Message ID | cover.1506683482.git.horms+renesas@verge.net.au |
---|---|
State | New |
Headers | show |
Series | [GIT,PULL] Renesas ARM Based SoC DT Updates for v4.15 | expand |
Hello! On 9/29/2017 2:53 PM, Simon Horman wrote: > From: Jacopo Mondi <jacopo+renesas@jmondi.org> > > Add device nodes for user leds on gr-peach board. > > Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> > Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> > Signed-off-by: Simon Horman <horms+renesas@verge.net.au> > --- > arch/arm/boot/dts/r7s72100-gr-peach.dts | 10 ++++++++++ > 1 file changed, 10 insertions(+) > > diff --git a/arch/arm/boot/dts/r7s72100-gr-peach.dts b/arch/arm/boot/dts/r7s72100-gr-peach.dts > index bcfa6445bbaa..13d745bb56a5 100644 > --- a/arch/arm/boot/dts/r7s72100-gr-peach.dts > +++ b/arch/arm/boot/dts/r7s72100-gr-peach.dts [...] > @@ -51,6 +52,15 @@ > reg = <0x00600000 0x00200000>; > }; > }; > + > +leds { Not indented properly... > + status = "okay"; > + compatible = "gpio-leds"; > + > + led1 { > + gpios = <&port6 12 GPIO_ACTIVE_HIGH>; > + }; > + }; > }; > > &pinctrl { MBR, Sergei
Hi Seregei, On Sat, Sep 30, 2017 at 01:36:18PM +0300, Sergei Shtylyov wrote: > Hello! > > On 9/29/2017 2:53 PM, Simon Horman wrote: > > >From: Jacopo Mondi <jacopo+renesas@jmondi.org> > > > >Add device nodes for user leds on gr-peach board. > > > >Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> > >Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> > >Signed-off-by: Simon Horman <horms+renesas@verge.net.au> > >--- > > arch/arm/boot/dts/r7s72100-gr-peach.dts | 10 ++++++++++ > > 1 file changed, 10 insertions(+) > > > >diff --git a/arch/arm/boot/dts/r7s72100-gr-peach.dts b/arch/arm/boot/dts/r7s72100-gr-peach.dts > >index bcfa6445bbaa..13d745bb56a5 100644 > >--- a/arch/arm/boot/dts/r7s72100-gr-peach.dts > >+++ b/arch/arm/boot/dts/r7s72100-gr-peach.dts > [...] > >@@ -51,6 +52,15 @@ > > reg = <0x00600000 0x00200000>; > > }; > > }; > >+ > >+leds { > > Not indented properly... Thanks! Simon, as you sent pull request already, will we need a patch on top of this to fix it? Thanks j > > >+ status = "okay"; > >+ compatible = "gpio-leds"; > >+ > >+ led1 { > >+ gpios = <&port6 12 GPIO_ACTIVE_HIGH>; > >+ }; > >+ }; > > }; > > &pinctrl { > > MBR, Sergei
On Sun, Oct 01, 2017 at 07:36:14PM +0200, jacopo mondi wrote: > Hi Seregei, > > On Sat, Sep 30, 2017 at 01:36:18PM +0300, Sergei Shtylyov wrote: > > Hello! > > > > On 9/29/2017 2:53 PM, Simon Horman wrote: > > > > >From: Jacopo Mondi <jacopo+renesas@jmondi.org> > > > > > >Add device nodes for user leds on gr-peach board. > > > > > >Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org> > > >Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> > > >Signed-off-by: Simon Horman <horms+renesas@verge.net.au> > > >--- > > > arch/arm/boot/dts/r7s72100-gr-peach.dts | 10 ++++++++++ > > > 1 file changed, 10 insertions(+) > > > > > >diff --git a/arch/arm/boot/dts/r7s72100-gr-peach.dts b/arch/arm/boot/dts/r7s72100-gr-peach.dts > > >index bcfa6445bbaa..13d745bb56a5 100644 > > >--- a/arch/arm/boot/dts/r7s72100-gr-peach.dts > > >+++ b/arch/arm/boot/dts/r7s72100-gr-peach.dts > > [...] > > >@@ -51,6 +52,15 @@ > > > reg = <0x00600000 0x00200000>; > > > }; > > > }; > > >+ > > >+leds { > > > > Not indented properly... > > Thanks! > > Simon, as you sent pull request already, will we need a patch on top > of this to fix it? Thanks, please do. I don't think we need to re-spin the pull-request to correct this, rather, a follow-up patch can be provided in a follow-up pull-request. > > Thanks > j > > > > >+ status = "okay"; > > >+ compatible = "gpio-leds"; > > >+ > > >+ led1 { > > >+ gpios = <&port6 12 GPIO_ACTIVE_HIGH>; > > >+ }; > > >+ }; > > > }; > > > &pinctrl { > > > > MBR, Sergei >
