Message ID | 9bd69052-c5bb-731c-c01e-de42d1968718@axis.com |
---|---|
State | RFC, archived |
Delegated to: | David Miller |
Headers | show |
Hi Niklas, Às 10:59 AM de 1/4/2017, Niklas Cassel escreveu: > Hello Joao > > I just tested this series using the dwc_eth_qos DT bindings. > Good work! > > Unfortunately I get the following error: > > <3>[ 12.032463] dwc-eth-dwmac f8010000.ethernet eth0: stmmac_open: ERROR: allocating the WoL IRQ -1098801248 (-22) > > > This appears to be because of a corner case in stmmac_platform.c > where wol_irq can differ from the normal irq. > > Adding the following one liner fixes the problem: > > > --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c > +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c > @@ -125,6 +125,7 @@ static int dwc_eth_dwmac_probe(struct platform_device *pdev) > } > return stmmac_res.irq; > } > + stmmac_res.wol_irq = stmmac_res.irq; > > res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > stmmac_res.addr = devm_ioremap_resource(&pdev->dev, res); > Ok, I'll add this fix to the patch and give a check to the clks. I already sent a v1 patch set to net-dev, and I am now going to generate v2 so it would be great to have your tested.by tag to push it faster :) Thanks! > > > > I have one comment about clocks interleaved as well > > > > On 01/04/2017 10:44 AM, Joao Pinto wrote: >> This patch adds a new glue driver called dwmac-dwc-qos-eth which >> was based in the dwc_eth_qos as is. To assure retro-compatibility a slight >> tweak was also added to stmmac_platform. >> >> Signed-off-by: Joao Pinto <jpinto@synopsys.com> >> Reviewed-by: Lars Persson <larper@axis.com> >> --- >> .../bindings/net/snps,dwc-qos-ethernet.txt | 3 + >> drivers/net/ethernet/stmicro/stmmac/Kconfig | 9 + >> drivers/net/ethernet/stmicro/stmmac/Makefile | 1 + >> .../ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c | 199 +++++++++++++++++++++ >> .../net/ethernet/stmicro/stmmac/stmmac_platform.c | 15 +- >> 5 files changed, 224 insertions(+), 3 deletions(-) >> create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >> >> diff --git a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt >> index d93f71c..21d27aa 100644 >> --- a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt >> +++ b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt >> @@ -1,5 +1,8 @@ >> * Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC) >> >> +This binding is deprecated, but it continues to be supported, but new >> +features should be preferably added to the stmmac binding document. >> + >> This binding supports the Synopsys Designware Ethernet QoS (Quality Of Service) >> IP block. The IP supports multiple options for bus type, clocking and reset >> structure, and feature list. Consequently, a number of properties and list >> diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig >> index ab66248..99594e3 100644 >> --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig >> +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig >> @@ -29,6 +29,15 @@ config STMMAC_PLATFORM >> >> if STMMAC_PLATFORM >> >> +config DWMAC_DWC_QOS_ETH >> + tristate "Support for snps,dwc-qos-ethernet.txt DT binding." >> + select PHYLIB >> + select CRC32 >> + select MII >> + depends on OF && HAS_DMA >> + help >> + Support for chips using the snps,dwc-qos-ethernet.txt DT binding. >> + >> config DWMAC_GENERIC >> tristate "Generic driver for DWMAC" >> default STMMAC_PLATFORM >> diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile >> index 8f83a86..700c603 100644 >> --- a/drivers/net/ethernet/stmicro/stmmac/Makefile >> +++ b/drivers/net/ethernet/stmicro/stmmac/Makefile >> @@ -16,6 +16,7 @@ obj-$(CONFIG_DWMAC_SOCFPGA) += dwmac-altr-socfpga.o >> obj-$(CONFIG_DWMAC_STI) += dwmac-sti.o >> obj-$(CONFIG_DWMAC_STM32) += dwmac-stm32.o >> obj-$(CONFIG_DWMAC_SUNXI) += dwmac-sunxi.o >> +obj-$(CONFIG_DWMAC_DWC_QOS_ETH) += dwmac-dwc-qos-eth.o >> obj-$(CONFIG_DWMAC_GENERIC) += dwmac-generic.o >> stmmac-platform-objs:= stmmac_platform.o >> dwmac-altr-socfpga-objs := altr_tse_pcs.o dwmac-socfpga.o >> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >> new file mode 100644 >> index 0000000..8a6ac06 >> --- /dev/null >> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >> @@ -0,0 +1,199 @@ >> +/* >> + * Synopsys DWC Ethernet Quality-of-Service v4.10a linux driver >> + * >> + * Copyright (C) 2016 Joao Pinto <jpinto@synopsys.com> >> + * >> + * This program is free software; you can redistribute it and/or modify >> + * it under the terms of the GNU General Public License version 2 as >> + * published by the Free Software Foundation. >> + * >> + * You should have received a copy of the GNU General Public License >> + * along with this program. If not, see <https://urldefense.proofpoint.com/v2/url?u=http-3A__www.gnu.org_licenses_&d=DgIC-g&c=DPL6_X_6JkXFx7AXWqB0tg&r=s2fO0hii0OGNOv9qQy_HRXy-xAJUD1NNoEcc3io_kx0&m=DrobFP08nu4hh6e05EgeOl1xD34OacyiZ-be_GG829Q&s=WLSkpBK06KCu-_kvN305yE6YncNYcDG_Bk0pgqSBG1o&e= >. >> + */ >> + >> +#include <linux/clk.h> >> +#include <linux/clk-provider.h> >> +#include <linux/device.h> >> +#include <linux/ethtool.h> >> +#include <linux/io.h> >> +#include <linux/ioport.h> >> +#include <linux/module.h> >> +#include <linux/of_net.h> >> +#include <linux/mfd/syscon.h> >> +#include <linux/platform_device.h> >> +#include <linux/stmmac.h> >> + >> +#include "stmmac_platform.h" >> + >> +static int dwc_eth_dwmac_config_dt(struct platform_device *pdev, >> + struct plat_stmmacenet_data *plat_dat) >> +{ >> + struct device_node *np = pdev->dev.of_node; >> + u32 burst_map = 0; >> + u32 bit_index = 0; >> + u32 a_index = 0; >> + >> + if (!plat_dat->axi) { >> + plat_dat->axi = kzalloc(sizeof(struct stmmac_axi), GFP_KERNEL); >> + >> + if (!plat_dat->axi) >> + return -ENOMEM; >> + } >> + >> + plat_dat->axi->axi_lpi_en = of_property_read_bool(np, "snps,en-lpi"); >> + if (of_property_read_u32(np, "snps,write-requests", >> + &plat_dat->axi->axi_wr_osr_lmt)) { >> + /** >> + * Since the register has a reset value of 1, if property >> + * is missing, default to 1. >> + */ >> + plat_dat->axi->axi_wr_osr_lmt = 1; >> + } else { >> + /** >> + * If property exists, to keep the behavior from dwc_eth_qos, >> + * subtract one after parsing. >> + */ >> + plat_dat->axi->axi_wr_osr_lmt--; >> + } >> + >> + if (of_property_read_u32(np, "read,read-requests", >> + &plat_dat->axi->axi_rd_osr_lmt)) { >> + /** >> + * Since the register has a reset value of 1, if property >> + * is missing, default to 1. >> + */ >> + plat_dat->axi->axi_rd_osr_lmt = 1; >> + } else { >> + /** >> + * If property exists, to keep the behavior from dwc_eth_qos, >> + * subtract one after parsing. >> + */ >> + plat_dat->axi->axi_rd_osr_lmt--; >> + } >> + of_property_read_u32(np, "snps,burst-map", &burst_map); >> + >> + /* converts burst-map bitmask to burst array */ >> + for (bit_index = 0; bit_index < 7; bit_index++) { >> + if (burst_map & (1 << bit_index)) { >> + switch (bit_index) { >> + case 0: >> + plat_dat->axi->axi_blen[a_index] = 4; break; >> + case 1: >> + plat_dat->axi->axi_blen[a_index] = 8; break; >> + case 2: >> + plat_dat->axi->axi_blen[a_index] = 16; break; >> + case 3: >> + plat_dat->axi->axi_blen[a_index] = 32; break; >> + case 4: >> + plat_dat->axi->axi_blen[a_index] = 64; break; >> + case 5: >> + plat_dat->axi->axi_blen[a_index] = 128; break; >> + case 6: >> + plat_dat->axi->axi_blen[a_index] = 256; break; >> + default: >> + break; >> + } >> + a_index++; >> + } >> + } >> + >> + /* dwc-qos needs GMAC4, AAL, TSO and PMT */ >> + plat_dat->has_gmac4 = 1; >> + plat_dat->dma_cfg->aal = 1; >> + plat_dat->tso_en = 1; >> + plat_dat->pmt = 1; >> + >> + return 0; >> +} >> + >> +static int dwc_eth_dwmac_probe(struct platform_device *pdev) >> +{ >> + struct plat_stmmacenet_data *plat_dat; >> + struct stmmac_resources stmmac_res; >> + struct resource *res; >> + int ret; >> + >> + /** >> + * Since stmmac_platform supports name IRQ only, basic platform >> + * resource initialization is done in the glue logic. >> + */ >> + stmmac_res.irq = platform_get_irq(pdev, 0); >> + if (stmmac_res.irq < 0) { >> + if (stmmac_res.irq != -EPROBE_DEFER) { >> + dev_err(&pdev->dev, >> + "IRQ configuration information not found\n"); >> + } >> + return stmmac_res.irq; >> + } >> + >> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); >> + stmmac_res.addr = devm_ioremap_resource(&pdev->dev, res); >> + if (IS_ERR(stmmac_res.addr)) >> + return PTR_ERR(stmmac_res.addr); >> + >> + plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); >> + if (IS_ERR(plat_dat)) >> + return PTR_ERR(plat_dat); >> + >> + plat_dat->stmmac_clk = devm_clk_get(&pdev->dev, "phy_ref_clk"); >> + if (IS_ERR(plat_dat->stmmac_clk)) { >> + dev_err(&pdev->dev, "apb_pclk clock not found.\n"); > > Error message does not match the devm_clk_get. > > Looking at synopsys/dwc_eth_qos.c > phy_ref_clk is just a dummy, used for verbosity. > apb_pclk is the clock which is actually used for setting csr etc. > > So it should be > > plat_dat->stmmac_clk = devm_clk_get(&pdev->dev, "apb_pclk"); > > > So that way the warning is already correct :) > > > >> + ret = PTR_ERR(plat_dat->stmmac_clk); >> + plat_dat->stmmac_clk = NULL; >> + goto err_remove_config_dt; >> + } >> + clk_prepare_enable(plat_dat->stmmac_clk); >> + >> + plat_dat->pclk = devm_clk_get(&pdev->dev, "apb_pclk"); >> + if (IS_ERR(plat_dat->pclk)) { >> + dev_err(&pdev->dev, "phy_ref_clk clock not found.