Message ID | 1489781473-30772-1-git-send-email-mdf@kernel.org |
---|---|
State | Changes Requested, archived |
Headers | show |
On 17.3.2017 21:11, Moritz Fischer wrote: > This adds support for the Xilinx LogiCORE PR Decoupler > soft-ip that does decoupling of PR regions in the FPGA > fabric during partial reconfiguration. > > Signed-off-by: Moritz Fischer <mdf@kernel.org> > Cc: Michal Simek <michal.simek@xilinx.com> > Cc: Sören Brinkmann <soren.brinkmann@xilinx.com> > Cc: linux-kernel@vger.kernel.org > Cc: devicetree@vger.kernel.org > --- > Changes from v2: > - Added Michal's Signed-off-by btw: you forgot to add it above. :-) > - Added "xlnx,pr-decoupler" unversioned fallback > > Changes from v1: > - Added Michal as Co-Author since I pulled in some of his code > - Reworked clk handling in _remove() > - Pulled in Michal's version of show_enable(), ditched priv->enabled > > --- > drivers/fpga/Kconfig | 9 +++ > drivers/fpga/Makefile | 1 + > drivers/fpga/xilinx-pr-decoupler.c | 148 +++++++++++++++++++++++++++++++++++++ > 3 files changed, 158 insertions(+) > create mode 100644 drivers/fpga/xilinx-pr-decoupler.c > > diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig > index ce861a2..ce0c91d 100644 > --- a/drivers/fpga/Kconfig > +++ b/drivers/fpga/Kconfig > @@ -63,6 +63,15 @@ config ALTERA_FREEZE_BRIDGE > isolate one region of the FPGA from the busses while that > region is being reprogrammed. > > +config XILINX_PR_DECOUPLER > + tristate "Xilinx LogiCORE PR Decoupler" > + depends on FPGA_BRIDGE > + help > + Say Y to enable drivers for Xilinx LogiCORE PR Decoupler. > + The PR Decoupler exists in the FPGA fabric to isolate one > + region of the FPGA from the busses while that region is > + being reprogrammed during partial reconfig. > + > endif # FPGA > > endmenu > diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile > index 8df07bc..ba94b79 100644 > --- a/drivers/fpga/Makefile > +++ b/drivers/fpga/Makefile > @@ -14,6 +14,7 @@ obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA) += zynq-fpga.o > obj-$(CONFIG_FPGA_BRIDGE) += fpga-bridge.o > obj-$(CONFIG_SOCFPGA_FPGA_BRIDGE) += altera-hps2fpga.o altera-fpga2sdram.o > obj-$(CONFIG_ALTERA_FREEZE_BRIDGE) += altera-freeze-bridge.o > +obj-$(CONFIG_XILINX_PR_DECOUPLER) += xilinx-pr-decoupler.o > > # High Level Interfaces > obj-$(CONFIG_FPGA_REGION) += fpga-region.o > diff --git a/drivers/fpga/xilinx-pr-decoupler.c b/drivers/fpga/xilinx-pr-decoupler.c > new file mode 100644 > index 0000000..dd37b1c > --- /dev/null > +++ b/drivers/fpga/xilinx-pr-decoupler.c > @@ -0,0 +1,148 @@ > +/* > + * Copyright (c) 2017, National Instruments Corp. > + * Copyright (c) 2017, Xilix Inc > + * > + * FPGA Bridge Driver for the Xilinx LogiCORE Partial Reconfiguration > + * Decoupler IP Core. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; version 2 of the License. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + */ > + > +#include <linux/clk.h> > +#include <linux/io.h> > +#include <linux/kernel.h> > +#include <linux/of_device.h> > +#include <linux/module.h> > +#include <linux/fpga/fpga-bridge.h> > + > +#define CTRL_CMD_DECOUPLE BIT(0) > +#define CTRL_CMD_COUPLE ~BIT(0) for others - this was reported by 0-day testing system as a warning. M -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 17.3.2017 21:11, Moritz Fischer wrote: > This adds the binding documentation for the Xilinx LogiCORE PR > Decoupler soft core. > > Signed-off-by: Moritz Fischer <mdf@kernel.org> > Cc: Michal Simek <michal.simek@xilinx.com> > Cc: Sören Brinkmann <soren.brinkmann@xilinx.com> > Cc: linux-kernel@vger.kernel.org > Cc: devicetree@vger.kernel.org > --- > > Changes from v2: > - Added refence to generic fpga-region bindings > - Fixed up reg property in example > - Added fallback to "xlnx,pr-decoupler" without version > > Changes from v1: > - Added clock names & clock to example > - Merged some of the description