[v2,2/2] net: ethernet: nb8800: handle all RGMII definitions

Commit a999589ccaae ("phylib: add RGMII-ID interface mode definition")
and commit 7d400a4c5897 ("phylib: add PHY interface modes for internal
delay for tx and rx only") added several RGMII definitions:
PHY_INTERFACE_MODE_RGMII_ID, PHY_INTERFACE_MODE_RGMII_RXID and
PHY_INTERFACE_MODE_RGMII_TXID to deal with internal delays.

Those are all RGMII modes (1Gbit) and must be considered that way when
setting the MAC mode or the pad mode for the HW to work properly.

Signed-off-by: Sebastian Frias <sf84@laposte.net>
---
 drivers/net/ethernet/aurora/nb8800.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

Sebastian Frias <sf84@laposte.net> writes:

> Commit a999589ccaae ("phylib: add RGMII-ID interface mode definition")
> and commit 7d400a4c5897 ("phylib: add PHY interface modes for internal
> delay for tx and rx only") added several RGMII definitions:
> PHY_INTERFACE_MODE_RGMII_ID, PHY_INTERFACE_MODE_RGMII_RXID and
> PHY_INTERFACE_MODE_RGMII_TXID to deal with internal delays.
>
> Those are all RGMII modes (1Gbit) and must be considered that way when
> setting the MAC mode or the pad mode for the HW to work properly.
>
> Signed-off-by: Sebastian Frias <sf84@laposte.net>
> ---
>  drivers/net/ethernet/aurora/nb8800.c | 8 ++++----
>  1 file changed, 4 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/net/ethernet/aurora/nb8800.c b/drivers/net/ethernet/aurora/nb8800.c
> index d2855c9..fba2699 100644
> --- a/drivers/net/ethernet/aurora/nb8800.c
> +++ b/drivers/net/ethernet/aurora/nb8800.c
> @@ -598,6 +598,7 @@ static irqreturn_t nb8800_irq(int irq, void *dev_id)
>  static void nb8800_mac_config(struct net_device *dev)
>  {
>  	struct nb8800_priv *priv = netdev_priv(dev);
> +	struct phy_device *phydev = dev->phydev;
>  	bool gigabit = priv->speed == SPEED_1000;
>  	u32 mac_mode_mask = RGMII_MODE | HALF_DUPLEX | GMAC_MODE;
>  	u32 mac_mode = 0;
> @@ -609,7 +610,7 @@ static void nb8800_mac_config(struct net_device *dev)
>  		mac_mode |= HALF_DUPLEX;
>
>  	if (gigabit) {
> -		if (priv->phy_mode == PHY_INTERFACE_MODE_RGMII)
> +		if (phy_interface_is_rgmii(phydev))
>  			mac_mode |= RGMII_MODE;
>
>  		mac_mode |= GMAC_MODE;

This part is correct regardless of the outcome of the delay setup
discussion.

> @@ -1278,9 +1279,8 @@ static int nb8800_tangox_init(struct net_device *dev)
>  		break;
>
>  	case PHY_INTERFACE_MODE_RGMII:
> -		pad_mode = PAD_MODE_RGMII;
> -		break;
> -
> +	case PHY_INTERFACE_MODE_RGMII_ID:
> +	case PHY_INTERFACE_MODE_RGMII_RXID:
>  	case PHY_INTERFACE_MODE_RGMII_TXID:
>  		pad_mode = PAD_MODE_RGMII;
>  		break;
> -- 
> 1.7.11.2
>

From: Sebastian Frias <sf84@laposte.net>
Date: Fri, 4 Nov 2016 18:02:15 +0100

> Commit a999589ccaae ("phylib: add RGMII-ID interface mode definition")
> and commit 7d400a4c5897 ("phylib: add PHY interface modes for internal
> delay for tx and rx only") added several RGMII definitions:
> PHY_INTERFACE_MODE_RGMII_ID, PHY_INTERFACE_MODE_RGMII_RXID and
> PHY_INTERFACE_MODE_RGMII_TXID to deal with internal delays.
> 
> Those are all RGMII modes (1Gbit) and must be considered that way when
> setting the MAC mode or the pad mode for the HW to work properly.
> 
> Signed-off-by: Sebastian Frias <sf84@laposte.net>

You cannot just repost one part of a patch series when you make changes.

You must always repost the entire series as a new fresh version, with
changelog entries added to your "[PATCH v2 0/2] ..." header posting.

Hi David,

On 11/04/2016 06:54 PM, David Miller wrote:
> From: Sebastian Frias <sf84@laposte.net>
> Date: Fri, 4 Nov 2016 18:02:15 +0100
> 
>> Commit a999589ccaae ("phylib: add RGMII-ID interface mode definition")
>> and commit 7d400a4c5897 ("phylib: add PHY interface modes for internal
>> delay for tx and rx only") added several RGMII definitions:
>> PHY_INTERFACE_MODE_RGMII_ID, PHY_INTERFACE_MODE_RGMII_RXID and
>> PHY_INTERFACE_MODE_RGMII_TXID to deal with internal delays.
>>
>> Those are all RGMII modes (1Gbit) and must be considered that way when
>> setting the MAC mode or the pad mode for the HW to work properly.
>>
>> Signed-off-by: Sebastian Frias <sf84@laposte.net>
> 
> You cannot just repost one part of a patch series when you make changes.
> 
> You must always repost the entire series as a new fresh version, with
> changelog entries added to your "[PATCH v2 0/2] ..." header posting.
> 

Thanks for the information.

I sent v2, and then v3, because v2 had formatting issues, hopefully it is
ok now.

Best regards,

Sebastian