| Message ID | alpine.DEB.2.00.1105181257370.2374@localhost6.localdomain6 |
|---|---|
| State | New |
| Headers | show |
On Thu, May 19, 2011 at 06:31:28PM +0100, Frank Hofmann wrote: > Hi, > > /me again ... > > Sorry that this took a little ... holidays. And work. And distractions... > > Anyway, here we go again, basic code to enable hibernation > (suspend-to-disk) on ARM platforms. > > Any comments highly welcome. > > > > To use this, you need sleep.S modifications for your SoC type (to > get __save/__restore_processor_state hooks). I've sent some of those > for illustration earlier, they haven't changed, I've not included > them here, so pick these changes up from: > > http://68.183.106.108/lists/linux-pm/msg24020.html > > The patch below only contains the _generic_ code. > > > This is tested on S5P6450 and OMAP3, with the sleep...S changes just > mentioned - check the archives for those. Works both with normal > swsusp and tuxonice (again, check the archives for the TOI > modification needed). > > > > Previously, I've reported OMAP3 video issues, after > resume-from-disk. That isn't fully solved (it's a driver issue) but > I've found a workaround: Trigger the resume from initramfs, after > loading a logo image into the framebuffer and switching it on. That > gets everything back without corruptions / wrong LCD > reinitialization. > > The OMAP video seems a bit of a diva; I've got one board type on > which suspend/resume work perfectly but the omapdss driver spits out > thousands of error interrupts during system startup (before the > image is loaded), and the other board where all that is fine but the > restore somehow garbles the LCD clocking (but the driver's sysfs > files claim it's the same). > > > In short: This stuff really works now, for all I can say. And adding > support for new type of ARM SoC doesn't touch the basic / generic > code at all anymore either. > > > > > Anyway ... > About the patch, changes vs. all previous suggestions: > > * Made the assembly sources as small as I responsibly could ;-) > They compile for thumb2 (but I haven't tested that yet) as well. > > * The page copy loop is now a C function. That also has the advantage > that one can use cpu_switch_mm() - a macro - there for swapper_pg_dir, > which makes resume via uswsusp ioctl or /sys/power/tuxonice/do_resume > possible (only tested the latter, though). > > * The SoC state save/restore is made to (re-)use the existing code in > sleep....S for the particular chip. > OMAP3 and S5P64xx are provided as examples of that. > > * The save/restore_processor_state() hooks are now used in the same way > as e.g. existing powerpc code uses them (to trigger lazy saves before > and perform cache flushes after). > > > Things that probably aren't perfect yet: > > * The code currently reserves a full page for the saved "core" state. > This is more than absolutely necessary; anyone think it's a problem ? > > * it sets aside another half a page of __nosavedata page for use as > temporary stack during the image copy (so that funcs can be called). > > Right now on ARM, that's not an issue because even with TuxOnIce in, > there's less than 20 bytes of nosave stuff, so can as well put the > rest of that page to good use ;-) > > * I'd love to get rid of the include/asm-generic/vmlinux.lds.h change, > as it seems that's not necessary in other architectures. > Without that, the code gives a link error when building vmlinux > though, and I'm unsure how to address that. > > * The "integration" with the CPU sleep code is rather "backdoorish". > While the hooks into ..._cpu_suspend aren't massive, and there's no > code duplication, it'd be nicer to eventually have a cleaner way. > > * An OMAPDSS restore troubleshooting HOWTO would be helpful ;-) > > > * The patch needs to be rebaselined