\n"); > > Error message does not match the devm_clk_get, > however, since this should be > > plat_dat->pclk = devm_clk_get(&pdev->dev, "phy_ref_clk"); > > the warning is correct :) > >> + ret = PTR_ERR(plat_dat->pclk); >> + plat_dat->pclk = NULL; >> + goto err_out_clk_dis_phy; >> + } >> + clk_prepare_enable(plat_dat->pclk); >> + >> + ret = dwc_eth_dwmac_config_dt(pdev, plat_dat); >> + if (ret) >> + goto err_out_clk_dis_aper; >> + >> + ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res); >> + if (ret) >> + goto err_out_clk_dis_aper; >> + >> + return 0; >> + >> +err_out_clk_dis_aper: >> + clk_disable_unprepare(plat_dat->pclk); >> +err_out_clk_dis_phy: >> + clk_disable_unprepare(plat_dat->stmmac_clk); >> +err_remove_config_dt: >> + stmmac_remove_config_dt(pdev, plat_dat); >> + >> + return ret; >> +} >> + >> +static int dwc_eth_dwmac_remove(struct platform_device *pdev) >> +{ >> + return stmmac_pltfr_remove(pdev); >> +} >> + >> +static const struct of_device_id dwc_eth_dwmac_match[] = { >> + { .compatible = "snps,dwc-qos-ethernet-4.10", }, >> + { } >> +}; >> +MODULE_DEVICE_TABLE(of, dwc_eth_dwmac_match); >> + >> +static struct platform_driver dwc_eth_dwmac_driver = { >> + .probe = dwc_eth_dwmac_probe, >> + .remove = dwc_eth_dwmac_remove, >> + .driver = { >> + .name = "dwc-eth-dwmac", >> + .of_match_table = dwc_eth_dwmac_match, >> + }, >> +}; >> +module_platform_driver(dwc_eth_dwmac_driver); >> + >> +MODULE_AUTHOR("Joao Pinto <jpinto@synopsys.com>"); >> +MODULE_DESCRIPTION("Synopsys DWC Ethernet Quality-of-Service v4.10a driver"); >> +MODULE_LICENSE("GPL v2"); >> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c >> index 4e44f9c..00c0f8d 100644 >> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c >> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c >> @@ -181,10 +181,19 @@ static int stmmac_dt_phy(struct plat_stmmacenet_data *plat, >> mdio = false; >> } >> >> - /* If snps,dwmac-mdio is passed from DT, always register the MDIO */ >> - for_each_child_of_node(np, plat->mdio_node) { >> - if (of_device_is_compatible(plat->mdio_node, "snps,dwmac-mdio")) >> + /* exception for dwmac-dwc-qos-eth glue logic */ >> + if (of_device_is_compatible(np, "snps,dwc-qos-ethernet-4.10")) { >> + plat->mdio_node = of_get_child_by_name(np, "mdio"); >> + } else { >> + /** >> + * If snps,dwmac-mdio is passed from DT, always register >> + * the MDIO >> + */ >> + for_each_child_of_node(np, plat->mdio_node) { >> + if (of_device_is_compatible(plat->mdio_node, >> + "snps,dwmac-mdio")) >> break; >> + } >> } >> >> if (plat->mdio_node) { >
On 01/04/2017 12:08 PM, Joao Pinto wrote: > Hi Niklas, > > Às 10:59 AM de 1/4/2017, Niklas Cassel escreveu: >> Hello Joao >> >> I just tested this series using the dwc_eth_qos DT bindings. >> Good work! >> >> Unfortunately I get the following error: >> >> <3>[ 12.032463] dwc-eth-dwmac f8010000.ethernet eth0: stmmac_open: ERROR: allocating the WoL IRQ -1098801248 (-22) >> >> >> This appears to be because of a corner case in stmmac_platform.c >> where wol_irq can differ from the normal irq. >> >> Adding the following one liner fixes the problem: >> >> >> --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >> @@ -125,6 +125,7 @@ static int dwc_eth_dwmac_probe(struct platform_device *pdev) >> } >> return stmmac_res.irq; >> } >> + stmmac_res.wol_irq = stmmac_res.irq; >> >> res = platform_get_resource(pdev, IORESOURCE_MEM, 0); >> stmmac_res.addr = devm_ioremap_resource(&pdev->dev, res); >> > Ok, I'll add this fix to the patch and give a check to the clks. > I already sent a v1 patch set to net-dev, and I am now going to generate v2 so > it would be great to have your tested.by tag to push it faster :) Thanks! Send your V2, and I will test it, and reply with a Tested-by tag. I can't reply with a Tested-by tag on V1, since it gives an error during open. If I reply with a Tested-by tag, on your V2, patchwork https://patchwork.ozlabs.org/project/netdev/list/ will append it to the patch automatically. Since Dave fetches patches from patchwork, it will be there when it's time to be applied. > >> >> >> I have one comment about clocks interleaved as well >> >> >> >> On 01/04/2017 10:44 AM, Joao Pinto wrote: >>> This patch adds a new glue driver called dwmac-dwc-qos-eth which >>> was based in the dwc_eth_qos as is. To assure retro-compatibility a slight >>> tweak was also added to stmmac_platform. >>> >>> Signed-off-by: Joao Pinto <jpinto@synopsys.com> >>> Reviewed-by: Lars Persson <larper@axis.com> >>> --- >>> .../bindings/net/snps,dwc-qos-ethernet.txt | 3 + >>> drivers/net/ethernet/stmicro/stmmac/Kconfig | 9 + >>> drivers/net/ethernet/stmicro/stmmac/Makefile | 1 + >>> .../ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c | 199 +++++++++++++++++++++ >>> .../net/ethernet/stmicro/stmmac/stmmac_platform.c | 15 +- >>> 5 files changed, 224 insertions(+), 3 