diff mbox

[LEDE-DEV,ramips] Added NixCore X1 target V3

Message ID 5759C4EB.5080203@nixcores.com
State Changes Requested
Headers show

Commit Message

Drew from NixCore June 9, 2016, 7:35 p.m. UTC 
Added NixCore X1 ramips target http://nixcores.com. This builds 8M and 
16M images.  V3 updates the dts to support LEDE updated format

Signed-off-by: Drew Gaylo <drew at nixcores.com>

Comments

Karl Palsson June 9, 2016, 9:12 p.m. UTC | #1 
If the 8 and 16 meg files only differ in their memory, should
they perhaps just have a common .dtsi file for them both? instead
of duplicating the entire dts? I've snipped the only differences
between them below...

Sincerely,
Karl P


Drew from NixCore <drew@nixcores.com> wrote:
> Added NixCore X1 ramips target http://nixcores.com. This builds
> 8M and 16M images. V3 updates the dts to support LEDE updated
> format
> 
> Signed-off-by: Drew Gaylo <drew at nixcores.com>
> diff --git
> diff --git a/target/linux/ramips/dts/NIXCOREX1-16M.dts
> b/target/linux/ramips/dts/NIXCOREX1-16M.dts new file mode
> 100644 index 0000000..1e1a205
> --- /dev/null
> +++ b/target/linux/ramips/dts/NIXCOREX1-16M.dts
snip

> +        partition@50000 {
> +            label = "firmware";
> +            reg = <0x50000 0xfb0000>;
> +        };
> +    };
> +};
> +

> diff --git a/target/linux/ramips/dts/NIXCOREX1-8M.dts
> b/target/linux/ramips/dts/NIXCOREX1-8M.dts new file mode 100644
> index 0000000..c514860
> --- /dev/null
> +++ b/target/linux/ramips/dts/NIXCOREX1-8M.dts
snip 

> +        partition@50000 {
> +            label = "firmware";
> +            reg = <0x50000 0x7b0000>;
> +        };
> +    };
> +};
> +
Drew from NixCore June 9, 2016, 9:36 p.m. UTC | #2 
I have no problem with a common dtsi, can I get these changes in first 
and then do the dtsi as I continue work?

Drew

On 06/09/2016 03:12 PM, Karl Palsson wrote:
> If the 8 and 16 meg files only differ in their memory, should
> they perhaps just have a common .dtsi file for them both? instead
> of duplicating the entire dts? I've snipped the only differences
> between them below...
>
> Sincerely,
> Karl P
>
>
> Drew from NixCore <drew@nixcores.com> wrote:
>> Added NixCore X1 ramips target http://nixcores.com. This builds
>> 8M and 16M images. V3 updates the dts to support LEDE updated
>> format
>>
>> Signed-off-by: Drew Gaylo <drew at nixcores.com>
>> diff --git
>> diff --git a/target/linux/ramips/dts/NIXCOREX1-16M.dts
>> b/target/linux/ramips/dts/NIXCOREX1-16M.dts new file mode
>> 100644 index 0000000..1e1a205
>> --- /dev/null
>> +++ b/target/linux/ramips/dts/NIXCOREX1-16M.dts
> snip
>
>> +        partition@50000 {
>> +            label = "firmware";
>> +            reg = <0x50000 0xfb0000>;
>> +        };
>> +    };
>> +};
>> +
>> diff --git a/target/linux/ramips/dts/NIXCOREX1-8M.dts
>> b/target/linux/ramips/dts/NIXCOREX1-8M.dts new file mode 100644
>> index 0000000..c514860
>> --- /dev/null
>> +++ b/target/linux/ramips/dts/NIXCOREX1-8M.dts
> snip
>
>> +        partition@50000 {
>> +            label = "firmware";
>> +            reg = <0x50000 0x7b0000>;
>> +        };
>> +    };
>> +};
>> +
>>
>>
>> _______________________________________________
>> Lede-dev mailing list
>> Lede-dev@lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/lede-dev
John Crispin June 10, 2016, 6:38 a.m. UTC | #3 
On 09/06/2016 23:36, Drew from NixCore wrote:
> I have no problem with a common dtsi, can I get these changes in first
> and then do the dtsi as I continue work?
> 
> Drew
> 
> On 06/09/2016 03:12 PM, Karl Palsson wrote:
>> If the 8 and 16 meg files only differ in their memory, should
>> they perhaps just have a common .dtsi file for them both? instead
>> of duplicating the entire dts? I've snipped the only differences
>> between them below...
>>
>> Sincerely,
>> Karl P
>>
>>
>> Drew from NixCore <drew@nixcores.com> wrote:
>>> Added NixCore X1 ramips target http://nixcores.com. This builds
>>> 8M and 16M images. V3 updates the dts to support LEDE updated
>>> format

