Message ID | 1515058844-16007-1-git-send-email-sivadur@xilinx.com |
---|---|
Headers | show |
Series | Add support of SD3.0 UHS modes for ZynqMP | expand |
Hi Jaehoon, Any review comments on this. Thanks, Siva > -----Original Message----- > From: Siva Durga Prasad Paladugu [mailto:siva.durga.paladugu@xilinx.com] > Sent: Thursday, January 04, 2018 3:11 PM > To: u-boot@lists.denx.de > Cc: jh80.chung@samsung.com; Siva Durga Prasad Paladugu > <sivadur@xilinx.com> > Subject: [PATCH v2 0/7] Add support of SD3.0 UHS modes for ZynqMP > > This patch series is meant to add SD3.0 support for ZynqMP platform. > The first five patches in the series mostly setting up things in sdhci layer to > support SD3.0 , the sixth patch is to add SD3.0 support for ZynqMP > platform and the last patch is to enable this support for ZynqMP zcu102 > rev1.0 eval board. > > Repo: u-boot-mmc.git > Branch: hs200-working > > Siva Durga Prasad Paladugu (7): > mmc: sdhci: Add support for disabling clock > mmc: sdhci: Handle execute tuning command in sdhci_send_command > sdhci: Add new sdhci ops for platform specific tuning and delays > mmc: sdhci: Invoke platform specific tuning and delay routines > mmc : sdhci: Read capabilities register1 and update host caps > mmc: zynq_sdhci: Add support for SD3.0 > zynqmp: zcu102: Enable UHS support for ZCU102 Rev1.0 board > > board/xilinx/zynqmp/Makefile | 2 + > board/xilinx/zynqmp/tap_delays.c | 230 > ++++++++++++++++++++++++++ > configs/xilinx_zynqmp_zcu102_rev1_0_defconfig | 2 + > drivers/mmc/sdhci.c | 67 +++++++- > drivers/mmc/zynq_sdhci.c | 230 > +++++++++++++++++++++++++- > include/sdhci.h | 9 + > include/zynqmp_tap_delay.h | 20 +++ > 7 files changed, 550 insertions(+), 10 deletions(-) create mode 100644 > board/xilinx/zynqmp/tap_delays.c create mode 100644 > include/zynqmp_tap_delay.h > > -- > 2.7.4
Hi Siva, On 01/16/2018 07:10 PM, Siva Durga Prasad Paladugu wrote: > Hi Jaehoon, > > Any review comments on this. Thanks for reminding. Will check! :) Best Regards, Jaehoon Chung > > Thanks, > Siva > >> -----Original Message----- >> From: Siva Durga Prasad Paladugu [mailto:siva.durga.paladugu@xilinx.com] >> Sent: Thursday, January 04, 2018 3:11 PM >> To: u-boot@lists.denx.de >> Cc: jh80.chung@samsung.com; Siva Durga Prasad Paladugu >> <sivadur@xilinx.com> >> Subject: [PATCH v2 0/7] Add support of SD3.0 UHS modes for ZynqMP >> >> This patch series is meant to add SD3.0 support for ZynqMP platform. >> The first five patches in the series mostly setting up things in sdhci layer to >> support SD3.0 , the sixth patch is to add SD3.0 support for ZynqMP >> platform and the last patch is to enable this support for ZynqMP zcu102 >> rev1.0 eval board. >> >> Repo: u-boot-mmc.git >> Branch: hs200-working >> >> Siva Durga Prasad Paladugu (7): >> mmc: sdhci: Add support for disabling clock >> mmc: sdhci: Handle execute tuning command in sdhci_send_command >> sdhci: Add new sdhci ops for platform specific tuning and delays >> mmc: sdhci: Invoke platform specific tuning and delay routines >> mmc : sdhci: Read capabilities register1 and update host caps >> mmc: zynq_sdhci: Add support for SD3.0 >> zynqmp: zcu102: Enable UHS support for ZCU102 Rev1.0 board >> >> board/xilinx/zynqmp/Makefile | 2 + >> board/xilinx/zynqmp/tap_delays.c | 230 >> ++++++++++++++++++++++++++ >> configs/xilinx_zynqmp_zcu102_rev1_0_defconfig | 2 + >> drivers/mmc/sdhci.c | 67 +++++++- >> drivers/mmc/zynq_sdhci.c | 230 >> +++++++++++++++++++++++++- >> include/sdhci.h | 9 + >> include/zynqmp_tap_delay.h | 20 +++ >> 7 files changed, 550 insertions(+), 10 deletions(-) create mode 100644 >> board/xilinx/zynqmp/tap_delays.c create mode 100644 >> include/zynqmp_tap_delay.h >> >> -- >> 2.7.4 > > > >
Hi Jaehoon, I would like to send v3 for this series, Any specific branch that you want me to rebase the series? Thanks, DP > -----Original Message----- > From: Jaehoon Chung [mailto:jh80.chung@samsung.com] > Sent: Wednesday, January 17, 2018 8:04 AM > To: Siva Durga Prasad Paladugu <sivadur@xilinx.com>; u- > boot@lists.denx.de > Subject: Re: [PATCH v2 0/7] Add support of SD3.0 UHS modes for ZynqMP > > Hi Siva, > > On 01/16/2018 07:10 PM, Siva Durga Prasad Paladugu wrote: > > Hi Jaehoon, > > > > Any review comments on this. > > Thanks for reminding. Will check! :) > > Best Regards, > Jaehoon Chung > > > > Thanks, > > Siva > > > >> -----Original Message----- > >> From: Siva Durga Prasad Paladugu > >> [mailto:siva.durga.paladugu@xilinx.com] > >> Sent: Thursday, January 