against a current kernel; > any preferences which tree to base this on ? > > > > Thanks for all help with the little nits ! > FrankH. > arch/arm/Kconfig | 3 + > arch/arm/include/asm/memory.h | 1 + > arch/arm/include/asm/suspend.h | 6 ++ > arch/arm/kernel/cpu.c | 65 ++++++++++++++++++++++++++ > arch/arm/kernel/swsusp.S | 92 +++++++++++++++++++++++++++++++++++++ > arch/arm/kernel/vmlinux.lds.S | 3 +- > include/asm-generic/vmlinux.lds.h | 2 +- > 7 files changed, 170 insertions(+), 2 deletions(-) > > diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig > index 6b6786c..859dd86 100644 > --- a/arch/arm/Kconfig > +++ b/arch/arm/Kconfig > @@ -198,6 +198,9 @@ config VECTORS_BASE > config ARCH_HAS_CPU_IDLE_WAIT > def_bool y > > +config ARCH_HIBERNATION_POSSIBLE > + def_bool n > + > source "init/Kconfig" > > source "kernel/Kconfig.freezer" > diff --git a/arch/arm/include/asm/memory.h b/arch/arm/include/asm/memory.h > index 5421d82..23e93a6 100644 > --- a/arch/arm/include/asm/memory.h > +++ b/arch/arm/include/asm/memory.h > @@ -191,6 +191,7 @@ static inline void *phys_to_virt(unsigned long x) > */ > #define __pa(x) __virt_to_phys((unsigned long)(x)) > #define __va(x) ((void *)__phys_to_virt((unsigned long)(x))) > +#define __pa_symbol(x) __pa(RELOC_HIDE((unsigned long)(x),0)) > #define pfn_to_kaddr(pfn) __va((pfn) << PAGE_SHIFT) > > /* > diff --git a/arch/arm/include/asm/suspend.h b/arch/arm/include/asm/suspend.h > new file mode 100644 > index 0000000..7ab1fd2 > --- /dev/null > +++ b/arch/arm/include/asm/suspend.h > @@ -0,0 +1,6 @@ > +#ifndef __ASM_ARM_SUSPEND_H > +#define __ASM_ARM_SUSPEND_H > + > +static inline int arch_prepare_suspend(void) { return 0; } > + > +#endif /* __ASM_ARM_SUSPEND_H */ > diff --git a/arch/arm/kernel/cpu.c b/arch/arm/kernel/cpu.c > new file mode 100644 > index 0000000..764c8fa > --- /dev/null > +++ b/arch/arm/kernel/cpu.c > @@ -0,0 +1,65 @@ > +/* > + * Hibernation support specific for ARM > + * > + * Derived from work on ARM hibernation support by: > + * > + * Ubuntu project, hibernation support for mach-dove > + * Copyright (C) 2010 Nokia Corporation (Hiroshi Doyu) > + * Copyright (C) 2010 Texas Instruments, Inc. (Teerth Reddy et al.) > + * https://lkml.org/lkml/2010/6/18/4 > + * https://lists.linux-foundation.org/pipermail/linux-pm/2010-June/027422.html > + * https://patchwork.kernel.org/patch/96442/ > + * > + * Copyright (C) 2006 Rafael J. Wysocki <rjw@sisk.pl> > + * > + * License terms: GNU General Public License (GPL) version 2 > + */ > + > +#include <linux/mm.h> > +#include <linux/sched.h> > +#include <linux/suspend.h> > +#include <asm/tlbflush.h> > + > +extern const void __nosave_begin, __nosave_end; > + > +int pfn_is_nosave(unsigned long pfn) > +{ > + unsigned long nosave_begin_pfn = __pa_symbol(&__nosave_begin) >> PAGE_SHIFT; > + unsigned long nosave_end_pfn = PAGE_ALIGN(__pa_symbol(&__nosave_end)) >> PAGE_SHIFT; > + > + return (pfn >= nosave_begin_pfn) && (pfn < nosave_end_pfn); > +} > + > +void save_processor_state(void) > +{ > + flush_thread(); > +} > + > +void restore_processor_state(void) > +{ > + local_flush_tlb_all(); > +} > + > +u8 __swsusp_arch_ctx[PAGE_SIZE] __attribute__((aligned(PAGE_SIZE))); > +u8 __swsusp_resume_stk[PAGE_SIZE/2] __nosavedata; > + > +/* > + * The framework loads the hibernation image into this linked list, > + * for swsusp_arch_resume() to copy back to the proper destinations. > + * > + * To make this work if resume is triggered from initramfs, the > + * pagetables need to be switched to allow writes to kernel mem. > + */ > +void notrace __swsusp_arch_restore_prepare(void) > +{ > + cpu_switch_mm(__virt_to_phys(swapper_pg_dir), current->active_mm); > +} > + > +void notrace __swsusp_arch_restore_image(void) > +{ > + extern struct pbe *restore_pblist; > + struct pbe *pbe; > + > + for (pbe = restore_pblist; pbe; pbe = pbe->next) > + copy_page(pbe->orig_address, pbe->address); > +} > diff --git a/arch/arm/kernel/swsusp.S b/arch/arm/kernel/swsusp.S > new file mode 100644 > index 0000000..fb260a7 > --- /dev/null > +++ b/arch/arm/kernel/swsusp.S > @@ -0,0 +1,92 @@ > +/* > + * Hibernation support specific for ARM > + * > + * Based on work by: > + * > + * Ubuntu project, hibernation support for mach-dove, > + * Copyright (C) 2010 Nokia Corporation (Hiroshi Doyu) > + * Copyright (C) 2010 Texas Instruments, Inc. (Teerth Reddy et al.) > + * https://lkml.org/lkml/2010/6/18/4 > + * https://lists.linux-foundation.org/pipermail/linux-pm/2010-June/027422.html > + * https://patchwork.kernel.org/patch/96442/ > + * > + * Copyright (C) 2006 Rafael J. Wysocki <rjw@sisk.pl> > + * > + * License terms: GNU General Public License (GPL) version 2 > + */ > + > +#include <linux/linkage.h> > +#include <asm/memory.h> > +#include <asm/page.h> > +#include <asm/cache.h> > +#include <asm/ptrace.h> > + > +/* > + * Save the current CPU state before suspend / poweroff. > + */ > +ENTRY(swsusp_arch_suspend) > + ldr r0, =__swsusp_arch_ctx > + mrs r1, cpsr > + str r1, [r0], #4 /* CPSR */ > +ARM( msr cpsr_c, #SYSTEM_MODE ) > +THUMB( mov r2, #SYSTEM_MODE ) > +THUMB( msr cpsr_c, r2 ) For Thumb-2 kernels, you can use the cps instruction to change the CPU mode: cps #SYSTEM_MODE For ARM though, this instruction is only supported for ARMv6 and above, so it's best to keep the msr form for compatibility for that case. > + stm r0!, {r4-r12,lr} /* nonvolatile regs */ Since r12 is allowed to be corrupted across a function call, we probably don't need to save it. > + str sp, [r0], #4 > +ARM( msr cpsr_c, #SVC_MODE ) > +THUMB( mov r2, #SVC_MODE ) > +THUMB( msr cpsr_c, r2 ) > + mrs r2, spsr > + stm r0!, {r2,lr} /* SVC SPSR, SVC regs */ > + str sp, [r0], #4 > + msr cpsr, r1 /* restore mode at entry */ > + push {lr} > + bl __save_processor_state <aside> Structurally, we seem to have: swsusp_arch_suspend { /* save some processor state */ __save_processor_state(); swsusp_save(); } Is __save_processor_state() intended to encapsulate all the CPU-model- specific state saving? Excuse my ignorance of previous conversations... </aside> > + pop {lr} > + b swsusp_save > +ENDPROC(swsusp_arch_suspend) I'm not too familiar with the suspend/resume stuff, so I may be asking a dumb question here, but: Where do we save/restore r8_FIQ..r13_FIQ, r13_IRQ, r13_UND and r13_ABT? (I'm assuming there's no reason to save/restore r14 or SPSR for any exception mode, since we presumably aren't going to suspend/resume from inside an exception handler (?)) The exception stack pointers might conceivably be reinitialised to sane values on resume, without necessarily needing to save/restore them, providing my assumption in the previous paragraph is correct. r8_FIQ..r12_FIQ can store arbitrary state used by the FIQ handler, if FIQ is in use. Can we expect any driver using FIQ to save/restore this state itself, rather than doing it globally? This may be reasonable. Cheers ---Dave
On Fri, May 20, 2011 at 12:37:58PM +0100, Dave Martin wrote: > Where do we save/restore r8_FIQ..r13_FIQ, r13_IRQ, r13_UND and r13_ABT? > (I'm assuming there's no reason to save/restore r14 or SPSR for any > exception mode, since we presumably aren't going to suspend/resume > from inside an exception handler (?)) There is absolutely no need to save r13 for _any_ of the abort modes. As we have to set them up at boot time to fixed values, we keep that code around, and in the resume paths we re-execute that initialization code. cpu_init(). Out of the list you mention above, the only thing which isn't saved are the FIQ registers, and that's a problem for S2RAM too, and should be done by arch/arm/kernel/fiq.c hooking into the suspend paths.
