Message ID | 20190131161515.21605-1-tudor.ambarus@microchip.com |
---|---|
Headers | show |
Series | spi: atmel-quadspi: introduce sam9x60 qspi controller | expand |
On Thu, 31 Jan 2019 16:15:51 +0000 <Tudor.Ambarus@microchip.com> wrote: > From: Tudor Ambarus <tudor.ambarus@microchip.com> > > The sam9x60 qspi controller uses 2 clocks, one for the peripheral register > access, the other for the qspi core and phy. Both are mandatory. It uses > dedicated register for Read Instruction Code Register (RICR) and > Write Instruction Code Register (WICR). ICR/RICR/WICR have identical > fields. > > Tested with sst26vf064b jedec,spi-nor flash. Backward compatibility test > done on sama5d2 qspi controller and mx25l25635e jedec,spi-nor flash. > > Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> > --- > v2: > - rework clock handling > - reorder setting of register values in set_cfg() calls -> move functions > that can fail in the upper part of the function body. > > drivers/spi/atmel-quadspi.c | 296 +++++++++++++++++++++++++++++++++++--------- > 1 file changed, 239 insertions(+), 57 deletions(-) > > diff --git a/drivers/spi/atmel-quadspi.c b/drivers/spi/atmel-quadspi.c > index d3e76acf8517..80c934f3e479 100644 > --- a/drivers/spi/atmel-quadspi.c > +++ b/drivers/spi/atmel-quadspi.c > @@ -19,6 +19,7 @@ > #include <linux/kernel.h> > #include <linux/module.h> > #include <linux/of.h> > +#include <linux/of_platform.h> > #include <linux/platform_device.h> > #include <linux/spi/spi-mem.h> > > @@ -35,7 +36,9 @@ > > #define QSPI_IAR 0x0030 /* Instruction Address Register */ > #define QSPI_ICR 0x0034 /* Instruction Code Register */ > +#define QSPI_WICR 0x0034 /* Write Instruction Code Register */ > #define QSPI_IFR 0x0038 /* Instruction Frame Register */ > +#define QSPI_RICR 0x003C /* Read Instruction Code Register */ > > #define QSPI_SMR 0x0040 /* Scrambling Mode Register */ > #define QSPI_SKR 0x0044 /* Scrambling Key Register */ > @@ -88,7 +91,7 @@ > #define QSPI_SCR_DLYBS_MASK GENMASK(23, 16) > #define QSPI_SCR_DLYBS(n) (((n) << 16) & QSPI_SCR_DLYBS_MASK) > > -/* Bitfields in QSPI_ICR (Instruction Code Register) */ > +/* Bitfields in QSPI_ICR (Read/Write Instruction Code Register) */ > #define QSPI_ICR_INST_MASK GENMASK(7, 0) > #define QSPI_ICR_INST(inst) (((inst) << 0) & QSPI_ICR_INST_MASK) > #define QSPI_ICR_OPT_MASK GENMASK(23, 16) > @@ -113,6 +116,8 @@ > #define QSPI_IFR_OPTL_4BIT (2 << 8) > #define QSPI_IFR_OPTL_8BIT (3 << 8) > #define QSPI_IFR_ADDRL BIT(10) > +#define QSPI_IFR_TFRTYP_TRSFR_MEM BIT(12) > +#define QSPI_IFR_TFRTYP_TRSFR_REG (0 << 12) You don't need to define TRSFR_REG, just set QSPI_IFR_TFRTYP_TRSFR_MEM when you do a mem transfer and do nothing when this is a regular transfer. > #define QSPI_IFR_TFRTYP_MASK GENMASK(13, 12) > #define QSPI_IFR_TFRTYP_TRSFR_READ (0 << 12) > #define QSPI_IFR_TFRTYP_TRSFR_READ_MEM (1 << 12) Looks like the read/write flag is on bit 13. Can we just add #define QSPI_IFR_TFRTYP_TRSFR_WRITE BIT(13) and drop all others def? This way the implementation is consistent between sam9x60 and sama5d2. > @@ -121,6 +126,8 @@ > #define QSPI_IFR_CRM BIT(14) > #define QSPI_IFR_NBDUM_MASK GENMASK(20, 16) > #define