deletions(-) >>> create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >>> >>> diff --git a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt >>> index d93f71c..21d27aa 100644 >>> --- a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt >>> +++ b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt >>> @@ -1,5 +1,8 @@ >>> * Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC) >>> >>> +This binding is deprecated, but it continues to be supported, but new >>> +features should be preferably added to the stmmac binding document. >>> + >>> This binding supports the Synopsys Designware Ethernet QoS (Quality Of Service) >>> IP block. The IP supports multiple options for bus type, clocking and reset >>> structure, and feature list. Consequently, a number of properties and list >>> diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig >>> index ab66248..99594e3 100644 >>> --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig >>> +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig >>> @@ -29,6 +29,15 @@ config STMMAC_PLATFORM >>> >>> if STMMAC_PLATFORM >>> >>> +config DWMAC_DWC_QOS_ETH >>> + tristate "Support for snps,dwc-qos-ethernet.txt DT binding." >>> + select PHYLIB >>> + select CRC32 >>> + select MII >>> + depends on OF && HAS_DMA >>> + help >>> + Support for chips using the snps,dwc-qos-ethernet.txt DT binding. >>> + >>> config DWMAC_GENERIC >>> tristate "Generic driver for DWMAC" >>> default STMMAC_PLATFORM >>> diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile >>> index 8f83a86..700c603 100644 >>> --- a/drivers/net/ethernet/stmicro/stmmac/Makefile >>> +++ b/drivers/net/ethernet/stmicro/stmmac/Makefile >>> @@ -16,6 +16,7 @@ obj-$(CONFIG_DWMAC_SOCFPGA) += dwmac-altr-socfpga.o >>> obj-$(CONFIG_DWMAC_STI) += dwmac-sti.o >>> obj-$(CONFIG_DWMAC_STM32) += dwmac-stm32.o >>> obj-$(CONFIG_DWMAC_SUNXI) += dwmac-sunxi.o >>> +obj-$(CONFIG_DWMAC_DWC_QOS_ETH) += dwmac-dwc-qos-eth.o >>> obj-$(CONFIG_DWMAC_GENERIC) += dwmac-generic.o >>> stmmac-platform-objs:= stmmac_platform.o >>> dwmac-altr-socfpga-objs := altr_tse_pcs.o dwmac-socfpga.o >>> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >>> new file mode 100644 >>> index 0000000..8a6ac06 >>> --- /dev/null >>> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >>> @@ -0,0 +1,199 @@ >>> +/* >>> + * Synopsys DWC Ethernet Quality-of-Service v4.10a linux driver >>> + * >>> + * Copyright (C) 2016 Joao Pinto <jpinto@synopsys.com> >>> + * >>> + * This program is free software; you can redistribute it and/or modify >>> + * it under the terms of the GNU General Public License version 2 as >>> + * published by the Free Software Foundation. >>> + * >>> + * You should have received a copy of the GNU General Public License >>> + * along with this program. If not, see <https://urldefense.proofpoint.com/v2/url?u=http-3A__www.gnu.org_licenses_&d=DgIC-g&c=DPL6_X_6JkXFx7AXWqB0tg&r=s2fO0hii0OGNOv9qQy_HRXy-xAJUD1NNoEcc3io_kx0&m=DrobFP08nu4hh6e05EgeOl1xD34OacyiZ-be_GG829Q&s=WLSkpBK06KCu-_kvN305yE6YncNYcDG_Bk0pgqSBG1o&e= >. >>> + */ >>> + >>> +#include <linux/clk.h> >>> +#include <linux/clk-provider.h> >>> +#include <linux/device.h> >>> +#include <linux/ethtool.h> >>> +#include <linux/io.h> >>> +#include <linux/ioport.h> >>> +#include <linux/module.h> >>> +#include <linux/of_net.h> >>> +#include <linux/mfd/syscon.h> >>> +#include <linux/platform_device.h> >>> +#include <linux/stmmac.h> >>> + >>> +#include "stmmac_platform.h" >>> + >>> +static int dwc_eth_dwmac_config_dt(struct platform_device *pdev, >>> + struct plat_stmmacenet_data *plat_dat) >>> +{ >>> + struct device_node *np = pdev->dev.of_node; >>> + u32 burst_map = 0; >>> + u32 bit_index = 0; >>> + u32 a_index = 0; >>> + >>> + if (!plat_dat->axi) { >>> + plat_dat->axi = kzalloc(sizeof(struct stmmac_axi), GFP_KERNEL); >>> + >>> + if (!plat_dat->axi) >>> + return -ENOMEM; >>> + } >>> + >>> + plat_dat->axi->axi_lpi_en = of_property_read_bool(np, "snps,en-lpi"); >>> + if (of_property_read_u32(np, "snps,write-requests", >>> + &plat_dat->axi->axi_wr_osr_lmt)) { >>> + /** >>> + * Since the register has a reset value of 1, if property >>> + * is missing, default to 1. >>> + */ >>> + plat_dat->axi->axi_wr_osr_lmt = 1; >>> + } else { >>> + /** >>> + * If property exists, to keep the behavior from dwc_eth_qos, >>> + * subtract one after parsing. >>> + */ >>> + plat_dat->axi->axi_wr_osr_lmt--; >>> + } >>> + >>> + if (of_property_read_u32(np, "read,read-requests", >>> + &plat_dat->axi->axi_rd_osr_lmt)) { >>> + /** >>> + * Since the register has a reset value of 1, if property >>> + * is missing, default to 1. >>> + */ >>> + plat_dat->axi->axi_rd_osr_lmt = 1; >>> + } else { >>> + /** >>> + * If property exists, to keep the behavior from dwc_eth_qos, >>> + * subtract one after parsing. >>> + */ >>> + plat_dat->axi->axi_rd_osr_lmt--; >>> + } >>> + of_property_read_u32(np, "snps,burst-map", &burst_map); >>> + >>> + /* converts burst-map bitmask to burst array */ >>> + for (bit_index = 0; bit_index < 7; bit_index++) { >>> + if (burst_map & (1 << bit_index)) { >>> + switch (bit_index) { >>> + case 0: >>> + plat_dat->axi->axi_blen[a_index] = 4; break; >>> + case 1: >>> + plat_dat->axi->axi_blen[a_index] = 8; break; >>> + case 2: >>> + plat_dat->axi->axi_blen[a_index] = 16; break; >>> + case 3: >>> + plat_dat->axi->axi_blen[a_index] = 32; break; >>> + case 4: >>> + plat_dat->axi->axi_blen[a_index] = 64; break; >>> + case 5: >>> + plat_dat->axi->axi_blen[a_index] = 128; break; >>> + case 6: >>> + plat_dat->axi->axi_blen[a_index] = 256; break; >>> + default: >>> + break; >>> + } >>> + a_index++; >>> + } >>> + } >>> + >>> + /* dwc-qos needs GMAC4, AAL, TSO and PMT */ >>> + plat_dat->has_gmac4 = 1; >>> + plat_dat->dma_cfg->aal = 1; >>> + plat_dat->tso_en = 1; >>> + plat_dat->pmt = 1; >>> + >>> + return 0; >>> +} >>> + >>> +static int dwc_eth_dwmac_probe(struct platform_device *pdev) >>> +{ >>> + struct plat_stmmacenet_data *plat_dat; >>> + struct stmmac_resources stmmac_res; >>> + struct resource *res; >>> + int ret; >>> + >>> + /** >>> + * Since stmmac_platform supports name IRQ only, basic platform >>> + * resource initialization is done in the glue logic. >>> + */ >>> + stmmac_res.irq = platform_get_irq(pdev, 0); >>> + if (stmmac_res.irq < 0) { >>> + if (stmmac_res.irq != -EPROBE_DEFER) { >>> + dev_err(&pdev->dev, >>> + "IRQ configuration information not found\n"); >>> + } >>> + return stmmac_res.irq; >>> + } >>> + >>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); >>> + stmmac_res.addr = devm_ioremap_resource(&pdev->dev, res); >>> + if (IS_ERR(stmmac_res.addr)) >>> + return PTR_ERR(stmmac_res.addr); >>> + >>> + plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); >>> + if (IS_ERR(plat_dat)) >>> + return PTR_ERR(plat_dat); >>> + >>> + plat_dat->stmmac_clk = devm_clk_get(&pdev->dev, "phy_ref_clk"); >>> + if (IS_ERR(plat_dat->stmmac_clk)) { >>> + dev_err(&pdev->dev, "apb_pclk clock not found.\n"); >> Error message does not match the devm_clk_get. >> >> Looking at synopsys/dwc_eth_qos.c >> phy_ref_clk is just a dummy, used for verbosity. >> apb_pclk is the clock which is actually used for setting csr etc. >> >> So it should be >> >> plat_dat->stmmac_clk = devm_clk_get(&pdev->dev, "apb_pclk"); >> >> >> So that way the warning is already correct :) >> >> >> >>> + ret = PTR_ERR(plat_dat->stmmac_clk); >>> + plat_dat->stmmac_clk = NULL; >>> + goto err_remove_config_dt; >>> + } >>> + clk_prepare_enable(plat_dat->stmmac_clk); >>> + >>> + plat_dat->pclk = devm_clk_get(&pdev->dev, "apb_pclk"); >>> + if (IS_ERR(plat_dat->pclk)) { >>> + dev_err(&pdev->dev, "phy_ref_clk clock not found.\n"); >> Error message does not match the devm_clk_get, >> however, since this should be >> >> plat_dat->pclk = devm_clk_get(&pdev->dev, "phy_ref_clk"); >> >> the warning is correct :) >> >>> + ret = PTR_ERR(plat_dat->pclk); >>> + plat_dat->pclk = NULL; >>> + goto err_out_clk_dis_phy; >>> + } >>> + clk_prepare_enable(plat_dat->pclk); >>> + >>> + ret = dwc_eth_dwmac_config_dt(pdev, plat_dat); >>> + if (ret) >>> + goto err_out_clk_dis_aper; >>> + >>> + ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res); >>> + if (ret) >>> + goto err_out_clk_dis_aper; >>> + >>> + return 0; >>> + >>> +err_out_clk_dis_aper: >>> + clk_disable_unprepare(plat_dat->pclk); >>> +err_out_clk_dis_phy: >>> + clk_disable_unprepare(plat_dat->stmmac_clk); >>> +err_remove_config_dt: >>> + stmmac_remove_config_dt(pdev, plat_dat); >>> + >>> + return ret; >>> +} >>> + >>> +static int dwc_eth_dwmac_remove(struct platform_device *pdev) >>> +{ >>> + return stmmac_pltfr_remove(pdev); >>> +} >>> + >>> +static const struct of_device_id dwc_eth_dwmac_match[] = { >>> + { .compatible = "snps,dwc-qos-ethernet-4.10", }, >>> + { } >>> +}; >>> +MODULE_DEVICE_TABLE(of, dwc_eth_dwmac_match); >>> + >>> +static struct platform_driver dwc_eth_dwmac_driver = { >>> + .probe = dwc_eth_dwmac_probe, >>> + .remove = dwc_eth_dwmac_remove, >>> + .driver = { >>> + .name = "dwc-eth-dwmac", >>> + .of_match_table = dwc_eth_dwmac_match, >>> + }, >>> +}; >>> +module_platform_driver(dwc_eth_dwmac_driver); >>> + >>> +MODULE_AUTHOR("Joao Pinto <jpinto@synopsys.com>"); >>> +MODULE_DESCRIPTION("Synopsys DWC Ethernet Quality-of-Service v4.10a driver"); >>> +MODULE_LICENSE("GPL v2"); >>> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c >>> index 4e44f9c..00c0f8d 100644 >>> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c >>> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c >>> @@ -181,10 +181,19 @@ static int stmmac_dt_phy(struct plat_stmmacenet_data *plat, >>> mdio = false; >>> } >>> >>> - /* If snps,dwmac-mdio is passed from DT, always register the MDIO */ >>> - for_each_child_of_node(np, plat->mdio_node) { >>> - if (of_device_is_compatible(plat->mdio_node, "snps,dwmac-mdio")) >>> + /* exception for dwmac-dwc-qos-eth glue logic */ >>> + if (of_device_is_compatible(np, "snps,dwc-qos-ethernet-4.10")) { >>> + plat->mdio_node = of_get_child_by_name(np, "mdio"); >>> + } else { >>> + /** >>> + * If snps,dwmac-mdio is passed from DT, always register >>> + * the MDIO >>> + */ >>> + for_each_child_of_node(np, plat->mdio_node) { >>> + if (of_device_is_compatible(plat->mdio_node, >>> + "snps,dwmac-mdio")) >>> break; >>> + } >>> } >>> >>> if (plat->mdio_node) {
