diff mbox

[LEDE-DEV] ar71xx: add Abicom SC300M support

Message ID 20170111161952.32716-1-i@conorogorman.net
State Changes Requested
Headers show

Commit Message

Conor O'Gorman Jan. 11, 2017, 4:19 p.m. UTC 
Support Abicom International Scorpion SC300M Module

QCA9550 700MHz Extended Temperature Range
256MB DDR2
256MB Nand Flash
16MB SPI Flash
802.11a/na/b/g/ng
GPIO x 22, USB x2, PCIe x2
10/100/1000 Ethernet
23dBm, Optional Onboard Antenna
DC Input, 8-20V DC
85 x 55 mm

Signed-off-by: Conor O'Gorman <i@conorogorman.net>
---
 target/linux/ar71xx/base-files/etc/board.d/01_leds |   1 +
 .../linux/ar71xx/base-files/etc/board.d/02_network |   1 +
 target/linux/ar71xx/base-files/etc/diag.sh         |   3 +-
 target/linux/ar71xx/base-files/lib/ar71xx.sh       |   3 +
 .../ar71xx/base-files/lib/upgrade/platform.sh      |   1 +
 target/linux/ar71xx/config-4.4                     |   1 +
 .../ar71xx/files/arch/mips/ath79/Kconfig.openwrt   |  11 ++
 target/linux/ar71xx/files/arch/mips/ath79/Makefile |   1 +
 .../ar71xx/files/arch/mips/ath79/mach-sc300m.c     | 132 +++++++++++++++++++++
 .../linux/ar71xx/files/arch/mips/ath79/machtypes.h |   1 +
 target/linux/ar71xx/image/generic.mk               |  10 ++
 11 files changed, 164 insertions(+), 1 deletion(-)
 create mode 100644 target/linux/ar71xx/files/arch/mips/ath79/mach-sc300m.c

Comments

John Crispin Jan. 15, 2017, 1:52 p.m. UTC | #1 
Hi,

looks good, one minor nitpicks inline

On 11/01/2017 17:19, Conor O'Gorman wrote:
> Support Abicom International Scorpion SC300M Module
> 
> QCA9550 700MHz Extended Temperature Range
> 256MB DDR2
> 256MB Nand Flash
> 16MB SPI Flash
> 802.11a/na/b/g/ng
> GPIO x 22, USB x2, PCIe x2
> 10/100/1000 Ethernet
> 23dBm, Optional Onboard Antenna
> DC Input, 8-20V DC
> 85 x 55 mm
> 
> Signed-off-by: Conor O'Gorman <i@conorogorman.net>
> ---
>  target/linux/ar71xx/base-files/etc/board.d/01_leds |   1 +
>  .../linux/ar71xx/base-files/etc/board.d/02_network |   1 +
>  target/linux/ar71xx/base-files/etc/diag.sh         |   3 +-
>  target/linux/ar71xx/base-files/lib/ar71xx.sh       |   3 +
>  .../ar71xx/base-files/lib/upgrade/platform.sh      |   1 +
>  target/linux/ar71xx/config-4.4                     |   1 +
>  .../ar71xx/files/arch/mips/ath79/Kconfig.openwrt   |  11 ++
>  target/linux/ar71xx/files/arch/mips/ath79/Makefile |   1 +
>  .../ar71xx/files/arch/mips/ath79/mach-sc300m.c     | 132 +++++++++++++++++++++
>  .../linux/ar71xx/files/arch/mips/ath79/machtypes.h |   1 +
>  target/linux/ar71xx/image/generic.mk               |  10 ++
>  11 files changed, 164 insertions(+), 1 deletion(-)
>  create mode 100644 target/linux/ar71xx/files/arch/mips/ath79/mach-sc300m.c
> 
> diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds
> index 5a2bf0c..5be9d4a 100755
> --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds
> +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds
> @@ -279,6 +279,7 @@ gl-mifi)
>  	esac
>  	;;
>  gl-domino|\
> +sc300m|\
>  wrt160nl)
>  	ucidef_set_led_wlan "wlan" "WLAN" "$board:blue:wlan" "phy0tpt"
>  	;;
> diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network
> index 66274db..54069ce 100755
> --- a/target/linux/ar71xx/base-files/etc/board.d/02_network
> +++ b/target/linux/ar71xx/base-files/etc/board.d/02_network
> @@ -93,6 +93,7 @@ ar71xx_setup_interfaces()
>  	rb-sxt5n|\
>  	re450|\
>  	rocket-m-xw|\
> +	sc300m |\
>  	tl-mr10u|\
>  	tl-mr11u|\
>  	tl-mr12u|\
> diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh
> index d060ccf..36f2c43 100644
> --- a/target/linux/ar71xx/base-files/etc/diag.sh
> +++ b/target/linux/ar71xx/base-files/etc/diag.sh
> @@ -295,7 +295,8 @@ get_status_led() {
>  	rb-sxt5n)
>  		status_led="rb:green:power"
>  		;;
> -	re450)
> +	re450|\
> +	sc300m)
>  		status_led="$board:blue:power"
>  		;;
>  	routerstation|\
> diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh
> index 1b30f4d..a8bdc67 100755
> --- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
> +++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
> @@ -881,6 +881,9 @@ ar71xx_board_detect() {
>  	*RW2458N)
>  		name="rw2458n"
>  		;;
> +	*SC300M)
> +		name="sc300m"
> +		;;
>  	*"SMART-300")
>  		name="smart-300"
>  		;;
> diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
> index 6341a31..74808ef 100755
> --- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
> @@ -226,6 +226,7 @@ platform_check_image() {
>  	rocket-m-xw|\
>  	rocket-m|\
>  	rw2458n|\
> +	sc300m|\
>  	sr3200|\
>  	tew-632brp|\
>  	tew-712br|\
> diff --git a/target/linux/ar71xx/config-4.4 b/target/linux/ar71xx/config-4.4
> index 4b2f736..daffdea 100644
> --- a/target/linux/ar71xx/config-4.4
> +++ b/target/linux/ar71xx/config-4.4
> @@ -147,6 +147,7 @@ CONFIG_ATH79_MACH_R6100=y
>  # CONFIG_ATH79_MACH_RBSXTLITE is not set
>  CONFIG_ATH79_MACH_RE450=y
>  CONFIG_ATH79_MACH_RW2458N=y
> +CONFIG_ATH79_MACH_SC300M=y
>  CONFIG_ATH79_MACH_SMART_300=y
>  CONFIG_ATH79_MACH_SOM9331=y
>  CONFIG_ATH79_MACH_SR3200=y
> diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
> index 21d6b51..56889d7 100644
> --- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
> +++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
> @@ -1,3 +1,14 @@
> +config ATH79_MACH_SC300M
> +	bool "Abicom SC300M board support"
> +	select SOC_QCA955X
> +	select ATH79_DEV_AP9X_PCI if PCI
> +	select ATH79_DEV_ETH
> +	select ATH79_DEV_GPIO_BUTTONS
> +	select ATH79_DEV_LEDS_GPIO
> +	select ATH79_DEV_M25P80
> +	select ATH79_DEV_USB
> +	select ATH79_DEV_WMAC