QSPI_IFR_NBDUM(n) (((n) << 16) & QSPI_IFR_NBDUM_MASK) > +#define QSPI_IFR_APBTFRTYP_WRITE (0 << 24) As for the other defs, I don't think you need to define _WRITE. > +#define QSPI_IFR_APBTFRTYP_READ BIT(24) > > /* Bitfields in QSPI_SMR (Scrambling Mode Register) */ > #define QSPI_SMR_SCREN BIT(0) > @@ -137,16 +144,37 @@ > #define QSPI_WPSR_WPVSRC(src) (((src) << 8) & QSPI_WPSR_WPVSRC) > > > +/* Describes register values. */ > +struct atmel_qspi_cfg { > + u32 icr; > + u32 iar; > + u32 ifr; > +}; > + > +struct atmel_qspi_caps; > + > struct atmel_qspi { > void __iomem *regs; > void __iomem *mem; > struct clk *clk; Can we rename that on pclk? > + struct clk *qspick; > struct platform_device *pdev; > + const struct atmel_qspi_caps *caps; > u32 pending; > u32 mr; > struct completion cmd_completion; > }; > ... > + > +static int atmel_sam9x60_qspi_set_cfg(void __iomem *base, > + const struct spi_mem_op *op, > + struct atmel_qspi_cfg *cfg) > +{ > + int ret = atmel_qspi_set_mode(cfg, op); > + > + if (ret) > + return ret; > + > + ret = atmel_qspi_set_address_mode(cfg, op); > + if (ret) > + return ret; > + > + cfg->ifr |= QSPI_IFR_INSTEN; > + cfg->icr |= QSPI_ICR_INST(op->cmd.opcode); > + > + /* Set data enable */ > + if (op->data.nbytes) > + cfg->ifr |= QSPI_IFR_DATAEN; > + > + if (!op->addr.nbytes) { > + cfg->ifr |= QSPI_IFR_TFRTYP_TRSFR_REG; > + if (op->data.dir == SPI_MEM_DATA_OUT) > + cfg->ifr |= QSPI_IFR_APBTFRTYP_WRITE; > + else > + cfg->ifr |= QSPI_IFR_APBTFRTYP_READ; > + } else { > + cfg->ifr |= QSPI_IFR_TFRTYP_TRSFR_MEM; Can you try doing only regular transfers and let me know if it still works. Support for mem transfers can then be added along with dirmap support. > + } > > /* Clear pending interrupts */ > (void)readl_relaxed(base + QSPI_SR); > > /* Set QSPI Instruction Frame registers */ > - writel_relaxed(iar, base + QSPI_IAR); > - writel_relaxed(icr, base + QSPI_ICR); > - writel_relaxed(ifr, base + QSPI_IFR); > + writel_relaxed(cfg->iar, base + QSPI_IAR); > + if (op->data.dir == SPI_MEM_DATA_OUT) > + writel_relaxed(cfg->icr, base + QSPI_ICR); > + else > + writel_relaxed(cfg->icr, base + QSPI_RICR); > + writel_relaxed(cfg->ifr, base + QSPI_IFR); > + > + return 0; > +} > + ... > @@ -443,32 +578,52 @@ static int atmel_qspi_probe(struct platform_device *pdev) > /* Enable the peripheral clock */ > err = clk_prepare_enable(aq->clk); > if (err) { > - dev_err(&pdev->dev, "failed to enable the peripheral clock\n"); > + dev_err(dev, "failed to enable the peripheral clock\n"); > goto exit; > } > > + if (caps->has_qspick) { > + /* Get the QSPI system clock */ > + aq->qspick = devm_clk_get(dev, "qspick"); > + if (IS_ERR(aq->qspick)) { > + dev_err(dev, "missing system clock\n"); > + err = PTR_ERR(aq->qspick); > + goto disable_clk; > + } > + > + /* Enable the QSPI system clock */ > + err = clk_prepare_enable(aq->qspick); > + if (err) { > + dev_err(dev, > + "failed to enable the QSPI system clock\n"); > + goto disable_clk; > + } > + } > + > /* Request the IRQ */ > irq = platform_get_irq(pdev, 0); > if (irq < 0) { > - dev_err(&pdev->dev, "missing IRQ\n"); > + dev_err(dev, "missing IRQ\n"); > err = irq; > - goto disable_clk; > + goto