Message ID | 20170301070447.20255-2-wens@csie.org |
---|---|
State | Superseded |
Delegated to: | Jagannadha Sutradharudu Teki |
Headers | show |
Hi Chen-Yu On Wed, Mar 01, 2017 at 03:04:36PM +0800, Chen-Yu Tsai wrote: > The R40 is the successor to the A20. It is a hybrid of the A20, A33 > and the H3. > > The R40's PIO controller is compatible with the A20, > Reuse the A20 UART and I2C muxing code by adding the R40's macro. > > The display pipeline is the newer DE 2.0 variant. > Block enabling video on R40 for now. > > Signed-off-by: Chen-Yu Tsai <wens@csie.org> > --- > arch/arm/mach-sunxi/board.c | 10 +++++++--- > arch/arm/mach-sunxi/cpu_info.c | 2 ++ > board/sunxi/Kconfig | 9 +++++++-- > board/sunxi/board.c | 19 ++++++++++++++----- > 4 files changed, 30 insertions(+), 10 deletions(-) > > diff --git a/arch/arm/mach-sunxi/board.c b/arch/arm/mach-sunxi/board.c > index 5e03d039433a..5a74c9717d84 100644 > --- a/arch/arm/mach-sunxi/board.c > +++ b/arch/arm/mach-sunxi/board.c > @@ -69,12 +69,14 @@ struct mm_region *mem_map = sunxi_mem_map; > static int gpio_init(void) > { > #if CONFIG_CONS_INDEX == 1 && defined(CONFIG_UART0_PORT_F) > -#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I) > +#if defined(CONFIG_MACH_SUN4I) || \ > + defined(CONFIG_MACH_SUN7I) || \ > + defined(CONFIG_MACH_SUN8I_R40) > /* disable GPB22,23 as uart0 tx,rx to avoid conflict */ > sunxi_gpio_set_cfgpin(SUNXI_GPB(22), SUNXI_GPIO_INPUT); > sunxi_gpio_set_cfgpin(SUNXI_GPB(23), SUNXI_GPIO_INPUT); > #endif > -#if defined(CONFIG_MACH_SUN8I) > +#if defined(CONFIG_MACH_SUN8I) && !defined(CONFIG_MACH_SUN8I_R40) > sunxi_gpio_set_cfgpin(SUNXI_GPF(2), SUN8I_GPF_UART0); > sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUN8I_GPF_UART0); > #else > @@ -82,7 +84,9 @@ static int gpio_init(void) > sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUNXI_GPF_UART0); > #endif > sunxi_gpio_set_pull(SUNXI_GPF(4), 1); > -#elif CONFIG_CONS_INDEX == 1 && (defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I)) > +#elif CONFIG_CONS_INDEX == 1 && (defined(CONFIG_MACH_SUN4I) || \ > + defined(CONFIG_MACH_SUN7I) || \ > + defined(CONFIG_MACH_SUN8I_R40)) > sunxi_gpio_set_cfgpin(SUNXI_GPB(22), SUN4I_GPB_UART0); > sunxi_gpio_set_cfgpin(SUNXI_GPB(23), SUN4I_GPB_UART0); > sunxi_gpio_set_pull(SUNXI_GPB(23), SUNXI_GPIO_PULL_UP); > diff --git a/arch/arm/mach-sunxi/cpu_info.c b/arch/arm/mach-sunxi/cpu_info.c > index 85633ccec216..7851de299ab5 100644 > --- a/arch/arm/mach-sunxi/cpu_info.c > +++ b/arch/arm/mach-sunxi/cpu_info.c > @@ -87,6 +87,8 @@ int print_cpuinfo(void) > printf("CPU: Allwinner A83T (SUN8I %04x)\n", sunxi_get_sram_id()); > #elif defined CONFIG_MACH_SUN8I_H3 > printf("CPU: Allwinner H3 (SUN8I %04x)\n", sunxi_get_sram_id()); > +#elif defined CONFIG_MACH_SUN8I_R40 > + printf("CPU: Allwinner R40 (SUN8I %04x)\n", sunxi_get_sram_id()); > #elif defined CONFIG_MACH_SUN9I > puts("CPU: Allwinner A80 (SUN9I)\n"); > #elif