Message ID | 1487322752-31896-1-git-send-email-preid@electromag.com.au |
---|---|
State | New |
Headers | show |
On Fri, Feb 17, 2017 at 11:12 AM, Phil Reid <preid@electromag.com.au> wrote: > When a threaded irq handler is chained attached to one of the gpio > pins when configure for level irq the altera_gpio_irq_leveL_high_handler > does not mask the interrupt while being handled by the chained irq. > This resulting in the threaded irq not getting enough cycles to complete > quickly enough before the irq was disabled as faulty. > It looks like handle_level_irq should be used in this situation > instead of handle_simple_irq. > @@ -310,7 +310,8 @@ static int altera_gpio_probe(struct platform_device *pdev) > altera_gc->interrupt_trigger = reg; > > ret = gpiochip_irqchip_add(&altera_gc->mmchip.gc, &altera_irq_chip, 0, > - handle_simple_irq, IRQ_TYPE_NONE); > + altera_gc->interrupt_trigger == IRQ_TYPE_LEVEL_HIGH ? > + handle_level_irq : handle_simple_irq, IRQ_TYPE_NONE); AFAIK, handle_bad_irq() should be used here.
On 17/02/2017 17:23, Andy Shevchenko wrote: > On Fri, Feb 17, 2017 at 11:12 AM, Phil Reid <preid@electromag.com.au> wrote: >> When a threaded irq handler is chained attached to one of the gpio >> pins when configure for level irq the altera_gpio_irq_leveL_high_handler >> does not mask the interrupt while being handled by the chained irq. >> This resulting in the threaded irq not getting enough cycles to complete >> quickly enough before the irq was disabled as faulty. >> It looks like handle_level_irq should be used in this situation >> instead of handle_simple_irq. > >> @@ -310,7 +310,8 @@ static int altera_gpio_probe(struct platform_device *pdev) >> altera_gc->interrupt_trigger = reg; >> >> ret = gpiochip_irqchip_add(&altera_gc->mmchip.gc, &altera_irq_chip, 0, >> - handle_simple_irq, IRQ_TYPE_NONE); >> + altera_gc->interrupt_trigger == IRQ_TYPE_LEVEL_HIGH ? >> + handle_level_irq : handle_simple_irq, IRQ_TYPE_NONE); > > AFAIK, handle_bad_irq() should be used here. > G'day Andy Grepping drivers/gpio find a combination of handle_simple_irq handle_level_irq handle_edge_irq handle_bad_irq used in gpiochip_irqchip_add The ones which use handle_bad_irq call irq_set_handler_locked in their irq_type callback to either handle_level_irq / handle_edge_irq So I think in this case it's correct. But I'm no expert.
On Fri, Feb 17, 2017 at 1:32 PM, Phil Reid <preid@electromag.com.au> wrote: > On 17/02/2017 17:23, Andy Shevchenko wrote: >> >> On Fri, Feb 17, 2017 at 11:12 AM, Phil Reid <preid@electromag.com.au> >> wrote: >>> >>> When a threaded irq handler is chained attached to one of the gpio >>> pins when configure for level irq the altera_gpio_irq_leveL_high_handler >>> does not mask the interrupt while being handled by the chained irq. >>> This resulting in the threaded irq not getting enough cycles to complete >>> quickly enough before the irq was disabled as faulty. >>> It looks like handle_level_irq should be used in this situation >>> instead of handle_simple_irq. >> >> >>> @@ -310,7 +310,8 @@ static int altera_gpio_probe(struct platform_device >>> *pdev) >>> altera_gc->interrupt_trigger = reg; >>> >>> ret = gpiochip_irqchip_add(&altera_gc->mmchip.gc, >>> &altera_irq_chip, 0, >>> - handle_simple_irq, IRQ_TYPE_NONE); >>> + altera_gc->interrupt_trigger == IRQ_TYPE_LEVEL_HIGH ? >>> + handle_level_irq : handle_simple_irq, IRQ_TYPE_NONE); >> >> >> AFAIK, handle_bad_irq() should be used here. >> > G'day Andy > > Grepping drivers/gpio find a combination of > handle_simple_irq > handle_level_irq > handle_edge_irq > handle_bad_irq > used in gpiochip_irqchip_add Try to add date of change and amount of use. I bet handle_bad_irq() would be the winner. > The ones which use handle_bad_irq call irq_set_handler_locked in their > irq_type callback to either handle_level_irq / handle_edge_irq Yep. > So I think in this case it's correct. But I'm no expert. I dunno.
On Fri, Feb 17, 2017 at 10:12 AM, Phil Reid <preid@electromag.com.au> wrote: > ret = gpiochip_irqchip_add(&altera_gc->mmchip.gc, &altera_irq_chip, 0, > - handle_simple_irq, IRQ_TYPE_NONE); > + altera_gc->interrupt_trigger == IRQ_TYPE_LEVEL_HIGH ? > + handle_level_irq : handle_simple_irq, IRQ_TYPE_NONE); I would say: set it to handle_bad_irq() for everything and then set it to handle_level_irq() or handle_simple_irq() in the .set_type() function using the rq_set_handler_locked() callback like everyone else, nicely reflecting the synthesized trigger type. I think that would work? Yours, Linus Walleij -- To unsubscribe from this list: send the line "unsubscribe linux-gpio" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/gpio/gpio-altera.c b/drivers/gpio/gpio-altera.c index 5bddbd5..d67dcca 100644 --- a/drivers/gpio/gpio-altera.c +++ b/drivers/gpio/gpio-altera.c @@ -310,7 +310,8 @@ static int altera_gpio_probe(struct platform_device *pdev) altera_gc->interrupt_trigger = reg; ret = gpiochip_irqchip_add(&altera_gc->mmchip.gc, &altera_irq_chip, 0, - handle_simple_irq, IRQ_TYPE_NONE); + altera_gc->interrupt_trigger == IRQ_TYPE_LEVEL_HIGH ? + handle_level_irq : handle_simple_irq, IRQ_TYPE_NONE); if (ret) { dev_err(&pdev->dev, "could not add irqchip\n");
When a threaded irq handler is chained attached to one of the gpio pins when configure for level irq the altera_gpio_irq_leveL_high_handler does not mask the interrupt while being handled by the chained irq. This resulting in the threaded irq not getting enough cycles to complete quickly enough before the irq was disabled as faulty. It looks like handle_level_irq should be used in this situation instead of handle_simple_irq. Signed-off-by: Phil Reid <preid@electromag.com.au> --- drivers/gpio/gpio-altera.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)