Message ID | 20230509132948.17808-1-zajec5@gmail.com |
---|---|
State | Accepted |
Delegated to: | Rafał Miłecki |
Headers | show |
Series | ramips: set Netgear R6220 MAC NVMEM cell directly in the part node | expand |
Am 9. Mai 2023 15:29:48 MESZ schrieb "Rafał Miłecki" <zajec5@gmail.com>: >From: Rafał Miłecki <rafal@milecki.pl> > >There is no need to use reference if original node it specified in >exactly the same file. This is a minor cleanup simplifying DTS code. > >Signed-off-by: Rafał Miłecki <rafal@milecki.pl> >--- > .../linux/ramips/dts/mt7621_netgear_r6220.dts | 18 ++++++++---------- > 1 file changed, 8 insertions(+), 10 deletions(-) > >diff --git a/target/linux/ramips/dts/mt7621_netgear_r6220.dts b/target/linux/ramips/dts/mt7621_netgear_r6220.dts >index 0f476ef060..7bb49c15b4 100644 >--- a/target/linux/ramips/dts/mt7621_netgear_r6220.dts >+++ b/target/linux/ramips/dts/mt7621_netgear_r6220.dts >@@ -42,9 +42,17 @@ > }; > > factory: partition@2e00000 { The "factory" reference could be probably be dropped as well. Proposed changes look good to me. >+ compatible = "nvmem-cells"; > label = "factory"; > reg = <0x2e00000 0x100000>; > read-only; >+ >+ #address-cells = <1>; >+ #size-cells = <1>; >+ >+ macaddr_factory_4: macaddr@4 { >+ reg = <0x4 0x6>; >+ }; > }; > > partition@4200000 { >@@ -65,13 +73,3 @@ > nvmem-cell-names = "mac-address"; > mac-address-increment = <1>; > }; >- >-&factory { >- compatible = "nvmem-cells"; >- #address-cells = <1>; >- #size-cells = <1>; >- >- macaddr_factory_4: macaddr@4 { >- reg = <0x4 0x6>; >- }; >-}; >-- >2.35.3 > > >_______________________________________________ >openwrt-devel mailing list >openwrt-devel@lists.openwrt.org >https://lists.openwrt.org/mailman/listinfo/openwrt-devel Viele Grüße Felix von Freifunk
On 9.05.2023 18:21, Felix Baumann wrote: > Am 9. Mai 2023 15:29:48 MESZ schrieb "Rafał Miłecki" <zajec5@gmail.com>: >> From: Rafał Miłecki <rafal@milecki.pl> >> >> There is no need to use reference if original node it specified in >> exactly the same file. This is a minor cleanup simplifying DTS code. >> >> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> >> --- >> .../linux/ramips/dts/mt7621_netgear_r6220.dts | 18 ++++++++---------- >> 1 file changed, 8 insertions(+), 10 deletions(-) >> >> diff --git a/target/linux/ramips/dts/mt7621_netgear_r6220.dts b/target/linux/ramips/dts/mt7621_netgear_r6220.dts >> index 0f476ef060..7bb49c15b4 100644 >> --- a/target/linux/ramips/dts/mt7621_netgear_r6220.dts >> +++ b/target/linux/ramips/dts/mt7621_netgear_r6220.dts >> @@ -42,9 +42,17 @@ >> }; >> >> factory: partition@2e00000 { > > The "factory" reference could be probably be dropped as well. Proposed changes look good to me. Actually it can't be dropped. While it's a bit counter-intuitive, that label is used in a *parent* DTS file mt7621_netgear_sercomm_ayx.dtsi . >> + compatible = "nvmem-cells"; >> label = "factory"; >> reg = <0x2e00000 0x100000>; >> read-only; >> + >> + #address-cells = <1>; >> + #size-cells = <1>; >> + >> + macaddr_factory_4: macaddr@4 { >> + reg = <0x4 0x6>; >> + }; >> }; >> >> partition@4200000 { >> @@ -65,13 +73,3 @@ >> nvmem-cell-names = "mac-address"; >> mac-address-increment = <1>; >> }; >> - >> -&factory { >> - compatible = "nvmem-cells"; >> - #address-cells = <1>; >> - #size-cells = <1>; >> - >> - macaddr_factory_4: macaddr@4 { >> - reg = <0x4 0x6>; >> - }; >> -}; >> -- >> 2.35.3
Am 14. Juli 2023 10:26:33 MESZ schrieb "Rafał Miłecki" <zajec5@gmail.com>: >On 9.05.2023 18:21, Felix Baumann wrote: >> Am 9. Mai 2023 15:29:48 MESZ schrieb "Rafał Miłecki" <zajec5@gmail.com>: >>> From: Rafał Miłecki <rafal@milecki.pl> >>> >>> There is no need to use reference if original node it specified in >>> exactly the same file. This is a minor cleanup simplifying DTS code. >>> >>> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> >>> --- >>> .../linux/ramips/dts/mt7621_netgear_r6220.dts | 18 ++++++++---------- >>> 1 file changed, 8 insertions(+), 10 deletions(-) >>> >>> diff --git a/target/linux/ramips/dts/mt7621_netgear_r6220.dts b/target/linux/ramips/dts/mt7621_netgear_r6220.dts >>> index 0f476ef060..7bb49c15b4 