Message ID | 1559330150-30099-2-git-send-email-hancock@sedsystems.ca |
---|---|
State | Not Applicable |
Delegated to: | David Miller |
Headers | show |
Series | [net-next] net: phy: Ensure scheduled work is cancelled during removal | expand |
Robert Please make sure you Cc: PHY patches to the PHY maintainers. Heiner, this one is for you. Andrew On Fri, May 31, 2019 at 01:15:50PM -0600, Robert Hancock wrote: > It is possible that scheduled work started by the PHY driver is still > outstanding when phy_device_remove is called if the PHY was initially > started but never connected, and therefore phy_disconnect is never > called. phy_stop does not guarantee that the scheduled work is stopped > because it is called under rtnl_lock. This can cause an oops due to > use-after-free if the delayed work fires after freeing the PHY device. > > Ensure that the state_queue work is cancelled in both phy_device_remove > and phy_remove paths. > > Signed-off-by: Robert Hancock <hancock@sedsystems.ca> > --- > drivers/net/phy/phy_device.c | 2 ++ > 1 file changed, 2 insertions(+) > > diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c > index 2c879ba..1c90b33 100644 > --- a/drivers/net/phy/phy_device.c > +++ b/drivers/net/phy/phy_device.c > @@ -877,6 +877,8 @@ int phy_device_register(struct phy_device *phydev) > */ > void phy_device_remove(struct phy_device *phydev) > { > + cancel_delayed_work_sync(&phydev->state_queue); > + > device_del(&phydev->mdio.dev); > > /* Assert the reset signal */ > -- > 1.8.3.1 >
On 31.05.2019 22:54, Andrew Lunn wrote: > Robert > > Please make sure you Cc: PHY patches to the PHY maintainers. > > Heiner, this one is for you. > > Andrew > > On Fri, May 31, 2019 at 01:15:50PM -0600, Robert Hancock wrote: >> It is possible that scheduled work started by the PHY driver is still >> outstanding when phy_device_remove is called if the PHY was initially >> started but never connected, and therefore phy_disconnect is never >> called. phy_stop does not guarantee that the scheduled work is stopped >> because it is called under rtnl_lock. This can cause an oops due to >> use-after-free if the delayed work fires after freeing the PHY device. >> The patch itself at least shouldn't do any harm. However the justification isn't fully convincing yet. PHY drivers don't start any scheduled work. This queue is used by the phylib state machine. phy_stop usually isn't called under rtnl_lock, and it calls phy_stop_machine that cancels pending work. Did you experience such an oops? Can you provide a call chain where your described scenario could happen? >> Ensure that the state_queue work is cancelled in both phy_device_remove >> and phy_remove paths. >> >> Signed-off-by: Robert Hancock <hancock@sedsystems.ca> >> --- >> drivers/net/phy/phy_device.c | 2 ++ >> 1 file changed, 2 insertions(+) >> >> diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c >> index 2c879ba..1c90b33 100644 >> --- a/drivers/net/phy/phy_device.c >> +++ b/drivers/net/phy/phy_device.c >> @@ -877,6 +877,8 @@ int phy_device_register(struct phy_device *phydev) >> */ >> void phy_device_remove(struct phy_device *phydev) >> { >> + cancel_delayed_work_sync(&phydev->state_queue); >> + >> device_del(&phydev->mdio.dev); >> >> /* Assert the reset signal */ >> -- >> 1.8.3.1 >> >
> On 31.05.2019 22:54, Andrew Lunn wrote: >>> It is possible that scheduled work started by the PHY driver is still >>> outstanding when phy_device_remove is called if the PHY was initially >>> started but never connected, and therefore phy_disconnect is never >>> called. phy_stop does not guarantee that the scheduled work is stopped >>> because it is called under rtnl_lock. This can cause an oops due to >>> use-after-free if the delayed work fires after freeing the PHY device. >>> > The patch itself at least shouldn't do any harm. However the justification > isn't fully convincing yet. > PHY drivers don't start any scheduled work. This queue is used by the > phylib state machine. phy_stop usually isn't called under rtnl_lock, > and it calls phy_stop_machine that cancels pending work. > Did you experience such an oops? Can you provide a call chain where > your described scenario could happen? Upon further investigation, it appears that this change is no longer needed in the mainline. Previously (such as in 4.19 kernels as we are using), phy_stop did not call phy_stop_machine, only phy_disconnect did, so if the phy was started but never connected and disconnected before stopping it, the delayed work was not stopped. That sequence didn't occur often, but could happen in some failure cases which I believe was what I ran into during development when this change was originally made. It looks like this was fixed in commit cbfd12b3e8c3542e8142aa041714ed614d3f67b0 "net: phy: ensure phylib state machine is stopped after calling phy_stop". So my patch can be dropped - but maybe that patch should be added to stable?
On Fri, May 31, 2019 at 09:22:16PM -0600, hancock@sedsystems.ca wrote: > > On 31.05.2019 22:54, Andrew Lunn wrote: > >>> It is possible that scheduled work started by the PHY driver is still > >>> outstanding when phy_device_remove is called if the PHY was initially > >>> started but never connected, and therefore phy_disconnect is never > >>> called. phy_stop does not guarantee that the scheduled work is stopped > >>> because it is called under rtnl_lock. This can cause an oops due to > >>> use-after-free if the delayed work fires after freeing the PHY device. > >>> > > The patch itself at least shouldn't do any harm. However the justification > > isn't fully convincing yet. > > PHY drivers don't start any scheduled work. This queue is used by the > > phylib state machine. phy_stop usually isn't called under rtnl_lock, > > and it calls phy_stop_machine that cancels pending work. > > Did you experience such an oops? Can you provide a call chain where > > your described scenario could happen? > > Upon further investigation, it appears that this change is no longer > needed in the mainline. Previously (such as in 4.19 kernels as we are > using), Hi Robert Please do all your testing on net-next. 4.19 is dead, in terms of development. There is no point in developing and testing on it patches intended for mainline. Andrew
diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c index 2c879ba..1c90b33 100644 --- a/drivers/net/phy/phy_device.c +++ b/drivers/net/phy/phy_device.c @@ -877,6 +877,8 @@ int phy_device_register(struct phy_device *phydev) */ void phy_device_remove(struct phy_device *phydev) { + cancel_delayed_work_sync(&phydev->state_queue); + device_del(&phydev->mdio.dev); /* Assert the reset signal */
It is possible that scheduled work started by the PHY driver is still outstanding when phy_device_remove is called if the PHY was initially started but never connected, and therefore phy_disconnect is never called. phy_stop does not guarantee that the scheduled work is stopped because it is called under rtnl_lock. This can cause an oops due to use-after-free if the delayed work fires after freeing the PHY device. Ensure that the state_queue work is cancelled in both phy_device_remove and phy_remove paths. Signed-off-by: Robert Hancock <hancock@sedsystems.ca> --- drivers/net/phy/phy_device.c | 2 ++ 1 file changed, 2 insertions(+)