On Fri, Sep 29, 2017 at 1:53 PM, Simon Horman <horms+renesas@verge.net.au> wrote: > ---------------------------------------------------------------- > Renesas ARM Based SoC DT Updates for v4.15 > > * r7s72100 (RZ/A1) Peach board > - Add pin groups for SCIF2 serial debug interface and Ethernet > This avoids relying on bootloader settings > - Support control of LED1 using gpio-leds > > * r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs > - Add MSIOF[012] support and define aliases for spi[0123] > > * r8a7743 (RZ/G1M) SoC > - Add I2C and IIC core nodes > > * r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven development platform > - Enable SDHI1 SD controller supporting high-speed and SDR50 transfers > - Add chosen node to allow correct selection of serial console > and the kernel command line > - Enable RTC support > - Enable USB2.0 host support > This includes enabling USB PHY and internal PCI > > * r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven and > r8a7745 (RZ/G1E) iW-RainboW-G22M-SM SoMs > - Enable Add SPI NOR support > This devices is used to boot up the system to the SoM DT > > * r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven SoM > - Enable SDHI0 SD controller supporting high-speed transfers > > * r8a7745 (RZ/G1E) iW-RainboW-G22D development platform > - Add pnctl support for scif4 > This avoids reling on boot loader settings > - Add EtherAVB support > > * r8a7745 (RZ/G1E) iW-RainboW-G22M-SM SoM > - Add basic SoM support > - Enable MMCIF eMMC support > - Enable RTC support > - Enable SDHI1 SD controller supporting high-speed transfers > > * r8a779[0-4] R-Car Gen2 SoCs > - Add reset control properties > Geert Uytterhoeven says: > > This patch series describes the reset topology on all R-Car Gen2 Socs, > like was done before for R-Car Gen3 and RZ/G1. > > Resets usually match the corresponding module clocks. Exceptions are: > - The audio module has resets for the Serial Sound Interfaces only, > - The display module has only a single reset for all DU channels, but > adding reset properties for the display is postponed upon request > from Laurent. > > - Convert to new CPG/MSSR bindings > Geert Uytterhoven says: > > Currently Renesas R-Car Gen2 SoCs use the common clk-rcar-gen2, > clk-mstp, and clk-div6 drivers, which depend on most clocks being > described in DT. Especially the module (MSTP) clocks are cumbersome > and error prone, due to 3 arrays (clocks, clock-indices, and > clock-output-names) to be kept in sync. In addition, the clk-mstp > driver cannot be extended easily to also support module resets, which > are provided by the same hardware module. > > Hence when developing support for R-Car Gen3 SoCs, another approach > was chosen, which led to the CPG/MSSR driver core, and SoC-specific > subdrivers (initially for R-Car Gen3, but later also for RZ/G1). > > This series converts the various R-Car Gen2 DTSes to migrate to the > new CPG/MSSR drivers that were added in v4.13-rc1. > > * r8a779[0,1,3,4] R-Car Gen2 SoCs > - Stop grouping clocks under a "clocks" subnode > Geert Uytterhoeven says: > > The current practice is to not group clocks under a "clocks" subnode, > but just put them together with the other on-SoC devices. > > Hence this patch series implements this for the various R-Car Gen2 > DTSes that still need this (r8a7792.dtsi is OK). > > * r8a7794 (E2) Alt board > - Correct inverted sense of SD wip pins Pulled into next/dt, thanks! Arnd