new file mode 100644
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "qca9563_tplink_eap2x5_1port.dtsi"
+
+/ {
+ compatible = "tplink,eap225-v3", "qca,qca9563";
+ model = "TP-Link EAP225 v3";
+
+ aliases {
+ led-boot = &led_status_green;
+ led-failsafe = &led_status_amber;
+ led-running = &led_status_green;
+ led-upgrade = &led_status_amber;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status_green: status_green {
+ label = "tp-link:green:status";
+ gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ led_status_amber: status_amber {
+ label = "tp-link:amber:status";
+ gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
@@ -38,6 +38,7 @@ ath79_setup_interfaces()
pisen,wmb001n|\
pisen,wmm003n|\
siemens,ws-ap3610|\
+ tplink,eap225-v3|\
tplink,eap225-outdoor-v1|\
tplink,eap245-v1|\
tplink,cpe210-v2|\
@@ -194,6 +194,7 @@ case "$FIRMWARE" in
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
+ tplink,eap225-v3|\
tplink,eap225-outdoor-v1)
caldata_extract "art" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) +1)
@@ -372,6 +372,15 @@ define Device/tplink_eap2x5_1port
IMAGE/factory.bin := append-rootfs | tplink-safeloader factory | pad-extra 128
endef
+define Device/tplink_eap225-v3
+ $(Device/tplink_eap2x5_1port)
+ DEVICE_MODEL := EAP225
+ DEVICE_VARIANT := v3
+ TPLINK_BOARD_ID := EAP225-V3
+ DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct
+endef
+TARGET_DEVICES += tplink_eap225-v3
+
define Device/tplink_eap225-outdoor-v1
$(Device/tplink_eap2x5_1port)
DEVICE_MODEL := EAP225-Outdoor
@@ -1291,6 +1291,34 @@ static struct device_info boards[] = {
.last_sysupgrade_partition = "file-system"
},
+ /** Firmware layout for the EAP225 v3 */
+ {
+ .id = "EAP225-V3",
+ .support_list =
+ "SupportList:\r\n"
+ "EAP225(TP-Link|UN|AC1350-D):3.0\r\n",
+ .soft_ver = NULL,
+ .soft_ver_compat_level = 1,
+
+ .partitions = {
+ {"fs-uboot", 0x00000, 0x20000},
+ {"partition-table", 0x20000, 0x02000},
+ {"default-mac", 0x30000, 0x01000},
+ {"support-list", 0x31000, 0x00100},
+ {"product-info", 0x31100, 0x00400},
+ {"soft-version", 0x32000, 0x00100},
+ {"firmware", 0x40000, 0xd80000},
+ {"user-config", 0xdc0000, 0x30000},
+ {"mutil-log", 0xf30000, 0x80000},
+ {"oops", 0xfb0000, 0x40000},
+ {"radio", 0xff0000, 0x10000},
+ {NULL, 0, 0}
+ },
+
+ .first_sysupgrade_partition = "os-image",
+ .last_sysupgrade_partition = "file-system"
+ },
+
/** Firmware layout for the EAP225-Outdoor v1 */
{
.id = "EAP225-OUTDOOR-V1",
TP-Link EAP225 v3 is an AC1350 (802.11ac Wave-2) ceiling mount access point. Device specifications: * SoC: QCA9563 @ 775MHz * RAM: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n, 3x3 * Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MINO * Ethernet (AR8033): 1× 1GbE, 803.2at PoE Flashing instructions: * ssh into target device and run `cliclientd stopcs` * Upgrade with factory image via web interface Debricking: * Serial port can be soldered on PCB J3 (1: TXD, 2: RXD, 3: GND, 4: VCC) * Bridge unpopulated resistors R225 (TXD) and R237 (RXD). Do NOT bridge R230. * Use 3.3V, 115200 baud, 8n1 * Interrupt bootloader by holding CTRL+B during boot * tftp initramfs to flash via LuCI web interface MAC addresses: MAC address (as on device label) is stored in device info partition at an offset of 8 bytes. ath9k device has same address as ethernet, ath10k uses address incremented by 1. From OEM boot log: Using interface ath0 with hwaddr b0:...:3e and ssid "..." Using interface ath10 with hwaddr b0:...:3f and ssid "..." Tested by forum user blinkstar88 Signed-off-by: Sander Vanheule <sander@svanheule.net> --- .../ath79/dts/qca9563_tplink_eap225-v3.dts | 31 +++++++++++++++++++ .../generic/base-files/etc/board.d/02_network | 1 + .../etc/hotplug.d/firmware/11-ath10k-caldata | 1 + target/linux/ath79/image/generic-tp-link.mk | 9 ++++++ tools/firmware-utils/src/tplink-safeloader.c | 28 +++++++++++++++++ 5 files changed, 70 insertions(+) create mode 100644 target/linux/ath79/dts/qca9563_tplink_eap225-v3.dts