This is not ordered correctly

	John


> +
>  config ATH79_MACH_ALFA_AP120C
>  	bool "ALFA Network AP120C board support"
>  	select ATH79_DEV_AP9X_PCI if PCI
> diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
> index 6384c06..915b34e 100644
> --- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile
> +++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
> @@ -151,6 +151,7 @@ obj-$(CONFIG_ATH79_MACH_RB95X)			+= mach-rb95x.o
>  obj-$(CONFIG_ATH79_MACH_RBSXTLITE)		+= mach-rbsxtlite.o
>  obj-$(CONFIG_ATH79_MACH_RE450)			+= mach-re450.o
>  obj-$(CONFIG_ATH79_MACH_RW2458N)		+= mach-rw2458n.o
> +obj-$(CONFIG_ATH79_MACH_SC300M)			+= mach-sc300m.o
>  obj-$(CONFIG_ATH79_MACH_SMART_300)		+= mach-smart-300.o
>  obj-$(CONFIG_ATH79_MACH_SOM9331)		+= mach-som9331.o
>  obj-$(CONFIG_ATH79_MACH_SR3200)			+= mach-sr3200.o
> diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-sc300m.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-sc300m.c
> new file mode 100644
> index 0000000..45ec58d
> --- /dev/null
> +++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-sc300m.c
> @@ -0,0 +1,132 @@
> +/*
> + * Abicom International Scorpion SC300M Module support.
> + *
> + * Copyright (c) 2012 Qualcomm Atheros
> + * Copyright (c) 2012-2013 Gabor Juhos <juhosg@openwrt.org>
> + * Copyright (c) 2017 Conor O'Gorman <i@conorogorman.net>
> + *
> + * Permission to use, copy, modify, and/or distribute this software for any
> + * purpose with or without fee is hereby granted, provided that the above
> + * copyright notice and this permission notice appear in all copies.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
> + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
> + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
> + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
> + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
> + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
> + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
> + *
> + */
> +
> +#include <linux/platform_device.h>
> +#include <linux/platform_data/phy-at803x.h>
> +
> +#include <asm/mach-ath79/ar71xx_regs.h>
> +
> +#include "common.h"
> +#include "pci.h"
> +#include "dev-ap9x-pci.h"
> +#include "dev-gpio-buttons.h"
> +#include "dev-eth.h"
> +#include "dev-leds-gpio.h"
> +#include "dev-m25p80.h"
> +#include "dev-nfc.h"
> +#include "dev-usb.h"
> +#include "dev-wmac.h"
> +#include "machtypes.h"
> +
> +#define SC300M_GPIO_LED_WLAN		0
> +#define SC300M_GPIO_LED_POWER		1
> +
> +#define SC300M_GPIO_BTN_RESET		17
> +
> +#define SC300M_KEYS_POLL_INTERVAL	20	/* msecs */
> +#define SC300M_KEYS_DEBOUNCE_INTERVAL	(3 * SC300M_KEYS_POLL_INTERVAL)
> +
> +#define SC300M_MAC0_OFFSET		0
> +#define SC300M_MAC1_OFFSET		6
> +#define SC300M_WMAC_CALDATA_OFFSET	0x1000
> +#define SC300M_PCIE_CALDATA_OFFSET	0x5000
> +
> +static struct gpio_led sc300m_leds_gpio[] __initdata = {
> +	{
> +		.name		= "sc300m:blue:wlan",
> +		.gpio		= SC300M_GPIO_LED_WLAN,
> +		.active_low	= 1,
> +	},
> +	{
> +		.name		= "sc300m:blue:power",
> +		.gpio		= SC300M_GPIO_LED_POWER,
> +		.active_low	= 1,
> +	}
> +};
> +
> +static struct gpio_keys_button sc300m_gpio_keys[] __initdata = {
> +	{
> +		.desc		= "reset",
> +		.type		= EV_KEY,
> +		.code		= KEY_RESTART,
