Message ID | 1448883168-30742-3-git-send-email-LW@KARO-electronics.de |
---|---|
State | Changes Requested, archived |
Delegated to: | David Miller |
Headers | show |
On Mon, Nov 30, 2015 at 9:32 AM, Lothar Waßmann <LW@karo-electronics.de> wrote: > - gpio_set_value_cansleep(phy_reset, 1); > + gpiod_set_value_cansleep(phy_reset, 1); This will break some existing DTBs. Currently the fec driver does not care whether 'phy-reset-gpios' is active low or active high. (Yes, it was a mistake to assume in the driver that it is always active low.) After this change the polarity will be taken into account and may break some dtb's. I suggest you to send a single patch with the minimum changes to fix the regression caused by 8fff755e9f8d ("net: fec: Ensure clocks are enabled while using mdio bus"). -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
From: Lothar Waßmann <LW@KARO-electronics.de> Sent: Monday, November 30, 2015 7:33 PM > To: Andrew Lunn; David S. Miller; Estevam Fabio-R49496; Greg Ungerer; > Kevin Hao; Lothar Waßmann; Lucas Stach; Duan Fugang-B38611; Philippe > Reynes; Richard Cochran; Russell King; Sascha Hauer; Stefan Agner; linux- > kernel@vger.kernel.org; netdev@vger.kernel.org; Jeff Kirsher; Uwe Kleine- > König > Subject: [PATCH 2/3] net: fec: convert to using gpiod framework > > Use gpiod_get_optional() instead of checking for a valid GPIO number and > calling devm_gpio_request_one() conditionally. > > Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> > --- > drivers/net/ethernet/freescale/fec_main.c | 17 +++++++---------- > 1 file changed, 7 insertions(+), 10 deletions(-) > > diff --git a/drivers/net/ethernet/freescale/fec_main.c > b/drivers/net/ethernet/freescale/fec_main.c > index e17d74f..1a983fc 100644 > --- a/drivers/net/ethernet/freescale/fec_main.c > +++ b/drivers/net/ethernet/freescale/fec_main.c > @@ -3233,7 +3233,7 @@ static int fec_enet_init(struct net_device *ndev) > #ifdef CONFIG_OF static void fec_reset_phy(struct platform_device *pdev) > { > - int err, phy_reset; > + struct gpio_desc *phy_reset; > int msec = 1; > struct device_node *np = pdev->dev.of_node; > > @@ -3245,18 +3245,15 @@ static void fec_reset_phy(struct platform_device > *pdev) > if (msec > 1000) > msec = 1; > > - phy_reset = of_get_named_gpio(np, "phy-reset-gpios", 0); > - if (!gpio_is_valid(phy_reset)) > - return; > - > - err = devm_gpio_request_one(&pdev->dev, phy_reset, > - GPIOF_OUT_INIT_LOW, "phy-reset"); > - if (err) { > - dev_err(&pdev->dev, "failed to get phy-reset-gpios: %d\n", > err); > + phy_reset = devm_gpiod_get_optional(&pdev->dev, "phy-reset", > + GPIOD_OUT_LOW); > + if (IS_ERR(phy_reset)) { > + dev_err(&pdev->dev, "failed to get phy-reset-gpios: %ld\n", > + PTR_ERR(phy_reset)); > return; > } > msleep(msec); > - gpio_set_value_cansleep(phy_reset, 1); > + gpiod_set_value_cansleep(phy_reset, 1); This API will judge the GPIO active polarity, there many imx boards in dts files don't care the polarity. So pls drop the patch. Or use gpiod_set_raw_value_cansleep() instead of gpiod_set_value_cansleep(). > } > #else /* CONFIG_OF */ > static void fec_reset_phy(struct platform_device *pdev) > -- > 2.1.4
