Message ID | 20190312145554.25488-1-hdegoede@redhat.com |
---|---|
State | Accepted |
Headers | show |
Series | [v2,1/2] i2c: i2c-designware-platdrv: Cleanup setting of the adapter number | expand |
On Tue, Mar 12, 2019 at 03:55:53PM +0100, Hans de Goede wrote: > i2c-designware-platdrv assumes that if the pdev has an apci-companion > it should use a dynamic adapter-nr and otherwise it will use pdev->id > as adapter-nr. > > Before this commit the setting of the adapter.nr was somewhat convoluted, > in the acpi_companion case it was set from dw_i2c_acpi_configure, in the > non acpi_companion case it was set from dw_i2c_set_fifo_size based on > tx_fifo_depth not being set yet indicating that dw_i2c_acpi_configure was > not executed. > > This cleans this up, directly setting the adapter-nr from > dw_i2c_plat_probe for both cases. > As has been discussed earlier, this is good one Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> > Signed-off-by: Hans de Goede <hdegoede@redhat.com> > --- > Changes in v2: > -Split out the code cleaning up the adapter.nr setting into a separate patch > --- > drivers/i2c/busses/i2c-designware-platdrv.c | 10 ++++++---- > 1 file changed, 6 insertions(+), 4 deletions(-) > > diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c > index ead5e7de3e4d..30529839cbd2 100644 > --- a/drivers/i2c/busses/i2c-designware-platdrv.c > +++ b/drivers/i2c/busses/i2c-designware-platdrv.c > @@ -86,7 +86,6 @@ static int dw_i2c_acpi_configure(struct platform_device *pdev) > struct i2c_timings *t = &dev->timings; > u32 ss_ht = 0, fp_ht = 0, hs_ht = 0, fs_ht = 0; > > - dev->adapter.nr = -1; > dev->tx_fifo_depth = 32; > dev->rx_fifo_depth = 32; > > @@ -219,7 +218,7 @@ static void i2c_dw_configure_slave(struct dw_i2c_dev *dev) > dev->mode = DW_IC_SLAVE; > } > > -static void dw_i2c_set_fifo_size(struct dw_i2c_dev *dev, int id) > +static void dw_i2c_set_fifo_size(struct dw_i2c_dev *dev) > { > u32 param, tx_fifo_depth, rx_fifo_depth; > > @@ -233,7 +232,6 @@ static void dw_i2c_set_fifo_size(struct dw_i2c_dev *dev, int id) > if (!dev->tx_fifo_depth) { > dev->tx_fifo_depth = tx_fifo_depth; > dev->rx_fifo_depth = rx_fifo_depth; > - dev->adapter.nr = id; > } else if (tx_fifo_depth >= 2) { > dev->tx_fifo_depth = min_t(u32, dev->tx_fifo_depth, > tx_fifo_depth); > @@ -358,13 +356,17 @@ static int dw_i2c_plat_probe(struct platform_device *pdev) > div_u64(clk_khz * t->sda_hold_ns + 500000, 1000000); > } > > - dw_i2c_set_fifo_size(dev, pdev->id); > + dw_i2c_set_fifo_size(dev); > > adap = &dev->adapter; > adap->owner = THIS_MODULE; > adap->class = I2C_CLASS_DEPRECATED; > ACPI_COMPANION_SET(&adap->dev, ACPI_COMPANION(&pdev->dev)); > adap->dev.of_node = pdev->dev.of_node; > + if (has_acpi_companion(&pdev->dev)) > + adap->nr = -1; > + else > + adap->nr = pdev->id; > > dev_pm_set_driver_flags(&pdev->dev, > DPM_FLAG_SMART_PREPARE | > -- > 2.20.1 >
On Tue, Mar 12, 2019 at 05:07:23PM +0200, Andy Shevchenko wrote: > On Tue, Mar 12, 2019 at 03:55:53PM +0100, Hans de Goede wrote: > > i2c-designware-platdrv assumes that if the pdev has an apci-companion > > it should use a dynamic adapter-nr and otherwise it will use pdev->id > > as adapter-nr. > > > > Before this commit the setting of the adapter.nr was somewhat convoluted, > > in the acpi_companion case it was set from dw_i2c_acpi_configure, in the > > non acpi_companion case it was set from dw_i2c_set_fifo_size based on > > tx_fifo_depth not being set yet indicating that dw_i2c_acpi_configure was > > not executed. > > > > This cleans this up, directly setting the adapter-nr from > > dw_i2c_plat_probe for both cases. > > > > As has been discussed earlier, this is good one > > Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> The other patch, too? If so, please tag it seperately, so patchwork can pick it up. (for bigger series, tags for the cover-letter is ok for me)
On Tue, Mar 12, 2019 at 04:20:44PM +0100, Wolfram Sang wrote: > On Tue, Mar 12, 2019 at 05:07:23PM +0200, Andy Shevchenko wrote: > > On Tue, Mar 12, 2019 at 03:55:53PM +0100, Hans de Goede wrote: > > > i2c-designware-platdrv assumes that if the pdev has an apci-companion > > > it should use a dynamic adapter-nr and otherwise it will use pdev->id > > > as adapter-nr. > > > > > > Before this commit the setting of the adapter.nr was somewhat convoluted, > > > in the acpi_companion case it was set from dw_i2c_acpi_configure, in the > > > non acpi_companion case it was set from dw_i2c_set_fifo_size based on > > > tx_fifo_depth not being set yet indicating that dw_i2c_acpi_configure was > > > not executed. > > > > > > This cleans this up, directly setting the adapter-nr from > > > dw_i2c_plat_probe for both cases. > > > > > > > As has been discussed earlier, this is good one > > > > Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> > > The other patch, too? If so, please tag it seperately, so patchwork can > pick it up. (for bigger series, tags for the cover-letter is ok for me) Yes, that's the plan. I have been reviewing it now.