Hi Drew,

i just wanted to fix the dtsi stuff myself however the patch is
whitespace broken and does not apply. i went on to manually fix the
whitespace breakage to find that you did not generate this patch against
our latest source.git and that it wont apply.

which tree at what rev did you use to generate the patch ?

	John








>>>
>>> Signed-off-by: Drew Gaylo <drew at nixcores.com>
>>> diff --git
>>> diff --git a/target/linux/ramips/dts/NIXCOREX1-16M.dts
>>> b/target/linux/ramips/dts/NIXCOREX1-16M.dts new file mode
>>> 100644 index 0000000..1e1a205
>>> --- /dev/null
>>> +++ b/target/linux/ramips/dts/NIXCOREX1-16M.dts
>> snip
>>
>>> +        partition@50000 {
>>> +            label = "firmware";
>>> +            reg = <0x50000 0xfb0000>;
>>> +        };
>>> +    };
>>> +};
>>> +
>>> diff --git a/target/linux/ramips/dts/NIXCOREX1-8M.dts
>>> b/target/linux/ramips/dts/NIXCOREX1-8M.dts new file mode 100644
>>> index 0000000..c514860
>>> --- /dev/null
>>> +++ b/target/linux/ramips/dts/NIXCOREX1-8M.dts
>> snip
>>
>>> +        partition@50000 {
>>> +            label = "firmware";
>>> +            reg = <0x50000 0x7b0000>;
>>> +        };
>>> +    };
>>> +};
>>> +
>>>
>>>
>>> _______________________________________________
>>> Lede-dev mailing list
>>> Lede-dev@lists.infradead.org
>>> http://lists.infradead.org/mailman/listinfo/lede-dev
> 
> 
> _______________________________________________
> Lede-dev mailing list
> Lede-dev@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/lede-dev
Drew from NixCore June 14, 2016, 6:56 p.m. UTC | #4 
John,

I originally was working on a git clone of the repo master branch from 
June 5th.  https://github.com/nixcore/lede-fork1 Rather than do a git 
pull request I just generated the patch for the mailing list. I've 
applied the same patch (via git apply) to the current HEAD of source.git 
repo and while there appear to be some whitespace warnings the patch 
applies correctly from the .patch file.  Maybe the formatting got messed 
up in the submit.