Às 11:24 AM de 1/4/2017, Niklas Cassel escreveu: > > > On 01/04/2017 12:08 PM, Joao Pinto wrote: >> Hi Niklas, >> >> Às 10:59 AM de 1/4/2017, Niklas Cassel escreveu: >>> Hello Joao >>> >>> I just tested this series using the dwc_eth_qos DT bindings. >>> Good work! >>> >>> Unfortunately I get the following error: >>> >>> <3>[ 12.032463] dwc-eth-dwmac f8010000.ethernet eth0: stmmac_open: ERROR: allocating the WoL IRQ -1098801248 (-22) >>> >>> >>> This appears to be because of a corner case in stmmac_platform.c >>> where wol_irq can differ from the normal irq. >>> >>> Adding the following one liner fixes the problem: >>> >>> >>> --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >>> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >>> @@ -125,6 +125,7 @@ static int dwc_eth_dwmac_probe(struct platform_device *pdev) >>> } >>> return stmmac_res.irq; >>> } >>> + stmmac_res.wol_irq = stmmac_res.irq; >>> >>> res = platform_get_resource(pdev, IORESOURCE_MEM, 0); >>> stmmac_res.addr = devm_ioremap_resource(&pdev->dev, res); >>> >> Ok, I'll add this fix to the patch and give a check to the clks. >> I already sent a v1 patch set to net-dev, and I am now going to generate v2 so >> it would be great to have your tested.by tag to push it faster :) Thanks! > > Send your V2, and I will test it, and reply with a Tested-by tag. > I can't reply with a Tested-by tag on V1, since it gives an > error during open. > > If I reply with a Tested-by tag, on your V2, patchwork > https://urldefense.proofpoint.com/v2/url?u=https-3A__patchwork.ozlabs.org_project_netdev_list_&d=DgID-g&c=DPL6_X_6JkXFx7AXWqB0tg&r=s2fO0hii0OGNOv9qQy_HRXy-xAJUD1NNoEcc3io_kx0&m=Ne_JFvbqIwFj_Tokwm6Yv1pv3wETnoD3iG7TjxJqLaQ&s=7hU48UexRw1mb7Y3V4ly3tX0yErTXUW_k4gSZVGe4yE&e= > will append it to the patch automatically. > Since Dave fetches patches from patchwork, > it will be there when it's time to be applied. Ok, great! Just sent you v2. Thanks. > >> >>> >>> >>> I have one comment about clocks interleaved as well >>> >>> >>> >>> On 01/04/2017 10:44 AM, Joao Pinto wrote: >>>> This patch adds a new glue driver called dwmac-dwc-qos-eth which >>>> was based in the dwc_eth_qos as is. To assure retro-compatibility a slight >>>> tweak was also added to stmmac_platform. >>>> >>>> Signed-off-by: Joao Pinto <jpinto@synopsys.com> >>>> Reviewed-by: Lars Persson <larper@axis.com> >>>> --- >>>> .../bindings/net/snps,dwc-qos-ethernet.txt | 3 + >>>> drivers/net/ethernet/stmicro/stmmac/Kconfig | 9 + >>>> drivers/net/ethernet/stmicro/stmmac/Makefile | 1 + >>>> .../ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c | 199 +++++++++++++++++++++ >>>> .../net/ethernet/stmicro/stmmac/stmmac_platform.c | 15 +- >>>> 5 files changed, 224 insertions(+), 3 deletions(-) >>>> create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >>>> >>>> diff --git a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt >>>> index d93f71c..21d27aa 100644 >>>> --- a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt >>>> +++ b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt >>>> @@ -1,5 +1,8 @@ >>>> * Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC) >>>> >>>> +This binding is deprecated, but it continues to be supported, but new >>>> +features should be preferably added to the stmmac binding document. >>>> + >>>> This binding supports the Synopsys Designware Ethernet QoS (Quality Of Service) >>>> IP block. The IP supports multiple options for bus type, clocking and reset >>>> structure, and feature list. Consequently, a number of properties and list >>>> diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig >>>> index ab66248..99594e3 100644 >>>> --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig >>>> +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig >>>> @@ -29,6 +29,15 @@ config STMMAC_PLATFORM >>>> >>>> if STMMAC_PLATFORM >>>> >>>> +config DWMAC_DWC_QOS_ETH >>>> + tristate "Support for snps,dwc-qos-ethernet.txt DT binding." >>>> + select PHYLIB >>>> + select CRC32 >>>> + select MII >>>> + depends on OF && HAS_DMA >>>> + help >>>> + Support for chips using the