Message ID | 20191224165108.2836-4-erosca@de.adit-jv.com |
---|---|
State | Accepted |
Commit | 4f731c795d75aee548f6886f4f0da0a49a99354d |
Delegated to: | Tom Rini |
Headers | show |
Series | cmd: dtimg: Rename to adtimg and refactor usage style | expand |
Hi Eugeniu, On Tue, 24 Dec 2019 at 09:52, Eugeniu Rosca <roscaeugeniu@gmail.com> wrote: > > Trying to extend 'adtimg' functionality [1], we've been severely hit > by a major limitation in the command's usage scheme. Specifically, the > command's user interface appears to be too centric to getting the > DTB/DTBO entry [3] based on the index of the desired DT in the image, > which makes it really difficult retrieving the DT entry based on > alternative criteria (e.g. filtering by id/rev fields), the > latter being demanded by real life customer use-cases [1]. > > This went to the point of receiving below feedback from Sam [2]: > > -- snip -- > As for 'dtimg' command: after giving it some thought, I think not much > people using it yet. So in this particular case I don't have some > strong preference, and if you think the 'dtimg' interface is ugly, and > it overcomes "don't break interfaces" rule, maybe now is a good time > to rework it (before it gets widely used). > -- snip -- > > Given the above, rework the usage pattern from [4] to [5], in order to > allow an intuitive enablement of "by id|rev" DT search [6]. > > [1] https://patchwork.ozlabs.org/cover/1202575/ > ("cmd: dtimg: Enhance with --id and --rev options (take #1)") > [2] https://patchwork.ozlabs.org/patch/1182207/#2317020 > [3] https://source.android.com/devices/architecture/dto/partitions > [4] Old usage > adtimg dump <addr> - Print image contents > adtimg start <addr> <index> <varname> - Get DT address by index > adtimg size <addr> <index> <varname> - Get DT size by index > > [5] New usage > adtimg addr <addr> - Set image location to <addr> > adtimg dump - Print out image contents > adtimg get dt --index=<i> [avar [svar]] - Get DT address and size by index > > [6] Soon-to-be-provided "by id|rev" add-on functionality > adtimg get dt --id=<id> --rev=<rev> [avar [svar [ivar]]] > - Get DT address/size/index by id|rev fields > > Cc: Sam Protsenko <semen.protsenko@linaro.org> > Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> > --- > cmd/adtimg.c | 217 +++++++++++++++++++++++++++++++++++++-------------- > 1 file changed, 158 insertions(+), 59 deletions(-) Can you please add a test for this command? Regards, Simon
Hi Simon, On Wed, Jan 08, 2020 at 10:39:34AM -0700, Simon Glass wrote: > On Tue, 24 Dec 2019 at 09:52, Eugeniu Rosca <roscaeugeniu@gmail.com> wrote: > > [5] New usage > > adtimg addr <addr> - Set image location to <addr> > > adtimg dump - Print out image contents > > adtimg get dt --index=<i> [avar [svar]] - Get DT address and size by index > > > > [6] Soon-to-be-provided "by id|rev" add-on functionality > > adtimg get dt --id=<id> --rev=<rev> [avar [svar [ivar]]] > > - Get DT address/size/index by id|rev fields > > > > Cc: Sam Protsenko <semen.protsenko@linaro.org> > > Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> > > --- > > cmd/adtimg.c | 217 +++++++++++++++++++++++++++++++++++++-------------- > > 1 file changed, 158 insertions(+), 59 deletions(-) > > Can you please add a test for this command? Many thanks for the inputs. Two questions: - The binary which adtimg operates on is generated by means of a host tooling [1] which is actively developed and hence continuously incorporates new features. Only the recent versions of [1] (obsoleting Debian packages like [2]) may be used to generate a valid test image for the adtimg U-Boot command. I think Sam found an elegant solution in [3] to make the hex dump of the test image part of the test itself, as opposed to below: - require the users to install the correct tool version on the host, - embed the required tool version into U-Boot and track its version, I plan to go the same route and just want to make sure we all agree on the approach just described. - Since this series is already reviewed, are you fine if the test is submitted in a follow-up series, accompanied by a number of new adtimg features sitting in my queue? [1] https://android.googlesource.com/platform/system/tools/mkbootimg/ [2] https://packages.debian.org/sid/android-tools-mkbootimg [3] https://patchwork.ozlabs.org/patch/1215287/