disable_qspick; > } > - err = devm_request_irq(&pdev->dev, irq, atmel_qspi_interrupt, > - 0, dev_name(&pdev->dev), aq); > + err = devm_request_irq(dev, irq, atmel_qspi_interrupt, 0, > + dev_name(dev), aq); > if (err) > - goto disable_clk; > + goto disable_qspick; > > err = atmel_qspi_init(aq); > if (err) > - goto disable_clk; > + goto disable_qspick; > > err = spi_register_controller(ctrl); > if (err) > - goto disable_clk; > + goto disable_qspick; > > return 0; > > +disable_qspick: > + clk_disable_unprepare(aq->qspick); > disable_clk: We should probably rename this label disable_pclk. > clk_disable_unprepare(aq->clk); > exit:
On Thu, 31 Jan 2019 16:15:28 +0000 <Tudor.Ambarus@microchip.com> wrote: > From: Tudor Ambarus <tudor.ambarus@microchip.com> > > Cache MR value to avoid write access when setting the controller > in Serial Memory Mode (SMM). SMM is set in exec_op() and not at > probe time, to let room for future regular SPI support. > > Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> > --- > v2: cache MR value instead of moving the write access at probe > > drivers/spi/atmel-quadspi.c | 5 ++++- > 1 file changed, 4 insertions(+), 1 deletion(-) > > diff --git a/drivers/spi/atmel-quadspi.c b/drivers/spi/atmel-quadspi.c > index ddc712410812..fe05aee5d845 100644 > --- a/drivers/spi/atmel-quadspi.c > +++ b/drivers/spi/atmel-quadspi.c > @@ -155,6 +155,7 @@ struct atmel_qspi { > struct clk *clk; > struct platform_device *pdev; > u32 pending; > + u32 mr; > struct completion cmd_completion; > }; > > @@ -238,7 +239,9 @@ static int atmel_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op) > icr = QSPI_ICR_INST(op->cmd.opcode); > ifr = QSPI_IFR_INSTEN; > > - qspi_writel(aq, QSPI_MR, QSPI_MR_SMM); > + /* Set the QSPI controller in Serial Memory Mode */ > + if (!(aq->mr & QSPI_MR_SMM)) if (aq->mr != QSPI_MR_SMM) > + qspi_writel(aq, QSPI_MR, QSPI_MR_SMM); You need to update ->mr here. > > mode = find_mode(op); > if (mode < 0)
On 01/31/2019 06:55 PM, Boris Brezillon wrote: > On Thu, 31 Jan 2019 16:15:28 +0000 > <Tudor.Ambarus@microchip.com> wrote: > >> From: Tudor Ambarus <tudor.ambarus@microchip.com> >> >> Cache MR value to avoid write access when setting the controller >> in Serial Memory Mode (SMM). SMM is set in exec_op() and not at >> probe time, to let room for future regular SPI support. >> >> Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> >> --- >> v2: cache MR value instead of moving the write access at probe >> >> drivers/spi/atmel-quadspi.c | 5 ++++- >> 1 file changed, 4 insertions(+), 1 deletion(-) >> >> diff --git a/drivers/spi/atmel-quadspi.c b/drivers/spi/atmel-quadspi.c >> index ddc712410812..fe05aee5d845 100644 >> --- a/drivers/spi/atmel-quadspi.c >> +++ b/drivers/spi/atmel-quadspi.c >> @@ -155,6 +155,7 @@ struct atmel_qspi { >> struct clk *clk; >> struct platform_device *pdev; >> u32 pending; >> + u32 mr; >> struct completion cmd_completion; >> }; >> >> @@ -238,7 +239,9 @@ static int atmel_qspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op) >> icr = QSPI_ICR_INST(op->cmd.opcode); >> ifr = QSPI_IFR_INSTEN; >> >> - qspi_writel(aq, QSPI_MR, QSPI_MR_SMM); >> + /* Set the QSPI controller in Serial Memory Mode */ >> + if (!(aq->mr & QSPI_MR_SMM)) > > if (aq->mr != QSPI_MR_SMM) then I should probably rename mr to smm. > >> + qspi_writel(aq, QSPI_MR, QSPI_MR_SMM); > > You need to update ->mr here. of course, thanks! > >> >> mode = find_mode(op); >> if (mode < 0) > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel >
On 01/31/2019 06:32 PM, Boris Brezillon wrote: > On Thu, 31 Jan 2019 16:15:51 +0000 > <Tudor.Ambarus@microchip.com> wrote: > >> From: Tudor Ambarus <tudor.ambarus@microchip.com> >> >> The sam9x60 qspi controller uses 2 clocks, one for the peripheral register >> access, the other for the qspi core and phy. Both are mandatory. It uses >> dedicated register for Read Instruction Code Register (RICR) and >> Write Instruction Code Register (WICR). ICR/RICR/WICR have identical >> fields. >> >> Tested with sst26vf064b jedec,spi-nor flash. Backward compatibility test >> done on sama5d2 qspi controller and mx25l25635e jedec,spi-nor flash. >> >> Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> >> --- >> v2: >> - rework clock handling >> - reorder setting of register values in set_cfg() calls -> move functions >> that can fail in the upper part of the function body. >> >> drivers/spi/atmel-quadspi.c | 296 +++++++++++++++++++++++++++++++++++--------- >> 1 file changed, 239 insertions(+), 57 deletions(-) >> >> diff --git a/drivers/spi/atmel-quadspi.c b/drivers/spi/atmel-quadspi.c >> index d3e76acf8517..80c934f3e479 100644 >> --- a/drivers/spi/atmel-quadspi.c >> +++ b/drivers/spi/atmel-quadspi.c >> @@ -19,6 +19,7 @@ >> #include <linux/kernel.h> >> #include <linux/module.h> >> #include <linux/of.h> >> +#include <linux/of_platform.h> >> #include <linux/platform_device.h> >> #include <linux/spi/spi-mem.h> >> >> @@ -35,7 +36,9 @@ >> >> #define QSPI_IAR 0x0030 /* Instruction Address Register */ >> #define QSPI_ICR 0x0034 /* Instruction Code Register */ >> +#define QSPI_WICR 0x0034 /* Write Instruction Code Register */ >> #define QSPI_IFR 0x0038 /* Instruction Frame Register */ >> +#define QSPI_RICR 0x003C /* Read Instruction Code Register */ >> >> #define QSPI_SMR 0x0040 /* Scrambling Mode Register */ >> #define QSPI_SKR 0x0044 /* Scrambling Key Register */ >> @@ -88,7 +91,7 @@ >> #define QSPI_SCR_DLYBS_MASK GENMASK(23, 16) >> #define QSPI_SCR_DLYBS(n) (((n) << 16) & QSPI_SCR_DLYBS_MASK) >> >> -/* Bitfields in QSPI_ICR (Instruction Code Register) */ >> +/* Bitfields in QSPI_ICR (Read/Write Instruction Code Register) */ >> #define QSPI_ICR_INST_MASK GENMASK(7, 0) >> #define QSPI_ICR_INST(inst) (((inst) << 0) & QSPI_ICR_INST_MASK) >> #define QSPI_ICR_OPT_MASK GENMASK(23, 16) >> @@ -113,6 +116,8 @@ >> #define QSPI_IFR_OPTL_4BIT (2 << 8) >> #define QSPI_IFR_OPTL_8BIT (3 << 8) >> #define QSPI_IFR_ADDRL BIT(10) >> +#define QSPI_IFR_TFRTYP_TRSFR_MEM BIT(12) >> +#define QSPI_IFR_TFRTYP_TRSFR_REG (0 << 12) > > You don't need to define TRSFR_REG, just set QSPI_IFR_TFRTYP_TRSFR_MEM > when you do a mem transfer and do nothing when this is a regular > transfer. I chose to introduce macros with zero value for better code readability. I would expect that the NOP operations to be optimized at compile time. I will remove them if you prefer, it will result in