snps,dwc-qos-ethernet.txt DT binding. >>>> + >>>> config DWMAC_GENERIC >>>> tristate "Generic driver for DWMAC" >>>> default STMMAC_PLATFORM >>>> diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile >>>> index 8f83a86..700c603 100644 >>>> --- a/drivers/net/ethernet/stmicro/stmmac/Makefile >>>> +++ b/drivers/net/ethernet/stmicro/stmmac/Makefile >>>> @@ -16,6 +16,7 @@ obj-$(CONFIG_DWMAC_SOCFPGA) += dwmac-altr-socfpga.o >>>> obj-$(CONFIG_DWMAC_STI) += dwmac-sti.o >>>> obj-$(CONFIG_DWMAC_STM32) += dwmac-stm32.o >>>> obj-$(CONFIG_DWMAC_SUNXI) += dwmac-sunxi.o >>>> +obj-$(CONFIG_DWMAC_DWC_QOS_ETH) += dwmac-dwc-qos-eth.o >>>> obj-$(CONFIG_DWMAC_GENERIC) += dwmac-generic.o >>>> stmmac-platform-objs:= stmmac_platform.o >>>> dwmac-altr-socfpga-objs := altr_tse_pcs.o dwmac-socfpga.o >>>> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >>>> new file mode 100644 >>>> index 0000000..8a6ac06 >>>> --- /dev/null >>>> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c >>>> @@ -0,0 +1,199 @@ >>>> +/* >>>> + * Synopsys DWC Ethernet Quality-of-Service v4.10a linux driver >>>> + * >>>> + * Copyright (C) 2016 Joao Pinto <jpinto@synopsys.com> >>>> + * >>>> + * This program is free software; you can redistribute it and/or modify >>>> + * it under the terms of the GNU General Public License version 2 as >>>> + * published by the Free Software Foundation. >>>> + * >>>> + * You should have received a copy of the GNU General Public License >>>> + * along with this program. If not, see <https://urldefense.proofpoint.com/v2/url?u=http-3A__www.gnu.org_licenses_&d=DgIC-g&c=DPL6_X_6JkXFx7AXWqB0tg&r=s2fO0hii0OGNOv9qQy_HRXy-xAJUD1NNoEcc3io_kx0&m=DrobFP08nu4hh6e05EgeOl1xD34OacyiZ-be_GG829Q&s=WLSkpBK06KCu-_kvN305yE6YncNYcDG_Bk0pgqSBG1o&e=>. >>>> + */ >>>> + >>>> +#include <linux/clk.h> >>>> +#include <linux/clk-provider.h> >>>> +#include <linux/device.h> >>>> +#include <linux/ethtool.h> >>>> +#include <linux/io.h> >>>> +#include <linux/ioport.h> >>>> +#include <linux/module.h> >>>> +#include <linux/of_net.h> >>>> +#include <linux/mfd/syscon.h> >>>> +#include <linux/platform_device.h> >>>> +#include <linux/stmmac.h> >>>> + >>>> +#include "stmmac_platform.h" >>>> + >>>> +static int dwc_eth_dwmac_config_dt(struct platform_device *pdev, >>>> + struct plat_stmmacenet_data *plat_dat) >>>> +{ >>>> + struct device_node *np = pdev->dev.of_node; >>>> + u32 burst_map = 0; >>>> + u32 bit_index = 0; >>>> + u32 a_index = 0; >>>> + >>>> + if (!plat_dat->axi) { >>>> + plat_dat->axi = kzalloc(sizeof(struct stmmac_axi), GFP_KERNEL); >>>> + >>>> + if (!plat_dat->axi) >>>> + return -ENOMEM; >>>> + } >>>> + >>>> + plat_dat->axi->axi_lpi_en = of_property_read_bool(np, "snps,en-lpi"); >>>> + if (of_property_read_u32(np, "snps,write-requests", >>>> + &plat_dat->axi->axi_wr_osr_lmt)) { >>>> + /** >>>> + * Since the register has a reset value of 1, if property >>>> + * is missing, default to 1. >>>> + */ >>>> + plat_dat->axi->axi_wr_osr_lmt = 1; >>>> + } else { >>>> + /** >>>> + * If property exists, to keep the behavior from dwc_eth_qos, >>>> + * subtract one after parsing. >>>> + */ >>>> + plat_dat->axi->axi_wr_osr_lmt--; >>>> + } >>>> + >>>> + if (of_property_read_u32(np, "read,read-requests", >>>> + &plat_dat->axi->axi_rd_osr_lmt)) { >>>> + /** >>>> + * Since the register has a reset value of 1, if property >>>> + * is missing, default to 1. >>>> + */ >>>> + plat_dat->axi->axi_rd_osr_lmt = 1; >>>> + } else { >>>> + /** >>>> + * If property exists, to keep the behavior from dwc_eth_qos, >>>> + * subtract one after parsing. >>>> + */ >>>> + plat_dat->axi->axi_rd_osr_lmt--; >>>> + } >>>> + of_property_read_u32(np, "snps,burst-map", &burst_map); >>>> + >>>> + /* converts burst-map bitmask to burst array */ >>>> + for (bit_index = 0; bit_index < 7; bit_index++) { >>>> + if (burst_map & (1 << bit_index)) { >>>> + switch (bit_index) { >>>> + case 0: >>>> + plat_dat->axi->axi_blen[a_index] = 4; break; >>>> + case 1: >>>> + plat_dat->axi->axi_blen[a_index] = 8; break; >>>> + case 2: >>>> + plat_dat->axi->axi_blen[a_index] = 16; break; >>>> + case 3: >>>> + plat_dat->axi->axi_blen[a_index] = 32; break; >>>> + case 4: >>>> + plat_dat->axi->axi_blen[a_index] = 64; break; >>>> + case 5: >>>> + plat_dat->axi->axi_blen[a_index] = 128; break; >>>> + case 6: >>>> + plat_dat->axi->axi_blen[a_index] = 256; break; >>>> + default: >>>> + break; >>>> + } >>>> + a_index++; >>>> + } >>>> + } >>>> + >>>> + /* dwc-qos needs GMAC4, AAL, TSO and PMT */ >>>> + plat_dat->has_gmac4 = 1; >>>> + plat_dat->dma_cfg->aal = 1; >>>> + plat_dat->tso_en = 1; >>>> + plat_dat->pmt = 1; >>>> + >>>> + return 0; >>>> +} >>>> + >>>> +static int dwc_eth_dwmac_probe(struct platform_device *pdev) >>>> +{ >>>> + struct plat_stmmacenet_data *plat_dat; >>>> + struct stmmac_resources