04, 2018 3:11 PM > >> To: u-boot@lists.denx.de > >> Cc: jh80.chung@samsung.com; Siva Durga Prasad Paladugu > >> <sivadur@xilinx.com> > >> Subject: [PATCH v2 0/7] Add support of SD3.0 UHS modes for ZynqMP > >> > >> This patch series is meant to add SD3.0 support for ZynqMP platform. > >> The first five patches in the series mostly setting up things in > >> sdhci layer to support SD3.0 , the sixth patch is to add SD3.0 > >> support for ZynqMP platform and the last patch is to enable this > >> support for ZynqMP zcu102 > >> rev1.0 eval board. > >> > >> Repo: u-boot-mmc.git > >> Branch: hs200-working > >> > >> Siva Durga Prasad Paladugu (7): > >> mmc: sdhci: Add support for disabling clock > >> mmc: sdhci: Handle execute tuning command in sdhci_send_command > >> sdhci: Add new sdhci ops for platform specific tuning and delays > >> mmc: sdhci: Invoke platform specific tuning and delay routines > >> mmc : sdhci: Read capabilities register1 and update host caps > >> mmc: zynq_sdhci: Add support for SD3.0 > >> zynqmp: zcu102: Enable UHS support for ZCU102 Rev1.0 board > >> > >> board/xilinx/zynqmp/Makefile | 2 + > >> board/xilinx/zynqmp/tap_delays.c | 230 > >> ++++++++++++++++++++++++++ > >> configs/xilinx_zynqmp_zcu102_rev1_0_defconfig | 2 + > >> drivers/mmc/sdhci.c | 67 +++++++- > >> drivers/mmc/zynq_sdhci.c | 230 > >> +++++++++++++++++++++++++- > >> include/sdhci.h | 9 + > >> include/zynqmp_tap_delay.h | 20 +++ > >> 7 files changed, 550 insertions(+), 10 deletions(-) create mode > >> 100644 board/xilinx/zynqmp/tap_delays.c create mode 100644 > >> include/zynqmp_tap_delay.h > >> > >> -- > >> 2.7.4 > > > > > > > >
Hi Jaehoon, Ping! Thanks, Siva > -----Original Message----- > From: Siva Durga Prasad Paladugu > Sent: Tuesday, April 10, 2018 12:02 PM > To: Jaehoon Chung <jh80.chung@samsung.com>; u-boot@lists.denx.de > Subject: RE: [PATCH v2 0/7] Add support of SD3.0 UHS modes for ZynqMP > > Hi Jaehoon, > > I would like to send v3 for this series, Any specific branch that you want me > to rebase the series? > > Thanks, > DP > > > -----Original Message----- > > From: Jaehoon Chung [mailto:jh80.chung@samsung.com] > > Sent: Wednesday, January 17, 2018 8:04 AM > > To: Siva Durga Prasad Paladugu <sivadur@xilinx.com>; u- > > boot@lists.denx.de > > Subject: Re: [PATCH v2 0/7] Add support of SD3.0 UHS modes for > ZynqMP > > > > Hi Siva, > > > > On 01/16/2018 07:10 PM, Siva Durga Prasad Paladugu wrote: > > > Hi Jaehoon, > > > > > > Any review comments on this. > > > > Thanks for reminding. Will check! :) > > > > Best Regards, > > Jaehoon Chung > > > > > > Thanks, > > > Siva > > > > > >> -----Original Message----- > > >> From: Siva Durga Prasad Paladugu > > >> [mailto:siva.durga.paladugu@xilinx.com] > > >> Sent: Thursday, January 04, 2018 3:11 PM > > >> To: u-boot@lists.denx.de > > >> Cc: jh80.chung@samsung.com; Siva Durga Prasad Paladugu > > >> <sivadur@xilinx.com> > > >> Subject: [PATCH v2 0/7] Add support of SD3.0 UHS modes for ZynqMP > > >> > > >> This patch series is meant to add SD3.0 support for ZynqMP platform. > > >> The first five patches in the series mostly setting up things in > > >> sdhci layer to support SD3.0 , the sixth patch is to add SD3.0 > > >> support for ZynqMP platform and the last patch is to enable this > > >> support for ZynqMP zcu102 > > >> rev1.0 eval board. > > >> > > >> Repo: u-boot-mmc.git > > >> Branch: hs200-working > > >> > > >> Siva Durga Prasad Paladugu (7): > > >> mmc: sdhci: Add support for disabling clock > > >> mmc: sdhci: Handle execute tuning command in > sdhci_send_command > > >> sdhci: Add new sdhci ops for platform specific tuning and delays > > >> mmc: sdhci: Invoke platform specific tuning and delay routines > > >> mmc : sdhci: Read capabilities register1 and update host caps > > >> mmc: zynq_sdhci: Add support for SD3.0 > > >> zynqmp: zcu102: Enable UHS support for ZCU102 Rev1.0 board > > >> > > >> board/xilinx/zynqmp/Makefile | 2 + > > >> board/xilinx/zynqmp/tap_delays.c | 230 > > >> ++++++++++++++++++++++++++ > > >> configs/xilinx_zynqmp_zcu102_rev1_0_defconfig | 2 + > > >> drivers/mmc/sdhci.c | 67 +++++++- > > >> drivers/mmc/zynq_sdhci.c | 230 > > >> +++++++++++++++++++++++++- > > >> include/sdhci.h | 9 + > > >> include/zynqmp_tap_delay.h | 20 +++ > > >> 7 files changed, 550 insertions(+), 10 deletions(-) create mode > > >> 100644 board/xilinx/zynqmp/tap_delays.c create mode 100644 > > >> include/zynqmp_tap_delay.h > > >> > > >> -- > > >> 2.7.4 > > > > > > > > > > > >