On Tue, Dec 24, 2019 at 05:51:08PM +0100, Eugeniu Rosca wrote: > Trying to extend 'adtimg' functionality [1], we've been severely hit > by a major limitation in the command's usage scheme. Specifically, the > command's user interface appears to be too centric to getting the > DTB/DTBO entry [3] based on the index of the desired DT in the image, > which makes it really difficult retrieving the DT entry based on > alternative criteria (e.g. filtering by id/rev fields), the > latter being demanded by real life customer use-cases [1]. > > This went to the point of receiving below feedback from Sam [2]: > > -- snip -- > As for 'dtimg' command: after giving it some thought, I think not much > people using it yet. So in this particular case I don't have some > strong preference, and if you think the 'dtimg' interface is ugly, and > it overcomes "don't break interfaces" rule, maybe now is a good time > to rework it (before it gets widely used). > -- snip -- > > Given the above, rework the usage pattern from [4] to [5], in order to > allow an intuitive enablement of "by id|rev" DT search [6]. > > [1] https://patchwork.ozlabs.org/cover/1202575/ > ("cmd: dtimg: Enhance with --id and --rev options (take #1)") > [2] https://patchwork.ozlabs.org/patch/1182207/#2317020 > [3] https://source.android.com/devices/architecture/dto/partitions > [4] Old usage > adtimg dump <addr> - Print image contents > adtimg start <addr> <index> <varname> - Get DT address by index > adtimg size <addr> <index> <varname> - Get DT size by index > > [5] New usage > adtimg addr <addr> - Set image location to <addr> > adtimg dump - Print out image contents > adtimg get dt --index=<i> [avar [svar]] - Get DT address and size by index > > [6] Soon-to-be-provided "by id|rev" add-on functionality > adtimg get dt --id=<id> --rev=<rev> [avar [svar [ivar]]] > - Get DT address/size/index by id|rev fields > > Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> > Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> Applied to u-boot/master, thanks!
Hi Tom, On Fri, Jan 10, 2020 at 04:50:52PM -0500, Tom Rini wrote: > On Tue, Dec 24, 2019 at 05:51:08PM +0100, Eugeniu Rosca wrote: > > Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> > > Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> > > Applied to u-boot/master, thanks! Thanks for merging!
Hi Eugeniu, > From: U-Boot <u-boot-bounces@lists.denx.de> On Behalf Of Eugeniu Rosca > Sent: samedi 11 janvier 2020 00:30 > > Hi Tom, > > On Fri, Jan 10, 2020 at 04:50:52PM -0500, Tom Rini wrote: > > On Tue, Dec 24, 2019 at 05:51:08PM +0100, Eugeniu Rosca wrote: > > > Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> > > > Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> > > > > Applied to u-boot/master, thanks! > > Thanks for merging! For the planned update of the command adtimg: > [6] Soon-to-be-provided "by id|rev" add-on functionality adtimg get dt > --id=<id> --rev=<rev> [avar [svar [ivar]]] > - Get DT address/size/index by id|rev fields Do you have plan to upstream this code or it is available in downstream ? Because stm32mp1 platform needs this feature We code in downstream [1] based on v2020.01 almost the same command but based on the old usage = [2] dtimg getindex <addr> <board_id> <board_rev> [varname] - get index of FDT in the image, by board identifier and revision <addr>: image address in RAM, in hex <board_id>: board identifier <board_rev>: board revision (0 if not used) [varname]: name of variable where to store index of FDT So if you have nothing ready, I can update my code with your proposed parameters. [1] https://github.com/STMicroelectronics/u-boot/blob/v2020.01-stm32mp/cmd/dtimg.c [2] https://github.com/STMicroelectronics/u-boot/commit/21b57a166e73a8457d4caea6a1d37f1f3fda3d45 > -- > Best Regards, > Eugeniu Best Regards Patrick