Drew

On 06/10/2016 02:38 AM, John Crispin wrote:
>
> On 09/06/2016 23:36, Drew from NixCore wrote:
>> I have no problem with a common dtsi, can I get these changes in first
>> and then do the dtsi as I continue work?
>>
>> Drew
>>
>> On 06/09/2016 03:12 PM, Karl Palsson wrote:
>>> If the 8 and 16 meg files only differ in their memory, should
>>> they perhaps just have a common .dtsi file for them both? instead
>>> of duplicating the entire dts? I've snipped the only differences
>>> between them below...
>>>
>>> Sincerely,
>>> Karl P
>>>
>>>
>>> Drew from NixCore <drew@nixcores.com> wrote:
>>>> Added NixCore X1 ramips target http://nixcores.com. This builds
>>>> 8M and 16M images. V3 updates the dts to support LEDE updated
>>>> format
> Hi Drew,
>
> i just wanted to fix the dtsi stuff myself however the patch is
> whitespace broken and does not apply. i went on to manually fix the
> whitespace breakage to find that you did not generate this patch against
> our latest source.git and that it wont apply.
>
> which tree at what rev did you use to generate the patch ?
>
> 	John
>
>
>
>
>
>
>
>
>>>> Signed-off-by: Drew Gaylo <drew at nixcores.com>
>>>> diff --git
>>>> diff --git a/target/linux/ramips/dts/NIXCOREX1-16M.dts
>>>> b/target/linux/ramips/dts/NIXCOREX1-16M.dts new file mode
>>>> 100644 index 0000000..1e1a205
>>>> --- /dev/null
>>>> +++ b/target/linux/ramips/dts/NIXCOREX1-16M.dts
>>> snip
>>>
>>>> +        partition@50000 {
>>>> +            label = "firmware";
>>>> +            reg = <0x50000 0xfb0000>;
>>>> +        };
>>>> +    };
>>>> +};
>>>> +
>>>> diff --git a/target/linux/ramips/dts/NIXCOREX1-8M.dts
>>>> b/target/linux/ramips/dts/NIXCOREX1-8M.dts new file mode 100644
>>>> index 0000000..c514860
>>>> --- /dev/null
>>>> +++ b/target/linux/ramips/dts/NIXCOREX1-8M.dts
>>> snip
>>>
>>>> +        partition@50000 {
>>>> +            label = "firmware";
>>>> +            reg = <0x50000 0x7b0000>;
>>>> +        };
>>>> +    };
>>>> +};
>>>> +
>>>>
>>>>
>>>> _______________________________________________
>>>> Lede-dev mailing list
>>>> Lede-dev@lists.infradead.org
>>>> http://lists.infradead.org/mailman/listinfo/lede-dev
>>
>> _______________________________________________
>> Lede-dev mailing list
>> Lede-dev@lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/lede-dev
> _______________________________________________
> Lede-dev mailing list
> Lede-dev@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/lede-dev
diff mbox

