Message ID | 20210501201306.4996-1-andrey.zhizhikin@leica-geosystems.com |
---|---|
State | Changes Requested |
Delegated to: | Stefano Babic |
Headers | show |
Series | arm: imx: imx8mm: correct unrecognized fracpll frequency | expand |
On Sat, May 1, 2021 at 5:13 PM Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> wrote: > > Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ() > macro, which expands the value provided to the Hz range without taking into > account the precise Hz setting. This causes the frequency of 266 MHz not ot > be found in the imx8mm_fracpll_tbl, since it is entered there with a > precise Hz value. This in turn causes the boot hang in SPL, as proper DDR > fracpll frequency cannot be determined. > > Correct the value in imx8mm_fracpll_tbl to match the one expanded by > MHZ(266) macro, rounding it down to MHz range only. > > Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> > Cc: Stefano Babic <sbabic@denx.de> > Cc: Fabio Estevam <festevam@gmail.com> > Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com> > Cc: Peng Fan <peng.fan@nxp.com> > Cc: Simon Glass <sjg@chromium.org> > Cc: Ye Li <ye.li@nxp.com> > Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m") Reviewed-by: Fabio Estevam <festevam@gmail.com>
Hi Andrey, After re-reading the patch I have some comments: On Sat, May 1, 2021 at 5:13 PM Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> wrote: > > Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ() > macro, which expands the value provided to the Hz range without taking into > account the precise Hz setting. This causes the frequency of 266 MHz not ot > be found in the imx8mm_fracpll_tbl, since it is entered there with a > precise Hz value. This in turn causes the boot hang in SPL, as proper DDR > fracpll frequency cannot be determined. > > Correct the value in imx8mm_fracpll_tbl to match the one expanded by > MHZ(266) macro, rounding it down to MHz range only. > > Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> > Cc: Stefano Babic <sbabic@denx.de> > Cc: Fabio Estevam <festevam@gmail.com> > Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com> > Cc: Peng Fan <peng.fan@nxp.com> > Cc: Simon Glass <sjg@chromium.org> > Cc: Ye Li <ye.li@nxp.com> > Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m") > --- > arch/arm/mach-imx/imx8m/clock_imx8mm.c | 6 +++--- > 1 file changed, 3 insertions(+), 3 deletions(-) > > diff --git a/arch/arm/mach-imx/imx8m/clock_imx8mm.c b/arch/arm/mach-imx/imx8m/clock_imx8mm.c > index 029d06f27f..86ff2b9cc9 100644 > --- a/arch/arm/mach-imx/imx8m/clock_imx8mm.c > +++ b/arch/arm/mach-imx/imx8m/clock_imx8mm.c > @@ -54,7 +54,7 @@ static struct imx_int_pll_rate_table imx8mm_fracpll_tbl[] = { > PLL_1443X_RATE(600000000U, 300, 3, 2, 0), > PLL_1443X_RATE(594000000U, 99, 1, 2, 0), > PLL_1443X_RATE(400000000U, 300, 9, 1, 0), > - PLL_1443X_RATE(266666667U, 400, 9, 2, 0), > + PLL_1443X_RATE(266000000U, 400, 9, 2, 0), This change looks good. > PLL_1443X_RATE(167000000U, 334, 3, 4, 0), > PLL_1443X_RATE(100000000U, 300, 9, 3, 0), > }; > @@ -72,7 +72,7 @@ static int fracpll_configure(enum pll_clocks pll, u32 freq) > } > > if (i == ARRAY_SIZE(imx8mm_fracpll_tbl)) { > - printf("No matched freq table %u\n", freq); > + printf("%s: No matched freq table %u\n", __func__, freq); > return -EINVAL; > } > > @@ -148,7 +148,7 @@ void dram_enable_bypass(ulong clk_val) > } > > if (i == ARRAY_SIZE(imx8mm_dram_bypass_tbl)) { > - printf("No matched freq table %lu\n", clk_val); > + printf("%s: No matched freq table %lu\n", __func__, clk_val); , but these two I would put them on a separate patch. Thanks
Hello Fabio, > -----Original Message----- > From: Fabio Estevam <festevam@gmail.com> > Sent: Sunday, May 2, 2021 11:45 PM > To: ZHIZHIKIN Andrey <andrey.zhizhikin@leica-geosystems.com> > Cc: U-Boot-Denx <u-boot@lists.denx.de>; Stefano Babic <sbabic@denx.de>; > NXP i.MX U-Boot Team <uboot-imx@nxp.com>; Peng Fan > <peng.fan@nxp.com>; Simon Glass <sjg@chromium.org>; Ye Li <ye.li@nxp.com> > Subject: Re: [PATCH] arm: imx: imx8mm: correct unrecognized fracpll frequency > > > Hi Andrey, > > After re-reading the patch I have some comments: > > On Sat, May 1, 2021 at 5:13 PM Andrey Zhizhikin <andrey.zhizhikin@leica- > geosystems.com> wrote: > > > > Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ() > > macro, which expands the value provided to the Hz range without taking > > into account the precise Hz setting. This causes the frequency of 266 > > MHz not ot be found in the imx8mm_fracpll_tbl, since it is entered > > there with a precise Hz value. This in turn causes the boot hang in > > SPL, as proper DDR fracpll frequency cannot be determined. > > > > Correct the value in imx8mm_fracpll_tbl to match the one expanded by > > MHZ(266) macro, rounding it down to MHz range only. > > > > Signed-off-by: Andrey Zhizhikin > > <andrey.zhizhikin@leica-geosystems.com> > > Cc: Stefano Babic <sbabic@denx.de> > > Cc: Fabio Estevam <festevam@gmail.com> > > Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com> > > Cc: Peng Fan <peng.fan@nxp.com> > > Cc: Simon Glass <sjg@chromium.org> > > Cc: Ye Li <ye.li@nxp.com> > > Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m") > > --- > > arch/arm/mach-imx/imx8m/clock_imx8mm.c | 6 +++--- > > 1 file changed, 3 insertions(+), 3 deletions(-) > > > > diff --git a/arch/arm/mach-imx/imx8m/clock_imx8mm.c > > b/arch/arm/mach-imx/imx8m/clock_imx8mm.c > > index 029d06f27f..86ff2b9cc9 100644 > > --- a/arch/arm/mach-imx/imx8m/clock_imx8mm.c > > +++ b/arch/arm/mach-imx/imx8m/clock_imx8mm.c > > @@ -54,7 +54,7 @@ static struct imx_int_pll_rate_table imx8mm_fracpll_tbl[] > = { > > PLL_1443X_RATE(600000000U, 300, 3, 2, 0), > > PLL_1443X_RATE(594000000U, 99, 1, 2, 0), > > PLL_1443X_RATE(400000000U, 300, 9, 1, 0), > > - PLL_1443X_RATE(266666667U, 400, 9, 2, 0), > > + PLL_1443X_RATE(266000000U, 400, 9, 2, 0), > > This change looks good. > > > PLL_1443X_RATE(167000000U, 334, 3, 4, 0), > > PLL_1443X_RATE(100000000U, 300, 9, 3, 0), }; @@ -72,7 +72,7 > > @@ static int fracpll_configure(enum pll_clocks pll, u32 freq) > > } > > > > if (i == ARRAY_SIZE(imx8mm_fracpll_tbl)) { > > - printf("No matched freq table %u\n", freq); > > + printf("%s: No matched freq table %u\n", __func__, > > + freq); > > return -EINVAL; > > } > > > > @@ -148,7 +148,7 @@ void dram_enable_bypass(ulong clk_val) > > } > > > > if (i == ARRAY_SIZE(imx8mm_dram_bypass_tbl)) { > > - printf("No matched freq table %lu\n", clk_val); > > + printf("%s: No matched freq table %lu\n", __func__, > > + clk_val); > > , but these two I would put them on a separate patch. Fair enough, thanks for pointing this out! Even though this helped me originally to pinpoint the issue, looking at this change now I see it does indeed belong to the separate patch as it does not relate to the PLL fix per se. I would split this into a separate patch, send it separate, and send a V2 for the PLL fix. > > Thanks Cheers, Andrey
diff --git a/arch/arm/mach-imx/imx8m/clock_imx8mm.c b/arch/arm/mach-imx/imx8m/clock_imx8mm.c index 029d06f27f..86ff2b9cc9 100644 --- a/arch/arm/mach-imx/imx8m/clock_imx8mm.c +++ b/arch/arm/mach-imx/imx8m/clock_imx8mm.c @@ -54,7 +54,7 @@ static struct imx_int_pll_rate_table imx8mm_fracpll_tbl[] = { PLL_1443X_RATE(600000000U, 300, 3, 2, 0), PLL_1443X_RATE(594000000U, 99, 1, 2, 0), PLL_1443X_RATE(400000000U, 300, 9, 1, 0), - PLL_1443X_RATE(266666667U, 400, 9, 2, 0), + PLL_1443X_RATE(266000000U, 400, 9, 2, 0), PLL_1443X_RATE(167000000U, 334, 3, 4, 0), PLL_1443X_RATE(100000000U, 300, 9, 3, 0), }; @@ -72,7 +72,7 @@ static int fracpll_configure(enum pll_clocks pll, u32 freq) } if (i == ARRAY_SIZE(imx8mm_fracpll_tbl)) { - printf("No matched freq table %u\n", freq); + printf("%s: No matched freq table %u\n", __func__, freq); return -EINVAL; } @@ -148,7 +148,7 @@ void dram_enable_bypass(ulong clk_val) } if (i == ARRAY_SIZE(imx8mm_dram_bypass_tbl)) { - printf("No matched freq table %lu\n", clk_val); + printf("%s: No matched freq table %lu\n", __func__, clk_val); return; }
Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ() macro, which expands the value provided to the Hz range without taking into account the precise Hz setting. This causes the frequency of 266 MHz not ot be found in the imx8mm_fracpll_tbl, since it is entered there with a precise Hz value. This in turn causes the boot hang in SPL, as proper DDR fracpll frequency cannot be determined. Correct the value in imx8mm_fracpll_tbl to match the one expanded by MHZ(266) macro, rounding it down to MHz range only. Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Simon Glass <sjg@chromium.org> Cc: Ye Li <ye.li@nxp.com> Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m") --- arch/arm/mach-imx/imx8m/clock_imx8mm.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)