> Yes, that's the plan. I have been reviewing it now.
Super! Sorry for being a tad impatient.
On 3/12/19 5:07 PM, Andy Shevchenko wrote: > On Tue, Mar 12, 2019 at 03:55:53PM +0100, Hans de Goede wrote: >> i2c-designware-platdrv assumes that if the pdev has an apci-companion >> it should use a dynamic adapter-nr and otherwise it will use pdev->id >> as adapter-nr. >> >> Before this commit the setting of the adapter.nr was somewhat convoluted, >> in the acpi_companion case it was set from dw_i2c_acpi_configure, in the >> non acpi_companion case it was set from dw_i2c_set_fifo_size based on >> tx_fifo_depth not being set yet indicating that dw_i2c_acpi_configure was >> not executed. >> >> This cleans this up, directly setting the adapter-nr from >> dw_i2c_plat_probe for both cases. >> > > As has been discussed earlier, this is good one > > Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> > Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
On Tue, Mar 12, 2019 at 03:55:53PM +0100, Hans de Goede wrote: > i2c-designware-platdrv assumes that if the pdev has an apci-companion > it should use a dynamic adapter-nr and otherwise it will use pdev->id > as adapter-nr. > > Before this commit the setting of the adapter.nr was somewhat convoluted, > in the acpi_companion case it was set from dw_i2c_acpi_configure, in the > non acpi_companion case it was set from dw_i2c_set_fifo_size based on > tx_fifo_depth not being set yet indicating that dw_i2c_acpi_configure was > not executed. > > This cleans this up, directly setting the adapter-nr from > dw_i2c_plat_probe for both cases. > > Signed-off-by: Hans de Goede <hdegoede@redhat.com> Applied to for-current, thanks!
diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c index ead5e7de3e4d..30529839cbd2 100644 --- a/drivers/i2c/busses/i2c-designware-platdrv.c +++ b/drivers/i2c/busses/i2c-designware-platdrv.c @@ -86,7 +86,6 @@ static int dw_i2c_acpi_configure(struct platform_device *pdev) struct i2c_timings *t = &dev->timings; u32 ss_ht = 0, fp_ht = 0, hs_ht = 0, fs_ht = 0; - dev->adapter.nr = -1; dev->tx_fifo_depth = 32; dev->rx_fifo_depth = 32; @@ -219,7 +218,7 @@ static void i2c_dw_configure_slave(struct dw_i2c_dev *dev) dev->mode = DW_IC_SLAVE; } -static void dw_i2c_set_fifo_size(struct dw_i2c_dev *dev, int id) +static void dw_i2c_set_fifo_size(struct dw_i2c_dev *dev) { u32 param, tx_fifo_depth, rx_fifo_depth; @@ -233,7 +232,6 @@ static void dw_i2c_set_fifo_size(struct dw_i2c_dev *dev, int id) if (!dev->tx_fifo_depth) { dev->tx_fifo_depth = tx_fifo_depth; dev->rx_fifo_depth = rx_fifo_depth; - dev->adapter.nr = id; } else if (tx_fifo_depth >= 2) { dev->tx_fifo_depth = min_t(u32, dev->tx_fifo_depth, tx_fifo_depth); @@ -358,13 +356,17 @@ static int dw_i2c_plat_probe(struct platform_device *pdev) div_u64(clk_khz * t->sda_hold_ns + 500000, 1000000); } - dw_i2c_set_fifo_size(dev, pdev->id); + dw_i2c_set_fifo_size(dev); adap = &dev->adapter; adap->owner = THIS_MODULE; adap->class = I2C_CLASS_DEPRECATED; ACPI_COMPANION_SET(&adap->dev, ACPI_COMPANION(&pdev->dev)); adap->dev.of_node = pdev->dev.of_node; + if (has_acpi_companion(&pdev->dev)) + adap->nr = -1; + else + adap->nr = pdev->id; dev_pm_set_driver_flags(&pdev->dev, DPM_FLAG_SMART_PREPARE |
i2c-designware-platdrv assumes that if the pdev has an apci-companion it should use a dynamic adapter-nr and otherwise it will use pdev->id as adapter-nr. Before this commit the setting of the adapter.nr was somewhat convoluted, in the acpi_companion case it was set from dw_i2c_acpi_configure, in the non acpi_companion case it was set from dw_i2c_set_fifo_size based on tx_fifo_depth not being set yet indicating that dw_i2c_acpi_configure was not executed. This cleans this up, directly setting the adapter-nr from dw_i2c_plat_probe for both cases. Signed-off-by: Hans de Goede <hdegoede@redhat.com> --- Changes in v2: -Split out the code cleaning up the adapter.nr setting into a separate patch --- drivers/i2c/busses/i2c-designware-platdrv.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-)