> +		.debounce_interval = SC300M_KEYS_DEBOUNCE_INTERVAL,
> +		.gpio		= SC300M_GPIO_BTN_RESET,
> +		.active_low	= 1,
> +	}
> +};
> +
> +static struct at803x_platform_data at803x_data = {
> +	.disable_smarteee = 1,
> +	.enable_rgmii_rx_delay = 0,
> +	.enable_rgmii_tx_delay = 0,
> +};
> +
> +static struct mdio_board_info sc300m_mdio0_info[] = {
> +	{
> +		.bus_id = "ag71xx-mdio.0",
> +		.phy_addr = 1,
> +		.platform_data = &at803x_data,
> +	},
> +};
> +
> +static void __init sc300m_setup(void)
> +{
> +	u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
> +
> +	ath79_register_m25p80(NULL);
> +
> +	ath79_register_leds_gpio(-1, ARRAY_SIZE(sc300m_leds_gpio),
> +				 sc300m_leds_gpio);
> +	ath79_register_gpio_keys_polled(-1, SC300M_KEYS_POLL_INTERVAL,
> +					ARRAY_SIZE(sc300m_gpio_keys),
> +					sc300m_gpio_keys);
> +
> +	ath79_register_usb();
> +	ath79_register_nfc();
> +
> +	ath79_register_wmac(art + SC300M_WMAC_CALDATA_OFFSET, NULL);
> +
> +	ath79_register_mdio(0, 0);
> +	mdiobus_register_board_info(sc300m_mdio0_info,
> +				    ARRAY_SIZE(sc300m_mdio0_info));
> +
> +	ath79_init_mac(ath79_eth0_data.mac_addr, art + SC300M_MAC0_OFFSET, 0);
> +
> +	ath79_eth0_pll_data.pll_1000 = 0xa6000101;
> +	ath79_eth0_pll_data.pll_100 = 0xa4000101;
> +	/* GMAC0 is connected to the RMGII interface */
> +	ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
> +	ath79_eth0_data.phy_mask = 0xF;
> +	ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
> +
> +	ath79_register_eth(0);
> +
> +	/* GMAC1 is connected tot eh SGMII interface */
> +	ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
> +	ath79_eth1_data.speed = SPEED_1000;
> +	ath79_eth1_data.duplex = DUPLEX_FULL;
> +
> +	ath79_register_eth(1);
> +
> +	ath79_register_pci();
> +}
> +
> +MIPS_MACHINE(ATH79_MACH_SC300M, "SC300M", "Abicom SC300M", sc300m_setup);
> diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
> index 9402185..b1e29f9 100644
> --- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
> +++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
> @@ -168,6 +168,7 @@ enum ath79_mach_type {
>  	ATH79_MACH_RB_SXTLITE5ND,		/* Mikrotik RouterBOARD SXT Lite 5nD */
>  	ATH79_MACH_RE450,			/* TP-LINK RE450 */
>  	ATH79_MACH_RW2458N,			/* Redwave RW2458N */
> +	ATH79_MACH_SC300M,			/* Abicom SC300M */
>  	ATH79_MACH_SMART_300,			/* NC-LINK SMART-300 */
>  	ATH79_MACH_SOM9331,			/* OpenEmbed SOM9331 */
>  	ATH79_MACH_SR3200,			/* YunCore SR3200 */
> diff --git a/target/linux/ar71xx/image/generic.mk b/target/linux/ar71xx/image/generic.mk
> index e2867e6..f8445b5 100644
> --- a/target/linux/ar71xx/image/generic.mk
> +++ b/target/linux/ar71xx/image/generic.mk
> @@ -464,6 +464,16 @@ define Device/onion-omega
>  endef
>  TARGET_DEVICES += onion-omega
>  
> +define Device/sc300m
> +  DEVICE_TITLE := Abicom SC300M
> +  DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport
> +  BOARDNAME = SC300M
> +  IMAGE_SIZE = 15744k
> +  CONSOLE = ttyS0,115200
> +  MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env),15744k(firmware),128k(APConfig),128k(kplog),64k(ART)
> +endef
> +TARGET_DEVICES += sc300m
> +
>  define Device/smart-300
>    $(Device/tplink-8mlzma)
>    DEVICE_TITLE := NC-LINK SMART-300
>
Sebastian Kemper Jan. 15, 2017, 3:10 p.m. UTC | #2 
Hi,