fewer lines of code. > >> #define QSPI_IFR_TFRTYP_MASK GENMASK(13, 12) >> #define QSPI_IFR_TFRTYP_TRSFR_READ (0 << 12) >> #define QSPI_IFR_TFRTYP_TRSFR_READ_MEM (1 << 12) > > Looks like the read/write flag is on bit 13. Can we just add for sama5d2 only > > #define QSPI_IFR_TFRTYP_TRSFR_WRITE BIT(13) > > and drop all others def? This way the implementation is consistent > between sam9x60 and sama5d2. BIT(13) has no meaning for sam9x60. I can drop the macros with zero value for sama5d2 in a separate patch. > >> @@ -121,6 +126,8 @@ >> #define QSPI_IFR_CRM BIT(14) >> #define QSPI_IFR_NBDUM_MASK GENMASK(20, 16) >> #define QSPI_IFR_NBDUM(n) (((n) << 16) & QSPI_IFR_NBDUM_MASK) >> +#define QSPI_IFR_APBTFRTYP_WRITE (0 << 24) > > As for the other defs, I don't think you need to define _WRITE. understood > >> +#define QSPI_IFR_APBTFRTYP_READ BIT(24) >> >> /* Bitfields in QSPI_SMR (Scrambling Mode Register) */ >> #define QSPI_SMR_SCREN BIT(0) >> @@ -137,16 +144,37 @@ >> #define QSPI_WPSR_WPVSRC(src) (((src) << 8) & QSPI_WPSR_WPVSRC) >> >> >> +/* Describes register values. */ >> +struct atmel_qspi_cfg { >> + u32 icr; >> + u32 iar; >> + u32 ifr; >> +}; >> + >> +struct atmel_qspi_caps; >> + >> struct atmel_qspi { >> void __iomem *regs; >> void __iomem *mem; >> struct clk *clk; > > Can we rename that on pclk? will rename it, together with the support for unnamed clock of sama5d2 in a separate patch. The dt-bindings patch that imposes "pclk" for sama5d2 should be separated too. > >> + struct clk *qspick; >> struct platform_device *pdev; >> + const struct atmel_qspi_caps *caps; >> u32 pending; >> u32 mr; >> struct completion cmd_completion; >> }; >> > > ... > >> + >> +static int atmel_sam9x60_qspi_set_cfg(void __iomem *base, >> + const struct spi_mem_op *op, >> + struct atmel_qspi_cfg *cfg) >> +{ >> + int ret = atmel_qspi_set_mode(cfg, op); >> + >> + if (ret) >> + return ret; >> + >> + ret = atmel_qspi_set_address_mode(cfg, op); >> + if (ret) >> + return ret; >> + >> + cfg->ifr |= QSPI_IFR_INSTEN; >> + cfg->icr |= QSPI_ICR_INST(op->cmd.opcode); >> + >> + /* Set data enable */ >> + if (op->data.nbytes) >> + cfg->ifr |= QSPI_IFR_DATAEN; >> + >> + if (!op->addr.nbytes) { >> + cfg->ifr |= QSPI_IFR_TFRTYP_TRSFR_REG; >> + if (op->data.dir == SPI_MEM_DATA_OUT) >> + cfg->ifr |= QSPI_IFR_APBTFRTYP_WRITE; >> + else >> + cfg->ifr |= QSPI_IFR_APBTFRTYP_READ; >> + } else { >> + cfg->ifr |= QSPI_IFR_TFRTYP_TRSFR_MEM; > > Can you try doing only regular transfers and let me know if it still > works. Support for mem transfers can then be added along with dirmap > support. should work. Will try and let you know. > >> + } >> >> /* Clear pending interrupts */ >> (void)readl_relaxed(base + QSPI_SR); >> >> /* Set QSPI Instruction Frame registers */ >> - writel_relaxed(iar, base + QSPI_IAR); >> - writel_relaxed(icr, base + QSPI_ICR); >> - writel_relaxed(ifr, base + QSPI_IFR); >> + writel_relaxed(cfg->iar, base + QSPI_IAR); >> + if (op->data.dir == SPI_MEM_DATA_OUT) >> + writel_relaxed(cfg->icr, base + QSPI_ICR); >> + else >> + writel_relaxed(cfg->icr, base + QSPI_RICR); >> + writel_relaxed(cfg->ifr, base + QSPI_IFR); >> + >> + return 0; >> +} >> + > > ... > >> @@ -443,32 +578,52 @@ static int atmel_qspi_probe(struct platform_device *pdev) >> /* Enable the peripheral clock */ >> err = clk_prepare_enable(aq->clk); >> if (err) { >> - dev_err(&pdev->dev, "failed to enable the peripheral clock\n"); >> + dev_err(dev, "failed to enable the peripheral clock\n"); >> goto exit; >> } >> >> + if (caps->has_qspick) { >> + /* Get the QSPI system clock */ >> + aq->qspick = devm_clk_get(dev, "qspick"); >> + if (IS_ERR(aq->qspick)) { >> + dev_err(dev, "missing system clock\n"); >> + err = PTR_ERR(aq->qspick); >> + goto disable_clk; >> + } >> + >> + /* Enable the QSPI system clock */ >> + err = clk_prepare_enable(aq->qspick); >> + if (err) { >> + dev_err(dev, >> + "failed to enable the QSPI system clock\n"); >> + goto disable_clk; >> + } >> + } >> + >> /* Request the IRQ */ >> irq = platform_get_irq(pdev, 0); >> if (irq < 0) { >> - dev_err(&pdev->dev, "missing IRQ\n"); >> + dev_err(dev, "missing IRQ\n"); >> err = irq; >> - goto disable_clk; >> + goto disable_qspick; >> } >> - err = devm_request_irq(&pdev->dev, irq, atmel_qspi_interrupt, >> - 0, dev_name(&pdev->dev), aq); >> + err = devm_request_irq(dev, irq, atmel_qspi_interrupt, 0, >> + dev_name(dev), aq); >> if (err) >> - goto disable_clk; >> + goto disable_qspick; >> >> err = atmel_qspi_init(aq); >> if (err) >> - goto disable_clk; >> + goto disable_qspick; >> >> err = spi_register_controller(ctrl); >> if (err) >> - goto disable_clk; >> + goto disable_qspick; >> >> return 0; >> >> +disable_qspick: >> + clk_disable_unprepare(aq->qspick); >> disable_clk: > > We should probably rename this label disable_pclk. sure. Thanks, Boris! > >> clk_disable_unprepare(aq->clk); >> exit: >
On Fri, 1 Feb 2019 07:07:40 +0000 <Tudor.Ambarus@microchip.com> wrote: > > > >> #define QSPI_IFR_TFRTYP_MASK GENMASK(13, 12) > >> #define QSPI_IFR_TFRTYP_TRSFR_READ (0 << 12) > >> #define QSPI_IFR_TFRTYP_TRSFR_READ_MEM (1 << 12) > > > > Looks like the read/write flag is on bit 13. Can we just add > > for sama5d2 only Feel free to prefix macros with the SoC name to make it clear: #define QSPI_IFR_SAMA5D2_WRITE_TRSFR BIT(13) > > > > > #define QSPI_IFR_TFRTYP_TRSFR_WRITE BIT(13) > > > > and drop all others def? This way the implementation is consistent > > between sam9x60 and sama5d2. > > BIT(13) has no meaning for sam9x60. I can drop the macros with zero value for > sama5d2 in a separate patch. > > > >> +#define QSPI_IFR_APBTFRTYP_READ BIT(24) And this one would be define QSPI_IFR_SAM9X60_READ_TRSFR BIT(24) > >> > >> /* Bitfields in QSPI_SMR (Scrambling Mode Register) */ > >> #define QSPI_SMR_SCREN BIT(0) > >> @@ -137,16 +144,37 @@ > >> #define QSPI_WPSR_WPVSRC(src) (((src) << 8) & QSPI_WPSR_WPVSRC) > >> > >> > >> +/* Describes register values. */ > >> +struct atmel_qspi_cfg { > >> + u32 icr; > >> + u32 iar; > >> + u32 ifr; > >> +}; > >> + > >> +struct atmel_qspi_caps; > >> + > >> struct atmel_qspi { > >> void __iomem *regs; > >> void __iomem *mem; > >> struct clk *clk; > > > > Can we rename that on pclk? > > will rename it, together with the support for unnamed clock of sama5d2 in a separate > patch. The dt-bindings patch that imposes "pclk" for sama5d2 should be separated too. Sounds good.
