Message ID | 1450920774-22042-1-git-send-email-ldpinney@gmail.com |
---|---|
State | Accepted |
Headers | show |
Hi, On 24 December 2015 at 09:32, L. D. Pinney <ldpinney@gmail.com> wrote: > This patch adds support for the Bitmain Antrouter R1 > > http://wiki.openwrt.org/toh/bitmain/r1 > > Signed-off-by: L. D. Pinney <ldpinney@gmail.com> > --- > > V2 Corrects naming errors in Profile in V1 > > target/linux/ar71xx/base-files/etc/board.d/01_leds | 5 +++++ > target/linux/ar71xx/base-files/etc/board.d/02_network | 1 + > target/linux/ar71xx/base-files/etc/diag.sh | 3 +++ > target/linux/ar71xx/base-files/lib/ar71xx.sh | 3 +++ > target/linux/ar71xx/base-files/lib/upgrade/platform.sh | 1 + > target/linux/ar71xx/config-4.1 | 1 + > target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt | 10 ++++++++++ > target/linux/ar71xx/files/arch/mips/ath79/Makefile | 1 + > target/linux/ar71xx/files/arch/mips/ath79/mach-antrouter-r1.c | 8 +++++++- > target/linux/ar71xx/files/arch/mips/ath79/machtypes.h | 1 + > target/linux/ar71xx/generic/profiles/antminer.mk | 11 +++++++++++ > target/linux/ar71xx/image/Makefile | 10 +++++++++- > 12 files changed, 53 insertions(+), 2 deletions(-) > The patch may be fine but the diffstat apparently does not match the patch. > diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds > index 576d45b..cfb42a5 100755 > --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds > +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds > @@ -45,6 +45,11 @@ antminer-s3) > ucidef_set_led_default "lan" "LAN" "antminer-s3:yellow:lan" "0" > ;; > > +antrouter-r1) > + ucidef_set_led_wlan "wlan" "WLAN" "antrouter-r1:green:wlan" "phy0tpt" > + ucidef_set_led_default "btc" "BTC" "antrouter-r1:green:btc" "0" > + ;; > + > arduino-yun) > ucidef_set_led_wlan "wlan" "WLAN" "arduino:blue:wlan" "phy0tpt" > ucidef_set_led_usbdev "usb" "USB" "arduino:white:usb" "1-1.1" > diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network > index 8c57f2b..6b6c6a4 100755 > --- a/target/linux/ar71xx/base-files/etc/board.d/02_network > +++ b/target/linux/ar71xx/base-files/etc/board.d/02_network > @@ -317,6 +317,7 @@ dlan-pro-1200-ac) > all0305 |\ > antminer-s1 |\ > antminer-s3 |\ > +antrouter-r1 |\ > aw-nr580 |\ > bullet-m |\ > c-55 |\ > diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh > index 7e2dac8..13a0a98 100644 > --- a/target/linux/ar71xx/base-files/etc/diag.sh > +++ b/target/linux/ar71xx/base-files/etc/diag.sh > @@ -18,6 +18,9 @@ get_status_led() { > antminer-s3) > status_led="antminer-s3:green:system" > ;; > + antminer-r1) > + status_led="antminer-r1:green:system" > + ;; > ap132) > status_led="ap132:green:status" > ;; > diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh > index 46e6311..61dcbba 100755 > --- a/target/linux/ar71xx/base-files/lib/ar71xx.sh > +++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh > @@ -114,6 +114,9 @@ tplink_board_detect() { > "044403"*) > model="ANTMINER-S3" > ;; > + "44440101"*) > + model="ANTROUTER-R1" > + ;; Just out of curiosity, is it a design decision or just coincidence that these devices uses tplink style of firmware encapsulation? Regards, yousong > "120000"*) > model="MERCURY MAC1200R" > ;; > diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh > index e8998f4..cff7dfe 100755 > --- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh > +++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh > @@ -323,6 +323,7 @@ platform_check_image() { > > antminer-s1 | \ > antminer-s3 | \ > + antrouter-r1 | \ > archer-c5 | \ > archer-c7 | \ > el-m150 | \ > diff --git a/target/linux/ar71xx/config-4.1 b/target/linux/ar71xx/config-4.1 > index 7845aa2..fe1dd68 100644 > --- a/target/linux/ar71xx/config-4.1 > +++ b/target/linux/ar71xx/config-4.1 > @@ -35,6 +35,7 @@ CONFIG_ATH79_MACH_ALL0258N=y > CONFIG_ATH79_MACH_ALL0315N=y > CONFIG_ATH79_MACH_ANTMINER_S1=y > CONFIG_ATH79_MACH_ANTMINER_S3=y > +CONFIG_ATH79_MACH_ANTROUTER_R1=y > CONFIG_ATH79_MACH_AP113=y > CONFIG_ATH79_MACH_AP121=y > CONFIG_ATH79_MACH_AP132=y > diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt > index 84d22fe..cdd4fa2 100644 > --- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt > +++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt > @@ -72,6 +72,16 @@ config ATH79_MACH_ANTMINER_S3 > select ATH79_DEV_USB > select ATH79_DEV_WMAC > > +config ATH79_MACH_ANTROUTER_R1 > + bool "Bitmain Antrouter R1 support" > + select SOC_AR933X > + select ATH79_DEV_ETH > + select ATH79_DEV_GPIO_BUTTONS > + select ATH79_DEV_LEDS_GPIO > + select ATH79_DEV_M25P80 > + select ATH79_DEV_USB > + select ATH79_DEV_WMAC > + > config ATH79_MACH_ARDUINO_YUN > bool "Arduino Yun" > select SOC_AR933X > diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile > index 2d45225..991f6f2 100644 > --- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile > +++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile > @@ -44,6 +44,7 @@ obj-$(CONFIG_ATH79_MACH_ALL0258N) += mach-all0258n.o > obj-$(CONFIG_ATH79_MACH_ALL0315N) += mach-all0315n.o > obj-$(CONFIG_ATH79_MACH_ANTMINER_S1)+= mach-antminer-s1.o > obj-$(CONFIG_ATH79_MACH_ANTMINER_S3)+= mach-antminer-s3.o > +obj-$(CONFIG_ATH79_MACH_ANTROUTER_R1) += mach-antrouter-r1.o > obj-$(CONFIG_ATH79_MACH_ARDUINO_YUN) += mach-arduino-yun.o > obj-$(CONFIG_ATH79_MACH_AP113) += mach-ap113.o > obj-$(CONFIG_ATH79_MACH_AP121) += mach-ap121.o > diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-antrouter-r1.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-antrouter-r1.c > new file mode 100644 > index 0000000..a8f7b5d > --- /dev/null > +++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-antrouter-r1.c > @@ -0,0 +1,98 @@ > +/* > + * Bitmain Antrouter R1 board support > + * > + * Copyright (C) 2015 L. D. Pinney <ldpinney@gmail.com> > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms of the GNU General Public License version 2 as published > + * by the Free Software Foundation. > + */ > + > +#include <linux/gpio.h> > + > +#include <asm/mach-ath79/ath79.h> > +#include <asm/mach-ath79/ar71xx_regs.h> > + > +#include "common.h" > +#include "dev-eth.h" > +#include "dev-gpio-buttons.h" > +#include "dev-leds-gpio.h" > +#include "dev-m25p80.h" > +#include "dev-wmac.h" > +#include "machtypes.h" > +#include "dev-usb.h" > + > +#define ANTROUTER_R1_GPIO_BTN_RESET 11 > + > +#define ANTROUTER_R1_GPIO_LED_WLAN 0 > +#define ANTROUTER_R1_GPIO_LED_BTC 22 > +#define ANTROUTER_R1_GPIO_USB_POWER 18 > + > +#define ANTROUTER_R1_KEYSPOLL_INTERVAL 44 /* msecs */ > +#define ANTROUTER_R1_KEYSDEBOUNCE_INTERVAL (4 * ANTROUTER_R1_KEYSPOLL_INTERVAL) > + > +static const char *ANTROUTER_R1_part_probes[] = { > + "tp-link", > + NULL, > +}; > + > +static struct flash_platform_data ANTROUTER_R1_flash_data = { > + .part_probes = ANTROUTER_R1_part_probes, > +}; > + > +static struct gpio_led ANTROUTER_R1_leds_gpio[] __initdata = { > + { > + .name = "antrouter-r1:green:wlan", > + .gpio = ANTROUTER_R1_GPIO_LED_WLAN, > + .active_low = 0, > + },{ > + .name = "antrouter-r1:green:system", > + .gpio = ANTROUTER_R1_GPIO_LED_BTC, > + .active_low = 0, > + }, > +}; > + > +static struct gpio_keys_button ANTROUTER_R1_GPIO_keys[] __initdata = { > + { > + .desc = "reset", > + .type = EV_KEY, > + .code = KEY_RESTART, > + .debounce_interval = ANTROUTER_R1_KEYSDEBOUNCE_INTERVAL, > + .gpio = ANTROUTER_R1_GPIO_BTN_RESET, > + .active_low = 0, > + }, > +}; > + > +static void __init antrouter_r1_setup(void) > +{ > + u8 *mac = (u8 *) KSEG1ADDR(0x1f01fc00); > + u8 *ee = (u8 *) KSEG1ADDR(0x1fff1000); > + > + /* disable PHY_SWAP and PHY_ADDR_SWAP bits */ > + ath79_setup_ar933x_phy4_switch(false, false); > + > + ath79_register_leds_gpio(-1, ARRAY_SIZE(ANTROUTER_R1_leds_gpio), > + ANTROUTER_R1_leds_gpio); > + > + ath79_register_gpio_keys_polled(-1, ANTROUTER_R1_KEYSPOLL_INTERVAL, > + ARRAY_SIZE(ANTROUTER_R1_GPIO_keys), > + ANTROUTER_R1_GPIO_keys); > + > + gpio_request_one(ANTROUTER_R1_GPIO_USB_POWER, > + GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED, > + "USB power"); > + ath79_register_usb(); > + > + ath79_register_m25p80(&ANTROUTER_R1_flash_data); > + ath79_init_mac(ath79_eth0_data.mac_addr, mac, 1); > + ath79_init_mac(ath79_eth1_data.mac_addr, mac, -1); > + > + ath79_register_mdio(0, 