Hi Patrick, On Fri, Jul 03, 2020 at 04:40:28PM +0000, Patrick DELAUNAY wrote: > > From: U-Boot <u-boot-bounces@lists.denx.de> On Behalf Of Eugeniu Rosca > > Sent: samedi 11 janvier 2020 00:30 > > > > Hi Tom, > > > > On Fri, Jan 10, 2020 at 04:50:52PM -0500, Tom Rini wrote: > > > On Tue, Dec 24, 2019 at 05:51:08PM +0100, Eugeniu Rosca wrote: > > > > Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> > > > > Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> > > > > > > Applied to u-boot/master, thanks! > > > > Thanks for merging! > > For the planned update of the command adtimg: > > > [6] Soon-to-be-provided "by id|rev" add-on functionality adtimg get dt > > --id=<id> --rev=<rev> [avar [svar [ivar]]] > > - Get DT address/size/index by id|rev fields > > Do you have plan to upstream this code or it is available in downstream ? > > Because stm32mp1 platform needs this feature Good to hear that the features are used by people out there. > We code in downstream [1] based on v2020.01 almost the same command > but based on the old usage = [2] After a quick look, this is certainly missing the latest vanilla patches, so is out of sync with mainline. > dtimg getindex <addr> <board_id> <board_rev> [varname] > - get index of FDT in the image, by board identifier and revision > <addr>: image address in RAM, in hex > <board_id>: board identifier > <board_rev>: board revision (0 if not used) > [varname]: name of variable where to store index of FDT > > So if you have nothing ready, I can update my code with your proposed parameters. > > [1] https://github.com/STMicroelectronics/u-boot/blob/v2020.01-stm32mp/cmd/dtimg.c > [2] https://github.com/STMicroelectronics/u-boot/commit/21b57a166e73a8457d4caea6a1d37f1f3fda3d45 You would need to rebase these commits first. A quicker route is to just take my patches available below: https://github.com/erosca/u-boot/commits/master_adtimg_id_rev These have been extensively tested and are now running in development/production systems for months w/o any issues. Do you have any comments concerning the two commits below? https://github.com/erosca/u-boot/commit/936a08faaf3f485527e2d1cfb8a53dcf44e17b3a https://github.com/erosca/u-boot/commit/e37d090dabb6973762376adca5ae10292ca3ba3d
Thanks, > From: Eugeniu Rosca <erosca@de.adit-jv.com> > Sent: lundi 6 juillet 2020 08:47 > > Hi Patrick, > > On Fri, Jul 03, 2020 at 04:40:28PM +0000, Patrick DELAUNAY wrote: > > > From: U-Boot <u-boot-bounces@lists.denx.de> On Behalf Of Eugeniu > > > Rosca > > > Sent: samedi 11 janvier 2020 00:30 > > > > > > Hi Tom, > > > > > > On Fri, Jan 10, 2020 at 04:50:52PM -0500, Tom Rini wrote: > > > > On Tue, Dec 24, 2019 at 05:51:08PM +0100, Eugeniu Rosca wrote: > > > > > Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> > > > > > Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org> > > > > > > > > Applied to u-boot/master, thanks! > > > > > > Thanks for merging! > > > > For the planned update of the command adtimg: > > > > > [6] Soon-to-be-provided "by id|rev" add-on functionality adtimg get > > > dt --id=<id> --rev=<rev> [avar [svar [ivar]]] > > > - Get DT address/size/index by id|rev fields > > > > Do you have plan to upstream this code or it is available in downstream ? > > > > Because stm32mp1 platform needs this feature > > Good to hear that the features are used by people out there. > > > We code in downstream [1] based on v2020.01 almost the same command > > but based on the old usage = [2] > > After a quick look, this is certainly missing the