defined CONFIG_MACH_SUN50I > diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig > index 3e0e2624737e..8e8b9cd0d5fd 100644 > --- a/board/sunxi/Kconfig > +++ b/board/sunxi/Kconfig > @@ -132,6 +132,11 @@ config MACH_SUN8I_H3 > select MACH_SUNXI_H3_H5 > select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT > > +config MACH_SUN8I_R40 > + bool "sun8i (Allwinner R40)" > + select CPU_V7 > + select SUNXI_GEN_SUN6I > + > config MACH_SUN9I > bool "sun9i (Allwinner A80)" > select CPU_V7 > @@ -157,7 +162,7 @@ endchoice > # The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 || A33" > config MACH_SUN8I > bool > - default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUNXI_H3_H5 || MACH_SUN8I_A83T > + default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUNXI_H3_H5 || MACH_SUN8I_A83T || MACH_SUN8I_R40 You should really wrap that line too (and CONFIG_VIDEO below). Once done, you have my Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Thanks! Maxime
On Wed, Mar 1, 2017 at 6:55 PM, Maxime Ripard <maxime.ripard@free-electrons.com> wrote: > Hi Chen-Yu > > On Wed, Mar 01, 2017 at 03:04:36PM +0800, Chen-Yu Tsai wrote: >> The R40 is the successor to the A20. It is a hybrid of the A20, A33 >> and the H3. >> >> The R40's PIO controller is compatible with the A20, >> Reuse the A20 UART and I2C muxing code by adding the R40's macro. >> >> The display pipeline is the newer DE 2.0 variant. >> Block enabling video on R40 for now. >> >> Signed-off-by: Chen-Yu Tsai <wens@csie.org> >> --- >> arch/arm/mach-sunxi/board.c | 10 +++++++--- >> arch/arm/mach-sunxi/cpu_info.c | 2 ++ >> board/sunxi/Kconfig | 9 +++++++-- >> board/sunxi/board.c | 19 ++++++++++++++----- >> 4 files changed, 30 insertions(+), 10 deletions(-) >> >> diff --git a/arch/arm/mach-sunxi/board.c b/arch/arm/mach-sunxi/board.c >> index 5e03d039433a..5a74c9717d84 100644 >> --- a/arch/arm/mach-sunxi/board.c >> +++ b/arch/arm/mach-sunxi/board.c >> @@ -69,12 +69,14 @@ struct mm_region *mem_map = sunxi_mem_map; >> static int gpio_init(void) >> { >> #if CONFIG_CONS_INDEX == 1 && defined(CONFIG_UART0_PORT_F) >> -#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I) >> +#if defined(CONFIG_MACH_SUN4I) || \ >> + defined(CONFIG_MACH_SUN7I) || \ >> + defined(CONFIG_MACH_SUN8I_R40) >> /* disable GPB22,23 as uart0 tx,rx to avoid conflict */ >> sunxi_gpio_set_cfgpin(SUNXI_GPB(22), SUNXI_GPIO_INPUT); >> sunxi_gpio_set_cfgpin(SUNXI_GPB(23), SUNXI_GPIO_INPUT); >> #endif >> -#if defined(CONFIG_MACH_SUN8I) >> +#if defined(CONFIG_MACH_SUN8I) && !defined(CONFIG_MACH_SUN8I_R40) >> sunxi_gpio_set_cfgpin(SUNXI_GPF(2), SUN8I_GPF_UART0); >> sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUN8I_GPF_UART0); >> #else >> @@ -82,7 +84,9 @@ static int gpio_init(void) >> sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUNXI_GPF_UART0); >> #endif >> sunxi_gpio_set_pull(SUNXI_GPF(4), 1); >> -#elif CONFIG_CONS_INDEX == 1 && (defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I)) >> +#elif CONFIG_CONS_INDEX == 1 && (defined(CONFIG_MACH_SUN4I) || \ >> + defined(CONFIG_MACH_SUN7I) || \ >> + defined(CONFIG_MACH_SUN8I_R40)) >> sunxi_gpio_set_cfgpin(SUNXI_GPB(22), SUN4I_GPB_UART0); >> sunxi_gpio_set_cfgpin(SUNXI_GPB(23), SUN4I_GPB_UART0); >> sunxi_gpio_set_pull(SUNXI_GPB(23), SUNXI_GPIO_PULL_UP); >> diff --git a/arch/arm/mach-sunxi/cpu_info.c b/arch/arm/mach-sunxi/cpu_info.c >> index 85633ccec216..7851de299ab5 100644 >> --- a/arch/arm/mach-sunxi/cpu_info.c >> +++ b/arch/arm/mach-sunxi/cpu_info.c >> @@ -87,6 +87,8 @@ int print_cpuinfo(void) >> printf("CPU: Allwinner A83T (SUN8I %04x)\n", sunxi_get_sram_id()); >> #elif defined CONFIG_MACH_SUN8I_H3 >> printf("CPU: Allwinner H3 (SUN8I %04x)\n", sunxi_get_sram_id()); >> +#elif defined CONFIG_MACH_SUN8I_R40 >> + printf("CPU: Allwinner R40 (SUN8I %04x)\n", sunxi_get_sram_id()); >> #elif defined CONFIG_MACH_SUN9I >> puts("CPU: Allwinner A80 (SUN9I)\n"); >> #elif defined CONFIG_MACH_SUN50I >> diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig >> index 3e0e2624737e..8e8b9cd0d5fd 100644 >> --- a/board/sunxi/Kconfig >> +++ b/board/sunxi/Kconfig >> @@ -132,6 +132,11 @@ config MACH_SUN8I_H3 >> select MACH_SUNXI_H3_H5 >> select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT >> >> +config MACH_SUN8I_R40 >> + bool "sun8i (Allwinner R40)" >> + select CPU_V7 >> + select SUNXI_GEN_SUN6I >> + >> config MACH_SUN9I >> bool "sun9i (Allwinner A80)" >> select CPU_V7 >> @@ -157,7 +162,7 @@ endchoice >> # The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 || A33" >> config MACH_SUN8I >> bool >> - default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUNXI_H3_H5 || MACH_SUN8I_A83T >> + default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUNXI_H3_H5 || MACH_SUN8I_A83T || MACH_SUN8I_R40 > > You should really wrap that line too (and CONFIG_VIDEO below). Kconfig doesn't seem to like line wrapping. I can split both into 1 symbol per line though. Would that be taking it to far? ChenYu > Once done, you have my > Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> > > Thanks! > Maxime > -- > Maxime Ripard, Free Electrons > Embedded Linux and Kernel engineering > http://free-electrons.com
1;4601;0c On Wed, Mar 01, 2017 at 08:10:55PM +0800, Chen-Yu Tsai wrote: > On Wed, Mar 1, 2017 at 6:55 PM, Maxime Ripard > <maxime.ripard@free-electrons.com> wrote: > > Hi Chen-Yu > > > > On Wed, Mar 01, 2017 at 03:04:36PM +0800, Chen-Yu Tsai wrote: > >> The R40 is the successor to the A20. It is a hybrid of the A20, A33 > >> and the H3. > >> > >> The R40's PIO controller is compatible with the A20, > >> Reuse the A20 UART and I2C muxing code by adding the R40's macro. > >> > >> The display pipeline is the newer DE 2.0 variant. > >> Block enabling video on R40 for now. > >> > >> Signed-off-by: Chen-Yu Tsai <wens@csie.org> > >> --- > >> arch/arm/mach-sunxi/board.c | 10 +++++++--- > >> arch/arm/mach-sunxi/cpu_info.c | 2 ++ > >> board/sunxi/Kconfig | 9 +++++++-- > >> board/sunxi/board.c | 19 ++++++++++++++----- > >> 4 files changed, 30 insertions(+), 10 deletions(-) > >> > >> diff --git a/arch/arm/mach-sunxi/board.c b/arch/arm/mach-sunxi/board.c > >> index 5e03d039433a..5a74c9717d84 100644 > >> --- a/arch/arm/mach-sunxi/board.c > >> +++ b/arch/arm/mach-sunxi/board.c > >> @@ -69,12 +69,14 @@ struct mm_region *mem_map = sunxi_mem_map; > >> static int gpio_init(void) > >> { > >> #if CONFIG_CONS_INDEX == 1 && defined(CONFIG_UART0_PORT_F) > >> -#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I) > >> +#if defined(CONFIG_MACH_SUN4I) || \ > >> + defined(CONFIG_MACH_SUN7I) || \ > >> + defined(CONFIG_MACH_SUN8I_R40) > >> /* disable GPB22,23 as uart0 tx,rx to avoid conflict */ > >> sunxi_gpio_set_cfgpin(SUNXI_GPB(22), SUNXI_GPIO_INPUT); > >> sunxi_gpio_set_cfgpin(SUNXI_GPB(23), SUNXI_GPIO_INPUT); > >> #endif > >> -#if defined(CONFIG_MACH_SUN8I) > >> +#if defined(CONFIG_MACH_SUN8I) && !defined(CONFIG_MACH_SUN8I_R40) > >> sunxi_gpio_set_cfgpin(SUNXI_GPF(2), SUN8I_GPF_UART0); > >> sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUN8I_GPF_UART0); > >> #else > >> @@ -82,7 +84,9 @@ static int gpio_init(void) > >> sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUNXI_GPF_UART0); > >> #endif > >> sunxi_gpio_set_pull(SUNXI_GPF(4), 1); > >> -#elif CONFIG_CONS_INDEX == 1 && (defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I)) > >> +#elif CONFIG_CONS_INDEX == 1 && (defined(CONFIG_MACH_SUN4I) || \ > >> + defined(CONFIG_MACH_SUN7I) || \ > >> + defined(CONFIG_MACH_SUN8I_R40)) > >> sunxi_gpio_set_cfgpin(SUNXI_GPB(22), SUN4I_GPB_UART0); > >> sunxi_gpio_set_cfgpin(SUNXI_GPB(23), SUN4I_GPB_UART0); > >> sunxi_gpio_set_pull(SUNXI_GPB(23), SUNXI_GPIO_PULL_UP); > >> diff --git a/arch/arm/mach-sunxi/cpu_info.c b/arch/arm/mach-sunxi/cpu_info.c > >> index 85633ccec216..7851de299ab5 100644 > >> --- a/arch/arm/mach-sunxi/cpu_info.c > >> +++ b/arch/arm/mach-sunxi/cpu_info.c > >> @@ -87,6 +87,8 @@ int print_cpuinfo(void) > >> printf("CPU: Allwinner A83T (SUN8I %04x)\n", sunxi_get_sram_id()); > >> #elif defined CONFIG_MACH_SUN8I_H3 > >> printf("CPU: Allwinner H3 (SUN8I %04x)\n", sunxi_get_sram_id()); > >> +#elif defined CONFIG_MACH_SUN8I_R40 > >> + printf("CPU: Allwinner R40 (SUN8I %04x)\n", sunxi_get_sram_id()); > >> #elif defined CONFIG_MACH_SUN9I > >> puts("CPU: Allwinner A80 (SUN9I)\n"); > >> #elif defined CONFIG_MACH_SUN50I > >> diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig > >> index 3e0e2624737e..8e8b9cd0d5fd 100644 > >> --- a/board/sunxi/Kconfig > >> +++ b/board/sunxi/Kconfig > >> @@ -132,6 +132,11 @@ config MACH_SUN8I_H3 > >> select MACH_SUNXI_H3_H5 > >> select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT > >> > >> +config MACH_SUN8I_R40 > >> + bool "sun8i (Allwinner R40)" > >> + select CPU_V7 > >> + select SUNXI_GEN_SUN6I > >> + > >> config MACH_SUN9I > >> bool "sun9i (Allwinner A80)" > >> select CPU_V7 > >> @@ -157,7 +162,7 @@ endchoice > >> # The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 || A33" > >> config MACH_SUN8I > >> bool > >> - default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUNXI_H3_H5 || MACH_SUN8I_A83T > >> + default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUNXI_H3_H5 || MACH_SUN8I_A83T || MACH_SUN8I_R40 > > > > You should really wrap that line too (and CONFIG_VIDEO below). > > Kconfig doesn't seem to like line wrapping. I can split both into > 1 symbol per line though. Would that be taking it to far? Something like: default y if MACH_SUN8I_A23 default y if MACH_SUN8I_A33 ? I didn't know it was possible.. But if it works, yes, please that will even be easier to review / extend. Thanks! Maxime
01.03.2017, 22:57, "Maxime Ripard" <maxime.ripard@free-electrons.com>: > 1;4601;0c > On Wed, Mar 01, 2017 at 08:10:55PM +0800, Chen-Yu Tsai wrote: >> On Wed, Mar 1, 2017 at 6:55 PM, Maxime Ripard >> <maxime.ripard@free-electrons.com> wrote: >> > Hi Chen-Yu >> > >> > On Wed, Mar 01, 2017 at 03:04:36PM +0800, Chen-Yu Tsai wrote: >> >> The R40 is the successor to the A20. It is a hybrid of the A20, A33 >> >> and the H3. >> >> >> >> The R40's PIO controller is compatible with the A20, >> >> Reuse the A20 UART and I2C muxing code by adding the R40's macro. >> >> >> >> The display pipeline is the newer DE 2.0 variant. >> >> Block enabling video on R40 for now. >> >> >> >> Signed-off-by: Chen-Yu Tsai <wens@csie.org> >> >> --- >> >> arch/arm/mach-sunxi/board.c | 10 +++++++--- >> >> arch/arm/mach-sunxi/cpu_info.c | 2 ++ >> >> board/sunxi/Kconfig | 9 +++++++-- >> >> board/sunxi/board.c | 19 ++++++++++++++----- >> >> 4 files changed, 30 insertions(+), 10 deletions(-) >> >> >> >> diff --git a/arch/arm/mach-sunxi/board.c b/arch/arm/mach-sunxi/board.c >> >> index 5e03d039433a..5a74c9717d84 100644 >> >> --- a/arch/arm/mach-sunxi/board.c >> >> +++ b/arch/arm/mach-sunxi/board.c >> >> @@ -69,12 +69,14 @@ struct mm_region *mem_map = sunxi_mem_map; >> >> static int gpio_init(void) >> >> { >> >> #if CONFIG_CONS_INDEX == 1 && defined(CONFIG_UART0_PORT_F) >> >> -#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I) >> >> +#if defined(CONFIG_MACH_SUN4I) || \ >> >> + defined(CONFIG_MACH_SUN7I) || \ >> >> + defined(CONFIG_MACH_SUN8I_R40) >> >> /* disable GPB22,23 as uart0 tx,rx to avoid conflict */ >> >> sunxi_gpio_set_cfgpin(SUNXI_GPB(22), SUNXI_GPIO_INPUT); >> >> sunxi_gpio_set_cfgpin(SUNXI_GPB(23), SUNXI_GPIO_INPUT); >> >> #endif >> >> -#if defined(CONFIG_MACH_SUN8I) >> >> +#if defined(CONFIG_MACH_SUN8I) && !defined(CONFIG_MACH_SUN8I_R40) >> >> sunxi_gpio_set_cfgpin(SUNXI_GPF(2), SUN8I_GPF_UART0); >> >> sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUN8I_GPF_UART0); >> >> #else >> >> @@ -82,7 +84,9 @@ static int gpio_init(void) >> >> sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUNXI_GPF_UART0); >> >> #endif >> >> sunxi_gpio_set_pull(SUNXI_GPF(4), 1); >> >> -#elif CONFIG_CONS_INDEX == 1 && (defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I)) >> >> +#elif CONFIG_CONS_INDEX == 1 && (defined(CONFIG_MACH_SUN4I) || \ >> >> + defined(CONFIG_MACH_SUN7I) || \ >> >> + defined(CONFIG_MACH_SUN8I_R40)) >> >> sunxi_gpio_set_cfgpin(SUNXI_GPB(22), SUN4I_GPB_UART0); >> >> sunxi_gpio_set_cfgpin(SUNXI_GPB(23), SUN4I_GPB_UART0); >> >> sunxi_gpio_set_pull(SUNXI_GPB(23), SUNXI_GPIO_PULL_UP); >> >> diff --git a/arch/arm/mach-sunxi/cpu_info.c b/arch/arm/mach-sunxi/cpu_info.c >> >> index 85633ccec216..7851de299ab5 100644 >> >> --- a/arch/arm/mach-sunxi/cpu_info.c >> >> +++ b/arch/arm/mach-sunxi/cpu_info.c >> >> @@ -87,6 +87,8 @@ int print_cpuinfo(void) >> >> printf("CPU: Allwinner A83T (SUN8I %04x)\n", sunxi_get_sram_id()); >> >> #elif defined CONFIG_MACH_SUN8I_H3 >> >> printf("CPU: Allwinner H3 (SUN8I %04x)\n", sunxi_get_sram_id()); >> >> +#elif defined CONFIG_MACH_SUN8I_R40 >> >> + printf("CPU: Allwinner R40 (SUN8I %04x)\n", sunxi_get_sram_id()); >> >> #elif defined CONFIG_MACH_SUN9I >> >> puts("CPU: Allwinner A80 (SUN9I)\n"); >> >> #elif defined CONFIG_MACH_SUN50I >> >> diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig >> >> index 3e0e2624737e..8e8b9cd0d5fd 100644 >> >> --- a/board/sunxi/Kconfig >> >> +++ b/board/sunxi/Kconfig >> >> @@ -132,6 +132,11 @@ config MACH_SUN8I_H3 >> >> select MACH_SUNXI_H3_H5 >> >> select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT >> >> >> >> +config MACH_SUN8I_R40 >> >> + bool "sun8i (Allwinner R40)" >> >> + select CPU_V7 >> >> + select SUNXI_GEN_SUN6I >> >> + >> >> config MACH_SUN9I >> >> bool "sun9i (Allwinner A80)" >> >> select CPU_V7 >> >> @@ -157,7 +162,7 @@ endchoice >> >> # The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 || A33" >> >> config MACH_SUN8I >> >> bool >> >> - default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUNXI_H3_H5 || MACH_SUN8I_A83T >> >> + default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUNXI_H3_H5 || MACH_SUN8I_A83T || MACH_SUN8I_R40 >> > >> > You should really wrap that line too (and CONFIG_VIDEO below). >> >> Kconfig doesn't seem to like line wrapping. I can split both into >> 1 symbol per line though. Would that be taking it to far? Kconfig can accept line wrapping. But you need \. > > Something like: > > default y if MACH_SUN8I_A23 > default y if MACH_SUN8I_A33 > > ? > > I didn't know it was possible.. But if it works, yes, please that will > even be easier to review / extend. > > Thanks! > Maxime > > -- > Maxime Ripard, Free Electrons > Embedded Linux and Kernel engineering > http://free-electrons.com > > -- > You received this message because you are subscribed to the Google Groups "linux-sunxi" group. > To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@googlegroups.com. > For more options, visit https://groups.google.com/d/optout.