from Michal's version > > --- > .../bindings/fpga/xilinx-pr-decoupler.txt | 35 ++++++++++++++++++++++ > 1 file changed, 35 insertions(+) > create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt > > diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt > new file mode 100644 > index 0000000..16141bd > --- /dev/null > +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt > @@ -0,0 +1,35 @@ > +Xilinx LogiCORE Partial Reconfig Decoupler Softcore > + > +The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more > +decouplers / fpga bridges. > +The controller can decouple/disable the bridges which prevents signal > +changes from passing through the bridge. The controller can also > +couple / enable the bridges which allows traffic to pass through the > +bridge normally. > + > +The Driver supports only MMIO handling. A PR region can have multiple > +PR Decouples which can bhe handled independently or chaines via decouple/ > +decouple_status signals. > + > +Required properties: > +- compatible : Should contain "xlnx,pr-decoupler-1.00" here should be also that "xlnx-pr-decoupler" too. Other than this all looks good. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Thanks, Michal -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Fri, Mar 17, 2017 at 3:11 PM, Moritz Fischer <mdf@kernel.org> wrote: Hi Moritz, Minor nits below. Otherwise, looks good. > This adds the binding documentation for the Xilinx LogiCORE PR > Decoupler soft core. > > Signed-off-by: Moritz Fischer <mdf@kernel.org> > Cc: Michal Simek <michal.simek@xilinx.com> > Cc: Sören Brinkmann <soren.brinkmann@xilinx.com> > Cc: linux-kernel@vger.kernel.org > Cc: devicetree@vger.kernel.org Acked-by: Alan Tull <atull@kernel.org> > --- > > Changes from v2: > - Added refence to generic fpga-region bindings > - Fixed up reg property in example > - Added fallback to "xlnx,pr-decoupler" without version > > Changes from v1: > - Added clock names & clock to example > - Merged some of the description from Michal's version > > --- > .../bindings/fpga/xilinx-pr-decoupler.txt | 35 ++++++++++++++++++++++ > 1 file changed, 35 insertions(+) > create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt > > diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt > new file mode 100644 > index 0000000..16141bd > --- /dev/null > +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt > @@ -0,0 +1,35 @@ > +Xilinx LogiCORE Partial Reconfig Decoupler Softcore > + > +The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more > +decouplers / fpga bridges. > +The controller can decouple/disable the bridges which prevents signal > +changes from passing through the bridge. The controller can also > +couple / enable the bridges which allows traffic to pass through the > +bridge normally. > + > +The Driver supports only MMIO handling. A PR region can have multiple > +PR Decouples which can bhe handled independently or chaines via decouple/ s/PR Decoupler/PR Decouplers/ s/bhe/be/ s/chaines/chained/ > +decouple_status signals. > + > +Required properties: > +- compatible : Should contain "xlnx,pr-decoupler-1.00" > +- regs : base address and size for decoupler module > +- clocks : input clock to IP > +- clock-names : should contain "aclk" > + > +Optional properties: > +- bridge-enable : 0 if driver should disable bridge at startup > + 1 if driver should enable bridge at startup > + Default is to leave bridge in current state. > + > +See Documentation/devicetree/bindings/fpga/fpga-region.txt for generic bindings. > + > +Example: > + fpga-bridge@100000450 { > + compatible = "xlnx,pr-decoupler-1.00", > + "xlnx-pr-decoupler"; > + regs = <0x10000045 0x10>; > + clocks = <&clkc 15>; > + clock-names = "aclk"; > + bridge-enable = <0>; > + }; > -- > 2.7.4 > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Fri, Mar 17, 2017 at 3:11 PM, Moritz Fischer <mdf@kernel.org> wrote: Hi Moritz, Looks good except for