Message ID | 1445376537-9291-1-git-send-email-afd@ti.com |
---|---|
State | Accepted, archived |
Delegated to: | David Miller |
Headers | show |
On 20/10/15 14:28, Andrew F. Davis wrote: > Add support for the TI DP83848 Ethernet PHY device. > > The DP83848 is a highly reliable, feature rich, IEEE 802.3 compliant > single port 10/100 Mb/s Ethernet Physical Layer Transceiver supporting > the MII and RMII interfaces. > > Signed-off-by: Andrew F. Davis <afd@ti.com> > Signed-off-by: Dan Murphy <dmurphy@ti.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Just one comment below: [snip] > diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile > index 87f079c..b748224 100644 > --- a/drivers/net/phy/Makefile > +++ b/drivers/net/phy/Makefile > @@ -24,6 +24,7 @@ obj-$(CONFIG_MDIO_BITBANG) += mdio-bitbang.o > obj-$(CONFIG_MDIO_GPIO) += mdio-gpio.o > obj-$(CONFIG_NATIONAL_PHY) += national.o > obj-$(CONFIG_DP83640_PHY) += dp83640.o > +obj-$(CONFIG_DP83848_PHY) += dp83848.o > obj-$(CONFIG_DP83867_PHY) += dp83867.o This is a pretty small PHY driver, would it make sense to look into consolidating these into e.g: dp838xx.c for instance? dp83640 is big enough to be its own driver it seems.
On 10/20/2015 04:37 PM, Florian Fainelli wrote: > On 20/10/15 14:28, Andrew F. Davis wrote: >> Add support for the TI DP83848 Ethernet PHY device. >> >> The DP83848 is a highly reliable, feature rich, IEEE 802.3 compliant >> single port 10/100 Mb/s Ethernet Physical Layer Transceiver supporting >> the MII and RMII interfaces. >> >> Signed-off-by: Andrew F. Davis <afd@ti.com> >> Signed-off-by: Dan Murphy <dmurphy@ti.com> > > Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> > > Just one comment below: > > [snip] > >> diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile >> index 87f079c..b748224 100644 >> --- a/drivers/net/phy/Makefile >> +++ b/drivers/net/phy/Makefile >> @@ -24,6 +24,7 @@ obj-$(CONFIG_MDIO_BITBANG) += mdio-bitbang.o >> obj-$(CONFIG_MDIO_GPIO) += mdio-gpio.o >> obj-$(CONFIG_NATIONAL_PHY) += national.o >> obj-$(CONFIG_DP83640_PHY) += dp83640.o >> +obj-$(CONFIG_DP83848_PHY) += dp83848.o >> obj-$(CONFIG_DP83867_PHY) += dp83867.o > > This is a pretty small PHY driver, would it make sense to look into > consolidating these into e.g: dp838xx.c for instance? dp83640 is big > enough to be its own driver it seems. > I was looking into that, but from the looks of it these drivers are small because only the functions that differentiate the PHYs need be defined. So there is very little common code between them. I'm going to be brining up a couple more PHYs soon, so I'll keep this in mind and try to find any redundancy that can be merged when working on these. Thanks, Andrew -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 20/10/15 14:51, Andrew F. Davis wrote: > On 10/20/2015 04:37 PM, Florian Fainelli wrote: >> On 20/10/15 14:28, Andrew F. Davis wrote: >>> Add support for the TI DP83848 Ethernet PHY device. >>> >>> The DP83848 is a highly reliable, feature rich, IEEE 802.3 compliant >>> single port 10/100 Mb/s Ethernet Physical Layer Transceiver supporting >>> the MII and RMII interfaces. >>> >>> Signed-off-by: Andrew F. Davis <afd@ti.com> >>> Signed-off-by: Dan Murphy <dmurphy@ti.com> >> >> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> >> >> Just one comment below: >> >> [snip] >> >>> diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile >>> index 87f079c..b748224 100644 >>> --- a/drivers/net/phy/Makefile >>> +++ b/drivers/net/phy/Makefile >>> @@ -24,6 +24,7 @@ obj-$(CONFIG_MDIO_BITBANG) += mdio-bitbang.o >>> obj-$(CONFIG_MDIO_GPIO) += mdio-gpio.o >>> obj-$(CONFIG_NATIONAL_PHY) += national.o >>> obj-$(CONFIG_DP83640_PHY) += dp83640.o >>> +obj-$(CONFIG_DP83848_PHY) += dp83848.o >>> obj-$(CONFIG_DP83867_PHY) += dp83867.o >> >> This is a pretty small PHY driver, would it make sense to look into >> consolidating these into e.g: dp838xx.c for instance? dp83640 is big >> enough to be its own driver it seems. >> > > I was looking into that, but from the looks of it these drivers are small > because only the functions that differentiate the PHYs need be defined. > So there is very little common code between them. > > I'm going to be brining up a couple more PHYs soon, so I'll keep this in > mind > and try to find any redundancy that can be merged when working on these. Sounds good, thanks for giving some context on this.