On 02/01/2019 09:07 AM, Tudor.Ambarus@microchip.com wrote: cut >>> diff --git a/drivers/spi/atmel-quadspi.c b/drivers/spi/atmel-quadspi.c cut >>> +static int atmel_sam9x60_qspi_set_cfg(void __iomem *base, >>> + const struct spi_mem_op *op, >>> + struct atmel_qspi_cfg *cfg) >>> +{ >>> + int ret = atmel_qspi_set_mode(cfg, op); >>> + >>> + if (ret) >>> + return ret; >>> + >>> + ret = atmel_qspi_set_address_mode(cfg, op); >>> + if (ret) >>> + return ret; >>> + >>> + cfg->ifr |= QSPI_IFR_INSTEN; >>> + cfg->icr |= QSPI_ICR_INST(op->cmd.opcode); >>> + >>> + /* Set data enable */ >>> + if (op->data.nbytes) >>> + cfg->ifr |= QSPI_IFR_DATAEN; >>> + >>> + if (!op->addr.nbytes) { >>> + cfg->ifr |= QSPI_IFR_TFRTYP_TRSFR_REG; >>> + if (op->data.dir == SPI_MEM_DATA_OUT) >>> + cfg->ifr |= QSPI_IFR_APBTFRTYP_WRITE; >>> + else >>> + cfg->ifr |= QSPI_IFR_APBTFRTYP_READ; >>> + } else { >>> + cfg->ifr |= QSPI_IFR_TFRTYP_TRSFR_MEM; >> >> Can you try doing only regular transfers and let me know if it still >> works. Support for mem transfers can then be added along with dirmap >> support. > > should work. Will try and let you know. you were right, it works. I will let mem transfer logic for dirmap support. Cheers, ta
On 02/01/2019 09:57 AM, Boris Brezillon wrote: > On Fri, 1 Feb 2019 07:07:40 +0000 > <Tudor.Ambarus@microchip.com> wrote: > >>> >>>> #define QSPI_IFR_TFRTYP_MASK GENMASK(13, 12) >>>> #define QSPI_IFR_TFRTYP_TRSFR_READ (0 << 12) >>>> #define QSPI_IFR_TFRTYP_TRSFR_READ_MEM (1 << 12) >>> >>> Looks like the read/write flag is on bit 13. Can we just add >> >> for sama5d2 only > > Feel free to prefix macros with the SoC name to make it clear: > > #define QSPI_IFR_SAMA5D2_WRITE_TRSFR BIT(13) agreed > cut >>>> +#define QSPI_IFR_APBTFRTYP_READ BIT(24) > > And this one would be > > define QSPI_IFR_SAM9X60_READ_TRSFR BIT(24) I prefer letting this bit named as in the datasheet, QSPI_IFR_APBTFRTYP_READ, and change it if future versions of the IP will modify its sense. It is a READ transfer done on APB, it is more generic this way. If you have a strong opinion on this, please let me know. ta
On Fri, 1 Feb 2019 14:49:27 +0000 <Tudor.Ambarus@microchip.com> wrote: > > >>>> +#define QSPI_IFR_APBTFRTYP_READ BIT(24) > > > > And this one would be > > > > define QSPI_IFR_SAM9X60_READ_TRSFR BIT(24) > > I prefer letting this bit named as in the datasheet, QSPI_IFR_APBTFRTYP_READ, > and change it if future versions of the IP will modify its sense. It is a READ > transfer done on APB, it is more generic this way. If you have a strong opinion > on this, please let me know. As you wish.
From: Tudor Ambarus <tudor.ambarus@microchip.com> Patches from 1 to 8 are minor fixes or cosmetics. Patches 9 and 10 introduce the sam9x60 qspi controller. sam9x60 qspi controller tested with sst26vf064b jedec,spi-nor flash. Backward compatibility test done on sama5d2 qspi controller and mx25l25635e jedec,spi-nor flash. The patches are generated on top of for-next branch. v2: - cache MR value, - drop iomem wrappers, - make "pclk" clock-name mandatory even for sama5d2, - rework clock handling, - reorder setting of register values in set_cfg() calls, - collect R-b tags. Tudor Ambarus (10): spi: atmel-quadspi: cache MR value to avoid a write access spi: atmel-quadspi: order header files inclusion alphabetically spi: atmel-quadspi: drop wrappers for iomem accesses spi: atmel-quadspi: fix naming scheme spi: atmel-quadspi: remove unnecessary cast spi: atmel-quadspi: return appropriate error code spi: atmel-quadspi: switch to SPDX license identifiers dt-bindings: spi: atmel-quadspi: update example to new clock binding dt-bindings: spi: atmel-quadspi: QuadSPI driver for Microchip SAM9X60 spi: atmel-quadspi: add support for sam9x60 qspi controller .../devicetree/bindings/spi/atmel-quadspi.txt | 14 +- drivers/spi/atmel-quadspi.c | 374 +++++++++++++++------ 2 files changed, 281 insertions(+), 107 deletions(-)