100644 >>> --- a/target/linux/ramips/dts/mt7621_netgear_r6220.dts >>> +++ b/target/linux/ramips/dts/mt7621_netgear_r6220.dts >>> @@ -42,9 +42,17 @@ >>> }; >>> >>> factory: partition@2e00000 { >> >> The "factory" reference could be probably be dropped as well. Proposed changes look good to me. > >Actually it can't be dropped. While it's a bit counter-intuitive, that >label is used in a *parent* DTS file mt7621_netgear_sercomm_ayx.dtsi . Hello Rafał, I was under the strong impression that dts(i) files could only get reference from the same file or parents but not childs. I remember reading a few exchanges by Ansuel, I think, that mentioned this. I might be mixing two topics here, but was this (intended to be) fixed by dynamic partitions or something like that? Are you certain the eeprom is loaded successfully? Aren't dts(i) files read from top to bottom? Regards Felix Baumann
On 2023-07-14 11:57, Felix Baumann wrote: > Am 14. Juli 2023 10:26:33 MESZ schrieb "Rafał Miłecki" > <zajec5@gmail.com>: >> On 9.05.2023 18:21, Felix Baumann wrote: >>> Am 9. Mai 2023 15:29:48 MESZ schrieb "Rafał Miłecki" >>> <zajec5@gmail.com>: >>>> From: Rafał Miłecki <rafal@milecki.pl> >>>> >>>> There is no need to use reference if original node it specified in >>>> exactly the same file. This is a minor cleanup simplifying DTS code. >>>> >>>> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> >>>> --- >>>> .../linux/ramips/dts/mt7621_netgear_r6220.dts | 18 >>>> ++++++++---------- >>>> 1 file changed, 8 insertions(+), 10 deletions(-) >>>> >>>> diff --git a/target/linux/ramips/dts/mt7621_netgear_r6220.dts >>>> b/target/linux/ramips/dts/mt7621_netgear_r6220.dts >>>> index 0f476ef060..7bb49c15b4 100644 >>>> --- a/target/linux/ramips/dts/mt7621_netgear_r6220.dts >>>> +++ b/target/linux/ramips/dts/mt7621_netgear_r6220.dts >>>> @@ -42,9 +42,17 @@ >>>> }; >>>> >>>> factory: partition@2e00000 { >>> >>> The "factory" reference could be probably be dropped as well. >>> Proposed changes look good to me. >> >> Actually it can't be dropped. While it's a bit counter-intuitive, that >> label is used in a *parent* DTS file mt7621_netgear_sercomm_ayx.dtsi . > > Hello Rafał, > > I was under the strong impression that dts(i) files could only get > reference from the same file or parents but not childs. I remember > reading a few exchanges by Ansuel, I think, that mentioned this. > I might be mixing two topics here, but was this (intended to be) fixed > by dynamic partitions or something like that? > > Are you certain the eeprom is loaded successfully? > > Aren't dts(i) files read from top to bottom? I just verified that and it works. First I decompiled .dtb from the latest "master" branch with: dtc -I dtb -O dts -o r6220.dts build_dir/target-mipsel_24kc_musl/linux-ramips_mt7621/image-mt7621_netgear_r6220.dtb Then I opened r6220.dts and analyzed it. My MAC cell looks like this: macaddr@4 { compatible = "mac-base"; reg = <0x04 0x06>; #nvmem-cell-cells = <0x01>; phandle = <0x13>; }; Then my Ethernet controller nodes look like that: mac@0 { compatible = "mediatek,eth-mac"; reg = <0x00>; nvmem-cells = <0x13 0x00>; nvmem-cell-names = "mac-address"; (...) }; mac@1 { compatible = "mediatek,eth-mac"; reg = <0x01>; status = "okay"; nvmem-cells = <0x13 0x01>; nvmem-cell-names = "mac-address"; (...) }; As you can see both reference phandle 0x13 so that looks all good.
diff --git a/target/linux/ramips/dts/mt7621_netgear_r6220.dts b/target/linux/ramips/dts/mt7621_netgear_r6220.dts index 0f476ef060..7bb49c15b4 100644 --- a/target/linux/ramips/dts/mt7621_netgear_r6220.dts +++ b/target/linux/ramips/dts/mt7621_netgear_r6220.dts @@ -42,9 +42,17 @@ }; factory: partition@2e00000 { + compatible = "nvmem-cells"; label = "factory"; reg = <0x2e00000 0x100000>; read-only; + + #address-cells = <1>; + #size-cells = <1>; + + macaddr_factory_4: macaddr@4 { + reg = <0x4 0x6>; + }; }; partition@4200000 { @@ -65,13 +73,3 @@ nvmem-cell-names = "mac-address"; mac-address-increment = <1>; }; - -&factory { - compatible = "nvmem-cells"; - #address-cells = <1>; - #size-cells = <1>; - - macaddr_factory_4: macaddr@4 { - reg = <0x4 0x6>; - }; -};