Another nitpick, there's a typo in a comment:

"/* GMAC1 is connected tot eh SGMII interface */"

Regards,
Sebastian

Am 15. Januar 2017 14:52:17 MEZ schrieb John Crispin <john@phrozen.org>:
>Hi,
>
>looks good, one minor nitpicks inline
>
>On 11/01/2017 17:19, Conor O'Gorman wrote:
>> Support Abicom International Scorpion SC300M Module
>> 
>> QCA9550 700MHz Extended Temperature Range
>> 256MB DDR2
>> 256MB Nand Flash
>> 16MB SPI Flash
>> 802.11a/na/b/g/ng
>> GPIO x 22, USB x2, PCIe x2
>> 10/100/1000 Ethernet
>> 23dBm, Optional Onboard Antenna
>> DC Input, 8-20V DC
>> 85 x 55 mm
>> 
>> Signed-off-by: Conor O'Gorman <i@conorogorman.net>
>> ---
>>  target/linux/ar71xx/base-files/etc/board.d/01_leds |   1 +
>>  .../linux/ar71xx/base-files/etc/board.d/02_network |   1 +
>>  target/linux/ar71xx/base-files/etc/diag.sh         |   3 +-
>>  target/linux/ar71xx/base-files/lib/ar71xx.sh       |   3 +
>>  .../ar71xx/base-files/lib/upgrade/platform.sh      |   1 +
>>  target/linux/ar71xx/config-4.4                     |   1 +
>>  .../ar71xx/files/arch/mips/ath79/Kconfig.openwrt   |  11 ++
>>  target/linux/ar71xx/files/arch/mips/ath79/Makefile |   1 +
>>  .../ar71xx/files/arch/mips/ath79/mach-sc300m.c     | 132
>+++++++++++++++++++++
>>  .../linux/ar71xx/files/arch/mips/ath79/machtypes.h |   1 +
>>  target/linux/ar71xx/image/generic.mk               |  10 ++
>>  11 files changed, 164 insertions(+), 1 deletion(-)
>>  create mode 100644
>target/linux/ar71xx/files/arch/mips/ath79/mach-sc300m.c
>> 
>> diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds
>b/target/linux/ar71xx/base-files/etc/board.d/01_leds
>> index 5a2bf0c..5be9d4a 100755
>> --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds
>> +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds
>> @@ -279,6 +279,7 @@ gl-mifi)
>>  	esac
>>  	;;
>>  gl-domino|\
>> +sc300m|\
>>  wrt160nl)
>>  	ucidef_set_led_wlan "wlan" "WLAN" "$board:blue:wlan" "phy0tpt"
>>  	;;
>> diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network
>b/target/linux/ar71xx/base-files/etc/board.d/02_network
>> index 66274db..54069ce 100755
>> --- a/target/linux/ar71xx/base-files/etc/board.d/02_network
>> +++ b/target/linux/ar71xx/base-files/etc/board.d/02_network
>> @@ -93,6 +93,7 @@ ar71xx_setup_interfaces()
>>  	rb-sxt5n|\
>>  	re450|\
>>  	rocket-m-xw|\
>> +	sc300m |\
>>  	tl-mr10u|\
>>  	tl-mr11u|\
>>  	tl-mr12u|\
>> diff --git a/target/linux/ar71xx/base-files/etc/diag.sh
>b/target/linux/ar71xx/base-files/etc/diag.sh
>> index d060ccf..36f2c43 100644
>> --- a/target/linux/ar71xx/base-files/etc/diag.sh
>> +++ b/target/linux/ar71xx/base-files/etc/diag.sh
>> @@ -295,7 +295,8 @@ get_status_led() {
>>  	rb-sxt5n)
>>  		status_led="rb:green:power"
>>  		;;
>> -	re450)
>> +	re450|\
>> +	sc300m)
>>  		status_led="$board:blue:power"
>>  		;;
>>  	routerstation|\
>> diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh
>b/target/linux/ar71xx/base-files/lib/ar71xx.sh
>> index 1b30f4d..a8bdc67 100755
>> --- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
>> +++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
>> @@ -881,6 +881,9 @@ ar71xx_board_detect() {
>>  	*RW2458N)
>>  		name="rw2458n"
>>  		;;
>> +	*SC300M)
>> +		name="sc300m"
>> +		;;
>>  	*"SMART-300")
>>  		name="smart-300"
>>  		;;
>> diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
>b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
>> index 6341a31..74808ef 100755
>> --- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
>> +++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
>> @@ -226,6 +226,7 @@ platform_check_image() {
>>  	rocket-m-xw|\
>>  	rocket-m|\
>>  	rw2458n|\
>> +	sc300m|\
>>  	sr3200|\
>>  	tew-632brp|\
>>  	tew-712br|\
>> diff --git a/target/linux/ar71xx/config-4.4
>b/target/linux/ar71xx/config-4.4
>> index 4b2f736..daffdea 100644
>> --- a/target/linux/ar71xx/config-4.4
>> +++ b/target/linux/ar71xx/config-4.4
>> @@ -147,6 +147,7 @@ CONFIG_ATH79_MACH_R6100=y