On Fri, May 20, 2011 at 07:05:10PM +0100, Russell King - ARM Linux wrote: > On Fri, May 20, 2011 at 12:37:58PM +0100, Dave Martin wrote: > > Where do we save/restore r8_FIQ..r13_FIQ, r13_IRQ, r13_UND and r13_ABT? > > (I'm assuming there's no reason to save/restore r14 or SPSR for any > > exception mode, since we presumably aren't going to suspend/resume > > from inside an exception handler (?)) > > There is absolutely no need to save r13 for _any_ of the abort modes. As > we have to set them up at boot time to fixed values, we keep that code > around, and in the resume paths we re-execute that initialization code. > cpu_init(). That seemed a sensible possibility, but I'm still not familiar with some of the details. It was, as I suspected, a dumb question from me... > Out of the list you mention above, the only thing which isn't saved are the > FIQ registers, and that's a problem for S2RAM too, and should be done by > arch/arm/kernel/fiq.c hooking into the suspend paths. The alternative view is that the driver using FIQ owns the state in the FIQ mode registers and is therefore responsible for saving and restoring it across suspend/resume. If so, then any additional globally implemented state save/restore of the FIQ mode state is unnecessary. Do you have an opinion on which is the better model? Requiring the driver to take responsibility might encourage the driver writers to think about all the implications of save/restore on their driver: saving/restoring the FIQ mode registers is unlikely to be enough by itself. Depending on the state of the driver, it might also be unnecessary (though it's only a few words of state, so not necessarily worth optimising). Cheers ---Dave
On Mon, May 23, 2011 at 11:01:32AM +0100, Dave Martin wrote: > On Fri, May 20, 2011 at 07:05:10PM +0100, Russell King - ARM Linux wrote: > > Out of the list you mention above, the only thing which isn't saved are the > > FIQ registers, and that's a problem for S2RAM too, and should be done by > > arch/arm/kernel/fiq.c hooking into the suspend paths. > > The alternative view is that the driver using FIQ owns the state in the FIQ > mode registers and is therefore responsible for saving and restoring it > across suspend/resume. If so, then any additional globally implemented > state save/restore of the FIQ mode state is unnecessary. This seems to be most sensible - if the FIQ is being used as a software-DMA, then the hardware side of that needs to be cleanly shutdown (eg, waiting for the DMA to complete before proceeding) to ensure no loss of data. That can't happen from within the FIQ code. I also wonder about issues of secure/non-secure stuff here too - what that means is that if we have a driver using FIQ mode, then we have FIQ state to save, but if not there's probably no point (or even any way) to save that state ourselves anyway.