the kbuild robot warnings that need to be fixed. Alan > This adds support for the Xilinx LogiCORE PR Decoupler > soft-ip that does decoupling of PR regions in the FPGA > fabric during partial reconfiguration. > > Signed-off-by: Moritz Fischer <mdf@kernel.org> > Cc: Michal Simek <michal.simek@xilinx.com> > Cc: Sören Brinkmann <soren.brinkmann@xilinx.com> > Cc: linux-kernel@vger.kernel.org > Cc: devicetree@vger.kernel.org > --- > Changes from v2: > - Added Michal's Signed-off-by > - Added "xlnx,pr-decoupler" unversioned fallback > > Changes from v1: > - Added Michal as Co-Author since I pulled in some of his code > - Reworked clk handling in _remove() > - Pulled in Michal's version of show_enable(), ditched priv->enabled > > --- > drivers/fpga/Kconfig | 9 +++ > drivers/fpga/Makefile | 1 + > drivers/fpga/xilinx-pr-decoupler.c | 148 +++++++++++++++++++++++++++++++++++++ > 3 files changed, 158 insertions(+) > create mode 100644 drivers/fpga/xilinx-pr-decoupler.c > > diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig > index ce861a2..ce0c91d 100644 > --- a/drivers/fpga/Kconfig > +++ b/drivers/fpga/Kconfig > @@ -63,6 +63,15 @@ config ALTERA_FREEZE_BRIDGE > isolate one region of the FPGA from the busses while that > region is being reprogrammed. > > +config XILINX_PR_DECOUPLER > + tristate "Xilinx LogiCORE PR Decoupler" > + depends on FPGA_BRIDGE > + help > + Say Y to enable drivers for Xilinx LogiCORE PR Decoupler. > + The PR Decoupler exists in the FPGA fabric to isolate one > + region of the FPGA from the busses while that region is > + being reprogrammed during partial reconfig. > + > endif # FPGA > > endmenu > diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile > index 8df07bc..ba94b79 100644 > --- a/drivers/fpga/Makefile > +++ b/drivers/fpga/Makefile > @@ -14,6 +14,7 @@ obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA) += zynq-fpga.o > obj-$(CONFIG_FPGA_BRIDGE) += fpga-bridge.o > obj-$(CONFIG_SOCFPGA_FPGA_BRIDGE) += altera-hps2fpga.o altera-fpga2sdram.o > obj-$(CONFIG_ALTERA_FREEZE_BRIDGE) += altera-freeze-bridge.o > +obj-$(CONFIG_XILINX_PR_DECOUPLER) += xilinx-pr-decoupler.o > > # High Level Interfaces > obj-$(CONFIG_FPGA_REGION) += fpga-region.o > diff --git a/drivers/fpga/xilinx-pr-decoupler.c b/drivers/fpga/xilinx-pr-decoupler.c > new file mode 100644 > index 0000000..dd37b1c > --- /dev/null > +++ b/drivers/fpga/xilinx-pr-decoupler.c > @@ -0,0 +1,148 @@ > +/* > + * Copyright (c) 2017, National Instruments Corp. > + * Copyright (c) 2017, Xilix Inc > + * > + * FPGA Bridge Driver for the Xilinx LogiCORE Partial Reconfiguration > + * Decoupler IP Core. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; version 2 of the License. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + */ > + > +#include <linux/clk.h> > +#include <linux/io.h> > +#include <linux/kernel.h> > +#include <linux/of_device.h> > +#include <linux/module.h> > +#include <linux/fpga/fpga-bridge.h> > + > +#define CTRL_CMD_DECOUPLE BIT(0) > +#define CTRL_CMD_COUPLE ~BIT(0) > + > +struct xlnx_pr_decoupler_data { > + void __iomem *io_base; > + struct clk *clk; > +}; > + > +static int xlnx_pr_decoupler_enable_set(struct fpga_bridge *bridge, bool enable) > +{ > + int err; > + struct xlnx_pr_decoupler_data *priv = bridge->priv; > + > + err = clk_enable(priv->clk); > + if (err) > + return err; > + > + if (enable) > + writel(CTRL_CMD_COUPLE, priv->io_base); > + else > + writel(CTRL_CMD_DECOUPLE, priv->io_base); > + > + clk_disable(priv->clk); > + > + return 0; > +} > + > +static int xlnx_pr_decoupler_enable_show(struct fpga_bridge *bridge) > +{ > + const struct xlnx_pr_decoupler_data *priv = bridge->priv; > + u32 status; > + int err; > + > + err = clk_enable(priv->clk); > + if (err) > + return err; > + > + status = readl(priv->io_base); > + > + clk_disable(priv->clk); > + > + return !status; > +} > + > +static struct fpga_bridge_ops xlnx_pr_decoupler_br_ops = { > + .enable_set = xlnx_pr_decoupler_enable_set, > + .enable_show = xlnx_pr_decoupler_enable_show, > +}; > + > +static const struct of_device_id xlnx_pr_decoupler_of_match[] = { > + { .compatible = "xlnx,pr-decoupler-1.00", }, > + { .compatible = "xlnx,pr-decoupler", }, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, xlnx_pr_decoupler_of_match); > + > +static int xlnx_pr_decoupler_probe(struct platform_device *pdev) > +{ > + struct xlnx_pr_decoupler_data *priv; > + int err; > + struct resource *res; > + > + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); > + if (!priv) > + return -ENOMEM; > + > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > + priv->io_base = devm_ioremap_resource(&pdev->dev, res); > + if (IS_ERR(priv->io_base)) > + return PTR_ERR(priv->io_base); > + > + priv->clk = devm_clk_get(&pdev->dev, "aclk"); > + if (IS_ERR(priv->clk)) { > + dev_err(&pdev->dev, "input clock not found\n"); > + return PTR_ERR(priv->clk); > + } > + > + err = clk_prepare_enable(priv->clk); > + if (err) { > + dev_err(&pdev->dev, "unable to enable clock\n"); > + return err; > + } > + > + clk_disable(priv->clk); > + > + err = fpga_bridge_register(&pdev->dev, "Xilinx PR Decoupler", > + &xlnx_pr_decoupler_br_ops, priv); > + > + if (err) { > + dev_err(&pdev->dev, "unable to register Xilinx PR Decoupler"); > + clk_unprepare(priv->clk); > + return err; > + } > + > + return 0; > +} > + > +static int xlnx_pr_decoupler_remove(struct platform_device *pdev) > +{ > + struct fpga_bridge *bridge = platform_get_drvdata(pdev); > + struct xlnx_pr_decoupler_data *p = bridge->priv; > + > + fpga_bridge_unregister(&pdev->dev); > + > + clk_unprepare(p->clk); > + > + return 0; > +} > + > +static struct platform_driver xlnx_pr_decoupler_driver = { > + .probe = xlnx_pr_decoupler_probe, > + .remove = xlnx_pr_decoupler_remove, > + .driver = { > + .name = "xlnx_pr_decoupler", > + .of_match_table = of_match_ptr(xlnx_pr_decoupler_of_match), > + }, > +}; > + > +module_platform_driver(xlnx_pr_decoupler_driver); > + > +MODULE_DESCRIPTION("Xilinx Partial Reconfiguration Decoupler"); > +MODULE_AUTHOR("Moritz Fischer <mdf@kernel.org>"); > +MODULE_AUTHOR("Michal Simek <michal.simek@xilinx.com>"); > +MODULE_LICENSE("GPL v2"); > -- > 2.7.4 > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Fri, Mar 17, 2017 at 01:11:12PM -0700, Moritz Fischer wrote: > This adds the binding documentation for the Xilinx LogiCORE PR > Decoupler soft core. > > Signed-off-by: Moritz Fischer <mdf@kernel.org> > Cc: Michal Simek <michal.simek@xilinx.com> > Cc: Sören Brinkmann <soren.brinkmann@xilinx.com> > Cc: linux-kernel@vger.kernel.org > Cc: devicetree@vger.kernel.org > --- > > Changes from v2: > - Added refence to generic fpga-region bindings > - Fixed up reg property in example > - Added fallback to "xlnx,pr-decoupler" without version > > Changes from v1: > - Added clock names & clock to example > - Merged some of the description from Michal's version > > --- > .../bindings/fpga/xilinx-pr-decoupler.txt | 35 ++++++++++++++++++++++ > 1 file changed, 35 insertions(+) > create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt > > diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt > new file mode 100644 > index 0000000..16141bd > --- /dev/null > +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt > @@ -0,0 +1,35 @@ > +Xilinx LogiCORE Partial Reconfig Decoupler Softcore > + > +The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more > +decouplers / fpga bridges. > +The controller can decouple/disable the bridges which prevents signal > +changes from passing through the bridge. The controller can also > +couple / enable the bridges which allows traffic to pass through the > +bridge normally. > + > +The Driver supports only MMIO handling. A PR region can have multiple > +PR Decouples which can bhe handled independently or chaines via decouple/ s/chaines/chains/ > +decouple_status signals. > + > +Required properties: > +- compatible : Should contain "xlnx,pr-decoupler-1.00" > +- regs : base address and size for decoupler module > +- clocks : input clock to IP > +- clock-names : should contain "aclk" > + > +Optional properties: > +- bridge-enable : 0 if driver should disable bridge at startup > + 1 if driver should enable bridge at startup > + Default is to leave bridge in current state. This is common and should move into a common doc. Maybe fpga-region.txt works? > + > +See Documentation/devicetree/bindings/fpga/fpga-region.txt for generic bindings. > + > +Example: > + fpga-bridge@100000450 { > + compatible = "xlnx,pr-decoupler-1.00", > + "xlnx-pr-decoupler"; > + regs = <0x10000045 0x10>; > + clocks = <&clkc 15>; > + clock-names = "aclk"; > + bridge-enable = <0>; > + }; > -- > 2.7.4 > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Fri, Mar 24, 2017 at 09:59:08AM -0500, Rob Herring wrote: > On Fri, Mar 17, 2017 at 01:11:12PM -0700, Moritz Fischer wrote: > > This adds the binding documentation for the Xilinx LogiCORE PR > > Decoupler soft core. > > > > Signed-off-by: Moritz Fischer <mdf@kernel.org> > > Cc: Michal Simek <michal.simek@xilinx.com> > > Cc: Sören Brinkmann <soren.brinkmann@xilinx.com> > > Cc: linux-kernel@vger.kernel.org > > Cc: devicetree@vger.kernel.org > > --- > > > > Changes from v2: > > - Added refence to generic fpga-region bindings > > - Fixed up reg property in example > > - Added fallback to "xlnx,pr-decoupler" without version > > > > Changes from v1: > > - Added clock names & clock to example > > - Merged some of the description from Michal's version > > > > --- > > .../bindings/fpga/xilinx-pr-decoupler.txt | 35 ++++++++++++++++++++++ > > 1 file changed, 35 insertions(+) > > create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt > > > > diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt > > new file mode 100644 > > index 0000000..16141bd > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt > > @@ -0,0 +1,35 @@ > > +Xilinx LogiCORE Partial Reconfig Decoupler Softcore > > + > > +The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more > > +decouplers / fpga bridges. > > +The controller can decouple/disable the bridges which prevents signal > > +changes from passing through the bridge. The controller can also > > +couple / enable the bridges which allows traffic to pass through the > > +bridge normally. > > + > > +The Driver supports only MMIO handling. A PR region can have multiple > > +PR Decouples which can bhe handled independently or chaines via decouple/ > > s/chaines/chains/ Fixed in v4. > > +decouple_status signals. > > + > > +Required properties: > > +- compatible : Should contain "xlnx,pr-decoupler-1.00" > > +- regs : base address and size for decoupler module > > +- clocks : input clock to IP > > +- clock-names : should contain "aclk" > > + > > +Optional properties: > > +- bridge-enable : 0 if driver should disable bridge at startup > > + 1 if driver should enable bridge at startup > > + Default is to leave bridge in current state. > > This is common and should move into a common doc. Maybe fpga-region.txt > works? Ok will add patch for that to v5 series. Thanks for your feedback, Moritz -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Fri, Mar 24, 2017 at 10:23 AM, Moritz Fischer <moritz.fischer.private@gmail.com> wrote: > On Fri, Mar 24, 2017 at 09:59:08AM -0500, Rob Herring wrote: >> On Fri, Mar 17, 2017 at 01:11:12PM -0700, Moritz Fischer wrote: >> > This adds the binding documentation for the Xilinx LogiCORE PR >> > Decoupler soft core. >> > >> > Signed-off-by: Moritz Fischer <mdf@kernel.org> >> > Cc: Michal Simek <michal.simek@xilinx.com> >> > Cc: Sören Brinkmann <soren.brinkmann@xilinx.com> >> > Cc: linux-kernel@vger.kernel.org >> > Cc: devicetree@vger.kernel.org >> > --- >> > >> > Changes from v2: >> > - Added refence to generic fpga-region