>>  # CONFIG_ATH79_MACH_RBSXTLITE is not set
>>  CONFIG_ATH79_MACH_RE450=y
>>  CONFIG_ATH79_MACH_RW2458N=y
>> +CONFIG_ATH79_MACH_SC300M=y
>>  CONFIG_ATH79_MACH_SMART_300=y
>>  CONFIG_ATH79_MACH_SOM9331=y
>>  CONFIG_ATH79_MACH_SR3200=y
>> diff --git
>a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
>b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
>> index 21d6b51..56889d7 100644
>> --- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
>> +++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
>> @@ -1,3 +1,14 @@
>> +config ATH79_MACH_SC300M
>> +	bool "Abicom SC300M board support"
>> +	select SOC_QCA955X
>> +	select ATH79_DEV_AP9X_PCI if PCI
>> +	select ATH79_DEV_ETH
>> +	select ATH79_DEV_GPIO_BUTTONS
>> +	select ATH79_DEV_LEDS_GPIO
>> +	select ATH79_DEV_M25P80
>> +	select ATH79_DEV_USB
>> +	select ATH79_DEV_WMAC
>
>
>This is not ordered correctly
>
>	John
>
>
>> +
>>  config ATH79_MACH_ALFA_AP120C
>>  	bool "ALFA Network AP120C board support"
>>  	select ATH79_DEV_AP9X_PCI if PCI
>> diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile
>b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
>> index 6384c06..915b34e 100644
>> --- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile
>> +++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
>> @@ -151,6 +151,7 @@ obj-$(CONFIG_ATH79_MACH_RB95X)			+= mach-rb95x.o
>>  obj-$(CONFIG_ATH79_MACH_RBSXTLITE)		+= mach-rbsxtlite.o
>>  obj-$(CONFIG_ATH79_MACH_RE450)			+= mach-re450.o
>>  obj-$(CONFIG_ATH79_MACH_RW2458N)		+= mach-rw2458n.o
>> +obj-$(CONFIG_ATH79_MACH_SC300M)			+= mach-sc300m.o
>>  obj-$(CONFIG_ATH79_MACH_SMART_300)		+= mach-smart-300.o
>>  obj-$(CONFIG_ATH79_MACH_SOM9331)		+= mach-som9331.o
>>  obj-$(CONFIG_ATH79_MACH_SR3200)			+= mach-sr3200.o
>> diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-sc300m.c
>b/target/linux/ar71xx/files/arch/mips/ath79/mach-sc300m.c
>> new file mode 100644
>> index 0000000..45ec58d
>> --- /dev/null
>> +++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-sc300m.c
>> @@ -0,0 +1,132 @@
>> +/*
>> + * Abicom International Scorpion SC300M Module support.
>> + *
>> + * Copyright (c) 2012 Qualcomm Atheros
>> + * Copyright (c) 2012-2013 Gabor Juhos <juhosg@openwrt.org>
>> + * Copyright (c) 2017 Conor O'Gorman <i@conorogorman.net>
>> + *
>> + * Permission to use, copy, modify, and/or distribute this software
>for any
>> + * purpose with or without fee is hereby granted, provided that the
>above
>> + * copyright notice and this permission notice appear in all copies.
>> + *
>> + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL
>WARRANTIES
>> + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
>> + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE
>LIABLE FOR
>> + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY
>DAMAGES
>> + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER
>IN AN
>> + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING
>OUT OF
>> + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
>> + *
>> + */
>> +
>> +#include <linux/platform_device.h>
>> +#include <linux/platform_data/phy-at803x.h>
>> +
>> +#include <asm/mach-ath79/ar71xx_regs.h>
>> +
>> +#include "common.h"
>> +#include "pci.h"
>> +#include "dev-ap9x-pci.h"
>> +#include "dev-gpio-buttons.h"
>> +#include "dev-eth.h"
>> +#include "dev-leds-gpio.h"
>> +#include "dev-m25p80.h"
>> +#include "dev-nfc.h"
>> +#include "dev-usb.h"
>> +#include "dev-wmac.h"
>> +#include "machtypes.h"
>> +
>> +#define SC300M_GPIO_LED_WLAN		0
>> +#define SC300M_GPIO_LED_POWER		1
>> +
>> +#define SC300M_GPIO_BTN_RESET		17
>> +
>> +#define SC300M_KEYS_POLL_INTERVAL	20	/* msecs */
>> +#define SC300M_KEYS_DEBOUNCE_INTERVAL	(3 *
>SC300M_KEYS_POLL_INTERVAL)
>> +
>> +#define SC300M_MAC0_OFFSET		0
>> +#define SC300M_MAC1_OFFSET		6
>> +#define SC300M_WMAC_CALDATA_OFFSET	0x1000
>> +#define SC300M_PCIE_CALDATA_OFFSET	0x5000
>> +
>> +static struct gpio_led sc300m_leds_gpio[] __initdata = {