latest vanilla patches, so is out of > sync with mainline. > > > dtimg getindex <addr> <board_id> <board_rev> [varname] > > - get index of FDT in the image, by board identifier and revision > > <addr>: image address in RAM, in hex > > <board_id>: board identifier > > <board_rev>: board revision (0 if not used) > > [varname]: name of variable where to store index of FDT > > > > So if you have nothing ready, I can update my code with your proposed > parameters. > > > > [1] > > https://github.com/STMicroelectronics/u-boot/blob/v2020.01-stm32mp/cmd > > /dtimg.c [2] > > https://github.com/STMicroelectronics/u-boot/commit/21b57a166e73a8457d > > 4caea6a1d37f1f3fda3d45 > > You would need to rebase these commits first. > A quicker route is to just take my patches available below: > https://github.com/erosca/u-boot/commits/master_adtimg_id_rev > > These have been extensively tested and are now running in > development/production systems for months w/o any issues. > > Do you have any comments concerning the two commits below? > https://github.com/erosca/u- > boot/commit/936a08faaf3f485527e2d1cfb8a53dcf44e17b3a > https://github.com/erosca/u- > boot/commit/e37d090dabb6973762376adca5ae10292ca3ba3d I check the 2 patches, they seems OK. I just surprized by the '--' for the command parameter because it is unusual in U-Boot commands. It wasn't enough to have .....<parameter>=<val> as other command (unzip for example) but it is perhaps to late to change again the commands adtimg and it is aligned with "abootimg.c" For information, I will activate the command ADTIMG for stm32mp32 [1] and update the stm32mp1 downstream android bootcmd to use when they will be available. But I have don't yet tested them We do you plan to rebase and upstream these 2 commits ? [1] = http://patchwork.ozlabs.org/project/uboot/patch/20200706130046.22446-1-patrick.delaunay@st.com/ > -- > Best regards, > Eugeniu Rosca Best regards, Patrick
diff --git a/cmd/adtimg.c b/cmd/adtimg.c index 22b4f5e1a83f..60bb01c3498a 100644 --- a/cmd/adtimg.c +++ b/cmd/adtimg.c @@ -2,18 +2,22 @@ /* * (C) Copyright 2018 Linaro Ltd. * Sam Protsenko <semen.protsenko@linaro.org> + * Eugeniu Rosca <rosca.eugeniu@gmail.com> */ #include <env.h> #include <image-android-dt.h> #include <common.h> -enum cmd_adtimg_info { - CMD_ADTIMG_START = 0, - CMD_ADTIMG_SIZE, -}; +#define OPT_INDEX "--index" -static int do_adtimg_dump(cmd_tbl_t *cmdtp, int flag, int argc, +/* + * Current/working DTB/DTBO Android image address. + * Similar to 'working_fdt' variable in 'fdt' command. + */ +static ulong working_img; + +static int do_adtimg_addr(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { char *endp; @@ -24,86 +28,185 @@ static int do_adtimg_dump(cmd_tbl_t *cmdtp, int flag, int argc, hdr_addr = simple_strtoul(argv[1], &endp, 16); if (*endp != '\0') { - printf("Error: Wrong image address\n"); + printf("Error: Wrong image address '%s'\n", argv[1]); return CMD_RET_FAILURE; } - if (!android_dt_check_header(hdr_addr)) { - printf("Error: DT image header is incorrect\n"); + /* + * Allow users to set an address prior to copying the DTB/DTBO + * image to that same address, i.e. skip header verification. + */ + + working_img = hdr_addr; + return CMD_RET_SUCCESS; +} + +static int adtimg_check_working_img(void) +{ + if (!working_img) { + printf("Error: Please, call 'adtimg addr <addr>'. Aborting!