Message ID | 20231026-ina237-v2-0-dec44811a3c9@linux.dev |
---|---|
Headers | show |
Series | hwmon: add ti,ina237 support to ina238 driver | expand |
On Thu, Oct 26, 2023 at 09:08:49AM +0200, Richard Leitner wrote: > The INA237 "85-V, 16-Bit, Precision Power Monitor With I2C Interface" is > basically the same as INA328. Therefore add a corresponding compatible > to the driver. > > According to the datasheet the main difference is the current and power > monitoring accuracy: > > +------------------------+---------------+---------------+ > | | INA238 | INA237 | > +------------------------+---------------+---------------+ > | Offset voltage | +/- 5µV | +/- 50µV | > | Offset drift | +/- 0.02µV/°C | +/- 0.02µV/°C | > | Gain error | +/- 0.1% | +/- 0.3% | > | Gain error drift | +/- 25ppm/°C | +/- 50ppm/°C | > | Common mode rejection | 140dB | 120dB | > | Power accuracy | 0.7% | 1.6% | > +------------------------+---------------+---------------+ > > As well as the missing DEVICE_ID register at 0x3F, which is currently > not in use by the driver. > > Signed-off-by: Richard Leitner <richard.leitner@linux.dev> Applied. Thanks, Guenter > --- > drivers/hwmon/ina238.c | 3 ++- > 1 file changed, 2 insertions(+), 1 deletion(-) > > diff --git a/drivers/hwmon/ina238.c b/drivers/hwmon/ina238.c > index f519c22d3907..ca9f5d2c811b 100644 > --- a/drivers/hwmon/ina238.c > +++ b/drivers/hwmon/ina238.c > @@ -33,7 +33,7 @@ > #define INA238_BUS_UNDER_VOLTAGE 0xf > #define INA238_TEMP_LIMIT 0x10 > #define INA238_POWER_LIMIT 0x11 > -#define INA238_DEVICE_ID 0x3f > +#define INA238_DEVICE_ID 0x3f /* not available on INA237 */ > > #define INA238_CONFIG_ADCRANGE BIT(4) > > @@ -622,6 +622,7 @@ static const struct i2c_device_id ina238_id[] = { > MODULE_DEVICE_TABLE(i2c, ina238_id); > > static const struct of_device_id __maybe_unused ina238_of_match[] = { > + { .compatible = "ti,ina237" }, > { .compatible = "ti,ina238" }, > { }, > };
This series adds support for the ina237 power monitor to the ina238 driver as those two are very similar. Signed-off-by: Richard Leitner <richard.leitner@linux.dev> --- Changes in v2: - Drop separate MAINTAINERS entry as it's covered by hwmon - Drop separate dt-bindings for ina23{7,8} as discussed with Krzysztof - Link to v1: https://lore.kernel.org/r/20231025-ina237-v1-0-a0196119720c@linux.dev --- Richard Leitner (2): hwmon: ina238: add ina237 support dt-bindings: hwmon: ti,ina2xx: add ti,ina237 Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml | 1 + drivers/hwmon/ina238.c | 3 ++- 2 files changed, 3 insertions(+), 1 deletion(-) --- base-commit: 4f82870119a46b0d04d91ef4697ac4977a255a9d change-id: 20231025-ina237-0f1a9c14fd5d Best regards,