stmmac_res; >>>> + struct resource *res; >>>> + int ret; >>>> + >>>> + /** >>>> + * Since stmmac_platform supports name IRQ only, basic platform >>>> + * resource initialization is done in the glue logic. >>>> + */ >>>> + stmmac_res.irq = platform_get_irq(pdev, 0); >>>> + if (stmmac_res.irq < 0) { >>>> + if (stmmac_res.irq != -EPROBE_DEFER) { >>>> + dev_err(&pdev->dev, >>>> + "IRQ configuration information not found\n"); >>>> + } >>>> + return stmmac_res.irq; >>>> + } >>>> + >>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); >>>> + stmmac_res.addr = devm_ioremap_resource(&pdev->dev, res); >>>> + if (IS_ERR(stmmac_res.addr)) >>>> + return PTR_ERR(stmmac_res.addr); >>>> + >>>> + plat_dat = stmmac_probe_config_dt(pdev, &stmmac_res.mac); >>>> + if (IS_ERR(plat_dat)) >>>> + return PTR_ERR(plat_dat); >>>> + >>>> + plat_dat->stmmac_clk = devm_clk_get(&pdev->dev, "phy_ref_clk"); >>>> + if (IS_ERR(plat_dat->stmmac_clk)) { >>>> + dev_err(&pdev->dev, "apb_pclk clock not found.\n"); >>> Error message does not match the devm_clk_get. >>> >>> Looking at synopsys/dwc_eth_qos.c >>> phy_ref_clk is just a dummy, used for verbosity. >>> apb_pclk is the clock which is actually used for setting csr etc. >>> >>> So it should be >>> >>> plat_dat->stmmac_clk = devm_clk_get(&pdev->dev, "apb_pclk"); >>> >>> >>> So that way the warning is already correct :) >>> >>> >>> >>>> + ret = PTR_ERR(plat_dat->stmmac_clk); >>>> + plat_dat->stmmac_clk = NULL; >>>> + goto err_remove_config_dt; >>>> + } >>>> + clk_prepare_enable(plat_dat->stmmac_clk); >>>> + >>>> + plat_dat->pclk = devm_clk_get(&pdev->dev, "apb_pclk"); >>>> + if (IS_ERR(plat_dat->pclk)) { >>>> + dev_err(&pdev->dev, "phy_ref_clk clock not found.\n"); >>> Error message does not match the devm_clk_get, >>> however, since this should be >>> >>> plat_dat->pclk = devm_clk_get(&pdev->dev, "phy_ref_clk"); >>> >>> the warning is correct :) >>> >>>> + ret = PTR_ERR(plat_dat->pclk); >>>> + plat_dat->pclk = NULL; >>>> + goto err_out_clk_dis_phy; >>>> + } >>>> + clk_prepare_enable(plat_dat->pclk); >>>> + >>>> + ret = dwc_eth_dwmac_config_dt(pdev, plat_dat); >>>> + if (ret) >>>> + goto err_out_clk_dis_aper; >>>> + >>>> + ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res); >>>> + if (ret) >>>> + goto err_out_clk_dis_aper; >>>> + >>>> + return 0; >>>> + >>>> +err_out_clk_dis_aper: >>>> + clk_disable_unprepare(plat_dat->pclk); >>>> +err_out_clk_dis_phy: >>>> + clk_disable_unprepare(plat_dat->stmmac_clk); >>>> +err_remove_config_dt: >>>> + stmmac_remove_config_dt(pdev, plat_dat); >>>> + >>>> + return ret; >>>> +} >>>> + >>>> +static int dwc_eth_dwmac_remove(struct platform_device *pdev) >>>> +{ >>>> + return stmmac_pltfr_remove(pdev); >>>> +} >>>> + >>>> +static const struct of_device_id dwc_eth_dwmac_match[] = { >>>> + { .compatible = "snps,dwc-qos-ethernet-4.10", }, >>>> + { } >>>> +}; >>>> +MODULE_DEVICE_TABLE(of, dwc_eth_dwmac_match); >>>> + >>>> +static struct platform_driver dwc_eth_dwmac_driver = { >>>> + .probe = dwc_eth_dwmac_probe, >>>> + .remove = dwc_eth_dwmac_remove, >>>> + .driver = { >>>> + .name = "dwc-eth-dwmac", >>>> + .of_match_table = dwc_eth_dwmac_match, >>>> + }, >>>> +}; >>>> +module_platform_driver(dwc_eth_dwmac_driver); >>>> + >>>> +MODULE_AUTHOR("Joao Pinto <jpinto@synopsys.com>"); >>>> +MODULE_DESCRIPTION("Synopsys DWC Ethernet Quality-of-Service v4.10a driver"); >>>> +MODULE_LICENSE("GPL v2"); >>>> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c >>>> index 4e44f9c..00c0f8d 100644 >>>> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c >>>> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c >>>> @@ -181,10 +181,19 @@ static int stmmac_dt_phy(struct plat_stmmacenet_data *plat, >>>> mdio = false; >>>> } >>>> >>>> - /* If snps,dwmac-mdio is passed from DT, always register the MDIO */ >>>> - for_each_child_of_node(np, plat->mdio_node) { >>>> - if (of_device_is_compatible(plat->mdio_node, "snps,dwmac-mdio")) >>>> + /* exception for dwmac-dwc-qos-eth glue logic */ >>>> + if (of_device_is_compatible(np, "snps,dwc-qos-ethernet-4.10")) { >>>> + plat->mdio_node = of_get_child_by_name(np, "mdio"); >>>> + } else { >>>> + /** >>>> + * If snps,dwmac-mdio is passed from DT, always register >>>> + * the MDIO >>>> + */ >>>> + for_each_child_of_node(np, plat->mdio_node) { >>>> + if (of_device_is_compatible(plat->mdio_node, >>>> + "snps,dwmac-mdio")) >>>> break; >>>> + } >>>> } >>>> >>>> if (plat->mdio_node) { >
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-dwc-qos-eth.c @@ -125,6 +125,7 @@ static int dwc_eth_dwmac_probe(struct platform_device *pdev) } return stmmac_res.irq; } + stmmac_res.wol_irq = stmmac_res.irq; res = platform_get_resource(pdev, IORESOURCE_MEM, 0); stmmac_res.addr = devm_ioremap_resource(&pdev->dev, res);