\n"); return CMD_RET_FAILURE; } - android_dt_print_contents(hdr_addr); + if (!android_dt_check_header(working_img)) { + printf("Error: Invalid image header at 0x%lx\n", working_img); + return CMD_RET_FAILURE; + } return CMD_RET_SUCCESS; } -static int adtimg_get_fdt(int argc, char * const argv[], - enum cmd_adtimg_info cmd) +static int do_adtimg_dump(cmd_tbl_t *cmdtp, int flag, int argc, + char * const argv[]) { - ulong hdr_addr; - u32 index; - char *endp; - ulong fdt_addr; - u32 fdt_size; - char buf[65]; - - if (argc != 4) + if (argc != 1) return CMD_RET_USAGE; - hdr_addr = simple_strtoul(argv[1], &endp, 16); - if (*endp != '\0') { - printf("Error: Wrong image address\n"); + if (adtimg_check_working_img() != CMD_RET_SUCCESS) + return CMD_RET_FAILURE; + + android_dt_print_contents(working_img); + + return CMD_RET_SUCCESS; +} + +static int adtimg_getopt_u32(char * const opt, char * const name, u32 *optval) +{ + char *endp, *str; + u32 val; + + if (!opt || !name || !optval) + return CMD_RET_FAILURE; + + str = strchr(opt, '='); + if (!str) { + printf("Error: Option '%s' not followed by '='\n", name); return CMD_RET_FAILURE; } - if (!android_dt_check_header(hdr_addr)) { - printf("Error: DT image header is incorrect\n"); + if (*++str == '\0') { + printf("Error: Option '%s=' not followed by value\n", name); return CMD_RET_FAILURE; } - index = simple_strtoul(argv[2], &endp, 0); + val = simple_strtoul(str, &endp, 0); if (*endp != '\0') { - printf("Error: Wrong index\n"); + printf("Error: Wrong integer value '%s=%s'\n", name, str); return CMD_RET_FAILURE; } - if (!android_dt_get_fdt_by_index(hdr_addr, index, &fdt_addr, &fdt_size)) + *optval = val; + return CMD_RET_SUCCESS; +} + +static int adtimg_getopt_index(int argc, char * const argv[], u32 *index, + char **avar, char **svar) +{ + int ret; + + if (!argv || !avar || !svar) return CMD_RET_FAILURE; - switch (cmd) { - case CMD_ADTIMG_START: - snprintf(buf, sizeof(buf), "%lx", fdt_addr); - break; - case CMD_ADTIMG_SIZE: - snprintf(buf, sizeof(buf), "%x", fdt_size); - break; - default: - printf("Error: Unknown cmd_adtimg_info value: %d\n", cmd); + if (argc > 3) { + printf("Error: Unexpected argument '%s'\n", argv[3]); return CMD_RET_FAILURE; } - env_set(argv[3], buf); + ret = adtimg_getopt_u32(argv[0], OPT_INDEX, index); + if (ret != CMD_RET_SUCCESS) + return ret; + + if (argc > 1) + *avar = argv[1]; + if (argc > 2) + *svar = argv[2]; return CMD_RET_SUCCESS; } -static int do_adtimg_start(cmd_tbl_t *cmdtp, int flag, int argc, - char * const argv[]) +static int adtimg_get_dt_by_index(int argc, char * const argv[]) { - return adtimg_get_fdt(argc, argv, CMD_ADTIMG_START); + ulong addr; + u32 index, size; + int ret; + char *avar = NULL, *svar = NULL; + + ret = adtimg_getopt_index(argc, argv, &index, &avar, &svar); + if (ret != CMD_RET_SUCCESS) + return ret; + + if (!android_dt_get_fdt_by_index(working_img, index, &addr, &size)) + return CMD_RET_FAILURE; + + if (avar && svar) { + ret = env_set_hex(avar, addr); + if (ret) { + printf("Error: Can't set '%s' to 0x%lx\n", avar, addr); + return CMD_RET_FAILURE; + } + ret = env_set_hex(svar, size); + if (ret) { + printf("Error: Can't set '%s' to 0x%x\n", svar, size); + return CMD_RET_FAILURE; + } + } else if (avar) { + ret = env_set_hex(avar, addr); + if (ret) { + printf("Error: Can't set '%s' to 0x%lx\n", avar, addr); + return CMD_RET_FAILURE; + } + printf("0x%x (%d)\n", size, size); + } else { + printf("0x%lx, 0x%x (%d)\n", addr, size, size); + } + + return CMD_RET_SUCCESS; } -static int do_adtimg_size(cmd_tbl_t *cmdtp, int flag, int argc, - char * const argv[]) +static int adtimg_get_dt(int argc, char * const argv[]) { - return adtimg_get_fdt(argc, argv, CMD_ADTIMG_SIZE); + if (argc < 2) { + printf("Error: No options passed to '%s'\n", argv[0]); + return CMD_RET_FAILURE; + } + + /* Strip off leading 'dt' command argument */ + argc--; + argv++; + + if (!strncmp(argv[0], OPT_INDEX, sizeof(OPT_INDEX) - 1)) + return adtimg_get_dt_by_index(argc, argv); + + printf("Error: Option '%s' not supported\n", argv[0]); + return CMD_RET_FAILURE; +} + +static int do_adtimg_get(cmd_tbl_t *cmdtp, int flag, int argc, + char * const argv[]) +{ + if (argc < 2) { + printf("Error: No arguments passed to '%s'\n", argv[0]); + return CMD_RET_FAILURE; + } + + if (adtimg_check_working_img() != CMD_RET_SUCCESS) + return CMD_RET_FAILURE; + + /* Strip off leading 'get' command argument */ + argc--; + argv++; + + if (!strcmp(argv[0], "dt")) + return adtimg_get_dt(argc, argv); + + printf("Error: Wrong argument '%s'\n", argv[0]); + return CMD_RET_FAILURE; } static cmd_tbl_t cmd_adtimg_sub[] = { - U_BOOT_CMD_MKENT(dump, 2, 0, do_adtimg_dump, "", ""), - U_BOOT_CMD_MKENT(start, 4, 0, do_adtimg_start, "", ""), - U_BOOT_CMD_MKENT(size, 4, 0, do_adtimg_size, "", ""), + U_BOOT_CMD_MKENT(addr, CONFIG_SYS_MAXARGS, 1, do_adtimg_addr, "", ""), + U_BOOT_CMD_MKENT(dump, CONFIG_SYS_MAXARGS, 1, do_adtimg_dump, "", ""), + U_BOOT_CMD_MKENT(get, CONFIG_SYS_MAXARGS, 1, do_adtimg_get, "", ""), }; static int do_adtimg(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) @@ -127,17 +230,13 @@ static int do_adtimg(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) U_BOOT_CMD( adtimg, CONFIG_SYS_MAXARGS, 0, do_adtimg, "manipulate dtb/dtbo Android image", - "dump <addr>\n" - " - parse specified image and print its structure info\n" - " <addr>: image address in RAM, in hex\n" - "adtimg start <addr> <index> <varname>\n" - " - get address (hex) of FDT in the image, by index\n" - " <addr>: image address in RAM, in hex\n" - " <index>: index of desired FDT in the image\n" - " <varname>: name of variable where to store address of FDT\n" - "adtimg size <addr> <index> <varname>\n" - " - get size (hex, bytes) of FDT in the image, by index\n" - " <addr>: image address in RAM, in hex\n" - " <index>: index of desired FDT in the image\n" - " <varname>: name of variable where to store size of FDT" + "addr <addr> - Set image location to <addr>\n" + "adtimg dump - Print out image contents\n" + "adtimg get dt --index=<index> [avar [svar]] - Get DT address/size by index\n" + "\n" + "Legend:\n" + " - <addr>: DTB/DTBO image address (hex) in RAM\n" + " - <index>: index (hex/dec) of desired DT in the image\n" + " - <avar>: variable name to contain DT address (hex)\n" + " - <svar>: variable name to contain DT size (hex)" );
Trying to extend 'adtimg' functionality [1], we've been severely hit by a major limitation in the command's usage scheme. Specifically, the command's user interface appears to be too centric to getting the DTB/DTBO entry [3] based on the index of the desired DT in the image, which makes it really difficult retrieving the DT entry based on alternative criteria (e.g. filtering by id/rev fields), the latter being demanded by real life customer use-cases [1]. This went to the point of receiving below feedback from Sam [2]: -- snip -- As for 'dtimg' command: after giving it some thought, I think not much people using it yet. So in this particular case I don't have some strong preference, and if you think the 'dtimg' interface is ugly, and it overcomes "don't break interfaces" rule, maybe now is a good time to rework it (before it gets widely used). -- snip -- Given the above, rework the usage pattern from [4] to [5], in order to allow an intuitive enablement of "by id|rev" DT search [6]. [1] https://patchwork.ozlabs.org/cover/1202575/ ("cmd: dtimg: Enhance with --id and --rev options (take #1)") [2] https://patchwork.ozlabs.org/patch/1182207/#2317020 [3] https://source.android.com/devices/architecture/dto/partitions [4] Old usage adtimg dump <addr> - Print image contents adtimg start <addr> <index> <varname> - Get DT address by index adtimg size <addr> <index> <varname> - Get DT size by index [5] New usage adtimg addr <addr> - Set image location to <addr> adtimg dump - Print out image contents adtimg get dt --index=<i> [avar [svar]] - Get DT address and size by index [6] Soon-to-be-provided "by id|rev" add-on functionality adtimg get dt --id=<id> --rev=<rev> [avar [svar [ivar]]] - Get DT address/size/index by id|rev fields Cc: Sam Protsenko <semen.protsenko@linaro.org> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> --- cmd/adtimg.c | 217 +++++++++++++++++++++++++++++++++++++-------------- 1 file changed, 158 insertions(+), 59 deletions(-)