>> +	{
>> +		.name		= "sc300m:blue:wlan",
>> +		.gpio		= SC300M_GPIO_LED_WLAN,
>> +		.active_low	= 1,
>> +	},
>> +	{
>> +		.name		= "sc300m:blue:power",
>> +		.gpio		= SC300M_GPIO_LED_POWER,
>> +		.active_low	= 1,
>> +	}
>> +};
>> +
>> +static struct gpio_keys_button sc300m_gpio_keys[] __initdata = {
>> +	{
>> +		.desc		= "reset",
>> +		.type		= EV_KEY,
>> +		.code		= KEY_RESTART,
>> +		.debounce_interval = SC300M_KEYS_DEBOUNCE_INTERVAL,
>> +		.gpio		= SC300M_GPIO_BTN_RESET,
>> +		.active_low	= 1,
>> +	}
>> +};
>> +
>> +static struct at803x_platform_data at803x_data = {
>> +	.disable_smarteee = 1,
>> +	.enable_rgmii_rx_delay = 0,
>> +	.enable_rgmii_tx_delay = 0,
>> +};
>> +
>> +static struct mdio_board_info sc300m_mdio0_info[] = {
>> +	{
>> +		.bus_id = "ag71xx-mdio.0",
>> +		.phy_addr = 1,
>> +		.platform_data = &at803x_data,
>> +	},
>> +};
>> +
>> +static void __init sc300m_setup(void)
>> +{
>> +	u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
>> +
>> +	ath79_register_m25p80(NULL);
>> +
>> +	ath79_register_leds_gpio(-1, ARRAY_SIZE(sc300m_leds_gpio),
>> +				 sc300m_leds_gpio);
>> +	ath79_register_gpio_keys_polled(-1, SC300M_KEYS_POLL_INTERVAL,
>> +					ARRAY_SIZE(sc300m_gpio_keys),
>> +					sc300m_gpio_keys);
>> +
>> +	ath79_register_usb();
>> +	ath79_register_nfc();
>> +
>> +	ath79_register_wmac(art + SC300M_WMAC_CALDATA_OFFSET, NULL);
>> +
>> +	ath79_register_mdio(0, 0);
>> +	mdiobus_register_board_info(sc300m_mdio0_info,
>> +				    ARRAY_SIZE(sc300m_mdio0_info));
>> +
>> +	ath79_init_mac(ath79_eth0_data.mac_addr, art + SC300M_MAC0_OFFSET,
>0);
>> +
>> +	ath79_eth0_pll_data.pll_1000 = 0xa6000101;
>> +	ath79_eth0_pll_data.pll_100 = 0xa4000101;
>> +	/* GMAC0 is connected to the RMGII interface */
>> +	ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
>> +	ath79_eth0_data.phy_mask = 0xF;
>> +	ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
>> +
>> +	ath79_register_eth(0);
>> +
>> +	/* GMAC1 is connected tot eh SGMII interface */
>> +	ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
>> +	ath79_eth1_data.speed = SPEED_1000;
>> +	ath79_eth1_data.duplex = DUPLEX_FULL;
>> +
>> +	ath79_register_eth(1);
>> +
>> +	ath79_register_pci();
>> +}
>> +
>> +MIPS_MACHINE(ATH79_MACH_SC300M, "SC300M", "Abicom SC300M",
>sc300m_setup);
>> diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
>b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
>> index 9402185..b1e29f9 100644
>> --- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
>> +++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
>> @@ -168,6 +168,7 @@ enum ath79_mach_type {
>>  	ATH79_MACH_RB_SXTLITE5ND,		/* Mikrotik RouterBOARD SXT Lite 5nD */
>>  	ATH79_MACH_RE450,			/* TP-LINK RE450 */
>>  	ATH79_MACH_RW2458N,			/* Redwave RW2458N */
>> +	ATH79_MACH_SC300M,			/* Abicom SC300M */
>>  	ATH79_MACH_SMART_300,			/* NC-LINK SMART-300 */
>>  	ATH79_MACH_SOM9331,			/* OpenEmbed SOM9331 */
>>  	ATH79_MACH_SR3200,			/* YunCore SR3200 */
>> diff --git a/target/linux/ar71xx/image/generic.mk
>b/target/linux/ar71xx/image/generic.mk
>> index e2867e6..f8445b5 100644
>> --- a/target/linux/ar71xx/image/generic.mk
>> +++ b/target/linux/ar71xx/image/generic.mk
>> @@ -464,6 +464,16 @@ define Device/onion-omega
>>  endef
>>  TARGET_DEVICES += onion-omega
>>  
>> +define Device/sc300m
>> +  DEVICE_TITLE := Abicom SC300M
>> +  DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2
>kmod-usb-ledtrig-usbport
>> +  BOARDNAME = SC300M
>> +  IMAGE_SIZE = 15744k
>> +  CONSOLE = ttyS0,115200
>> +  MTDPARTS =
>spi0.0:256k(u-boot)ro,64k(u-boot-env),15744k(firmware),128k(APConfig),128k(kplog),64k(ART)
>> +endef
>> +TARGET_DEVICES += sc300m
>> +
>>  define Device/smart-300
>>    $(Device/tplink-8mlzma)
>>    DEVICE_TITLE := NC-LINK SMART-300
>> 
>
>_______________________________________________
>Lede-dev mailing list
>Lede-dev@lists.infradead.org
>http://lists.infradead.org/mailman/listinfo/lede-dev
diff mbox

