| Message ID | 20210113070850.1184506-2-troy_lee@aspeedtech.com |
|---|---|
| State | New |
| Headers | show |
| Series | hwmon: aspeed2600-pwm-tacho: Add driver support | expand |
On Wed, 13 Jan 2021 07:08:45 +0000, Troy Lee wrote: > We add binding for supporting a new AST2600 PWM/Fan hwmon driver. > > Changes since v1: > - dt binding with DT schema format > > Signed-off-by: Troy Lee <troy_lee@aspeedtech.com> > --- > .../hwmon/aspeed,ast2600-pwm-tachometer.yaml | 137 ++++++++++++++++++ > 1 file changed, 137 insertions(+) > create mode 100644 Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml > My bot found errors running 'make dt_binding_check' on your patch: yamllint warnings/errors: ./Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml:108:2: [warning] wrong indentation: expected 2 but found 1 (indentation) dtschema/dtc warnings/errors: See https://patchwork.ozlabs.org/patch/1425628 This check can fail if there are any dependencies. The base for a patch series is generally the most recent rc1. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit.
Hi Rob, The 01/13/2021 23:45, Rob Herring wrote: > On Wed, 13 Jan 2021 07:08:45 +0000, Troy Lee wrote: > > We add binding for supporting a new AST2600 PWM/Fan hwmon driver. > > > > Changes since v1: > > - dt binding with DT schema format > > > > Signed-off-by: Troy Lee <troy_lee@aspeedtech.com> > > --- > > .../hwmon/aspeed,ast2600-pwm-tachometer.yaml | 137 ++++++++++++++++++ > > 1 file changed, 137 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml > > > > My bot found errors running 'make dt_binding_check' on your patch: > > yamllint warnings/errors: > ./Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml:108:2: [warning] wrong indentation: expected 2 but found 1 (indentation) > > dtschema/dtc warnings/errors: > > See https://patchwork.ozlabs.org/patch/1425628 > > This check can fail if there are any dependencies. The base for a patch > series is generally the most recent rc1. > > If you already ran 'make dt_binding_check' and didn't see the above > error(s), then make sure 'yamllint' is installed and dt-schema is up to > date: > > pip3 install dtschema --upgrade > > Please check and re-submit. > After install yamllint and ran 'make dt_binding_check' again, I can see the same issue. I'll fix it in v3 patch set. Thanks, Troy Lee
On Wed, Jan 13, 2021 at 07:08:45AM +0000, Troy Lee wrote: > We add binding for supporting a new AST2600 PWM/Fan hwmon driver. > > Changes since v1: > - dt binding with DT schema format > > Signed-off-by: Troy Lee <troy_lee@aspeedtech.com> > --- > .../hwmon/aspeed,ast2600-pwm-tachometer.yaml | 137 ++++++++++++++++++ > 1 file changed, 137 insertions(+) > create mode 100644 Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml > > diff --git a/Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml b/Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml > new file mode 100644 > index 000000000000..b84076a4a338 > --- /dev/null > +++ b/Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml > @@ -0,0 +1,137 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > + > +$id: http://devicetree.org/schemas/hwmon/aspeed,ast2600-pwm-tachometer.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: ASPEED AST2600 PWM and Fan Tacho controller device driver > + > +maintainers: > + - Ryan Chen <ryan_chen@aspeedtech.com> > + > +description: | > + The ASPEED PWM controller can support upto 16 PWM outputs. The ASPEED Fan Tacho > + controller can support upto 16 Fan tachometer inputs. > + There can be upto 16 fans supported. Each fan can have one PWM output and > + one Fan tach inputs. > + > +properties: > + compatible: > + const: aspeed,ast2600-pwm-tachometer > + > + "#address-cells": > + const: 1 > + > + "#size-cells": > + const: 0 > + > + "#cooling-cells": > + const: 