bindings >> > - Fixed up reg property in example >> > - Added fallback to "xlnx,pr-decoupler" without version >> > >> > Changes from v1: >> > - Added clock names & clock to example >> > - Merged some of the description from Michal's version >> > >> > --- >> > .../bindings/fpga/xilinx-pr-decoupler.txt | 35 ++++++++++++++++++++++ >> > 1 file changed, 35 insertions(+) >> > create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt >> > >> > diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt >> > new file mode 100644 >> > index 0000000..16141bd >> > --- /dev/null >> > +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt >> > @@ -0,0 +1,35 @@ >> > +Xilinx LogiCORE Partial Reconfig Decoupler Softcore >> > + >> > +The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more >> > +decouplers / fpga bridges. >> > +The controller can decouple/disable the bridges which prevents signal >> > +changes from passing through the bridge. The controller can also >> > +couple / enable the bridges which allows traffic to pass through the >> > +bridge normally. >> > + >> > +The Driver supports only MMIO handling. A PR region can have multiple >> > +PR Decouples which can bhe handled independently or chaines via decouple/ >> >> s/chaines/chains/ > > Fixed in v4. > >> > +decouple_status signals. >> > + >> > +Required properties: >> > +- compatible : Should contain "xlnx,pr-decoupler-1.00" >> > +- regs : base address and size for decoupler module >> > +- clocks : input clock to IP >> > +- clock-names : should contain "aclk" >> > + >> > +Optional properties: >> > +- bridge-enable : 0 if driver should disable bridge at startup >> > + 1 if driver should enable bridge at startup >> > + Default is to leave bridge in current state. >> >> This is common and should move into a common doc. Maybe fpga-region.txt >> works? > > Ok will add patch for that to v5 series. Arg, our emails criss-crossed. I've already sent v4 to Greg. I hope we don't need v5 for this one thing. bridge-enable is common for the fpga bridges (altera-fpga2sdram-bridge.txt, altera-freeze-bridge.txt, altera-hps2fpga-bridge.txt, xilinx-pr-decoupler.txt). Probably we need a new patch to move this common bridges binding from all the above to fpga-region.txt or create a new fpga-bridges.txt. At first blush, I prefer the later. Alan > > Thanks for your feedback, > > Moritz -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Fri, Mar 24, 2017 at 12:25:25PM -0500, Alan Tull wrote: > On Fri, Mar 24, 2017 at 10:23 AM, Moritz Fischer > <moritz.fischer.private@gmail.com> wrote: > > On Fri, Mar 24, 2017 at 09:59:08AM -0500, Rob Herring wrote: > >> On Fri, Mar 17, 2017 at 01:11:12PM -0700, Moritz Fischer wrote: > >> > This adds the binding documentation for the Xilinx LogiCORE PR > >> > Decoupler soft core. > >> > > >> > Signed-off-by: Moritz Fischer <mdf@kernel.org> > >> > Cc: Michal Simek <michal.simek@xilinx.com> > >> > Cc: Sören Brinkmann <soren.brinkmann@xilinx.com> > >> > Cc: linux-kernel@vger.kernel.org > >> > Cc: devicetree@vger.kernel.org > >> > --- > >> > > >> > Changes from v2: > >> > - Added refence to generic fpga-region bindings > >> > - Fixed up reg property in example > >> > - Added fallback to "xlnx,pr-decoupler" without version > >> > > >> > Changes from v1: > >> > - Added clock names & clock to example > >> > - Merged some of the description from Michal's version > >> > > >> > --- > >> > .../bindings/fpga/xilinx-pr-decoupler.txt | 35 ++++++++++++++++++++++ > >> > 1 file changed, 35 insertions(+) > >> > create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt > >> > > >> > diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt > >> > new file mode 100644 > >> > index 0000000..16141bd > >> > --- /dev/null > >> > +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt > >> > @@ -0,0 +1,35 @@ > >> > +Xilinx LogiCORE Partial Reconfig Decoupler Softcore > >> > + > >> > +The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more > >> > +decouplers / fpga bridges. > >> > +The controller can decouple/disable the bridges which prevents signal > >> > +changes from passing through the bridge. The controller can also > >> > +couple / enable the bridges which allows traffic to pass through the > >> > +bridge normally. > >> > + > >> > +The Driver supports only MMIO handling. A PR region can have multiple > >> > +PR Decouples which can bhe handled independently or chaines via decouple/ > >> > >> s/chaines/chains/ > > > > Fixed in v4. > > > >> > +decouple_status signals. > >> > + > >> > +Required properties: > >> > +- compatible : Should contain "xlnx,pr-decoupler-1.00" > >> > +- regs : base address and size for decoupler module > >> > +- clocks : input clock to IP > >> > +- clock-names : should contain "aclk" > >> > + > >> > +Optional properties: > >> > +- bridge-enable : 0 if driver should disable bridge at startup > >> > + 1 if driver should enable bridge at startup > >> > + Default is to leave bridge in current state. > >> > >> This is common and should move into a common doc. Maybe fpga-region.txt > >> works? > > > > Ok will add patch for that to v5 series. > > Arg, our emails criss-crossed. I've already sent v4 to Greg. I hope > we don't need v5 for this one thing. bridge-enable is common for the > fpga bridges (altera-fpga2sdram-bridge.txt, altera-freeze-bridge.txt, > altera-hps2fpga-bridge.txt, xilinx-pr-decoupler.txt). Probably we > need a new patch to move this common bridges binding from all the > above to fpga-region.txt or create a new fpga-bridges.txt. At first > blush, I prefer the later. Yeah, I'll just send a follow-up patch, it's not that it breaks anything the way it is. - Moritz
diff --git a/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt new file mode 100644 index 0000000..16141bd --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt @@ -0,0 +1,35 @@ +Xilinx LogiCORE Partial Reconfig Decoupler Softcore + +The Xilinx LogiCORE Partial Reconfig Decoupler manages one or more +decouplers / fpga bridges. +The controller can decouple/disable the bridges which prevents signal +changes from passing through the bridge. The controller can also +couple / enable the bridges which allows traffic to pass through the +bridge normally. + +The Driver supports only MMIO handling. A PR region can have multiple +PR Decouples which can bhe handled independently or chaines via decouple/ +decouple_status signals. + +Required properties: +- compatible : Should contain "xlnx,pr-decoupler-1.00" +- regs : base address and size for decoupler module +- clocks : input clock to IP +- clock-names : should contain "aclk" + +Optional properties: +- bridge-enable : 0 if driver should disable bridge at startup + 1 if driver should enable bridge at startup + Default is to leave bridge in current state. + +See Documentation/devicetree/bindings/fpga/fpga-region.txt for generic bindings. + +Example: + fpga-bridge@100000450 { + compatible = "xlnx,pr-decoupler-1.00", + "xlnx-pr-decoupler"; + regs = <0x10000045 0x10>; + clocks = <&clkc 15>; + clock-names = "aclk"; + bridge-enable = <0>; + };
This adds the binding documentation for the Xilinx LogiCORE PR Decoupler soft core. Signed-off-by: Moritz Fischer <mdf@kernel.org> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Sören Brinkmann <soren.brinkmann@xilinx.com> Cc: linux-kernel@vger.kernel.org Cc: devicetree@vger.kernel.org --- Changes from v2: - Added refence to generic fpga-region bindings - Fixed up reg property in example - Added fallback to "xlnx,pr-decoupler" without version Changes from v1: - Added clock names & clock to example - Merged some of the description from Michal's version --- .../bindings/fpga/xilinx-pr-decoupler.txt | 35 ++++++++++++++++++++++ 1 file changed, 35 insertions(+) create mode 100644 Documentation/devicetree/bindings/fpga/xilinx-pr-decoupler.txt