Patch

diff --git a/target/linux/ramips/base-files/etc/board.d/02_network 
b/target/linux/ramips/base-files/etc/board.d/02_network
index 4728c75..69c0125 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -77,6 +77,7 @@  ramips_setup_interfaces()
      mt7628|\
      mzk-750dhp|\
      mzk-w300nh2|\
+    nixcore|\
      oy-0001|\
      pbr-m1|\
      psg1208|\
diff --git a/target/linux/ramips/base-files/lib/ramips.sh 
b/target/linux/ramips/base-files/lib/ramips.sh
index cbe455d..76f0e43 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -316,6 +316,9 @@  ramips_board_detect() {
      *"NCS601W")
          name="ncs601w"
          ;;
+    *"NixcoreX1")
+        name="nixcore-x1"
+        ;;
      *"NW718")
          name="nw718"
          ;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh 
b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index 91c9997..0094568 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -94,6 +94,7 @@  platform_check_image() {
      mzk-w300nh2|\
      mzk-wdpr|\
      nbg-419n|\
+    nixcore|\
      nw718|\
      oy-0001|\
      pbr-m1|\
diff --git a/target/linux/ramips/dts/NIXCOREX1-16M.dts 
b/target/linux/ramips/dts/NIXCOREX1-16M.dts
new file mode 100644
index 0000000..1e1a205
--- /dev/null
+++ b/target/linux/ramips/dts/NIXCOREX1-16M.dts
@@ -0,0 +1,182 @@ 
+/dts-v1/;
+
+/include/ "rt5350.dtsi"
+
+/ {
+    compatible = "NixcoreX1", "ralink,rt5350-soc";
+    model = "NixcoreX1";
+
+    chosen{
+        bootargs = "console=ttyS1,57600";
+    };
+
+    gpio-export {
+        compatible = "gpio-export";
+        #size-cells = <0>;
+
+        gpio0 {
+            gpio-export,name = "gpio0";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio0 0 0>;
+        };
+        /* GPIOs 1-6 are I2C,SPI */
+
+        /* GPIO 7-14 are uart1 */
+
+        /* GPIOs 15 & 16 are uart2 */
+
+        /* JTAG */
+        gpio17 {
+            /* JTAG_TDO */
+            gpio-export,name = "gpio17";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio0 17 0>;
+        };
+        gpio18 {
+            /* JTAG_TDI */
+            gpio-export,name = "gpio18";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio0 18 0>;
+        };
+        gpio19 {
+            /* JTAG_TMS */
+            gpio-export,name = "gpio19";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio0 19 0>;
+        };
+        gpio20 {
+            /* JTAG_TCLK */
+            gpio-export,name = "gpio20";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio0 20 0>;
+        };
+        gpio21 {
+            /* JTAG_TRST_N */
+            gpio-export,name = "gpio21";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio0 21 0>;
+        };
+
+        /* ETH LEDs */
+        /*
+        gpio22 {
+            gpio-export,name = "gpio22";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio1 0 0>;
+        };
+        gpio23 {
+            gpio-export,name = "gpio23";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio1 1 0>;
+        };
+        gpio24 {
+            gpio-export,name = "gpio24";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio1 2 0>;
+        };
+        gpio25 {
+            gpio-export,name = "gpio25";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio1 3 0>;
+        };
+        */
+
+        gpio26 {
+            /* ETH4_LED */
+            gpio-export,name = "gpio26";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio1 4 0>;
+        };
+
+        gpio27 {
+            /* spi_cs1 */
+            gpio-export,name = "gpio27";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio1 5 0>;
+        };
+    };
+
+};
+
+&gpio0{
+    status = "okay";
+};
+
+&gpio1{
+    status = "okay";
+};
+
+&i2c{
+    status = "okay";
+};
+&uart{
+    status = "okay";
+    /* Mix of uart and gpio */
+    reset-names = "gpio uartf";
+};
+&spi0{
+    status = "okay";
+
+    m25p80@0 {
+        #address-cells = <1>;
+        #size-cells = <1>;
+        compatible = "s25fl064k";
+        reg = <0>;
+        linux,modalias = "m25p80", "s25fl064k";
+        spi-max-frequency = <10000000>;
+
+        partition@0 {
+            label = "uboot";
+            reg = <0x0 0x30000>;
+            read-only;
+        };
+
+        partition@30000 {
+            label = "uboot-env";
+            reg = <0x30000 0x10000>;
+            read-only;
+        };
+
+        factory: partition@40000 {
+            label = "factory";
+            reg = <0x40000 0x10000>;
+            read-only;
+        };
+
+        partition@50000 {
+            label = "firmware";
+            reg = <0x50000 0xfb0000>;
+        };
+    };
+};
+
+&pinctrl {
+    state_default: pinctrl0 {
+        gpio {
+            /* Associate the tjag, uartf and led groups with gpio */
+            ralink,group = "jtag", "led", "spi_cs1";