Patch

diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds
index 5a2bf0c..5be9d4a 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds
@@ -279,6 +279,7 @@  gl-mifi)
 	esac
 	;;
 gl-domino|\
+sc300m|\
 wrt160nl)
 	ucidef_set_led_wlan "wlan" "WLAN" "$board:blue:wlan" "phy0tpt"
 	;;
diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network
index 66274db..54069ce 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/02_network
+++ b/target/linux/ar71xx/base-files/etc/board.d/02_network
@@ -93,6 +93,7 @@  ar71xx_setup_interfaces()
 	rb-sxt5n|\
 	re450|\
 	rocket-m-xw|\
+	sc300m |\
 	tl-mr10u|\
 	tl-mr11u|\
 	tl-mr12u|\
diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh
index d060ccf..36f2c43 100644
--- a/target/linux/ar71xx/base-files/etc/diag.sh
+++ b/target/linux/ar71xx/base-files/etc/diag.sh
@@ -295,7 +295,8 @@  get_status_led() {
 	rb-sxt5n)
 		status_led="rb:green:power"
 		;;
-	re450)
+	re450|\
+	sc300m)
 		status_led="$board:blue:power"
 		;;
 	routerstation|\
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index 1b30f4d..a8bdc67 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -881,6 +881,9 @@  ar71xx_board_detect() {
 	*RW2458N)
 		name="rw2458n"
 		;;
+	*SC300M)
+		name="sc300m"
+		;;
 	*"SMART-300")
 		name="smart-300"
 		;;
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index 6341a31..74808ef 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -226,6 +226,7 @@  platform_check_image() {
 	rocket-m-xw|\
 	rocket-m|\
 	rw2458n|\
+	sc300m|\
 	sr3200|\
 	tew-632brp|\
 	tew-712br|\
diff --git a/target/linux/ar71xx/config-4.4 b/target/linux/ar71xx/config-4.4
index 4b2f736..daffdea 100644
--- a/target/linux/ar71xx/config-4.4
+++ b/target/linux/ar71xx/config-4.4
@@ -147,6 +147,7 @@  CONFIG_ATH79_MACH_R6100=y
 # CONFIG_ATH79_MACH_RBSXTLITE is not set
 CONFIG_ATH79_MACH_RE450=y
 CONFIG_ATH79_MACH_RW2458N=y
+CONFIG_ATH79_MACH_SC300M=y
 CONFIG_ATH79_MACH_SMART_300=y
 CONFIG_ATH79_MACH_SOM9331=y
 CONFIG_ATH79_MACH_SR3200=y
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
index 21d6b51..56889d7 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
@@ -1,3 +1,14 @@ 
+config ATH79_MACH_SC300M
+	bool "Abicom SC300M board support"
+	select SOC_QCA955X
+	select ATH79_DEV_AP9X_PCI if PCI
+	select ATH79_DEV_ETH
+	select ATH79_DEV_GPIO_BUTTONS
+	select ATH79_DEV_LEDS_GPIO
+	select ATH79_DEV_M25P80
+	select ATH79_DEV_USB
+	select ATH79_DEV_WMAC
+
 config ATH79_MACH_ALFA_AP120C
 	bool "ALFA Network AP120C board support"
 	select ATH79_DEV_AP9X_PCI if PCI
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
index 6384c06..915b34e 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
@@ -151,6 +151,7 @@  obj-$(CONFIG_ATH79_MACH_RB95X)			+= mach-rb95x.o
 obj-$(CONFIG_ATH79_MACH_RBSXTLITE)		+= mach-rbsxtlite.o
 obj-$(CONFIG_ATH79_MACH_RE450)			+= mach-re450.o
 obj-$(CONFIG_ATH79_MACH_RW2458N)		+= mach-rw2458n.o
+obj-$(CONFIG_ATH79_MACH_SC300M)			+= mach-sc300m.o
 obj-$(CONFIG_ATH79_MACH_SMART_300)		+= mach-smart-300.o
 obj-$(CONFIG_ATH79_MACH_SOM9331)		+= mach-som9331.o
 obj-$(CONFIG_ATH79_MACH_SR3200)			+= mach-sr3200.o
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-sc300m.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-sc300m.c
new file mode 100644
index 0000000..45ec58d
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-sc300m.c
@@ -0,0 +1,132 @@ 
+/*
+ * Abicom International Scorpion SC300M Module support.
+ *
+ * Copyright (c) 2012 Qualcomm Atheros
+ * Copyright (c) 2012-2013 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright (c) 2017 Conor O'Gorman <i@conorogorman.net>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include <linux/platform_device.h>
+#include <linux/platform_data/phy-at803x.h>
+
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include "common.h"
+#include "pci.h"
+#include "dev-ap9x-pci.h"
+#include "dev-gpio-buttons.h"
+#include "dev-eth.h"
