diff mbox

[U-Boot,2/3,v2] phylib: wait for TN2020 to achieve SERDES lane alignment at startup

Message ID 1318019722-11095-2-git-send-email-timur@freescale.com
State Accepted
Commit 2339e4972f55c9daa0d0e297ad3378c53e2f6fc3
Delegated to: Kumar Gala
Headers show

Commit Message

Timur Tabi Oct. 7, 2011, 8:35 p.m. UTC 
Before the Teranetics TN2020 PHY can be used, the SERDES lanes need to be
aligned, so wait for lane alignment before completing the startup sequence.

Note that this process can take up to three seconds.

Signed-off-by: Timur Tabi <timur@freescale.com>
---
 drivers/net/phy/teranetics.c |   33 +++++++++++++++++++++++++++++++++
 1 files changed, 33 insertions(+), 0 deletions(-)

Comments

Kumar Gala Oct. 21, 2011, 5:08 a.m. UTC | #1 
On Oct 7, 2011, at 3:35 PM, Timur Tabi wrote:

> Before the Teranetics TN2020 PHY can be used, the SERDES lanes need to be
> aligned, so wait for lane alignment before completing the startup sequence.
> 
> Note that this process can take up to three seconds.
> 
> Signed-off-by: Timur Tabi <timur@freescale.com>
> ---
> drivers/net/phy/teranetics.c |   33 +++++++++++++++++++++++++++++++++
> 1 files changed, 33 insertions(+), 0 deletions(-)

applied to 85xx

- k
diff mbox

Patch

diff --git a/drivers/net/phy/teranetics.c b/drivers/net/phy/teranetics.c
index a13b48c..9d9397a 100644
--- a/drivers/net/phy/teranetics.c
+++ b/drivers/net/phy/teranetics.c
@@ -21,6 +21,7 @@ 
  *
  */
 #include <config.h>
+#include <common.h>
 #include <phy.h>
 
 #ifndef CONFIG_PHYLIB_10G
@@ -43,6 +44,38 @@  int tn2020_config(struct phy_device *phydev)
 
 int tn2020_startup(struct phy_device *phydev)
 {
+	unsigned int timeout = 5 * 1000; /* 5 second timeout */
+
+#define MDIO_PHYXS_LANE_READY (MDIO_PHYXS_LNSTAT_SYNC0 | \
+			       MDIO_PHYXS_LNSTAT_SYNC1 | \
+			       MDIO_PHYXS_LNSTAT_SYNC2 | \
+			       MDIO_PHYXS_LNSTAT_SYNC3 | \
+			       MDIO_PHYXS_LNSTAT_ALIGN)
+
+	/*
+	 * Wait for the XAUI-SERDES lanes to align first.  Under normal
+	 * circumstances, this can take up to three seconds.
+	 */
+	while (--timeout) {
+		int reg = phy_read(phydev, MDIO_MMD_PHYXS, MDIO_PHYXS_LNSTAT);
+		if (reg < 0) {
+			printf("TN2020: Error reading from PHY at "
+			       "address %u\n", phydev->addr);
+			break;
+		}
+		if ((reg & MDIO_PHYXS_LANE_READY) == MDIO_PHYXS_LANE_READY)
+			break;
+		udelay(1000);
+	}
+	if (!timeout) {
+		/*
+		 * A timeout is bad, but it may not be fatal, so don't
+		 * return an error.  Display a warning instead.
+		 */
+		printf("TN2020: Timeout waiting for PHY at address %u to "
+		       "align.\n", phydev->addr);
+	}
+
 	if (phydev->port != PORT_FIBRE)
 		return gen10g_startup(phydev);