On Mon, May 23, 2011 at 11:12:20AM +0100, Russell King - ARM Linux wrote: > On Mon, May 23, 2011 at 11:01:32AM +0100, Dave Martin wrote: > > On Fri, May 20, 2011 at 07:05:10PM +0100, Russell King - ARM Linux wrote: > > > Out of the list you mention above, the only thing which isn't saved are the > > > FIQ registers, and that's a problem for S2RAM too, and should be done by > > > arch/arm/kernel/fiq.c hooking into the suspend paths. > > > > The alternative view is that the driver using FIQ owns the state in the FIQ > > mode registers and is therefore responsible for saving and restoring it > > across suspend/resume. If so, then any additional globally implemented > > state save/restore of the FIQ mode state is unnecessary. > > This seems to be most sensible - if the FIQ is being used as a software-DMA, > then the hardware side of that needs to be cleanly shutdown (eg, waiting for > the DMA to complete before proceeding) to ensure no loss of data. That > can't happen from within the FIQ code. OK. Frank suggested putting comments to this effect in <asm/fiq.h>. I think something along these lines might be appropriate: /* * The FIQ mode registers are not magically preserved across suspend/resume. * * Drivers which require these registers to be preserved across power * management operations must implement appropriate suspend/resume handlers * to save and restore them. */ Is the header file a good place for this, or is there some other better place to put it? > I also wonder about issues of secure/non-secure stuff here too - what > that means is that if we have a driver using FIQ mode, then we have > FIQ state to save, but if not there's probably no point (or even any > way) to save that state ourselves anyway. That argument may apply to a ton of state in the Secure World, not just the FIQ registers The likely model there is that the Secure World must hook somewhere into Linux suspend/resume too, so that its hooks can be called at the appropriate times. This could involve a driver which saves/restores the state of the Secure World, or low-level hooks which get called from the platform power management code. Either way, Linux doesn't need to be doing anything special except for calling those hooks, just as for any other driver. Cheers ---Dave
On Mon, May 23, 2011 at 12:16:31PM +0100, Dave Martin wrote: > On Mon, May 23, 2011 at 11:12:20AM +0100, Russell King - ARM Linux wrote: > > On Mon, May 23, 2011 at 11:01:32AM +0100, Dave Martin wrote: > > > On Fri, May 20, 2011 at 07:05:10PM +0100, Russell King - ARM Linux wrote: > > > > Out of the list you mention above, the only thing which isn't saved are the > > > > FIQ registers, and that's a problem for S2RAM too, and should be done by > > > > arch/arm/kernel/fiq.c hooking into the suspend paths. > > > > > > The alternative view is that the driver using FIQ owns the state in the FIQ > > > mode registers and is therefore responsible for saving and restoring it > > > across suspend/resume. If so, then any additional globally implemented > > > state save/restore of the FIQ mode state is unnecessary. > > > > This seems to be most sensible - if the FIQ is being used as a software-DMA, > > then the hardware side of that needs to be cleanly shutdown (eg, waiting for > > the DMA to complete before proceeding) to ensure no loss of data. That > > can't happen from within the FIQ code. > > OK. Frank suggested putting comments to this effect in <asm/fiq.h>. > > I think something along these lines might be appropriate: > > /* > * The FIQ mode registers are not magically preserved across suspend/resume. > * > * Drivers which require these registers to be preserved across power > * management operations must implement appropriate suspend/resume handlers > * to save and restore them. > */ > > Is the header file a good place for this, or is there some other better > place to put it? I tend to suggest that the header file is the right place, because that's where the interface is defined. Other people argue that its more likely to be seen in the implementation (fiq.c). So I'm tempted to say both, but lets go with fiq.h for the time being. > That argument may apply to a ton of state in the Secure World, not just > the FIQ registers It very much does, and I know OMAP has some kind of SMC call to handle this.