Hi, > From: Lothar Waßmann <LW@KARO-electronics.de> Sent: Monday, November 30, 2015 7:33 PM > > To: Andrew Lunn; David S. Miller; Estevam Fabio-R49496; Greg Ungerer; > > Kevin Hao; Lothar Waßmann; Lucas Stach; Duan Fugang-B38611; Philippe > > Reynes; Richard Cochran; Russell King; Sascha Hauer; Stefan Agner; linux- > > kernel@vger.kernel.org; netdev@vger.kernel.org; Jeff Kirsher; Uwe Kleine- > > König > > Subject: [PATCH 2/3] net: fec: convert to using gpiod framework > > > > Use gpiod_get_optional() instead of checking for a valid GPIO number and > > calling devm_gpio_request_one() conditionally. > > > > Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> > > --- > > drivers/net/ethernet/freescale/fec_main.c | 17 +++++++---------- > > 1 file changed, 7 insertions(+), 10 deletions(-) > > > > diff --git a/drivers/net/ethernet/freescale/fec_main.c > > b/drivers/net/ethernet/freescale/fec_main.c > > index e17d74f..1a983fc 100644 > > --- a/drivers/net/ethernet/freescale/fec_main.c > > +++ b/drivers/net/ethernet/freescale/fec_main.c > > @@ -3233,7 +3233,7 @@ static int fec_enet_init(struct net_device *ndev) > > #ifdef CONFIG_OF static void fec_reset_phy(struct platform_device *pdev) > > { > > - int err, phy_reset; > > + struct gpio_desc *phy_reset; > > int msec = 1; > > struct device_node *np = pdev->dev.of_node; > > > > @@ -3245,18 +3245,15 @@ static void fec_reset_phy(struct platform_device > > *pdev) > > if (msec > 1000) > > msec = 1; > > > > - phy_reset = of_get_named_gpio(np, "phy-reset-gpios", 0); > > - if (!gpio_is_valid(phy_reset)) > > - return; > > - > > - err = devm_gpio_request_one(&pdev->dev, phy_reset, > > - GPIOF_OUT_INIT_LOW, "phy-reset"); > > - if (err) { > > - dev_err(&pdev->dev, "failed to get phy-reset-gpios: %d\n", > > err); > > + phy_reset = devm_gpiod_get_optional(&pdev->dev, "phy-reset", > > + GPIOD_OUT_LOW); > > + if (IS_ERR(phy_reset)) { > > + dev_err(&pdev->dev, "failed to get phy-reset-gpios: %ld\n", > > + PTR_ERR(phy_reset)); > > return; > > } > > msleep(msec); > > - gpio_set_value_cansleep(phy_reset, 1); > > + gpiod_set_value_cansleep(phy_reset, 1); > > This API will judge the GPIO active polarity, there many imx boards in dts files don't care the polarity. > So pls drop the patch. > > Or use gpiod_set_raw_value_cansleep() instead of gpiod_set_value_cansleep(). > I could prepare a patch that temporarily uses the raw functions and add a comment to convert these to the proper functions once all DTB files have been corrected and some time has passed to account for boards using old dtbs with newer kernels. I could also send a patch to convert all in-tree dts files to use GPIO_ACTIVE_LOW if that is desired. Lothar Waßmann -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c index e17d74f..1a983fc 100644 --- a/drivers/net/ethernet/freescale/fec_main.c +++ b/drivers/net/ethernet/freescale/fec_main.c @@ -3233,7 +3233,7 @@ static int fec_enet_init(struct net_device *ndev) #ifdef CONFIG_OF static void fec_reset_phy(struct platform_device *pdev) { - int err, phy_reset; + struct gpio_desc *phy_reset; int msec = 1; struct device_node *np = pdev->dev.of_node; @@ -3245,18 +3245,15 @@ static void fec_reset_phy(struct platform_device *pdev) if (msec > 1000) msec = 1; - phy_reset = of_get_named_gpio(np, "phy-reset-gpios", 0); - if (!gpio_is_valid(phy_reset)) - return; - - err = devm_gpio_request_one(&pdev->dev, phy_reset, - GPIOF_OUT_INIT_LOW, "phy-reset"); - if (err) { - dev_err(&pdev->dev, "failed to get phy-reset-gpios: %d\n", err); + phy_reset = devm_gpiod_get_optional(&pdev->dev, "phy-reset", + GPIOD_OUT_LOW); + if (IS_ERR(phy_reset)) { + dev_err(&pdev->dev, "failed to get phy-reset-gpios: %ld\n", + PTR_ERR(phy_reset)); return; } msleep(msec); - gpio_set_value_cansleep(phy_reset, 1); + gpiod_set_value_cansleep(phy_reset, 1); } #else /* CONFIG_OF */ static void fec_reset_phy(struct platform_device *pdev)
Use gpiod_get_optional() instead of checking for a valid GPIO number and calling devm_gpio_request_one() conditionally. Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> --- drivers/net/ethernet/freescale/fec_main.c | 17 +++++++---------- 1 file changed, 7 insertions(+), 10 deletions(-)