2 > + > + reg: > + description: > + Address and length of the register set for the device. No need for generic descriptions. That's every 'reg'. What you need is how many entries and what each one is if more than 1. If only 1, then just 'maxItems: 1' > + > + clocks: > + description: > + phandle to clock provider with the clock number in the second cell Same here. > + > + resets: > + description: > + phandle to reset controller with the reset number in the second cell And here. > + > +patternProperties: > + "@[0-9]+$": If every node is a fan and there are up to 16: ^fan@[0-9a-f]$ > + type: object > + description: > + Under fan subnode there can upto 16 child nodes, with each child node > + representing a fan. There are 16 fans each fan can have one PWM port and one > + Fan tach inputs. > + For PWM port can be configured cooling-levels to create cooling device. > + Cooling device could be bound to a thermal zone for the thermal control. > + > + properties: > + reg: > + minimum: 0 > + maximum: 15 > + description: > + This property identify the PWM control channel of this fan. > + > + fan-tach-ch: > + $ref: /schemas/types.yaml#/definitions/uint8 > + minimum: 0 > + maximum: 15 > + description: > + This property identify the fan tach input channel. > + > + pulses-per-revolution: > + $ref: /schemas/types.yaml#/definitions/uint32 > + default: 2 > + minimum: 1 > + description: > + Specify tacho pulse per revolution of the fan. > + > + cooling-levels: > + description: > + PWM duty cycle values in a range from 0 to 255 > + which correspond to thermal cooling states. > + > + aspeed,pwm-freq: > + $ref: /schemas/types.yaml#/definitions/uint32 > + default: 25000 > + minimum: 24 > + maximum: 780000 > + description: > + Specify the frequency of PWM. Units? Use a unit suffix and then drop the $ref. > + > + aspeed,inverse-pin: > + type: boolean > + description: > + Inverse PWM output signal. > + > + aspeed,falling-point: > + $ref: /schemas/types.yaml#/definitions/uint8 > + default: 10 > + minimum: 0 > + maximum: 255 0-255 is already the range of uint8, so drop. > + description: > + Initialize the pulse width. > + > + required: > + - fan-tach-ch > + - reg > + > + additionalProperties: true > + > +required: > + - compatible > + - reg > + > +additionalProperties: false > + > +examples: > + - | > + pwm_tacho: pwm-tacho-controller@1e610000 { > + compatible = "aspeed,ast2600-pwm-tachometer"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0x1e610000 0x100>; > + > + fan@1 { > + reg = <0x00>; > + aspeed,pwm-freq = <25000>; > + cooling-levels = /bits/ 8 <125 151 177 203 229 255>; > + fan-tach-ch = /bits/ 8 <0x00>; > + pulses-per-revolution = <2>; > + }; > + > + fan@2 { > + reg = <0x01>; > + aspeed,pwm-freq = <25000>; > + cooling-levels = /bits/ 8 <125 151 177 203 229 255>; > + fan-tach-ch = /bits/ 8 <0x01>; > + pulses-per-revolution = <2>; > + }; > + }; > +... > -- > 2.25.1 >
Hi Rob, Thanks for reviewing. The 01/14/2021 22:13, Rob Herring wrote: > On Wed, Jan 13, 2021 at 07:08:45AM +0000, Troy Lee wrote: > > We add binding for supporting a new AST2600 PWM/Fan hwmon driver. > > > > Changes since v1: > > - dt binding with DT schema format > > > > Signed-off-by: Troy Lee <troy_lee@aspeedtech.com> > > --- > > .../hwmon/aspeed,ast2600-pwm-tachometer.yaml | 137 ++++++++++++++++++ > > 1 file changed, 137 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml > > > > diff --git a/Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml b/Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml > > new file mode 100644 > > index 000000000000..b84076a4a338 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml > > @@ -0,0 +1,137 @@ > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > > +%YAML 1.2 > > +--- > > + > > +$id: http://devicetree.org/schemas/hwmon/aspeed,ast2600-pwm-tachometer.yaml# > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > + > > +title: ASPEED AST2600 PWM and Fan Tacho controller device driver > > + > > +maintainers: > > + - Ryan Chen <ryan_chen@aspeedtech.com> > > + > > +description: | > > + The ASPEED PWM controller can support upto 16 PWM outputs. The ASPEED Fan Tacho > > + controller can support upto 16 Fan tachometer inputs. > > + There can be upto 16 fans supported. Each fan can have one PWM output and > > + one Fan tach inputs. > > + > > +properties: > > + compatible: > > + const: aspeed,ast2600-pwm-tachometer > > + > > + "#address-cells": > > + const: 1 > > + > > + "#size-cells": > > + const: 0 > > + > > + "#cooling-cells": > > + const: 2 > > + > > + reg: > > + description: > > + Address and length of the register set for the device. > > No need for generic descriptions. That's every 'reg'. > > What you need is how many entries and what each one is if more than 1. > If only 1, then just 'maxItems: 1' > > > + > > + clocks: > > + description: > > + phandle to clock provider with the clock number in the second cell > > Same here. > > > + > > + resets: > > + description: > > + phandle to reset controller with the reset number in the second cell > > And here. > > > + > > +patternProperties: > > + "@[0-9]+$": > > If every node is a fan and there are up to 16: > > ^fan@[0-9a-f]$ > I will update these in v3 patch set. > > + type: object > > + description: > > + Under fan subnode there can upto 16 child nodes, with each child node > > + representing a fan. There are 16 fans each fan can have one PWM port and one > > + Fan tach inputs. > > + For PWM port can be configured cooling-levels to create cooling device. > > + Cooling device could be bound to a thermal zone for the thermal control. > > + > > + properties: > > + reg: > > + minimum: 0 > > + maximum: 15 > > + description: > > + This property identify the PWM control channel of this fan. > > + > > + fan-tach-ch: > > + $ref: /schemas/types.yaml#/definitions/uint8 > > + minimum: 0 > > + maximum: 15 > > + description: > > + This property identify the fan tach input channel. > > + > > + pulses-per-revolution: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + default: 2 > > + minimum: 1 > > + description: > > + Specify tacho pulse per revolution of the fan. > > + > > + cooling-levels: > > + description: > > + PWM duty cycle values in a range from 0 to 255 > > + which correspond to thermal cooling states. > > + > > + aspeed,pwm-freq: > > + $ref: /schemas/types.yaml#/definitions/uint32 > > + default: 25000 > > + minimum: 24 > > + maximum: 780000 > > + description: > > + Specify the frequency of PWM. > > Units? Use a unit suffix and then drop the $ref. > I'll change it to pwm-freq-hz. > > + > > + aspeed,inverse-pin: > > + type: boolean > > + description: > > + Inverse PWM output signal. > > + > > + aspeed,falling-point: > > + $ref: /schemas/types.yaml#/definitions/uint8 > > + default: 10 > > + minimum: 0 > > + maximum: 255 > > 0-255 is already the range of uint8, so drop. > I'll drop it in v3. Thanks, Troy Lee > > + description: > > + Initialize the pulse width. > > + > > + required: > > + - fan-tach-ch > > + - reg > > + > > + additionalProperties: true > > + > > +required: > > + - compatible > > + - reg > > + > > +additionalProperties: false > > + > > +examples: > > + - | > > + pwm_tacho: pwm-tacho-controller@1e610000 { > > + compatible = "aspeed,ast2600-pwm-tachometer"; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + reg = <0x1e610000 0x100>; > > + > > + fan@1 { > > + reg = <0x00>; > > + aspeed,pwm-freq = <25000>; > > + cooling-levels = /bits/ 8 <125 151 177 203 229 255>; > > + fan-tach-ch = /bits/ 8 <0x00>; > > + pulses-per-revolution = <2>; > > + }; > > + > > + fan@2 { > > + reg = <0x01>; > > + aspeed,pwm-freq = <25000>; > > + cooling-levels = /bits/ 8 <125 151 177 203 229 255>; > > + fan-tach-ch = /bits/ 8 <0x01>; > > + pulses-per-revolution = <2>; > > + }; > > + }; > > +... > > -- > > 2.25.1 > >