0x0); > + ath79_register_eth(0); > + ath79_register_eth(1); > + > + ath79_register_wmac(ee, mac); > +} > + > +MIPS_MACHINE(ATH79_MACH_ANTROUTER_R1, "ANTROUTER-R1", > + "Antrouter-R1", antrouter_r1_setup); > diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h > index c32d44a..1b1c51a 100644 > --- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h > +++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h > @@ -23,6 +23,7 @@ enum ath79_mach_type { > ATH79_MACH_ALL0315N, /* Allnet ALL0315N */ > ATH79_MACH_ANTMINER_S1, /* Antminer S1 */ > ATH79_MACH_ANTMINER_S3, /* Antminer S3 */ > + ATH79_MACH_ANTROUTER_R1, /* Antrouter R1 */ > ATH79_MACH_ARDUINO_YUN, /* Yun */ > ATH79_MACH_AP113, /* Atheros AP113 reference board */ > ATH79_MACH_AP121, /* Atheros AP121 reference board */ > diff --git a/target/linux/ar71xx/generic/profiles/antminer.mk b/target/linux/ar71xx/generic/profiles/antminer.mk > index d59a089..72019e3 100644 > --- a/target/linux/ar71xx/generic/profiles/antminer.mk > +++ b/target/linux/ar71xx/generic/profiles/antminer.mk > @@ -26,3 +26,14 @@ define Profile/ANTMINERS3/Description > Package set optimized for the Bitmain Antminer S3. > endef > $(eval $(call Profile,ANTMINERS3)) > + > +define Profile/ANTROUTERR1 > + NAME:=Antrouter-R1 > + PACKAGES:=kmod-usb-core kmod-usb2 > +endef > + > + > +define Profile/ANTROUTERR1/Description > + Package set optimized for the Bitmain Antrouter R1. > +endef > +$(eval $(call Profile,ANTROUTERR1)) > diff --git a/target/linux/ar71xx/image/Makefile b/target/linux/ar71xx/image/Makefile > index d214eae..182fb4d 100644 > --- a/target/linux/ar71xx/image/Makefile > +++ b/target/linux/ar71xx/image/Makefile > @@ -461,6 +461,14 @@ define Device/antminer-s3 > CONSOLE := ttyATH0,115200 > endef > > +define Device/antrouter-r1 > + $(Device/tplink-8mlzma) > + BOARDNAME := ANTROUTER-R1 > + DEVICE_PROFILE := ANTROUTERR1 > + TPLINK_HWID := 0x44440101 > + CONSOLE := ttyATH0,115200 > +endef > + > define Device/el-m150 > $(Device/tplink-8mlzma) > BOARDNAME := EL-M150 > @@ -476,7 +484,7 @@ define Device/el-mini > TPLINK_HWID := 0x01530001 > CONSOLE := ttyATH0,115200 > endef > -TARGET_DEVICES += antminer-s1 antminer-s3 el-m150 el-mini > +TARGET_DEVICES += antminer-s1 antminer-s3 antrouter-r1 el-m150 el-mini > > define Device/gl-inet-6408A-v1 > $(Device/tplink-8mlzma) > _______________________________________________ > openwrt-devel mailing list > openwrt-devel@lists.openwrt.org > https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
Sorry the diff stat doesn't seem to match maybe I used 'diff --stat' rather than 'diff origin/master --stat' target/linux/ar71xx/base-files/etc/board.d/01_leds | 5 ++++ target/linux/ar71xx/base-files/etc/board.d/02_network | 1 + target/linux/ar71xx/base-files/etc/diag.sh | 3 ++ target/linux/ar71xx/base-files/lib/ar71xx.sh | 3 ++ target/linux/ar71xx/base-files/lib/upgrade/platform.sh | 1 + target/linux/ar71xx/config-4.1 | 1 + target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt | 10 +++++++ target/linux/ar71xx/files/arch/mips/ath79/Makefile | 1 + target/linux/ar71xx/files/arch/mips/ath79/mach-antrouter-r1.c | 98 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ target/linux/ar71xx/files/arch/mips/ath79/machtypes.h | 1 + target/linux/ar71xx/generic/profiles/antminer.mk | 11 +++++++ target/linux/ar71xx/image/Makefile | 10 ++++++- 12 files changed, 144 insertions(+), 1 deletion(-) Bitmain or their firmware 'team' used AA same as the antminer s1/s3 and reused the 'tplink profile' for a tplink router....basically a hack job. I have no Idea why they can't do things more properly. On Thu, Dec 24, 2015 at 7:41 AM, Yousong Zhou <yszhou4tech@gmail.com> wrote: > Hi, > > On 24 December 2015 at 09:32, L. D. Pinney <ldpinney@gmail.com> wrote: > > This patch adds support for the Bitmain Antrouter R1 > > > > http://wiki.openwrt.org/toh/bitmain/r1 > > > > Signed-off-by: L. D. Pinney <ldpinney@gmail.com> > > --- > > > > V2 Corrects naming errors in Profile in V1 > > > > target/linux/ar71xx/base-files/etc/board.d/01_leds | 5 +++++ > > target/linux/ar71xx/base-files/etc/board.d/02_network | 1 + > > target/linux/ar71xx/base-files/etc/diag.sh | 3 +++ > > target/linux/ar71xx/base-files/lib/ar71xx.sh | 3 +++ > > target/linux/ar71xx/base-files/lib/upgrade/platform.sh | 1 + > > target/linux/ar71xx/config-4.1 | 1 + > > target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt | 10 > ++++++++++ > > target/linux/ar71xx/files/arch/mips/ath79/Makefile | 1 + > > target/linux/ar71xx/files/arch/mips/ath79/mach-antrouter-r1.c | 8 > +++++++- > > target/linux/ar71xx/files/arch/mips/ath79/machtypes.h | 1 + > > target/linux/ar71xx/generic/profiles/antminer.mk | 11 > +++++++++++ > > target/linux/ar71xx/image/Makefile | 10 > +++++++++- > > 12 files changed, 53 insertions(+), 2 deletions(-) > > > > The patch may be fine but the diffstat apparently does not match the patch. > > > diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds > b/target/linux/ar71xx/base-files/etc/board.d/01_leds > > index 576d45b..cfb42a5 100755 > > --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds > > +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds > > @@ -45,6 +45,11 @@ antminer-s3) > > ucidef_set_led_default "lan" "LAN" "antminer-s3:yellow:lan" "0" > > ;; > > > > +antrouter-r1) > > + ucidef_set_led_wlan "wlan" "WLAN" "antrouter-r1:green:wlan" > "phy0tpt" > > + ucidef_set_led_default "btc" "BTC" "antrouter-r1:green:btc" "0" > > + ;; > > + > > arduino-yun) > > ucidef_set_led_wlan "wlan" "WLAN" "arduino:blue:wlan" "phy0tpt" > > ucidef_set_led_usbdev "usb" "USB" "arduino:white:usb" "1-1.1" > > diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network > b/target/linux/ar71xx/base-files/etc/board.d/02_network > > index 8c57f2b..6b6c6a4 100755 > > --- a/target/linux/ar71xx/base-files/etc/board.d/02_network > > +++ b/target/linux/ar71xx/base-files/etc/board.d/02_network > > @@ -317,6 +317,7 @@ dlan-pro-1200-ac) > > all0305 |\ > > antminer-s1 |\ > > antminer-s3 |\ > > +antrouter-r1 |\ > > aw-nr580 |\ > > bullet-m |\ > > c-55 |\ > > diff --git a/target/linux/ar71xx/base-files/etc/diag.sh > b/target/linux/ar71xx/base-files/etc/diag.sh > > index 7e2dac8..13a0a98 100644 > > --- a/target/linux/ar71xx/base-files/etc/diag.sh > > +++ b/target/linux/ar71xx/base-files/etc/diag.sh > > @@ -18,6 +18,9 @@ get_status_led() { > > antminer-s3) > > status_led="antminer-s3:green:system" > > ;; > > + antminer-r1) > > + status_led="antminer-r1:green:system" > > + ;; > > ap132) > > status_led="ap132:green:status" > > ;; > > diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh > b/target/linux/ar71xx/base-files/lib/ar71xx.sh > > index 46e6311..61dcbba 100755 > > --- a/target/linux/ar71xx/base-files/lib/ar71xx.sh > > +++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh > > @@ -114,6 +114,9 @@ tplink_board_detect() { > > "044403"*) > > model="ANTMINER-S3" > > ;; > > + "44440101"*) > > + model="ANTROUTER-R1" > > + ;; > > Just out of curiosity, is it a design decision or just coincidence > that these devices uses tplink style of firmware encapsulation? > > Regards, > yousong > > > "120000"*) > > model="MERCURY MAC1200R" > > ;; > > diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh > b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh > > index e8998f4..cff7dfe 100755 > > --- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh > > +++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh > > @@ -323,6 +323,7 @@ platform_check_image() { > > > > antminer-s1 | \ > > antminer-s3 | \ > > + antrouter-r1 | \ > > archer-c5 | \ > > archer-c7 | \ > > el-m150 | \ > > diff --git a/target/linux/ar71xx/config-4.1 > b/target/linux/ar71xx/config-4.1 > > index 7845aa2..fe1dd68 100644 > > --- a/target/linux/ar71xx/config-4.1 > > +++ b/target/linux/ar71xx/config-4.1 > > @@ -35,6 +35,7 @@ CONFIG_ATH79_MACH_ALL0258N=y > > CONFIG_ATH79_MACH_ALL0315N=y > > CONFIG_ATH79_MACH_ANTMINER_S1=y > > CONFIG_ATH79_MACH_ANTMINER_S3=y > > +CONFIG_ATH79_MACH_ANTROUTER_R1=y > > CONFIG_ATH79_MACH_AP113=y > > CONFIG_ATH79_MACH_AP121=y > > CONFIG_ATH79_MACH_AP132=y > > diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt > b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt > > index 84d22fe..cdd4fa2 100644 > > --- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt > > +++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt > > @@ -72,6 +72,16 @@ config ATH79_MACH_ANTMINER_S3 > > select ATH79_DEV_USB > > select ATH79_DEV_WMAC > > > > +config ATH79_MACH_ANTROUTER_R1 > > + bool "Bitmain Antrouter R1 support" > > + select SOC_AR933X > > + select ATH79_DEV_ETH > > + select ATH79_DEV_GPIO_BUTTONS > > + select ATH79_DEV_LEDS_GPIO > > + select ATH79_DEV_M25P80 > > + select ATH79_DEV_USB > > + select ATH79_DEV_WMAC > > + > > config ATH79_MACH_ARDUINO_YUN > > bool "Arduino Yun" > > select SOC_AR933X > > diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile > b/target/linux/ar71xx/files/arch/mips/ath79/Makefile > > index 2d45225..991f6f2 100644 > > --- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile > > +++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile > > @@ -44,6 +44,7 @@ obj-$(CONFIG_ATH79_MACH_ALL0258N) += > mach-all0258n.o > > obj-$(CONFIG_ATH79_MACH_ALL0315N) += mach-all0315n.o > > obj-$(CONFIG_ATH79_MACH_ANTMINER_S1)+= mach-antminer-s1.o > > obj-$(CONFIG_ATH79_MACH_ANTMINER_S3)+= mach-antminer-s3.o > > +obj-$(CONFIG_ATH79_MACH_ANTROUTER_R1) += mach-antrouter-r1.o > > obj-$(CONFIG_ATH79_MACH_ARDUINO_YUN) += mach-arduino-yun.o > > obj-$(CONFIG_ATH79_MACH_AP113) += mach-ap113.o > > obj-$(CONFIG_ATH79_MACH_AP121) += mach-ap121.o > > diff --git > a/target/linux/ar71xx/files/arch/mips/ath79/mach-antrouter-r1.c > b/target/linux/ar71xx/files/arch/mips/ath79/mach-antrouter-r1.c > > new file mode 100644 > > index 0000000..a8f7b5d > > --- /dev/null > > +++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-antrouter-r1.c > > @@ -0,0 +1,98 @@ > > +/* > > + * Bitmain Antrouter R1 board support > > + * > > + * Copyright (C) 2015 L. D. Pinney <ldpinney@gmail.com> > > + * > > + * This program is free software; you can redistribute it and/or > modify it > > + * under the terms of the GNU General Public License version 2 as > published > > + * by the Free Software Foundation. > > + */ > > + > > +#include <linux/gpio.h> > > + > > +#include <asm/mach-ath79/ath79.h> > > +#include <asm/mach-ath79/ar71xx_regs.h> > > + > > +#include "common.h" > > +#include "dev-eth.h" > > +#include "dev-gpio-buttons.h" > > +#include "dev-leds-gpio.h" > > +#include "dev-m25p80.h" > > +#include "dev-wmac.h" > > +#include "machtypes.h" > > +#include "dev-usb.h" > > + > > +#define ANTROUTER_R1_GPIO_BTN_RESET 11 > > + > > +#define ANTROUTER_R1_GPIO_LED_WLAN 0 > > +#define ANTROUTER_R1_GPIO_LED_BTC 22 > > +#define ANTROUTER_R1_GPIO_USB_POWER 18 > > + > > +#define ANTROUTER_R1_KEYSPOLL_INTERVAL 44 /* msecs */ > > +#define ANTROUTER_R1_KEYSDEBOUNCE_INTERVAL (4 * > ANTROUTER_R1_KEYSPOLL_INTERVAL) > > + > > +static const char *ANTROUTER_R1_part_probes[] = { > > + "tp-link", > > + NULL, > > +}; > > + > > +static struct flash_platform_data ANTROUTER_R1_flash_data = { > > + .part_probes = ANTROUTER_R1_part_probes, > > +}; > > + > > +static struct gpio_led ANTROUTER_R1_leds_gpio[] __initdata = { > > + { > > + .name = "antrouter-r1:green:wlan", > > + .gpio = ANTROUTER_R1_GPIO_LED_WLAN, > > + .active_low = 0, > > + },{ > > + .name = "antrouter-r1:green:system", > > + .gpio = ANTROUTER_R1_GPIO_LED_BTC, > > + .active_low = 0, > > + }, > > +}; > > + > > +static struct gpio_keys_button ANTROUTER_R1_GPIO_keys[] __initdata = { > > + { > > + .desc = "reset", > > + .type = EV_KEY, > > + .code = KEY_RESTART, > > + .debounce_interval = ANTROUTER_R1_KEYSDEBOUNCE_INTERVAL, > > + .gpio = ANTROUTER_R1_GPIO_BTN_RESET, > > + .active_low = 0, > > + }, > > +}; > > + > > +static void __init antrouter_r1_setup(void) > > +{ > > + u8 *mac = (u8 *) KSEG1ADDR(0x1f01fc00); > > + u8 *ee = (u8 *) KSEG1ADDR(0x1fff1000); > > + > > + /* disable PHY_SWAP and PHY_ADDR_SWAP bits */ > > + ath79_setup_ar933x_phy4_switch(false, false); > > + > > + ath79_register_leds_gpio(-1, ARRAY_SIZE(ANTROUTER_R1_leds_gpio), > > + ANTROUTER_R1_leds_gpio); > > + > > + ath79_register_gpio_keys_polled(-1, > ANTROUTER_R1_KEYSPOLL_INTERVAL, > > + > ARRAY_SIZE(ANTROUTER_R1_GPIO_keys), > > + ANTROUTER_R1_GPIO_keys); > > + > > + gpio_request_one(ANTROUTER_R1_GPIO_USB_POWER, > > + GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED, > > + "USB