On Mon, May 23, 2011 at 05:11:49PM +0100, Russell King - ARM Linux wrote: > On Mon, May 23, 2011 at 12:16:31PM +0100, Dave Martin wrote: > > On Mon, May 23, 2011 at 11:12:20AM +0100, Russell King - ARM Linux wrote: > > > On Mon, May 23, 2011 at 11:01:32AM +0100, Dave Martin wrote: > > > > On Fri, May 20, 2011 at 07:05:10PM +0100, Russell King - ARM Linux wrote: > > > > > Out of the list you mention above, the only thing which isn't saved are the > > > > > FIQ registers, and that's a problem for S2RAM too, and should be done by > > > > > arch/arm/kernel/fiq.c hooking into the suspend paths. > > > > > > > > The alternative view is that the driver using FIQ owns the state in the FIQ > > > > mode registers and is therefore responsible for saving and restoring it > > > > across suspend/resume. If so, then any additional globally implemented > > > > state save/restore of the FIQ mode state is unnecessary. > > > > > > This seems to be most sensible - if the FIQ is being used as a software-DMA, > > > then the hardware side of that needs to be cleanly shutdown (eg, waiting for > > > the DMA to complete before proceeding) to ensure no loss of data. That > > > can't happen from within the FIQ code. > > > > OK. Frank suggested putting comments to this effect in <asm/fiq.h>. > > > > I think something along these lines might be appropriate: > > > > /* > > * The FIQ mode registers are not magically preserved across suspend/resume. > > * > > * Drivers which require these registers to be preserved across power > > * management operations must implement appropriate suspend/resume handlers > > * to save and restore them. > > */ > > > > Is the header file a good place for this, or is there some other better > > place to put it? > > I tend to suggest that the header file is the right place, because that's > where the interface is defined. Other people argue that its more likely > to be seen in the implementation (fiq.c). So I'm tempted to say both, > but lets go with fiq.h for the time being. OK -- the {get,set}_fiq_regs patch is currently in your patch system. If you have no objection, I'll submit a patch adding the above text to apply on top of the other patch (or, if possible, orthogonally). ---Dave > > > That argument may apply to a ton of state in the Secure World, not just > > the FIQ registers > > It very much does, and I know OMAP has some kind of SMC call to handle > this.
On Mon, 23 May 2011, Dave Martin wrote: > On Mon, May 23, 2011 at 05:11:49PM +0100, Russell King - ARM Linux wrote: [ ... ] >> I tend to suggest that the header file is the right place, because that's >> where the interface is defined. Other people argue that its more likely >> to be seen in the implementation (fiq.c). So I'm tempted to say both, >> but lets go with fiq.h for the time being. > > OK -- the {get,set}_fiq_regs patch is currently in your patch system. > > If you have no objection, I'll submit a patch adding the above text to apply > on top of the other patch (or, if possible, orthogonally). > > ---Dave Thanks a lot ! > >> >>> That argument may apply to a ton of state in the Secure World, not just >>> the FIQ registers >> >> It very much does, and I know OMAP has some kind of SMC call to handle >> this. > Yes, _omap_sram_idle() does that bit, it gives a physical address to the OMAP ROM code to save/restore the "secure state" in, triggered via smc. Anyway, architecturally it seems to be much cleaner to _allow_ device drivers (or machine-specific hooks) to save/restore _more_ state than whatever the "core suspend code" would do, instead of _forcing_ the core suspend code to do everything-and-the-kitchen-sink. That's where things like FIQ or secure state would be. FrankH.
