs/phycore_imx93.h new file mode 100644 index 00000000000..07364dff403 --- /dev/null +++ b/include/configs/phycore_imx93.h @@ -0,0 +1,28 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Copyright 2022 NXP + * Copyright (C) 2023 PHYTEC Messtechnik GmbH + * Christoph Stoidner <c.stoidner@phytec.de> + * Copyright (C) 2024 Mathieu Othacehe <m.othacehe@gmail.com> + */ + +#ifndef __PHYCORE_IMX93_H +#define __PHYCORE_IMX93_H + +#include <linux/sizes.h> +#include <asm/arch/imx-regs.h> + +#define CFG_SYS_UBOOT_BASE \ + (QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512) + +#define CFG_SYS_INIT_RAM_ADDR 0x80000000 +#define CFG_SYS_INIT_RAM_SIZE 0x200000 + +#define CFG_SYS_SDRAM_BASE 0x80000000 +#define PHYS_SDRAM 0x80000000 +#define PHYS_SDRAM_SIZE 0x80000000 + +/* Using ULP WDOG for reset */ +#define WDOG_BASE_ADDR WDG3_BASE_ADDR + +#endif /* __PHYCORE_IMX93_H */
Add initial support for the PHYTEC phyBOARD-Segin-i.MX93 board based on the PHYTEC phyCORE-i.MX93 SoM. Supported features: - 1GB LPDDR4 RAM - eMMC - external SD - FEC Ethernet - debug UART - watchdog Signed-off-by: Mathieu Othacehe <othacehe@gnu.org> --- Hello, This new revision fixes the remarks of Primoz. The configuration is now aligned on the savedefconfig output. The FEC Ethernet is also tested to be working if this patch is in: https://patchwork.ozlabs.org/project/uboot/patch/20240130124337.497748-1-primoz.fiser@norik.com/ The proposed patch has been rebased on top of 6faba41. Thanks, Mathieu v3: https://lists.denx.de/pipermail/u-boot/2024-January/544493.html arch/arm/dts/Makefile | 3 +- arch/arm/dts/imx93-phyboard-segin-u-boot.dtsi | 293 ++++ arch/arm/dts/imx93-phyboard-segin.dts | 117 ++ arch/arm/dts/imx93-phycore-som.dtsi | 126 ++ arch/arm/mach-imx/imx9/Kconfig | 6 + board/phytec/phycore_imx93/Kconfig | 13 + board/phytec/phycore_imx93/MAINTAINERS | 10 + board/phytec/phycore_imx93/Makefile | 14 + board/phytec/phycore_imx93/lpddr4_timing.c | 1546 +++++++++++++++++ board/phytec/phycore_imx93/phycore-imx93.c | 42 + board/phytec/phycore_imx93/phycore_imx93.env | 73 + board/phytec/phycore_imx93/spl.c | 148 ++ configs/imx93-phyboard-segin_defconfig | 138 ++ doc/board/phytec/imx93-phyboard-segin.rst | 61 + doc/board/phytec/index.rst | 1 + include/configs/phycore_imx93.h | 28 + 16 files changed, 2618 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/imx93-phyboard-segin-u-boot.dtsi create mode 100644 arch/arm/dts/imx93-phyboard-segin.dts create mode 100644 arch/arm/dts/imx93-phycore-som.dtsi create mode 100644 board/phytec/phycore_imx93/Kconfig create mode 100644 board/phytec/phycore_imx93/MAINTAINERS create mode 100644 board/phytec/phycore_imx93/Makefile create mode 100644 board/phytec/phycore_imx93/lpddr4_timing.c create mode 100644 board/phytec/phycore_imx93/phycore-imx93.c create mode 100644 board/phytec/phycore_imx93/phycore_imx93.env create mode 100644 board/phytec/phycore_imx93/spl.c create mode 100644 configs/imx93-phyboard-segin_defconfig create mode 100644 doc/board/phytec/imx93-phyboard-segin.rst create mode 100644 include/configs/phycore_imx93.h