On 10/20/2015 04:28 PM, Andrew F. Davis wrote: > Add support for the TI DP83848 Ethernet PHY device. > > The DP83848 is a highly reliable, feature rich, IEEE 802.3 compliant > single port 10/100 Mb/s Ethernet Physical Layer Transceiver supporting > the MII and RMII interfaces. > > Signed-off-by: Andrew F. Davis <afd@ti.com> > Signed-off-by: Dan Murphy <dmurphy@ti.com> > --- > drivers/net/phy/Kconfig | 5 +++ > drivers/net/phy/Makefile | 1 + > drivers/net/phy/dp83848.c | 99 +++++++++++++++++++++++++++++++++++++++++++++++ > 3 files changed, 105 insertions(+) > create mode 100644 drivers/net/phy/dp83848.c > > diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig > index c5ad98a..12fa29a 100644 > --- a/drivers/net/phy/Kconfig > +++ b/drivers/net/phy/Kconfig > @@ -122,6 +122,11 @@ config MICREL_PHY > ---help--- > Supports the KSZ9021, VSC8201, KS8001 PHYs. > > +config DP83848_PHY > + tristate "Driver for Texas Instruments DP83848 PHY" > + ---help--- > + Supports the DP83848 PHY. > + > config DP83867_PHY > tristate "Drivers for Texas Instruments DP83867 Gigabit PHY" > ---help--- > diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile > index 87f079c..b748224 100644 > --- a/drivers/net/phy/Makefile > +++ b/drivers/net/phy/Makefile > @@ -24,6 +24,7 @@ obj-$(CONFIG_MDIO_BITBANG) += mdio-bitbang.o > obj-$(CONFIG_MDIO_GPIO) += mdio-gpio.o > obj-$(CONFIG_NATIONAL_PHY) += national.o > obj-$(CONFIG_DP83640_PHY) += dp83640.o > +obj-$(CONFIG_DP83848_PHY) += dp83848.o > obj-$(CONFIG_DP83867_PHY) += dp83867.o > obj-$(CONFIG_STE10XP) += ste10Xp.o > obj-$(CONFIG_MICREL_PHY) += micrel.o > diff --git a/drivers/net/phy/dp83848.c b/drivers/net/phy/dp83848.c > new file mode 100644 > index 0000000..5ce9bef > --- /dev/null > +++ b/drivers/net/phy/dp83848.c > @@ -0,0 +1,99 @@ > +/* > + * Driver for the Texas Instruments DP83848 PHY > + * > + * Copyright (C) 2015 Texas Instruments Inc. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; either version 2 of the License. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + */ > + > +#include <linux/module.h> > +#include <linux/phy.h> > + > +#define DP83848_PHY_ID 0x20005c90 > + > +/* Registers */ > +#define DP83848_MICR 0x11 > +#define DP83848_MISR 0x12 > + > +/* MICR Register Fields */ > +#define DP83848_MICR_INT_OE BIT(0) /* Interrupt Output Enable */ > +#define DP83848_MICR_INTEN BIT(1) /* Interrupt Enable */ > + > +/* MISR Register Fields */ > +#define DP83848_MISR_RHF_INT_EN BIT(0) /* Receive Error Counter */ > +#define DP83848_MISR_FHF_INT_EN BIT(1) /* False Carrier Counter */ > +#define DP83848_MISR_ANC_INT_EN BIT(2) /* Auto-negotiation complete */ > +#define DP83848_MISR_DUP_INT_EN BIT(3) /* Duplex Status */ > +#define DP83848_MISR_SPD_INT_EN BIT(4) /* Speed status */ > +#define DP83848_MISR_LINK_INT_EN BIT(5) /* Link status */ > +#define DP83848_MISR_ED_INT_EN BIT(6) /* Energy detect */ > +#define DP83848_MISR_LQM_INT_EN BIT(7) /* Link Quality Monitor */ > + > +static int dp83848_ack_interrupt(struct phy_device *phydev) > +{ > + int err = phy_read(phydev, DP83848_MISR); > + > + return err < 0 ? err : 0; > +} > + > +static int dp83848_config_intr(struct phy_device *phydev) > +{ > + int err; > + > + if (phydev->interrupts == PHY_INTERRUPT_ENABLED) { > + err = phy_write(phydev, DP83848_MICR, > + DP83848_MICR_INT_OE | > + DP83848_MICR_INTEN); > + if (err < 0) > + return err; > + > + return phy_write(phydev, DP83848_MISR, > + DP83848_MISR_ANC_INT_EN | > + DP83848_MISR_DUP_INT_EN | > + DP83848_MISR_SPD_INT_EN | > + DP83848_MISR_LINK_INT_EN); > + } > + > + return phy_write(phydev, DP83848_MICR, 0x0); > +} > + > +static struct mdio_device_id __maybe_unused dp83848_tbl[] = { > + { DP83848_PHY_ID, 0xfffffff0 }, > + { } > +}; > +MODULE_DEVICE_TABLE(mdio, dp83848_tbl); > + > +static struct phy_driver dp83848_driver[] = { > + { > + .phy_id = DP83848_PHY_ID, > + .phy_id_mask = 0xfffffff0, > + .name = "TI DP83848", > + .features = PHY_BASIC_FEATURES, > + .flags = PHY_HAS_INTERRUPT, > + > + .soft_reset = genphy_soft_reset, > + .config_init = genphy_config_init, > + .suspend = genphy_suspend, > + .resume = genphy_resume, > + .config_aneg = genphy_config_aneg, > + .read_status = genphy_read_status, > + > + /* IRQ related */ > + .ack_interrupt = dp83848_ack_interrupt, > + .config_intr = dp83848_config_intr, > + > + .driver = { .owner = THIS_MODULE, }, > + }, > +}; > +module_phy_driver(dp83848_driver); > + > +MODULE_DESCRIPTION("Texas Instruments DP83848 PHY driver"); > +MODULE_AUTHOR("Andrew F. Davis <afd@ti.com"); > +MODULE_LICENSE("GPL"); Acked-by: Dan Murphy <dmurphy@ti.com> I know I have my SoB but figured I would give an Acked-by too
From: "Andrew F. Davis" <afd@ti.com> Date: Tue, 20 Oct 2015 16:28:57 -0500 > Add support for the TI DP83848 Ethernet PHY device. > > The DP83848 is a highly reliable, feature rich, IEEE 802.3 compliant > single port 10/100 Mb/s Ethernet Physical Layer Transceiver supporting > the MII and RMII interfaces. > > Signed-off-by: Andrew F. Davis <afd@ti.com> > Signed-off-by: Dan Murphy <dmurphy@ti.com> Applied, thanks. -- To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig index c5ad98a..12fa29a 100644 --- a/drivers/net/phy/Kconfig +++ b/drivers/net/phy/Kconfig @@ -122,6 +122,11 @@ config MICREL_PHY ---help--- Supports the KSZ9021, VSC8201, KS8001 PHYs. +config DP83848_PHY + tristate "Driver for Texas Instruments DP83848 PHY" + ---help--- + Supports the DP83848 PHY. + config DP83867_PHY tristate "Drivers for Texas Instruments DP83867 Gigabit PHY" ---help--- diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile index 87f079c..b748224 100644 --- a/drivers/net/phy/Makefile +++ b/drivers/net/phy/Makefile @@ -24,6 +24,7 @@ obj-$(CONFIG_MDIO_BITBANG) += mdio-bitbang.o obj-$(CONFIG_MDIO_GPIO) += mdio-gpio.o