Message ID | 1448015861-6342-1-git-send-email-vigneshr@ti.com |
---|---|
State | Accepted |
Delegated to: | Tom Rini |
Headers | show |
On 20 November 2015 at 03:37, Vignesh R <vigneshr@ti.com> wrote: > serial_init() reads global_data, since global_data is not yet > initialized, this can cause unwanted behaviour leading to QSPI XIP boot > hang. Also, since serial_init() is anyways called later from > boar_init_f(), it does not make sense to do the same in s_init(). > > Tested on AM437x IDK EVM with QSPI XIP boot. > > Signed-off-by: Vignesh R <vigneshr@ti.com> > --- > arch/arm/cpu/armv7/am33xx/board.c | 6 ------ > 1 file changed, 6 deletions(-) Reviewed-by: Simon Glass <sjg@chromium.org> > > diff --git a/arch/arm/cpu/armv7/am33xx/board.c b/arch/arm/cpu/armv7/am33xx/board.c > index bd14326cf479..1633ddc6b096 100644 > --- a/arch/arm/cpu/armv7/am33xx/board.c > +++ b/arch/arm/cpu/armv7/am33xx/board.c > @@ -273,12 +273,6 @@ void s_init(void) > set_uart_mux_conf(); > setup_clocks_for_console(); > uart_soft_reset(); > -#if defined(CONFIG_NOR_BOOT) || defined(CONFIG_QSPI_BOOT) > - /* TODO: This does not work, gd is not available yet */ > - gd->baudrate = CONFIG_BAUDRATE; > - serial_init(); > - gd->have_console = 1; > -#endif > #if defined(CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC) > /* Enable RTC32K clock */ > rtc32k_enable(); > -- > 2.6.3 >
On Fri, Nov 20, 2015 at 04:07:41PM +0530, Vignesh R wrote: > serial_init() reads global_data, since global_data is not yet > initialized, this can cause unwanted behaviour leading to QSPI XIP boot > hang. Also, since serial_init() is anyways called later from > boar_init_f(), it does not make sense to do the same in s_init(). > > Tested on AM437x IDK EVM with QSPI XIP boot. > > Signed-off-by: Vignesh R <vigneshr@ti.com> > Reviewed-by: Simon Glass <sjg@chromium.org> Applied to u-boot/master, thanks!
diff --git a/arch/arm/cpu/armv7/am33xx/board.c b/arch/arm/cpu/armv7/am33xx/board.c index bd14326cf479..1633ddc6b096 100644 --- a/arch/arm/cpu/armv7/am33xx/board.c +++ b/arch/arm/cpu/armv7/am33xx/board.c @@ -273,12 +273,6 @@ void s_init(void) set_uart_mux_conf(); setup_clocks_for_console(); uart_soft_reset(); -#if defined(CONFIG_NOR_BOOT) || defined(CONFIG_QSPI_BOOT) - /* TODO: This does not work, gd is not available yet */ - gd->baudrate = CONFIG_BAUDRATE; - serial_init(); - gd->have_console = 1; -#endif #if defined(CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC) /* Enable RTC32K clock */ rtc32k_enable();
serial_init() reads global_data, since global_data is not yet initialized, this can cause unwanted behaviour leading to QSPI XIP boot hang. Also, since serial_init() is anyways called later from boar_init_f(), it does not make sense to do the same in s_init(). Tested on AM437x IDK EVM with QSPI XIP boot. Signed-off-by: Vignesh R <vigneshr@ti.com> --- arch/arm/cpu/armv7/am33xx/board.c | 6 ------ 1 file changed, 6 deletions(-)