+            /* How do we set individual pins? */
+            ralink,function = "gpio";
+        };
+    };
+};
+
+&ethernet {
+    mtd-mac-address = <&factory 0x4>;
+};
+
+&esw {
+    ralink,portmap = <0x17>;
+};
+
+&wmac {
+    ralink,mtd-eeprom = <&factory 0>;
+};
+
+&ehci {
+    status = "okay";
+};
+
+&ohci {
+    status = "okay";
+};
diff --git a/target/linux/ramips/dts/NIXCOREX1-8M.dts 
b/target/linux/ramips/dts/NIXCOREX1-8M.dts
new file mode 100644
index 0000000..c514860
--- /dev/null
+++ b/target/linux/ramips/dts/NIXCOREX1-8M.dts
@@ -0,0 +1,183 @@ 
+/dts-v1/;
+
+/include/ "rt5350.dtsi"
+
+/ {
+    compatible = "NixcoreX1", "ralink,rt5350-soc";
+    model = "NixcoreX1";
+
+    chosen{
+        bootargs = "console=ttyS1,57600";
+    };
+
+    gpio-export {
+        compatible = "gpio-export";
+        #size-cells = <0>;
+
+        gpio0 {
+            gpio-export,name = "gpio0";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio0 0 0>;
+        };
+        /* GPIOs 1-6 are I2C,SPI */
+
+        /* GPIO 7-14 are uart1 */
+
+        /* GPIOs 15 & 16 are uart2 */
+
+        /* JTAG */
+        gpio17 {
+            /* JTAG_TDO */
+            gpio-export,name = "gpio17";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio0 17 0>;
+        };
+        gpio18 {
+            /* JTAG_TDI */
+            gpio-export,name = "gpio18";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio0 18 0>;
+        };
+        gpio19 {
+            /* JTAG_TMS */
+            gpio-export,name = "gpio19";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio0 19 0>;
+        };
+        gpio20 {
+            /* JTAG_TCLK */
+            gpio-export,name = "gpio20";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio0 20 0>;
+        };
+        gpio21 {
+            /* JTAG_TRST_N */
+            gpio-export,name = "gpio21";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio0 21 0>;
+        };
+
+        /* ETH LEDs */
+        /*
+        gpio22 {
+            gpio-export,name = "gpio22";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio1 0 0>;
+        };
+        gpio23 {
+            gpio-export,name = "gpio23";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio1 1 0>;
+        };
+        gpio24 {
+            gpio-export,name = "gpio24";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio1 2 0>;
+        };
+        gpio25 {
+            gpio-export,name = "gpio25";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio1 3 0>;
+        };
+        */
+
+        gpio26 {
+            /* ETH4_LED */
+            gpio-export,name = "gpio26";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio1 4 0>;
+        };
+
+        gpio27 {
+            /* spi_cs1 */
+            gpio-export,name = "gpio27";
+            gpio-export,direction_may_change = <1>;
+            gpios = <&gpio1 5 0>;
+        };
+    };
+
+};
+
+&gpio0{
+    status = "okay";
+};
+
+&gpio1{
+    status = "okay";
+};
+
+&i2c{
+    status = "okay";
+};
+&uart{
+    status = "okay";
+    /* Mix of uart and gpio */
+    reset-names = "gpio uartf";
+};
+&spi0{
+    status = "okay";
+
+    m25p80@0 {
+        #address-cells = <1>;
+        #size-cells = <1>;
+        compatible = "s25fl064k";
+        reg = <0>;
+        linux,modalias = "m25p80", "s25fl064k";
+        spi-max-frequency = <10000000>;
+
+        partition@0 {
+            label = "uboot";
+            reg = <0x0 0x30000>;
+            read-only;
+        };
+
+        partition@30000 {
+            label = "uboot-env";
+            reg = <0x30000 0x10000>;
+            read-only;
+        };
+
+        factory: partition@40000 {
+            label = "factory";
+            reg = <0x40000 0x10000>;
+            read-only;
+        };
+
+        partition@50000 {
+            label = "firmware";
+            reg = <0x50000 0x7b0000>;
+        };
+    };
+};
+
+&pinctrl {
+    state_default: pinctrl0 {
+        gpio {
+            /* Associate the tjag, uartf and led groups with gpio */
+            ralink,group = "jtag", "led", "spi_cs1";
+            /* How do we set individual pins? */
+            ralink,function = "gpio";
+        };
+    };
+};
+
+&ethernet {
+    mtd-mac-address = <&factory 0x4>;
+};
+
+&esw {
+    ralink,portmap = <0x17>;
+};
+
+&wmac {
+    ralink,mtd-eeprom = <&factory 0>;
+};
+
+&ehci {
+    status = "okay";
+};
+
+&ohci {
+    status = "okay";
+};
+
diff --git a/target/linux/ramips/image/rt305x.mk 
b/target/linux/ramips/image/rt305x.mk
index da7fc46..db12a8e 100644
--- a/target/linux/ramips/image/rt305x.mk
+++ b/target/linux/ramips/image/rt305x.mk
@@ -100,6 +100,21 @@  define BuildFirmware/HLKRM04/initramfs
      mkhilinkfw -e -i$(call imgname,$(1),$(2))-uImage.bin -o $(call 
imgname,$(1),$(2))-factory.bin;
  endef