obj-$(CONFIG_NATIONAL_PHY) += national.o obj-$(CONFIG_DP83640_PHY) += dp83640.o +obj-$(CONFIG_DP83848_PHY) += dp83848.o obj-$(CONFIG_DP83867_PHY) += dp83867.o obj-$(CONFIG_STE10XP) += ste10Xp.o obj-$(CONFIG_MICREL_PHY) += micrel.o diff --git a/drivers/net/phy/dp83848.c b/drivers/net/phy/dp83848.c new file mode 100644 index 0000000..5ce9bef --- /dev/null +++ b/drivers/net/phy/dp83848.c @@ -0,0 +1,99 @@ +/* + * Driver for the Texas Instruments DP83848 PHY + * + * Copyright (C) 2015 Texas Instruments Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/module.h> +#include <linux/phy.h> + +#define DP83848_PHY_ID 0x20005c90 + +/* Registers */ +#define DP83848_MICR 0x11 +#define DP83848_MISR 0x12 + +/* MICR Register Fields */ +#define DP83848_MICR_INT_OE BIT(0) /* Interrupt Output Enable */ +#define DP83848_MICR_INTEN BIT(1) /* Interrupt Enable */ + +/* MISR Register Fields */ +#define DP83848_MISR_RHF_INT_EN BIT(0) /* Receive Error Counter */ +#define DP83848_MISR_FHF_INT_EN BIT(1) /* False Carrier Counter */ +#define DP83848_MISR_ANC_INT_EN BIT(2) /* Auto-negotiation complete */ +#define DP83848_MISR_DUP_INT_EN BIT(3) /* Duplex Status */ +#define DP83848_MISR_SPD_INT_EN BIT(4) /* Speed status */ +#define DP83848_MISR_LINK_INT_EN BIT(5) /* Link status */ +#define DP83848_MISR_ED_INT_EN BIT(6) /* Energy detect */ +#define DP83848_MISR_LQM_INT_EN BIT(7) /* Link Quality Monitor */ + +static int dp83848_ack_interrupt(struct phy_device *phydev) +{ + int err = phy_read(phydev, DP83848_MISR); + + return err < 0 ? err : 0; +} + +static int dp83848_config_intr(struct phy_device *phydev) +{ + int err; + + if (phydev->interrupts == PHY_INTERRUPT_ENABLED) { + err = phy_write(phydev, DP83848_MICR, + DP83848_MICR_INT_OE | + DP83848_MICR_INTEN); + if (err < 0) + return err; + + return phy_write(phydev, DP83848_MISR, + DP83848_MISR_ANC_INT_EN | + DP83848_MISR_DUP_INT_EN | + DP83848_MISR_SPD_INT_EN | + DP83848_MISR_LINK_INT_EN); + } + + return phy_write(phydev, DP83848_MICR, 0x0); +} + +static struct mdio_device_id __maybe_unused dp83848_tbl[] = { + { DP83848_PHY_ID, 0xfffffff0 }, + { } +}; +MODULE_DEVICE_TABLE(mdio, dp83848_tbl); + +static struct phy_driver dp83848_driver[] = { + { + .phy_id = DP83848_PHY_ID, + .phy_id_mask = 0xfffffff0, + .name = "TI DP83848", + .features = PHY_BASIC_FEATURES, + .flags = PHY_HAS_INTERRUPT, + + .soft_reset = genphy_soft_reset, + .config_init = genphy_config_init, + .suspend = genphy_suspend, + .resume = genphy_resume, + .config_aneg = genphy_config_aneg, + .read_status = genphy_read_status, + + /* IRQ related */ + .ack_interrupt = dp83848_ack_interrupt, + .config_intr = dp83848_config_intr, + + .driver = { .owner = THIS_MODULE, }, + }, +}; +module_phy_driver(dp83848_driver); + +MODULE_DESCRIPTION("Texas Instruments DP83848 PHY driver"); +MODULE_AUTHOR("Andrew F. Davis <afd@ti.com"); +MODULE_LICENSE("GPL");