diff --git a/Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml b/Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml new file mode 100644 index 000000000000..b84076a4a338 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml @@ -0,0 +1,137 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- + +$id: http://devicetree.org/schemas/hwmon/aspeed,ast2600-pwm-tachometer.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ASPEED AST2600 PWM and Fan Tacho controller device driver + +maintainers: + - Ryan Chen <ryan_chen@aspeedtech.com> + +description: | + The ASPEED PWM controller can support upto 16 PWM outputs. The ASPEED Fan Tacho + controller can support upto 16 Fan tachometer inputs. + There can be upto 16 fans supported. Each fan can have one PWM output and + one Fan tach inputs. + +properties: + compatible: + const: aspeed,ast2600-pwm-tachometer + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + "#cooling-cells": + const: 2 + + reg: + description: + Address and length of the register set for the device. + + clocks: + description: + phandle to clock provider with the clock number in the second cell + + resets: + description: + phandle to reset controller with the reset number in the second cell + +patternProperties: + "@[0-9]+$": + type: object + description: + Under fan subnode there can upto 16 child nodes, with each child node + representing a fan. There are 16 fans each fan can have one PWM port and one + Fan tach inputs. + For PWM port can be configured cooling-levels to create cooling device. + Cooling device could be bound to a thermal zone for the thermal control. + + properties: + reg: + minimum: 0 + maximum: 15 + description: + This property identify the PWM control channel of this fan. + + fan-tach-ch: + $ref: /schemas/types.yaml#/definitions/uint8 + minimum: 0 + maximum: 15 + description: + This property identify the fan tach input channel. + + pulses-per-revolution: + $ref: /schemas/types.yaml#/definitions/uint32 + default: 2 + minimum: 1 + description: + Specify tacho pulse per revolution of the fan. + + cooling-levels: + description: + PWM duty cycle values in a range from 0 to 255 + which correspond to thermal cooling states. + + aspeed,pwm-freq: + $ref: /schemas/types.yaml#/definitions/uint32 + default: 25000 + minimum: 24 + maximum: 780000 + description: + Specify the frequency of PWM. + + aspeed,inverse-pin: + type: boolean + description: + Inverse PWM output signal. + + aspeed,falling-point: + $ref: /schemas/types.yaml#/definitions/uint8 + default: 10 + minimum: 0 + maximum: 255 + description: + Initialize the pulse width. + + required: + - fan-tach-ch + - reg + + additionalProperties: true + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + pwm_tacho: pwm-tacho-controller@1e610000 { + compatible = "aspeed,ast2600-pwm-tachometer"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1e610000 0x100>; + + fan@1 { + reg = <0x00>; + aspeed,pwm-freq = <25000>; + cooling-levels = /bits/ 8 <125 151 177 203 229 255>; + fan-tach-ch = /bits/ 8 <0x00>; + pulses-per-revolution = <2>; + }; + + fan@2 { + reg = <0x01>; + aspeed,pwm-freq = <25000>; + cooling-levels = /bits/ 8 <125 151 177 203 229 255>; + fan-tach-ch = /bits/ 8 <0x01>; + pulses-per-revolution = <2>; + }; + }; +...
We add binding for supporting a new AST2600 PWM/Fan hwmon driver. Changes since v1: - dt binding with DT schema format Signed-off-by: Troy Lee <troy_lee@aspeedtech.com> --- .../hwmon/aspeed,ast2600-pwm-tachometer.yaml | 137 ++++++++++++++++++ 1 file changed, 137 insertions(+) create mode 100644 Documentation/devicetree/bindings/hwmon/aspeed,ast2600-pwm-tachometer.yaml