arch/arm/Kconfig | 3 + arch/arm/include/asm/memory.h | 1 + arch/arm/include/asm/suspend.h | 6 ++ arch/arm/kernel/cpu.c | 65 ++++++++++++++++++++++++++ arch/arm/kernel/swsusp.S | 92 +++++++++++++++++++++++++++++++++++++ arch/arm/kernel/vmlinux.lds.S | 3 +- include/asm-generic/vmlinux.lds.h | 2 +- 7 files changed, 170 insertions(+), 2 deletions(-) diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 6b6786c..859dd86 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -198,6 +198,9 @@ config VECTORS_BASE config ARCH_HAS_CPU_IDLE_WAIT def_bool y +config ARCH_HIBERNATION_POSSIBLE + def_bool n + source "init/Kconfig" source "kernel/Kconfig.freezer" diff --git a/arch/arm/include/asm/memory.h b/arch/arm/include/asm/memory.h index 5421d82..23e93a6 100644 --- a/arch/arm/include/asm/memory.h +++ b/arch/arm/include/asm/memory.h @@ -191,6 +191,7 @@ static inline void *phys_to_virt(unsigned long x) */ #define __pa(x) __virt_to_phys((unsigned long)(x)) #define __va(x) ((void *)__phys_to_virt((unsigned long)(x))) +#define __pa_symbol(x) __pa(RELOC_HIDE((unsigned long)(x),0)) #define pfn_to_kaddr(pfn) __va((pfn) << PAGE_SHIFT) /* diff --git a/arch/arm/include/asm/suspend.h b/arch/arm/include/asm/suspend.h new file mode 100644 index 0000000..7ab1fd2 --- /dev/null +++ b/arch/arm/include/asm/suspend.h @@ -0,0 +1,6 @@ +#ifndef __ASM_ARM_SUSPEND_H +#define __ASM_ARM_SUSPEND_H + +static inline int arch_prepare_suspend(void) { return 0; } + +#endif /* __ASM_ARM_SUSPEND_H */ diff --git a/arch/arm/kernel/cpu.c b/arch/arm/kernel/cpu.c new file mode 100644 index 0000000..764c8fa --- /dev/null +++ b/arch/arm/kernel/cpu.c @@ -0,0 +1,65 @@ +/* + * Hibernation support specific for ARM + * + * Derived from work on ARM hibernation support by: + * + * Ubuntu project, hibernation support for mach-dove + * Copyright (C) 2010 Nokia Corporation (Hiroshi Doyu) + * Copyright (C) 2010 Texas Instruments, Inc. (Teerth Reddy et al.) + * https://lkml.org/lkml/2010/6/18/4 + * https://lists.linux-foundation.org/pipermail/linux-pm/2010-June/027422.html + * https://patchwork.kernel.org/patch/96442/ + * + * Copyright (C) 2006 Rafael J. Wysocki <rjw@sisk.pl> + * + * License terms: GNU General Public License (GPL) version 2 + */ + +#include <linux/mm.h> +#include <linux/sched.h> +#include <linux/suspend.h> +#include <asm/tlbflush.h> + +extern const void __nosave_begin, __nosave_end; + +int pfn_is_nosave(unsigned long pfn) +{ + unsigned long nosave_begin_pfn = __pa_symbol(&__nosave_begin) >> PAGE_SHIFT; + unsigned long nosave_end_pfn = PAGE_ALIGN(__pa_symbol(&__nosave_end)) >> PAGE_SHIFT; + + return (pfn >= nosave_begin_pfn) && (pfn < nosave_end_pfn); +} + +void save_processor_state(void) +{ + flush_thread(); +} + +void restore_processor_state(void) +{ + local_flush_tlb_all(); +} + +u8 __swsusp_arch_ctx[PAGE_SIZE] __attribute__((aligned(PAGE_SIZE))); +u8 __swsusp_resume_stk[PAGE_SIZE/2] __nosavedata; + +/* + * The framework loads the hibernation image into this linked list, + * for swsusp_arch_resume() to copy back to the proper destinations. + * + * To make this work if resume is triggered from initramfs, the + * pagetables need to be switched to allow writes to kernel mem. + */ +void notrace __swsusp_arch_restore_prepare(void) +{ + cpu_switch_mm(__virt_to_phys(swapper_pg_dir), current->active_mm); +} + +void notrace __swsusp_arch_restore_image(void) +{ + extern struct pbe *restore_pblist; + struct pbe *pbe; + + for (pbe = restore_pblist; pbe; pbe = pbe->next) + copy_page(pbe->orig_address, pbe->address); +} diff --git a/arch/arm/kernel/swsusp.S b/arch/arm/kernel/swsusp.S new file mode 100644 index 0000000..fb260a7 --- /dev/null +++ b/arch/arm/kernel/swsusp.S @@ -0,0 +1,92 @@ +/* + * Hibernation support specific for ARM + * + * Based on work by: + * + * Ubuntu project, hibernation support for mach-dove, + * Copyright (C) 2010 Nokia Corporation (Hiroshi Doyu) + * Copyright (C) 2010 Texas Instruments, Inc. (Teerth Reddy et al.) + * https://lkml.org/lkml/2010/6/18/4 + * https://lists.linux-foundation.org/pipermail/linux-pm/2010-June/027422.html + * https://patchwork.kernel.org/patch/96442/ + * + * Copyright (C) 2006 Rafael J. Wysocki <rjw@sisk.pl> + * + * License terms: GNU General Public License (GPL) version 2 + */ + +#include <linux/linkage.h> +#include <asm/memory.h> +#include <asm/page.h> +#include <asm/cache.h> +#include <asm/ptrace.h> + +/* + * Save the current CPU state before suspend / poweroff. + */ +ENTRY(swsusp_arch_suspend) + ldr r0, =__swsusp_arch_ctx + mrs r1, cpsr + str r1, [r0], #4 /* CPSR */ +ARM( msr cpsr_c, #SYSTEM_MODE ) +THUMB( mov r2, #SYSTEM_MODE ) +THUMB( msr cpsr_c, r2 ) + stm r0!, {r4-r12,lr} /* nonvolatile regs */ + str sp, [r0], #4 +ARM( msr cpsr_c, #SVC_MODE ) +THUMB( mov r2, #SVC_MODE ) +THUMB( msr cpsr_c, r2 ) + mrs r2, spsr + stm r0!, {r2,lr} /* SVC SPSR, SVC regs */ + str sp, [r0], #4 + msr cpsr, r1 /* restore mode at entry */ + push {lr} + bl __save_processor_state + pop {lr} + b swsusp_save +ENDPROC(swsusp_arch_suspend) + +/* + * Restore the memory image from the pagelists, and load the CPU registers + * from saved state. + */ +ENTRY(swsusp_arch_resume) + bl __swsusp_arch_restore_prepare + /* + * Switch stack to a nosavedata region to make sure image restore + * doesn't clobber it underneath itself. + */ + ldr sp, =(__swsusp_resume_stk + PAGE_SIZE / 2) + bl __swsusp_arch_restore_image + + /* + * Restore the CPU registers. + */ +ARM( msr cpsr_c, #SYSTEM_MODE ) +THUMB( mov r2, #SYSTEM_MODE ) +THUMB( msr cpsr_c, r2 ) + ldr r0, =__swsusp_arch_ctx + ldr r1, [r0], #4 + msr cpsr_cxsf, r1 + ldm r0!, {r4-r12,lr} + ldr sp, [r0], #4 +ARM( msr cpsr_c, #SVC_MODE ) +THUMB( mov r2, #SVC_MODE ) +THUMB( msr cpsr_c, r2 ) + ldm r0!, {r2,lr} + ldr sp, [r0], #4 + msr spsr_cxsf, r2 + msr cpsr_c, r1 + + /* + * From here on we have a valid stack again. Core state is + * not restored yet, redirect to the machine-specific + * implementation to get that done. + * Resume has succeeded at this point; if the machine-specific + * code wants to fail it needs to panic. + */ + mov r1, #0 + push {r1,lr} + bl __restore_processor_state /* restore core state */ + pop {r0,pc} +ENDPROC(swsusp_arch_resume) diff --git a/arch/arm/kernel/vmlinux.lds.S b/arch/arm/kernel/vmlinux.lds.S index 4957e13..e691c77 100644 --- a/arch/arm/kernel/vmlinux.lds.S +++ b/arch/arm/kernel/vmlinux.lds.S @@ -153,7 +153,6 @@ SECTIONS __init_end = .; #endif - NOSAVE_DATA CACHELINE_ALIGNED_DATA(32) /* @@ -176,6 +175,8 @@ SECTIONS } _edata_loc = __data_loc + SIZEOF(.data); + NOSAVE_DATA + #ifdef CONFIG_HAVE_TCM /* * We align everything to a page boundary so we can diff --git a/include/asm-generic/vmlinux.lds.h b/include/asm-generic/vmlinux.lds.h index b6e818f..0d39ae0 100644 --- a/include/asm-generic/vmlinux.lds.h +++ b/include/asm-generic/vmlinux.lds.h @@ -171,7 +171,7 @@ #define NOSAVE_DATA \ . = ALIGN(PAGE_SIZE); \ VMLINUX_SYMBOL(__nosave_begin) = .; \ - *(.data.nosave) \ + .data.nosave : { *(.data.nosave) } \ . = ALIGN(PAGE_SIZE); \ VMLINUX_SYMBOL(__nosave_end) = .;