+# This is called to build the nixcore image.  Build both 8MB and 16MB
+nixcore_8mb_mtd_size=8060928
+nixcore_16mb_mtd_size=16449536
+define BuildFirmware/NIXCOREX1/squashfs
+# Args are XXX, nixcore-mM and NIXCOREX1-xM
+    $(call 
BuildFirmware/CustomFlash/$(1),$(1),$(2)-8M,$(3)-8M,$(nixcore_8mb_mtd_size))
+    $(call 
BuildFirmware/CustomFlash/$(1),$(1),$(2)-16M,$(3)-16M,$(nixcore_16mb_mtd_size))
+    # Can do somethings here after the build?
+endef
+define BuildFirmware/NIXCOREX1/initramfs
+# Args are XXXX, nixcore-mM and NIXCOREX1-xM
+    $(call BuildFirmware/OF/initramfs,$(1),$(2)-8M,$(3)-8M)
+    $(call BuildFirmware/OF/initramfs,$(1),$(2)-16M,$(3)-16M)
+endef
+
  vocore_8mb_mtd_size=8060928
  vocore_16mb_mtd_size=16449536
  define BuildFirmware/VOCORE/squashfs
@@ -257,6 +272,7 @@  Image/Build/Profile/NBG-419N=$(call 
BuildFirmware/Default4M/$(1),$(1),nbg-419n,N
  Image/Build/Profile/MZKW300NH2=$(call 
BuildFirmware/Edimax/$(1),$(1),mzk-w300nh2,MZK-W300NH2,$(mzkw300nh2_mtd_size),CSYS,RN52,0x50000,0xc0000)
  Image/Build/Profile/MZKWDPR=$(call 
BuildFirmware/Default8M/$(1),$(1),mzk-wdpr,MZK-WDPR)
  Image/Build/Profile/NCS601W=$(call 
BuildFirmware/Default8M/$(1),$(1),ncs601W,NCS601W)
+Image/Build/Profile/NIXCOREX1=$(call 
BuildFirmware/NIXCOREX1/$(1),$(1),nixcorex1,NIXCOREX1)
  nw718_mtd_size=3801088
  Image/Build/Profile/NW718=$(call 
BuildFirmware/CustomFlashFactory/$(1),$(1),nw718m,NW718,$(nw718_mtd_size),ARA1B4NCRNW718;1,factory)
  Image/Build/Profile/M2M=$(call 
BuildFirmware/Default8M/$(1),$(1),m2m,M2M,Linux Kernel Image)
@@ -353,6 +369,7 @@  define Image/Build/Profile/Default
      $(call Image/Build/Profile/MZKWDPR,$(1))
      $(call Image/Build/Profile/NBG-419N,$(1))
      $(call Image/Build/Profile/NCS601W,$(1))
+    $(call Image/Build/Profile/NIXCOREX1,$(1))
      $(call Image/Build/Profile/NW718,$(1))
      $(call Image/Build/Profile/MINIEMBWIFI,$(1))
      $(call Image/Build/Profile/MINIEMBPLUG,$(1))
diff --git a/target/linux/ramips/rt305x/profiles/nixcore.mk 
b/target/linux/ramips/rt305x/profiles/nixcore.mk
new file mode 100644
index 0000000..22dee9b
--- /dev/null
+++ b/target/linux/ramips/rt305x/profiles/nixcore.mk
@@ -0,0 +1,20 @@ 
+#
+# Copyright (C) 2014 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/NIXCOREX1
+    NAME:=NixcoreX1
+    PACKAGES:=\
+        kmod-usb-core kmod-usb-ohci kmod-usb2 \
+        kmod-i2c-core kmod-i2c-ralink \
+        kmod-spi-dev
+endef
+
+define Profile/NIXCOREX1/Description
+    Package set for Nixcore X1 board
+endef
+
+$(eval $(call Profile,NIXCOREX1))