diff --git a/arch/arm/mach-sunxi/board.c b/arch/arm/mach-sunxi/board.c index 5e03d039433a..5a74c9717d84 100644 --- a/arch/arm/mach-sunxi/board.c +++ b/arch/arm/mach-sunxi/board.c @@ -69,12 +69,14 @@ struct mm_region *mem_map = sunxi_mem_map; static int gpio_init(void) { #if CONFIG_CONS_INDEX == 1 && defined(CONFIG_UART0_PORT_F) -#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I) +#if defined(CONFIG_MACH_SUN4I) || \ + defined(CONFIG_MACH_SUN7I) || \ + defined(CONFIG_MACH_SUN8I_R40) /* disable GPB22,23 as uart0 tx,rx to avoid conflict */ sunxi_gpio_set_cfgpin(SUNXI_GPB(22), SUNXI_GPIO_INPUT); sunxi_gpio_set_cfgpin(SUNXI_GPB(23), SUNXI_GPIO_INPUT); #endif -#if defined(CONFIG_MACH_SUN8I) +#if defined(CONFIG_MACH_SUN8I) && !defined(CONFIG_MACH_SUN8I_R40) sunxi_gpio_set_cfgpin(SUNXI_GPF(2), SUN8I_GPF_UART0); sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUN8I_GPF_UART0); #else @@ -82,7 +84,9 @@ static int gpio_init(void) sunxi_gpio_set_cfgpin(SUNXI_GPF(4), SUNXI_GPF_UART0); #endif sunxi_gpio_set_pull(SUNXI_GPF(4), 1); -#elif CONFIG_CONS_INDEX == 1 && (defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I)) +#elif CONFIG_CONS_INDEX == 1 && (defined(CONFIG_MACH_SUN4I) || \ + defined(CONFIG_MACH_SUN7I) || \ + defined(CONFIG_MACH_SUN8I_R40)) sunxi_gpio_set_cfgpin(SUNXI_GPB(22), SUN4I_GPB_UART0); sunxi_gpio_set_cfgpin(SUNXI_GPB(23), SUN4I_GPB_UART0); sunxi_gpio_set_pull(SUNXI_GPB(23), SUNXI_GPIO_PULL_UP); diff --git a/arch/arm/mach-sunxi/cpu_info.c b/arch/arm/mach-sunxi/cpu_info.c index 85633ccec216..7851de299ab5 100644 --- a/arch/arm/mach-sunxi/cpu_info.c +++ b/arch/arm/mach-sunxi/cpu_info.c @@ -87,6 +87,8 @@ int print_cpuinfo(void) printf("CPU: Allwinner A83T (SUN8I %04x)\n", sunxi_get_sram_id()); #elif defined CONFIG_MACH_SUN8I_H3 printf("CPU: Allwinner H3 (SUN8I %04x)\n", sunxi_get_sram_id()); +#elif defined CONFIG_MACH_SUN8I_R40 + printf("CPU: Allwinner R40 (SUN8I %04x)\n", sunxi_get_sram_id()); #elif defined CONFIG_MACH_SUN9I puts("CPU: Allwinner A80 (SUN9I)\n"); #elif defined CONFIG_MACH_SUN50I diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig index 3e0e2624737e..8e8b9cd0d5fd 100644 --- a/board/sunxi/Kconfig +++ b/board/sunxi/Kconfig @@ -132,6 +132,11 @@ config MACH_SUN8I_H3 select MACH_SUNXI_H3_H5 select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT +config MACH_SUN8I_R40 + bool "sun8i (Allwinner R40)" + select CPU_V7 + select SUNXI_GEN_SUN6I + config MACH_SUN9I bool "sun9i (Allwinner A80)" select CPU_V7 @@ -157,7 +162,7 @@ endchoice # The sun8i SoCs share a lot, this helps to avoid a lot of "if A23 || A33" config MACH_SUN8I bool - default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUNXI_H3_H5 || MACH_SUN8I_A83T + default y if MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUNXI_H3_H5 || MACH_SUN8I_A83T || MACH_SUN8I_R40 config RESERVE_ALLWINNER_BOOT0_HEADER bool "reserve space for Allwinner boot0 header" @@ -510,7 +515,7 @@ config AXP_GPIO config VIDEO