+#include "dev-leds-gpio.h"
+#include "dev-m25p80.h"
+#include "dev-nfc.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "machtypes.h"
+
+#define SC300M_GPIO_LED_WLAN		0
+#define SC300M_GPIO_LED_POWER		1
+
+#define SC300M_GPIO_BTN_RESET		17
+
+#define SC300M_KEYS_POLL_INTERVAL	20	/* msecs */
+#define SC300M_KEYS_DEBOUNCE_INTERVAL	(3 * SC300M_KEYS_POLL_INTERVAL)
+
+#define SC300M_MAC0_OFFSET		0
+#define SC300M_MAC1_OFFSET		6
+#define SC300M_WMAC_CALDATA_OFFSET	0x1000
+#define SC300M_PCIE_CALDATA_OFFSET	0x5000
+
+static struct gpio_led sc300m_leds_gpio[] __initdata = {
+	{
+		.name		= "sc300m:blue:wlan",
+		.gpio		= SC300M_GPIO_LED_WLAN,
+		.active_low	= 1,
+	},
+	{
+		.name		= "sc300m:blue:power",
+		.gpio		= SC300M_GPIO_LED_POWER,
+		.active_low	= 1,
+	}
+};
+
+static struct gpio_keys_button sc300m_gpio_keys[] __initdata = {
+	{
+		.desc		= "reset",
+		.type		= EV_KEY,
+		.code		= KEY_RESTART,
+		.debounce_interval = SC300M_KEYS_DEBOUNCE_INTERVAL,
+		.gpio		= SC300M_GPIO_BTN_RESET,
+		.active_low	= 1,
+	}
+};
+
+static struct at803x_platform_data at803x_data = {
+	.disable_smarteee = 1,
+	.enable_rgmii_rx_delay = 0,
+	.enable_rgmii_tx_delay = 0,
+};
+
+static struct mdio_board_info sc300m_mdio0_info[] = {
+	{
+		.bus_id = "ag71xx-mdio.0",
+		.phy_addr = 1,
+		.platform_data = &at803x_data,
+	},
+};
+
+static void __init sc300m_setup(void)
+{
+	u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
+
+	ath79_register_m25p80(NULL);
+
+	ath79_register_leds_gpio(-1, ARRAY_SIZE(sc300m_leds_gpio),
+				 sc300m_leds_gpio);
+	ath79_register_gpio_keys_polled(-1, SC300M_KEYS_POLL_INTERVAL,
+					ARRAY_SIZE(sc300m_gpio_keys),
+					sc300m_gpio_keys);
+
+	ath79_register_usb();
+	ath79_register_nfc();
+
+	ath79_register_wmac(art + SC300M_WMAC_CALDATA_OFFSET, NULL);
+
+	ath79_register_mdio(0, 0);
+	mdiobus_register_board_info(sc300m_mdio0_info,
+				    ARRAY_SIZE(sc300m_mdio0_info));
+
+	ath79_init_mac(ath79_eth0_data.mac_addr, art + SC300M_MAC0_OFFSET, 0);
+
+	ath79_eth0_pll_data.pll_1000 = 0xa6000101;
+	ath79_eth0_pll_data.pll_100 = 0xa4000101;
+	/* GMAC0 is connected to the RMGII interface */
+	ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
+	ath79_eth0_data.phy_mask = 0xF;
+	ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+
+	ath79_register_eth(0);
+
+	/* GMAC1 is connected tot eh SGMII interface */
+	ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
+	ath79_eth1_data.speed = SPEED_1000;
+	ath79_eth1_data.duplex = DUPLEX_FULL;
+
+	ath79_register_eth(1);
+
+	ath79_register_pci();
+}
+
+MIPS_MACHINE(ATH79_MACH_SC300M, "SC300M", "Abicom SC300M", sc300m_setup);
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
index 9402185..b1e29f9 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
+++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
@@ -168,6 +168,7 @@  enum ath79_mach_type {
 	ATH79_MACH_RB_SXTLITE5ND,		/* Mikrotik RouterBOARD SXT Lite 5nD */
 	ATH79_MACH_RE450,			/* TP-LINK RE450 */
 	ATH79_MACH_RW2458N,			/* Redwave RW2458N */
+	ATH79_MACH_SC300M,			/* Abicom SC300M */
 	ATH79_MACH_SMART_300,			/* NC-LINK SMART-300 */
 	ATH79_MACH_SOM9331,			/* OpenEmbed SOM9331 */
 	ATH79_MACH_SR3200,			/* YunCore SR3200 */
diff --git a/target/linux/ar71xx/image/generic.mk b/target/linux/ar71xx/image/generic.mk
index e2867e6..f8445b5 100644
--- a/target/linux/ar71xx/image/generic.mk
+++ b/target/linux/ar71xx/image/generic.mk
@@ -464,6 +464,16 @@  define Device/onion-omega
 endef
 TARGET_DEVICES += onion-omega
 
+define Device/sc300m
+  DEVICE_TITLE := Abicom SC300M
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-usb-ledtrig-usbport
+  BOARDNAME = SC300M
+  IMAGE_SIZE = 15744k
+  CONSOLE = ttyS0,115200
+  MTDPARTS = spi0.0:256k(u-boot)ro,64k(u-boot-env),15744k(firmware),128k(APConfig),128k(kplog),64k(ART)
+endef
+TARGET_DEVICES += sc300m
+
 define Device/smart-300
   $(Device/tplink-8mlzma)
   DEVICE_TITLE := NC-LINK SMART-300