power"); > > + ath79_register_usb(); > > + > > + ath79_register_m25p80(&ANTROUTER_R1_flash_data); > > + ath79_init_mac(ath79_eth0_data.mac_addr, mac, 1); > > + ath79_init_mac(ath79_eth1_data.mac_addr, mac, -1); > > + > > + ath79_register_mdio(0, 0x0); > > + ath79_register_eth(0); > > + ath79_register_eth(1); > > + > > + ath79_register_wmac(ee, mac); > > +} > > + > > +MIPS_MACHINE(ATH79_MACH_ANTROUTER_R1, "ANTROUTER-R1", > > + "Antrouter-R1", antrouter_r1_setup); > > diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h > b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h > > index c32d44a..1b1c51a 100644 > > --- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h > > +++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h > > @@ -23,6 +23,7 @@ enum ath79_mach_type { > > ATH79_MACH_ALL0315N, /* Allnet ALL0315N */ > > ATH79_MACH_ANTMINER_S1, /* Antminer S1 */ > > ATH79_MACH_ANTMINER_S3, /* Antminer S3 */ > > + ATH79_MACH_ANTROUTER_R1, /* Antrouter R1 */ > > ATH79_MACH_ARDUINO_YUN, /* Yun */ > > ATH79_MACH_AP113, /* Atheros AP113 reference board > */ > > ATH79_MACH_AP121, /* Atheros AP121 reference board > */ > > diff --git a/target/linux/ar71xx/generic/profiles/antminer.mk > b/target/linux/ar71xx/generic/profiles/antminer.mk > > index d59a089..72019e3 100644 > > --- a/target/linux/ar71xx/generic/profiles/antminer.mk > > +++ b/target/linux/ar71xx/generic/profiles/antminer.mk > > @@ -26,3 +26,14 @@ define Profile/ANTMINERS3/Description > > Package set optimized for the Bitmain Antminer S3. > > endef > > $(eval $(call Profile,ANTMINERS3)) > > + > > +define Profile/ANTROUTERR1 > > + NAME:=Antrouter-R1 > > + PACKAGES:=kmod-usb-core kmod-usb2 > > +endef > > + > > + > > +define Profile/ANTROUTERR1/Description > > + Package set optimized for the Bitmain Antrouter R1. > > +endef > > +$(eval $(call Profile,ANTROUTERR1)) > > diff --git a/target/linux/ar71xx/image/Makefile > b/target/linux/ar71xx/image/Makefile > > index d214eae..182fb4d 100644 > > --- a/target/linux/ar71xx/image/Makefile > > +++ b/target/linux/ar71xx/image/Makefile > > @@ -461,6 +461,14 @@ define Device/antminer-s3 > > CONSOLE := ttyATH0,115200 > > endef > > > > +define Device/antrouter-r1 > > + $(Device/tplink-8mlzma) > > + BOARDNAME := ANTROUTER-R1 > > + DEVICE_PROFILE := ANTROUTERR1 > > + TPLINK_HWID := 0x44440101 > > + CONSOLE := ttyATH0,115200 > > +endef > > + > > define Device/el-m150 > > $(Device/tplink-8mlzma) > > BOARDNAME := EL-M150 > > @@ -476,7 +484,7 @@ define Device/el-mini > > TPLINK_HWID := 0x01530001 > > CONSOLE := ttyATH0,115200 > > endef > > -TARGET_DEVICES += antminer-s1 antminer-s3 el-m150 el-mini > > +TARGET_DEVICES += antminer-s1 antminer-s3 antrouter-r1 el-m150 el-mini > > > > define Device/gl-inet-6408A-v1 > > $(Device/tplink-8mlzma) > > _______________________________________________ > > openwrt-devel mailing list > > openwrt-devel@lists.openwrt.org > > https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel >
diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds index 576d45b..cfb42a5 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds @@ -45,6 +45,11 @@ antminer-s3) ucidef_set_led_default "lan" "LAN" "antminer-s3:yellow:lan" "0" ;; +antrouter-r1) + ucidef_set_led_wlan "wlan" "WLAN" "antrouter-r1:green:wlan" "phy0tpt" + ucidef_set_led_default "btc" "BTC" "antrouter-r1:green:btc" "0" + ;; + arduino-yun) ucidef_set_led_wlan "wlan" "WLAN" "arduino:blue:wlan" "phy0tpt" ucidef_set_led_usbdev "usb" "USB" "arduino:white:usb" "1-1.1" diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network index 8c57f2b..6b6c6a4 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/02_network +++ b/target/linux/ar71xx/base-files/etc/board.d/02_network @@ -317,6 +317,7 @@ dlan-pro-1200-ac) all0305 |\ antminer-s1 |\ antminer-s3 |\ +antrouter-r1 |\ aw-nr580 |\ bullet-m |\ c-55 |\ diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh index 7e2dac8..13a0a98 100644 --- a/target/linux/ar71xx/base-files/etc/diag.sh +++ b/target/linux/ar71xx/base-files/etc/diag.sh @@ -18,6 +18,9 @@ get_status_led() { antminer-s3) status_led="antminer-s3:green:system" ;; + antminer-r1) + status_led="antminer-r1:green:system" + ;; ap132) status_led="ap132:green:status" ;; diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh index 46e6311..61dcbba 100755 --- a/target/linux/ar71xx/base-files/lib/ar71xx.sh +++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh @@ -114,6 +114,9 @@ tplink_board_detect() { "044403"*) model="ANTMINER-S3" ;; + "44440101"*) + model="ANTROUTER-R1" + ;; "120000"*) model="MERCURY MAC1200R" ;; diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh index e8998f4..cff7dfe 100755 --- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh @@ -323,6 +323,7 @@ platform_check_image() { antminer-s1 | \ antminer-s3 | \ + antrouter-r1 | \ archer-c5 | \ archer-c7 | \ el-m150 | \ diff --git a/target/linux/ar71xx/config-4.1 b/target/linux/ar71xx/config-4.1 index 7845aa2..fe1dd68 100644 --- a/target/linux/ar71xx/config-4.1 +++ b/target/linux/ar71xx/config-4.1 @@ -35,6 +35,7 @@ CONFIG_ATH79_MACH_ALL0258N=y CONFIG_ATH79_MACH_ALL0315N=y CONFIG_ATH79_MACH_ANTMINER_S1=y CONFIG_ATH79_MACH_ANTMINER_S3=y +CONFIG_ATH79_MACH_ANTROUTER_R1=y CONFIG_ATH79_MACH_AP113=y CONFIG_ATH79_MACH_AP121=y CONFIG_ATH79_MACH_AP132=y diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt index 84d22fe..cdd4fa2 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt +++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt @@ -72,6 +72,16 @@ config ATH79_MACH_ANTMINER_S3 select ATH79_DEV_USB select ATH79_DEV_WMAC +config ATH79_MACH_ANTROUTER_R1 + bool "Bitmain Antrouter R1 support" + select SOC_AR933X + select ATH79_DEV_ETH + select ATH79_DEV_GPIO_BUTTONS + select ATH79_DEV_LEDS_GPIO + select ATH79_DEV_M25P80 + select ATH79_DEV_USB + select ATH79_DEV_WMAC + config ATH79_MACH_ARDUINO_YUN bool "Arduino Yun" select SOC_AR933X diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile index 2d45225..991f6f2 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile +++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile @@ -44,6 +44,7 @@ obj-$(CONFIG_ATH79_MACH_ALL0258N) += mach-all0258n.o obj-$(CONFIG_ATH79_MACH_ALL0315N) += mach-all0315n.o obj-$(CONFIG_ATH79_MACH_ANTMINER_S1)+= mach-antminer-s1.o obj-$(CONFIG_ATH79_MACH_ANTMINER_S3)+= mach-antminer-s3.o +obj-$(CONFIG_ATH79_MACH_ANTROUTER_R1) += mach-antrouter-r1.o obj-$(CONFIG_ATH79_MACH_ARDUINO_YUN) += mach-arduino-yun.o obj-$(CONFIG_ATH79_MACH_AP113) += mach-ap113.o obj-$(CONFIG_ATH79_MACH_AP121) += mach-ap121.o diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-antrouter-r1.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-antrouter-r1.c new file mode 100644 index 0000000..a8f7b5d --- /dev/null +++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-antrouter-r1.c @@ -0,0 +1,98 @@ +/* + * Bitmain Antrouter R1 board support + * + * Copyright (C) 2015 L. D. Pinney <ldpinney@gmail.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published + * by the Free Software Foundation. + */ + +#include <linux/gpio.h> + +#include <asm/mach-ath79/ath79.h> +#include <asm/mach-ath79/ar71xx_regs.h> + +#include "common.h" +#include "dev-eth.h" +#include "dev-gpio-buttons.h" +#include "dev-leds-gpio.h" +#include "dev-m25p80.h" +#include "dev-wmac.h" +#include "machtypes.h" +#include "dev-usb.h" + +#define ANTROUTER_R1_GPIO_BTN_RESET 11 + +#define ANTROUTER_R1_GPIO_LED_WLAN 0 +#define ANTROUTER_R1_GPIO_LED_BTC 22 +#define ANTROUTER_R1_GPIO_USB_POWER 18 + +#define ANTROUTER_R1_KEYSPOLL_INTERVAL 44 /* msecs */ +#define ANTROUTER_R1_KEYSDEBOUNCE_INTERVAL (4 * ANTROUTER_R1_KEYSPOLL_INTERVAL) + +static const char *ANTROUTER_R1_part_probes[] = { + "tp-link", + NULL, +}; + +static struct flash_platform_data ANTROUTER_R1_flash_data = { + .part_probes = ANTROUTER_R1_part_probes, +}; + +static struct gpio_led ANTROUTER_R1_leds_gpio[] __initdata = { + { + .name = "antrouter-r1:green:wlan", + .gpio = ANTROUTER_R1_GPIO_LED_WLAN, + .active_low = 0, + },{ + .name = "antrouter-r1:green:system", + .gpio = ANTROUTER_R1_GPIO_LED_BTC, + .active_low = 0, + }, +}; + +static struct gpio_keys_button ANTROUTER_R1_GPIO_keys[] __initdata = { + { + .desc = "reset", + .type = EV_KEY, + .code = KEY_RESTART, + .debounce_interval = ANTROUTER_R1_KEYSDEBOUNCE_INTERVAL, + .gpio = ANTROUTER_R1_GPIO_BTN_RESET, + .active_low = 0, + }, +}; + +static void __init antrouter_r1_setup(void) +{ + u8 *mac = (u8 *) KSEG1ADDR(0x1f01fc00); + u8 *ee = (u8 *) KSEG1ADDR(0x1fff1000); + + /* disable PHY_SWAP and PHY_ADDR_SWAP bits */ + ath79_setup_ar933x_phy4_switch(false, false); + + ath79_register_leds_gpio(-1, ARRAY_SIZE(ANTROUTER_R1_leds_gpio), + ANTROUTER_R1_leds_gpio); + + ath79_register_gpio_keys_polled(-1, ANTROUTER_R1_KEYSPOLL_INTERVAL, + ARRAY_SIZE(ANTROUTER_R1_GPIO_keys), + ANTROUTER_R1_GPIO_keys); + + gpio_request_one(ANTROUTER_R1_GPIO_USB_POWER, + GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED, + "USB power"); + ath79_register_usb(); + + ath79_register_m25p80(&ANTROUTER_R1_flash_data); + ath79_init_mac(ath79_eth0_data.mac_addr, mac, 1); + ath79_init_mac(ath79_eth1_data.mac_addr, mac, -1); + + ath79_register_mdio(0, 0x0); + ath79_register_eth(0); + ath79_register_eth(1); + + ath79_register_wmac(ee, mac); +} + +MIPS_MACHINE(ATH79_MACH_ANTROUTER_R1, "ANTROUTER-R1", + "Antrouter-R1", antrouter_r1_setup); diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h index c32d44a..1b1c51a 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h +++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h @@ -23,6 +23,7 @@ enum ath79_mach_type { ATH79_MACH_ALL0315N, /* Allnet ALL0315N */ ATH79_MACH_ANTMINER_S1, /* Antminer S1 */ ATH79_MACH_ANTMINER_S3, /* Antminer S3 */ + ATH79_MACH_ANTROUTER_R1, /* Antrouter R1 */ ATH79_MACH_ARDUINO_YUN, /* Yun */ ATH79_MACH_AP113, /* Atheros AP113 reference board */ ATH79_MACH_AP121, /* Atheros AP121 reference board */ diff --git a/target/linux/ar71xx/generic/profiles/antminer.mk b/target/linux/ar71xx/generic/profiles/antminer.mk index d59a089..72019e3 100644 --- a/target/linux/ar71xx/generic/profiles/antminer.mk +++ b/target/linux/ar71xx/generic/profiles/antminer.mk @@ -26,3 +26,14 @@ define Profile/ANTMINERS3/Description Package set optimized for the Bitmain Antminer S3. endef $(eval $(call Profile,ANTMINERS3)) + +define Profile/ANTROUTERR1 + NAME:=Antrouter-R1 + PACKAGES:=kmod-usb-core kmod-usb2 +endef + + +define Profile/ANTROUTERR1/Description + Package set optimized for the Bitmain Antrouter R1. +endef +$(eval $(call Profile,ANTROUTERR1)) diff --git a/target/linux/ar71xx/image/Makefile b/target/linux/ar71xx/image/Makefile index d214eae..182fb4d 100644 --- a/target/linux/ar71xx/image/Makefile +++ b/target/linux/ar71xx/image/Makefile @@ -461,6 +461,14 @@ define Device/antminer-s3 CONSOLE := ttyATH0,115200 endef +define Device/antrouter-r1 + $(Device/tplink-8mlzma) + BOARDNAME := ANTROUTER-R1 + DEVICE_PROFILE := ANTROUTERR1 + TPLINK_HWID := 0x44440101 + CONSOLE := ttyATH0,115200 +endef + define Device/el-m150 $(Device/tplink-8mlzma) BOARDNAME := EL-M150 @@ -476,7 +484,7 @@ define Device/el-mini TPLINK_HWID := 0x01530001 CONSOLE := ttyATH0,115200 endef -TARGET_DEVICES += antminer-s1 antminer-s3 el-m150 el-mini +TARGET_DEVICES += antminer-s1 antminer-s3 antrouter-r1 el-m150 el-mini define Device/gl-inet-6408A-v1 $(Device/tplink-8mlzma)
This patch adds support for the Bitmain Antrouter R1 http://wiki.openwrt.org/toh/bitmain/r1 Signed-off-by: L. D. Pinney <ldpinney@gmail.com> --- V2 Corrects naming errors in Profile in V1 target/linux/ar71xx/base-files/etc/board.d/01_leds | 5 +++++ target/linux/ar71xx/base-files/etc/board.d/02_network | 1 + target/linux/ar71xx/base-files/etc/diag.sh | 3 +++ target/linux/ar71xx/base-files/lib/ar71xx.sh | 3 +++ target/linux/ar71xx/base-files/lib/upgrade/platform.sh | 1 + target/linux/ar71xx/config-4.1 | 1 + target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt | 10 ++++++++++ target/linux/ar71xx/files/arch/mips/ath79/Makefile | 1 + target/linux/ar71xx/files/arch/mips/ath79/mach-antrouter-r1.c | 8 +++++++- target/linux/ar71xx/files/arch/mips/ath79/machtypes.h | 1 + target/linux/ar71xx/generic/profiles/antminer.mk | 11 +++++++++++ target/linux/ar71xx/image/Makefile | 10 +++++++++- 12 files changed, 53 insertions(+), 2 deletions(-)