bool "Enable graphical uboot console on HDMI, LCD or VGA" - depends on !MACH_SUN8I_A83T && !MACH_SUNXI_H3_H5 && !MACH_SUN9I && !MACH_SUN50I + depends on !MACH_SUN8I_A83T && !MACH_SUNXI_H3_H5 && !MACH_SUN8I_R40 && !MACH_SUN9I && !MACH_SUN50I default y ---help--- Say Y here to add support for using a cfb console on the HDMI, LCD diff --git a/board/sunxi/board.c b/board/sunxi/board.c index b9660128e5e7..495cb591a9fb 100644 --- a/board/sunxi/board.c +++ b/board/sunxi/board.c @@ -394,7 +394,10 @@ int board_mmc_init(bd_t *bis) void i2c_init_board(void) { #ifdef CONFIG_I2C0_ENABLE -#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN5I) || defined(CONFIG_MACH_SUN7I) +#if defined(CONFIG_MACH_SUN4I) || \ + defined(CONFIG_MACH_SUN5I) || \ + defined(CONFIG_MACH_SUN7I) || \ + defined(CONFIG_MACH_SUN8I_R40) sunxi_gpio_set_cfgpin(SUNXI_GPB(0), SUN4I_GPB_TWI0); sunxi_gpio_set_cfgpin(SUNXI_GPB(1), SUN4I_GPB_TWI0); clock_twi_onoff(0, 1); @@ -410,7 +413,9 @@ void i2c_init_board(void) #endif #ifdef CONFIG_I2C1_ENABLE -#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I) +#if defined(CONFIG_MACH_SUN4I) || \ + defined(CONFIG_MACH_SUN7I) || \ + defined(CONFIG_MACH_SUN8I_R40) sunxi_gpio_set_cfgpin(SUNXI_GPB(18), SUN4I_GPB_TWI1); sunxi_gpio_set_cfgpin(SUNXI_GPB(19), SUN4I_GPB_TWI1); clock_twi_onoff(1, 1); @@ -430,7 +435,9 @@ void i2c_init_board(void) #endif #ifdef CONFIG_I2C2_ENABLE -#if defined(CONFIG_MACH_SUN4I) || defined(CONFIG_MACH_SUN7I) +#if defined(CONFIG_MACH_SUN4I) || \ + defined(CONFIG_MACH_SUN7I) || \ + defined(CONFIG_MACH_SUN8I_R40) sunxi_gpio_set_cfgpin(SUNXI_GPB(20), SUN4I_GPB_TWI2); sunxi_gpio_set_cfgpin(SUNXI_GPB(21), SUN4I_GPB_TWI2); clock_twi_onoff(2, 1); @@ -454,7 +461,8 @@ void i2c_init_board(void) sunxi_gpio_set_cfgpin(SUNXI_GPG(10), SUN6I_GPG_TWI3); sunxi_gpio_set_cfgpin(SUNXI_GPG(11), SUN6I_GPG_TWI3); clock_twi_onoff(3, 1); -#elif defined(CONFIG_MACH_SUN7I) +#elif defined(CONFIG_MACH_SUN7I) || \ + defined(CONFIG_MACH_SUN8I_R40) sunxi_gpio_set_cfgpin(SUNXI_GPI(0), SUN7I_GPI_TWI3); sunxi_gpio_set_cfgpin(SUNXI_GPI(1), SUN7I_GPI_TWI3); clock_twi_onoff(3, 1); @@ -462,7 +470,8 @@ void i2c_init_board(void) #endif #ifdef CONFIG_I2C4_ENABLE -#if defined(CONFIG_MACH_SUN7I) +#if defined(CONFIG_MACH_SUN7I) || \ + defined(CONFIG_MACH_SUN8I_R40) sunxi_gpio_set_cfgpin(SUNXI_GPI(2), SUN7I_GPI_TWI4); sunxi_gpio_set_cfgpin(SUNXI_GPI(3), SUN7I_GPI_TWI4); clock_twi_onoff(4, 1);
The R40 is the successor to the A20. It is a hybrid of the A20, A33 and the H3. The R40's PIO controller is compatible with the A20, Reuse the A20 UART and I2C muxing code by adding the R40's macro. The display pipeline is the newer DE 2.0 variant. Block enabling video on R40 for now. Signed-off-by: Chen-Yu Tsai <wens@csie.org> --- arch/arm/mach-sunxi/board.c | 10 +++++++--- arch/arm/mach-sunxi/cpu_info.c | 2 ++ board/sunxi/Kconfig | 9 +++++++-- board/sunxi/board.c | 19 ++++++++++++++----- 4 files changed, 30 insertions(+), 10 deletions(-)